Farmall & IHC Tractors Discussion Board |
Hey guys, check this out!! Farmall H for $5000
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Steven@nd on February 13, 2002 at 12:13:49 from (165.234.131.197):
NO PICTURE!! What a joke! How can you get a bid for something like that without a picture? I doubt anyone ever will bid. Check out the link. Steven
Follow Ups:
- Re: Hey guys, check this out!! Farmall H for $5000 Bob Kerr 09:59:22 02/14/02
(3)
- Re: Hey guys, check this out!! Farmall H for $5000 Red Rider 20:02:51 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 John M 17:38:27 02/13/02
(1)
- Re: Hey guys, check this out!! Farmall H for $5000 Irv 17:29:53 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 Zack 17:14:22 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 Farmall-Nut 16:53:08 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 williamf 16:38:07 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 John Mann 15:59:39 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 Greaseman 15:57:21 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 Keith 14:40:50 02/13/02
(2)
- Re: Hey guys, check this out!! Farmall H for $5000 Mike Christian 14:31:10 02/13/02
(0)
- Re: Hey guys, check this out!! Farmall H for $5000 jal-SD 13:24:55 02/13/02
(2)
- Re: Hey guys, check this out!! Farmall H for $5000 Sam 12:35:49 02/13/02
(2)
- Re: Hey guys, check this out!! Farmall H for $5000 lcbateman 12:33:28 02/13/02
(1)
Home
| Forums
Today's Featured Article -
Measuring with Calipers - by Staff. The legs of inside calipers are curved outward at the extremities to facilitate measuring small holes, while outside caliper legs have a large curve inward to increase their capacity for large work. Firm-joint calipers are adjusted approximately by the hands and then set to the feel of the work by tapping them on a metal surface. It is a common practice when opening calipers by this means to tap the top of the joint. It is better, if possible, to tap the inside of the legs, as repeated blo
... [Read Article]
Latest Ad:
Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use.
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|