International Harvester / Farmall Super W9 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Pedal Shaft Seal - This Seal is used as a brake pedal shaft seal, (2 used per tractor) on Farmall / International: W9, WD9, WR9, Super WDR9, Super WD9, WDR9, WR9S, 600, 650, Super W9, Super WR9S. It measures 1.375 inch inside diameter, 2.130 inch outside diameter, and 0.437 inch wide. Replaces 0511073, 1K1590, 1K1590, 224810, 230608, 241779, 340214, 35451D, 357970R91, 357976R91, 380184R91, 43509D, 43509DA, 511073, 527829R91, 60454D, 659124R91, 70224810, 70230608, 70241779, 70241D, 938294R91, 938294R92, AH14076, AL2094T, AL56820, AM253T, AN30648, AN32717, AP24021, K1590, K1590, M86688, N71730N, T22069 (Item #: 128541, Ref: 70241779) $7.70

Clutch
Clutch Disc, Remanufactured, Minneapolis Moline - For International / Farmall tractor models Super W9, W9, 650, Compatible with Minneapolis Moline tractor models UB, Clutch Size: 12", Clutch Hub: 1-3/4", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: Woven, (Item #: 206004) $105.50

Cooling System
Radiator Cap - 7 pound, fits short filler neck. For tractor models 100, 130, 140, 1410, 1412, 1440, 1460, (1640 serial number 44C0034705 and below), (1660 serial number JJC0038346 and below), (1680 serial number JJC0045689 and below), 1822, 1844, 200, 2022, 230, 240, 2400A, 2424, 2444, 2500A, 2504, 2606, 300, 330, 3388, 340, 350, 3588, 3788, 400, 404, 4100, 4156, 4166, 424, 4366, 4386, 444, 450, 4568, 460, 464, 474, 4786, 504, 560, 606, 6388, 656, 6588, 660, 6788, 706, 806, 990, Hydro 84, Super H, Super M, Super MD, Super W4, Super W6, Super W9, Super WD6, Super WD9. (Item #: 112331, Ref: 180224M91) $6.60
Radiator Cap - Fits Super A, Super C, Super H, M, MD, Super M, MD, 4, Super W4, O6, W6, ODS6, Super W6 and WD6, W9, WD9, Super W9 and WD9. Not for short filler neck. (Item #: 112290, Ref: 67448DD) $3.98
Radiator Cap - 7 pound pressure radiator cap. Cap measures 2.328 inches diameter less finger tabs. Inside diameter is 2.215 and 1.970 inches between locking tabs. (** = FOR SHORT FILLER NECK). Fits **Super H, **Super M, MD, **Super W4, **Super W6 and WD6, **Super W9 and WD9, **100, **130, **140, **200, **230, 240, **300, **330, 340, **350, **400, 404, **424, **444, **450, **460, **504, **560, 606, **660, 2424, 2444, 2504, 2606, 4100, 4156, 4166. Replaces OEM 393229R91. (Item #: 112331, Ref: 180224M91) $6.60
Radiator Cap With Lever - Pressure cap with lever. For C, H, M, MD, O6, ODS6, Super C, Super H, Super M, Super MD, Super W4, Super W6, Super W9, Super WD6, Super WD9, Super A, W4, W6, W9, WD9 (Item #: 110150, Ref: 67448DDWL) $17.00

Decals and Emblems
No Picture Decal Set - For Super W9. Complete Decal Set. (Item #: MDSW9) $110.12
Hood Emblem - For Super H, Super HV, Super M, Super MTA, Super W4, Super W6, W6TA, Super W9, WD9. Hood Emblem "IH" is 2-1/2 inch x 2-3/4 inch. (Item #: 103914, Ref: 357650R1) $15.50
IH Decal, 1-5/8", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1 5/8", no background, (Item #: 101024) $2.80
IH Decal, 1", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1", no background, (Item #: 101023) $1.90
IH Decal, 3" x 3-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 3" x 3-1/2", No background, (Item #: 101025) $11.20
IH Decal, 4-1/2" x 5" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 4-1/2" x 5", Mylar decal, (Item #: 101095) $5.60
International Decal, 17", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 17" long, Black, Mylar decal, (Item #: 101105) $5.60
International Decal, 8-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 8 1/2" long, Black, Mylar decal, (Item #: 101104) $3.80
International Decal Set,10" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 10", (Item #: 101022) $29.70
International Decal Set, 1 1/4" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-1/4", (Item #: 101018) $2.80
International Decal Set, 1 3/4"x 1 5/8" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-3/4", (Item #: 101019) $3.80
No Picture International Decal Set, 6 1/2"x 7" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo 7", Vinyl Cut, Shaded Outline, (Item #: 101020) $16.80
No Picture International Decal Set, 7 1/4"x 8" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 8", (Item #: 101021) $22.30
International Harvester Decal, 2-3/4" x 3" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, (Item #: 101093) $3.80
International Harvester Decal, 2" x 2-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/2", No background, Mylar decal, (Item #: 101097) $3.80
International Harvester Decal, 2" x 2-1/4", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/4", Mylar decal, (Item #: 101092) $3.80
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", Mylar decal, (Item #: 101096) $5.60
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", No background, Mylar decal, (Item #: 101098) $5.60
International Harvester Decal, 5" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 5" diameter, Shaded outline, Mylar decal, (Item #: 101099) $5.60
International Harvester Decal, 6" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 6" diameter, Shaded outline, Mylar decal, (Item #: 101100) $7.50
International Harvester Decal, 7-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 7 1/2" diameter, Shaded outline, Mylar decal, (Item #: 101101) $9.30
International Harvester Decal, 9", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 9" diameter, Shaded outline, Mylar decal, (Item #: 101102) $11.20
International Hood Decal, 23-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, Size: 23-1/2", Black lettering, (Item #: 101031) $14.90
McCormick International Decal, 10" Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 10" long, Black and white, Vinyl decal, (Item #: 101103) $9.30
McCormick International Decal, Hood, White/Black, 7-1/4", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 7-1/4" black and white, Vinyl decal, (Item #: 101026) $7.50

Electrical System
Coil, Original, 12 Volt - OEM style coil. For tractor models 100, A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, MD, W4, W6, Super W4, Super W6, Super W6TA, W9, Super W9, Cub, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450. This is an International Harvester OEM style 12 volt distributor coil. This distributor coil has a 2.8 ohm rating between the two primary winding terminals. Requires an external resistor. (Item #: 154651, Ref: 353875R91) $65.00
Coil, Original, 6 Volt - OEM style coil. Measures overall length of 5 3/8 inches, Diameter at widest point of center ridge is 2 1/4 inches. This distributor coil has a 1.4 ohm rating between the two primary winding terminals. For tractor models 100, A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, MD, W4, W6, Super W4, Super W6, Super W6TA, W9, Super W9, Cub, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450. (Item #: 154650, Ref: 353874R91) $66.00
Distributor - Original IHC design comes with a 32 tooth drive gear. For tractor models Super W6TA, Super W9, Super WD6, Super WD6-TA, Super WD9, Super WDR9, W4, W400, W450, W6, W9, WD6, WD9, WDR9, WR9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 504, 600, 650, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 3514. R6332. MHSK1 (Item #: 124839, Ref: 107304C91) $120.00
Distributor Drive Housing - This is a new distributor drive housing with an opening for tachometer drive. It is used to change from a magneto to a distributor or to add a tachometer drive to your tractor. The tachometer drive parts (tachometer drive assembly part number 369695R1, tachometer cable connector housing, part number 369692R1 and 363817R1, connection housing plate) or tach. Drive blockoff plate are sold separately. NOTE: Will also work on tractors without tach drive by ordering number 363764R1 block off plate. Use with 107304C91 distributor when replacing a magneto. fits tractor models A, A1, AV, AV-1, B, BN, C, Cub, Cub Lo-Boy, H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W9, W4, W6, W6TA, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 2504, 300, 330, 340, 3444, 350, 3514, 404, 424, 444, 504, 400, 600, 650 450. Replaces: 363749R91, 363763R11. (Item #: 178938, Ref: 363749R91) $108.00
Distributor Hold Down Clamp - For 5/16 inch hold down bolt and IH built distributor. 2 used per engine, sold individually. Fits fits tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, H, HV, Hydro 70, Hydro 86, I4, I6, I9, ID6, ID9, M, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, W4, W6, W9, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 2505B, 2510B, 2514B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 574, 600, 606, 650, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856. All with IH distributors. Replaces 341139R1, 353937R1. (Item #: 182464, Ref: 341139R1) $9.20
Electronic Ignition Conversion Kit - 12v Negative Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt NEGATIVE ground system only. Distributors with clip type cap. (Item #: 105071, Ref: 1142) $155.00
Electronic Ignition Conversion Kit - 12v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. 1885368 or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt POSITIVE ground system only. (Item #: 108148, Ref: 1142P12) $177.00
Electronic Ignition Conversion Kit, 6v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with Delco distributor part no. 1885368 with clip type cap. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 6 volt positive ground system only. (Item #: 105072, Ref: 1142P6) $160.00
Generator Belt - Fits some of the following Farmall / International Diesel Tractors: B275, B414, MD, Super W9, 354, 364. This Wedge Belt measures 0.531 X 30.27 inches. Verify measurements or part number before ordering. These model tractors used more than one size. Replaces 376370R1, 54857DB, 704449R1 (Item #: 123135, Ref: 376370R1) $6.30
Generator - Delco Style (10181), Remanufactured, Delco Remy, 1101355 - For International / Farmall tractor models Cub, Super W4, Super W6, Super W9, Replaces Delco Remy manufacturer number 1101355, 1101358, 1101369, 1101423, Replaces manufacturer number 10181, 340-22, 92-01-3050, Delco Style, Voltage: 6, Rotation: Clockwise, Amperage: 14, Regulator: External, Has long shaft for extended pulley, Has screw holes for regulator mount - regulator not included, For Voltage Regulator use Item #: 105284, (Item #: 203180) $430.80
No Picture Generator - Delco Style (9246), Remanufactured, Delco Remy, 1100964 - For International / Farmall tractor models I6, I9, MD, OS6, Super W6, Super W9, W400, W450, 400, 450, Compatible with International Construction and industrial models TD6, TD9, TD14, Replaces Delco Remy manufacturer number 1100964, Replaces manufacturer number 9246, 340-89, 92-01-3051, Delco Style, Voltage: 12, Rotation: Clockwise, Amperage: 13, Regulator: External, (Item #: 203516) $365.01
No Picture Generator - Delco Style (9718), Remanufactured, Delco Remy, 1100501 - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, I9, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, Compatible with International Combine (s) 101, 140, 151, Compatible with International Construction and industrial models T6, Compatible with International Baler (s) 37, 47, 57, Replaces Delco Remy manufacturer number 1100501, Replaces manufacturer number 9718, 340-21, 92-01-3050, Delco Style, Voltage: 6, Rotation: Clockwise, Amperage: 25, Regulator: External, (Item #: 203178) $408.38
H4 Magneto Pinion Driven Gear - This gear has 24 teeth and measures: 0.380 inch inside diameter, 0.759 inch outside diameter, 1.075 inch gear outside diameter, 0.952 inch overall height. It is used on H4 Magnetos. (Item #: 183878, Ref: 49420DX) $26.20
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.90
Starter - Delco Style (4132), Remanufactured, Delco Remy, 1107427, 104219A2 - For International / Farmall tractor models H (s/n 19233-earlier), HV, I4, M (s/n 28174-earlier), MTA, O4, O6, O9, OS4, OS6, Super H, Super W4, Super W6, Super W9, W4, Replaces International OEM number 104219A2, 997870R91, 104219A2R, Replaces Delco Remy manufacturer number 1107427, 1107448, Replaces manufacturer number 4132, 140-013, 91-01-3639, Delco Style, Voltage: 12, Rotation: Counter Clockwise, Teeth: 10, For 6 Volt use Item #: 203150, Additional Handling and Oversize Fees Apply To This Item, (Item #: 210141) $334.01
No Picture Starter - Delco Style (4646), Remanufactured, 61061DA, Delco Remy, 1108913 - For International / Farmall tractor models I6, I9, MD, MTA, OS6, Super W6, Super W9, Replaces Case OEM number 61061DA, Replaces Delco Remy manufacturer number 1108913, Replaces manufacturer number 4646, 140-0961, 91-01-3978, Delco Style, Voltage: 12, Rotation: Counter Clockwise, Teeth: 12, (Item #: 205608) $480.01
No Picture Starter - Delco Style (4651), Remanufactured, Delco Remy, 1108920 - For International / Farmall tractor models Super W9, W9, Replaces Delco Remy manufacturer number 1108920, 1108943, Replaces manufacturer number 4651, 140-073, Delco Style, Voltage: 6, Rotation: Clockwise, Teeth: 10, (Item #: 205575) $620.01
No Picture Starter - Delco Style DD (4132), Remanufactured, Delco Remy, 1107427, 104219A2 - For International / Farmall tractor models H (s/n 19233-earlier), HV, I4, M (s/n 28174-earlier), MTA, O4, O6, O9, OS4, OS6, Super H, Super W4, Super W6, Super W9, W4, Replaces International OEM number 104219A2, 997870R91, 104219A2R, Replaces Delco Remy manufacturer number 1107427, 1107448, Replaces manufacturer number 4132, 140-013, 91-01-3639, Delco Style: Direct Drive, Voltage: 6, Rotation: Counter Clockwise, Teeth: 10, For a New version of this sku use Item #: 109769, (Item #: 203150) $353.37
Wiring Harness Grommet - For International / Farmall tractor models A, B, C, H, HV, I4, I6, I9, M, MD, O4, O6, OS4, OS6, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, Replaces International OEM number 52062D, Mounts in amp box, Outer Diameter: 1.810", Inner Diameter: 1.246", (Item #: 126808) $5.50

Engine Gaskets
Crank Seal, Front - This front crankshaft oil seal has a 2.625 inch Inside Diameter, a 3.38 inch Outside Diameter and is .475 inch wide. It Fits: I6, I9, ID6, ID9, M, MD, MDV, MV, O6, ODS6, OS6, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, T6, T6-61, T9, TD6, TD6-61, TD9, TD9-91, W400, W450, W6, W9, WR9, WR9S, 400, 450, 600, 650, B-450, BM, BMD, SBMD, Super BM. Replaces: 258511R91, 357972R91, 357977R91, 358511R91, 53872D, 410708 (Item #: 106640, Ref: 357972R1) $13.60

Engine Parts
No Picture Connecting Rod Bolt Lock Tab - For Diesel models: I9, ID6, MD, MDV, ODS6, Super MD, Super MDV, Super MDV-TA, Super MTA, 400, 450, Super W9, T9, TD6, TD9, W9, WD6, WR9, WR95. GAS and LP: 600, 650. (Item #: 167084, Ref: 253220R1) $7.70
No Picture Cylinder Head, Remanufactured, 8320D - For International / Farmall tractor models Super W9, W9 (Gas), 600, 650, Replaces International Casting number 8320D, Casting No. 8320D, Engines 350, Cylinders: 4, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 205493) $1450.01
No Picture Cylinder Head, Remanufactured, 9195D - For International / Farmall tractor models Super W9, W9 (Gas), 600, 650, Replaces International Casting number 9195D, Engine 350, Cylinders 4, Casting No. 9195D, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200193) $288.01
Valve Lifter - This valve lifter / tappet is used on International engines C248, C264, C281, D248, D264, D281. Measures; Length: 2.655 inches, Diameter: 1.243 inches, Inside Diameter: 1.042 inches, Hole Inside Diameter: .255 inches. Replaces 45956D, 684414C1 (Item #: 192210) $24.40

Fuel System / Air Intake
Sediment Bowl Assembly Glass Bowl - Glass bowl with an outside diameter is 2 1/8 and an overall height of 2 3/8. For the following models using a 2 3/8 inch tall glass bowl: O12, O14, O4, O6, OS4, OS6, T340, T5, T6 (up to serial number 29964), W12, W14, W30, Super W4, W4, W40, Super W6, Super W6TA, W6, Super W9, W9, WR9S, F12, F14, F20, F30, 100, 130, 140, 200, 230, 300, 340, 350, 400, W400, 450, W450, 460, 560, 656, 660, 706, 756, 766, 806, 826, 856. Replaces 51344VA and 357957R1. (Item #: 105365, Ref: S.65504) $6.10
Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. (Item #: 105364, Ref: 49923D) $3.30

Gauges
Oil Gauge - Oil pressure gauge, 80 pound, fits 2 inch diameter hole. For 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, W4, 400, W6, W9, A, B, C, H, M, Super C, Super W9, Super A. Replaces 536962R1, 536962R2. (Item #: 110411, Ref: FAD9273A) $14.50
Oil Pressure Gauge - For International / Farmall tractor models I6, M, Super M, Super MTA, Super W6, Super W9, TD6, TD9, W6, W9, Replaces International OEM number 258634R91, 702027C1, IH Logo on Face, Dash Mounted, 0-45 PSI, (Item #: 121660) $47.00
Oil Pressure Gauge - Zone Style - with IH Logo with studs - Does not include bracket. For H, Super H, M, Super M, Super MTA, W-4, Super W4, W-6, Super W6, W-9, Super W9 (from 1947). (Item #: 110849, Ref: 41934DB) $45.20

Hitch / Drawbar
Drawbar Pin Retainer Plate - Used on the following Farmall / International models: H, M, 560, 806, 1066, MD, MTA, W6TA, W9, O4, WD9, WR9, Super WDR9, OS4, Super H, Super M, Super MD, Super MTA, Hydro 84, Super W4, Super W6, Super W6TA, Super WD6, Super WD9, W4, W6, WD6, WDR9, WR9S, 300, 330, 340, 350, 400, 450, 454, 460, 464, 504, 544, 574, 600, 606, 650, 656, 660, 664, 666, 674, 706, 756, 766, 826, 284, 856, 966, 1026, 385, 484, 584, 684, 686, 784, 884, Super MDTA, Super WD6TA, Super WR9S, Super W9, WD6TA, this part measures 1.480 inches long, 1 inch wide and has a 0.377 inch hole diameter and 0.193 inch thick. Many of the listed models used a round plate rather than the rectangular one. This part will replace the round version. Replaces OEM numbers 132794H1, 491390, 49139D, 57654D, 57655D, 58657D (Item #: 112643, Ref: 49139D) $7.50

Hydraulic System
Hydraulic Manifold - Hydraulic Pump Flange, Hydraulic Manifold, Port Block is used on (M, Super M, 400, 450 Gas or Diesel), Super W6, Super W9, Super WD6, Super WD9, W6, W9, WD6, WD9, 600, 650. 3/4 inch NPT inlet and outlet. Threaded for hydraulic hose. Must use rubber hose lines. (Item #: 115188, Ref: IHS1240) $71.00
Hydraulic Pump - For block style lines that mount to bottom of pump. This is a cast aluminum style and will not directly replace cast iron style (it will replace if you have a plate manufactured to adapt the type of hose connections as is on your old pump). For tractor models Super M, Super MTA, Super W6, Super W9, 400, 450. All Gas with Live Hydraulics. Replaces 128190C91, 357214R92, 362175R94 (Item #: 102180, Ref: 128190C91) $623.00

Lights
Rear Combo Light Assembly -6Volt - Replaces 355911R91, manufactured to restoration standards. Rear combo light assembly, 6 Volt. Includes red jewel light with rotary switch. For: Cub, Super A and AV, C, Super C, H, HV, Super H and HV, M, MD, MDV, MV, Super M and MTA, O4, o6, ODS6, OS6, W6, WD6, W6TA, Super W6, W9, WDR9, WR9, Super W9, 100, 130, 140, 230, 240, 300, 330, 340, 350, 400, 450. (Item #: 105335, Ref: 355914R91-6V) $73.00

Oil System
Oil Pan Drain Plug - White Zinc Finish, 7/8 inch - 18 UNF. Fits multiple models. Order EBU6734A if washer is needed. Replaces: 688067C1, 359875R1. (Item #: 126591, Ref: C5NE6730B) $8.10
Oil Pan Drain Plug Washer - This washer is used with C5NE6730B 7/8 inch Oil Drain Plug. (Item #: 140612, Ref: EBU6734A) $1.70

PTO / Driveline
PTO Seal - Measures 1.306 inch inside diameter, 2.220 inch outside diameter. THIS SEAL IS .312 InchES WIDE. VERIFY THE WIDTH OF YOUR OLD SEAL. YOU NEED TO INSTALL 2 OF THESE IF YOUR OLD SEAL IS WIDER. For tractor models Super A, H after serial number 118000, (M, MD, Super M, Super MTA and Super MD after serial number 59957), Late W4, W6, W9, Super W4, Super W6, Super W9, B250, B275, B414; Also fits the following models with transmission driven PTO (not Live PTO): MTA, 300, 330, 350, 354, 364, 384, 400, 424, 434, 444, 450, 454, 544, 600, 650, 2300, 3414, 3514, 3616. Replaces 3065217R91, 358772R91, 358812R91, 50702D, 372394R91, S90957, 708107R91. (Item #: 114730, Ref: 45702D) $9.80

Sheet Metal / Body Parts
Wire Grille Screen Clips - 6 pack - For International / Farmall tractor models A, B, C, Cub, H, M, Super A, Super C, Super H, Super M, Super W4, Super W6, Super W9, Sold in packs of 6, (Item #: 108001) $8.00

Steering
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00

Wheels
Rear Wheel Rim Clamp Bolt - For International / Farmall tractor models H, HV, M, MD, MTA, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super W9, W4, W6, W9, WD9, 300, 400 (s/n 5180-earlier), Replaces International OEM number 48985DA, 13491R1, 4.25" x 5/8" NC, Square head 1", Grade 5, Single Dot Square Head, (Item #: 126624) $14.40
Rubber Bushing Retainer - For International / Farmall tractor models A, B, C, Cub, H, I4, O4, Super A, Super C, Super H, Super M, Super W4, Super W6, Super W9, W4, W6, 100, 130, 140, 200, 230, 600, 650, Replaces International OEM number 50942D, (Item #: 126651) $3.80
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $365.01
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.87
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.10
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.60
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $4.90
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.80
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.50
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.10
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.10
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.80
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $4.90
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.00
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.40
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.40
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.30
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.60
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.00
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.10
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.30
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.30
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.40
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.60
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.90
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $11.20
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $18.60

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $94.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.50
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.90
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.20
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.80
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $27.00

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $78.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $108.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $176.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.80
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $11.00
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $12.70
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.10
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $28.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $59.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $39.90
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $45.20
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $14.90

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $367.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $440.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $440.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.28
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $25.70
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $14.70
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.60
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.60

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $120.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.70
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.80
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $98.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $45.00
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $42.00
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.70
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $42.00
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $390.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $119.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.40
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $68.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $54.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.30
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $55.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.90
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $58.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $23.30
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $9.40
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $23.30
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.50
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $86.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.10
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $12.50
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $60.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $23.70
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $7.80
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $60.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $16.90
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.90
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $16.90
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $7.90
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $44.10

PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $173.00
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00
NOTE PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.	NOTE
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $279.00