Center Link Assembly (Cat III) - Note: This Assembly consist of one each of 1981986C1 front end, 1282063C2 rear end, and 1954221C3 center. The complete assembly will work for models 1066-6788 however the individual components are not interchangeable with original equipment and you must use the whole assembly. Components are compatible and interchangeable with original equipment on models 7110-8950. 1066, 1086, 1456, 1466, 1486, 1566, 1568, 1586, 3088, 3288, 3388, 3488, 3588, 3688, 5088, 5288, 5488, 6388, 6588, 6788, 21206, 21256, 21456, 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 8910, 8920, 8930, 8940, 8950, 9310, 9330, 9350. The ends are 1.500 inch thread. Replaces 108591C91, 1252108C92, 1252108C94, 1331853C2, 1331854C1, 1331855C1, 1331855C3 (Item #: 102070, Ref: 1331854C2)$182.00
Center Link Handle - Used on 1954221C3 top link center, this handle will replaces OEM part number 1331863C2. Used on International models: 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, 21206, 21256, 21456, 3388, 3588, 3788, 5088, 5488, 6388, 6588, 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 8288, 8910, 8920, 8930, 8940, 8950, 9310, 9330, 9350, MTX155, MTX165, MTX175, MTX185, MTX200, MX150, MX170, MX180, MX200, MX220, MX240, MX270, MX275, XTX185, XTX200, XTX215 (Item #: 170271, Ref: 1331863C2)$4.98
Latch Spring, Lower - Used with 382192R1, 398373R1, and 398399R1 Latches, this part is used on three point hitches on the following models: 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 8910, 8920, 8930, 8940, 8950, 706, 756, 766, 786, 806, 826, 856, 886, 966, 986, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, 2706, 2756, 2806, 2826, 2856, 3088, 3288, 3388, 3488, 3588, 3688, 3788, 5088, 5288, 5488, 6388, 6588, 6788, 21026, 21206, 21256, 21456. Replaces 382192R1 (Item #: 109644, Ref: 382192R1)$11.30
Latch Spring, Upper - Used with 382192R1, 398373R1, and 398399R1 Latches, this part is used on three point hitches on the following models: 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 8910, 8920, 8930, 8940, 8950, 706, 756, 766, 786, 806, 826, 856, 886, 966, 986, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, 2706, 2756, 2806, 2826, 2856, 3088, 3288, 3388, 3488, 3588, 3688, 3788, 5088, 5288, 5488, 6388, 6588, 6788, 21026, 21206, 21256, 21456. Replaces 382193R1 (Item #: 108835, Ref: 382193R1)$11.30
Lower Adjusting Screw - Measuring 12.125 inches over all length, this Adjusting Screw and 1.250 inch - 7 thread. The threaded portion is 6.268 inches long. This part replaces: 1272852C1, 1272852C91. It is used on HYDRO 186, 1066, 1086, 1466, 1468, 1486, 1566, 1586, 3088, 3288, 3388, 3488, 3588, 3688, 3788, 5088, 5288, 5488, 6388, 6788, 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 7288, 7488, 8910, 8920, 8930, 8940, 8950. This part is used with 108584C1 Upper Adjustment Screw, 149836C4 Leveling Screw Housing, 149838C1 Upper Adjustment Screw, 72877C1 Leveling Screw Housing. (Item #: 108795, Ref: 149837C1)$81.00
Telescoping Lift Arm Latch - For Category II three point hitches, this latch is used on International models: 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 8910, 8920, 8930, 8940, 8950, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, 3088, 3288, 3388, 3488, 3588, 3688, 3788, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 21206, 21256, 21456. Order 382193R1 Upper Spring and 382192R1 Lower Spring if need (sold separately). Replaces 398399R1 (Item #: 109523, Ref: 398399R1)$23.20
Top Link Center - NOTE: This item will not work with standard duty OEM components on models 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 21206, 21256, 21456, 3388, 3588, 3788, 5088, 5288, 5488, 6388, 6588 and 6788. Full assembly 1331854C2 must be used for these applications because of the larger 1.500 inch thread size. This part is compatible with original equipment on models 7110 through 8950. This part replaces 1954221C1, 1954221C2 (Item #: 170260, Ref: 1954221C3)$97.98
Top Link End, Front RH Threads - NOTE: This item will not work with standard duty OEM components on models 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 21206, 21256, 21456, 3388, 3588, 3788, 5088, 5288, 5488, 6388, 6588 and 6788. Full assembly 1331854C2 must be used for these applications because of the larger 1.500 inch thread size. This part is compatible with original equipment on models 7110 through 8950. (Item #: 118323, Ref: 1981986C1)$41.98
Top Link End, Rear LH Threads - NOTE: This item will not work with standard duty OEM components on models 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 21206, 21256, 21456, 3388, 3588, 3788, 5088, 5288, 5488, 6388, 6588 and 6788. Full assembly 1331854C2 must be used for these applications because of the larger 1.500 inch thread size. This part is compatible with original equipment on models 7110 through 8950. (Item #: 118322, Ref: 1282063C2)$199.00
Universal Parts and Accessories Category: Hitch / Drawbar
Center Link Pin - For tractors using a Category 1 3 point hitch. Pin diameter of 3/4 of an inch. Usable length of 3 inches. Overall length of 4 15/32. Head diameter of 7/8 of an inch, with a 1/2 inch hole. Fits many models. Verify dimensions for your specific application. Can be used with DKP14 linch pin. (Item #: 108702, Ref: 957E560)$1.90
Check Chain and Pin Kit - Includes 1 Chain and 2 Clevis with pins and cotters. For most early models, pre-1965, category 1. (Item #: 111334, Ref: CBPN598A)$8.90
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447)$343.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448)$381.00
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416)$429.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417)$429.00
Drawbar, Universal Cat I, 20-1/2 Inch - Universal Category I Drawbar Measures: (A) 1-7/64 inches thick, (B) 2-3/8 inches wide, (C) 20-1/2 inches center to center on lower link pins, (D) 1-15/16 inches from center of pin to edge of body, (E) 2-1/32 inches from body edge to center of first body hole, (F) 3-3/32 inch center to center between holes, (G) 7/8 inch end pin, (H) Five 25/32 inch holes. (Item #: 179615, Ref: S.49123)$60.00
Drawbar, Universal Cat I, 25-1/2 Inch - Universal Category I Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 25-1/2 inches center to center on lower link pins, (D) 1-15/16 inches from center of pin to edge of body, (E) 4-29/64 inches from body edge to center of first body hole, (F) 2-1/8 inch center to center between holes, (G) 7/8 inch end pin, (H) Seven 25/32 inch holes. (Item #: 178799, Ref: S5009)$41.00
Drawbar, Universal Cat I, 29-3/4 Inch - Universal Category I Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 29-3/4 inches center to center on lower link pins, (D) 1-15/16 inches from center of pin to edge of body, (E) 4-1/2 inches from body edge to center of first body hole, (F) 2-1/8 inch center to center between holes, (G) 7/8 inch end pin, (H) Nine 25/32 inch holes. (Item #: 178800, Ref: S128196)$50.00
Drawbar, Universal Cat II, 30-3/4 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 30-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 2-3/8 inches from body edge to center of first body hole, (F) 2-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Eleven 25/32 inch holes. (Item #: 103176, Ref: S126)$58.00
Drawbar, Universal Cat II, 30-3/4 Inch - Universal Category II Drawbar Measures: (A) 1-1/4 inches thick, (B) 3 inches wide, (C) 30-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 3 inches from body edge to center of first body hole, (F) 2 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Eleven 3/4 inch holes. (Item #: 103176, Ref: S60155)$58.00
Drawbar, Universal Cat II, 36-1/4 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 3-1/8 inches wide, (C) 36-1/4 inches center to center on lower link pins, (D) 2 inches from center of pin to edge of body, (E) 3-35/64 inches from body edge to center of first body hole, (F) 3-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Nine 1-19/64 inch holes. (Item #: 179623, Ref: S15134)$139.00
Drawbar, Universal Cat II, 36-29/32 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 36-29/32 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 3-9/16 inches from body edge to center of first body hole, (F) 3-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Nine 1 inch holes. (Item #: 179670, Ref: S3394)$100.00
Drawbar, Universal Cat II, 36-3/4 Inch - Universal Category II Drawbar Measures: (A) 1-1/4 inches thick, (B) 3 inches wide, (C) 36-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 3-7/8 inches from body edge to center of first body hole, (F) 2 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Thirteen 3/4 inch holes. (Item #: 103177, Ref: S60156)$95.30
Drawbar, Universal Cat II, 39-3/8 Inch - Drawbar, Universal Cat II, 39-3/8 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 39-3/8 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 7-7/8 inches from body edge to center of first body hole, (F) 3-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Seven 1-1/8 inch holes. (Item #: 179583, Ref: S15081)$105.00
Drawbar, Universal Cat III, 42-3/4 Inch - Drawbar, Universal Cat III, 42-3/4 Inch - Universal Category III Drawbar Measures: (A) 1-49/64 inches thick, (B) 3-1/2 inches wide, (C) 42-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 5-61/64 inches from body edge to center of first body hole, (F) 4-21/64 inch center to center between holes, (G) 1-27/64 inch end pin, (H) Seven 1-1/4 inch holes. (Item #: 180531, Ref: S29139)$300.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X)$11.50
Leveling Assembly - Universal Economy Leveling Assembly. 1-5/16" body of high strength tubing, thread size, 7/8" fine thread-study clevis at each end with 5/8" pin holes. May be used right or left. Can Replace NCA577A and Fork. 18 inches closed, 28 inches open. (Item #: 154104, Ref: LB152)$33.00
Lift Arm Bushing - This Bushing is for using Category I Implements with Category II Lower Lift Arms. It has a 7/8 Inside Diameter, and 1-1/8 Outside Diameter and is 1-3/4 Inches long. Replaces B500192, 87299215, 87760407, EC0NG992AA, 150-821, BUSH04, 22BCO006, 477RB, BO821, 2430351, B821, B2008, 351, 00351, C7NNG992A, 81819374 (Item #: 108626, Ref: BUSH04)$2.70
Linch Pins, Pack of 2 - Pin diameter 1/4 inch, useable length 1 1/4 inch. Cold Forged. Enter 1 for package of 10. (Item #: 153789, Ref: DKP14)$1.20
Linch Pins, Pack of 2 - Package of 2 linch pins, 7/16 inch diameter pin x 1-3/4 inch usable length, 1-5/8 inch diameter ring. Cold Forged. Enter 1 for package of 2. (Item #: 153792, Ref: DKLP91)$1.30
Linch Pins, Pack of 2 - Linch Pins. 3/16 inch outside diameter pin x 1-1/4 inches Long. (Item #: 153788, Ref: DKP316)$1.10
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 490mm (19 15/16 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches). Verify that the measurements will meet the requirements of your application. (Item #: 185049, Ref: 159332)$44.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 21.5 Inches Center to Center (A), Thickness: 5/8 inches, Width 2 9/16 inches, 7 1/4 Inches from center of ball joint for first hole (B), 9 1/4 inches from center of ball to second hole (C). Verify that the measurements will meet the requirements of your application. (Item #: 103203, Ref: 159324)$40.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 595mm (23-7/16 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), Three holes located 13-3/4 inches, 12 inches and 8-1/2 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 185732, Ref: 159326)$74.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 645mm (25 13/32 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), Three holes located 14-3/4 inches, 13 inches and 8-1/2 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 184428, Ref: 159328)$60.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 700mm (27 9/16 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), Three holes located 16-1/4 inches, 13 inches and 6-1/4 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 103206, Ref: 159330)$63.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 750mm (29 1/2 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), One hole located 6 1/4 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 103207, Ref: 159322)$65.00
Mower Deck Height Stabilizer Kit - Fits all category 1 tractors. Chain length is 40 inches. Maintains consistent mower height and eliminates need for stabilizer bars. Contains two top brackets and two lower brackets with chain. (Item #: 103201, Ref: MHSK1)$42.00
Quick Hitch A-Frame Design - Makes for easier implement attachment, by use of self-aligning steel roller. System self-aligns as tractor�s 3-point hitch is raised. This is a CE Approved, Cat I. 2645 pound capacity. For implement side adapter, see part number S23465. Additional $200.00 shipping due to weight. (Item #: 179003, Ref: S110168)$358.00
Quick Hitch A-Frame Implement Adapter - Used with S110168 quick hitch, this is a weld on bracket. The load capacity is3306 pounds. (Item #: 179380, Ref: S23465)$106.00
Quick Hitch, Category I - Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed. This part ships via truck freight. Please call for pricing and ordering. (Item #: 180731, Ref: HF141101)$337.00
Stabilizer Assembly - This Stabilizer Assembly measures 14 inches minimum to 17.5 max. It has 7/8 inch pin holes and 12 degree bend on the link side. This part is sold a a universal part. Verify measurements before ordering. (Item #: 179605, Ref: 343437X1)$22.60
Stabilizer Chain - This Stabilizer Chain is sold as a universal part. Verify measurements before ordering. It is Adjustable 11.75 inches to 13.5 inches with a 3.5 inch body. 7/16 inch Pin Diameter. (Item #: 173628, Ref: 159350)$27.30
Stabilizer Chains, Set - 1 SET OF 2 stabilizers for ford tractors having an extra link which allows easy attachment to large and small model tractors by uncoupling the clevis and pin and moving up or down one link of the stabilizer accordingly. (Item #: 174066, Ref: SK102CH)$64.00
Stabilizer Link - This Stabilizer Link is used on Compact Tractors. It adjusts from 15.5 inches to 19.5 inches. The Link Side is 0.79 inches. The Eyelet Side is 0.90 inches. This part is sold as a universal part. Verify measurements before ordering. (Item #: 179606, Ref: VPL3232)$28.00
Top Link - Economy Top Link, 16 inch body. Category 1, 3/4 inch balls. Adjusts 20.5 to 29 inches overall. Dichromate plated center body. OEM JSA5050 (Item #: 184512, Ref: 30533E91)$26.90
Universal Drawbar Lock - For CAT I drawbars only (drawbars that are 1 inch thick x 2-1/2 inch width) . Prevents drawbar from rotating. (Item #: 178107, Ref: 49A29)$26.60
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2)$37.00
Call 800-853-2651 to Order Or Click the "Add to Cart" Button
YESTERDAY's TRACTORS
has been a leading tractor parts supplier on
the internet since 1995. Join thousands of happy customers
who have purchased parts and more for their antique tractor from us!
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
