Axle Knee Left Hand - Used on the following tractors with straight front axles: 685, 695, 884, 895, Hydro 84, 684, 784, 885. For Left Hand order 108811. Replaces 3116436R91 (Item #: 108810)$425.98
Axle Knee Right Hand - Used on the following tractors with straight front axles: 685, 695, 884, 895, Hydro 84, 684, 784, 885. For Left Hand order 108810. Replaces 3116437R91 (Item #: 108811)$280.98
Front Axle Bolt - Used to secure front axle knees, this bolt measures 4-3/4 inches overall, 4 inches to the shoulder and has 3/4-16 UNF RH Thread. If nuts are needed, order 116643. Replaces part number 405584R1 (Item #: 124558)$9.90
Front Axle Nut - Used with part number 124558 to secure axle knees, this nut is 3/4 inch -16 UNF thread. Replaces 405576R1 (Item #: 116643)$2.40
Front Axle Pivot Shaft - This Front Axle Pivot Shaft is 13.250 inches Long. It is used on 2400, 2500A, 380B, H84, 385, 395, 454, 464, 484, 485, 584, 585, 595, 674, 684, 685, 695, 784, 884, 885, 895, CX100, CX50, CX60, CX70, CX80, CX90. Replaces 405564R91, 405577R1, 405577R2, 527790R91, 538688R91, 539128R1 (Item #: 124722, Ref: 539128R1)$218.00
Front Bolster - For International / Farmall tractor models Hydro 84, 248, 268, 385, 484, 485, 584, 684, 685, 784, 884, 885, Replaces International OEM number 3121169R4, (Item #: 124586)$1379.01
Power Steering Clevis End - This Power Steering Clevis End has a pin hole of 20 MM (.787 inches) and fits cylinder 188842A1. For tractor models 385, 454, 464, 474, 485, 574, 584, 585, 674, 684, 685, 784, 884, 885, 2400, 2500. Replaces 549670R2. (Item #: 113280, Ref: 3125306R1)$43.00
Power Steering Cylinder - Complete cylinder with 1 inch diameter shaft. Includes 549670R2 Clevis. For tractor models 385, 454, 464, 474, 485, 574, 584, 585, 674, 684, 685, 784, 884, 885, 2400, 2500. Replaces 400587R1, 549667R91, 549667R93, 188842A1, 549667R92, 84336125. VERIFY PART NUMBER TO ENSURE CORRECT REPLACEMENT. (Item #: 104583, Ref: 188842A1)$280.00
Power Steering Cylinder End - From the center of the ball joint to the end of the tube, this power steering cylinder end measures 3.250 inches. It has M20 X 1.5 RH Thread. Used on 4WD front ends on 1046, 1246, 258, 268, 278, 584, 585, 585XL, 644, 684, 685, 685XL, 743, 743XL, 744, 744S, 745S, 745XL, 784, 785, 785XL, 844, 844S, 844XL, 856, 856XL, 884, 885, 885XL, 946, Hydro 84. Replaces 3146035R92, 3146035R1, 3146035R95, 3146035R91, 3146035R94 (Item #: 124614, Ref: 3146035R95)$105.00
Power Steering Cylinder Rod - Used on UK built International 2 wheel drive tractors, this part replaces 549668R1, 549668R2, 188851A1, 549668R3, 188854A1. Used on 238, 248, 258, 268, 288, 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 884, 885, 885XL, 895, 895XL, 995, 995XL, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84, Hydro 86, MX100C, MX80C, MX90C (Item #: 182916, Ref: 549668R1)$332.00
No Picture
Ring Gear and Pinion Set, Used - For International tractor models Hydro 84, 268, 278, 584, 674, 684, 685, 784, 785, 884, 885, Replaces International OEM nos 65779C1, Teeth: 11/ 52, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 434313)$540.01
Seal Kit, Power Steering Cylinder - For 2 wheel drive models 454, 464, 574, 674, 484, 584, 684, 784, 884, 385, 485, 585, 685, 885, 595, 695, 995, 2400, C50, C60, C80, C90, C100, 4210, 4230, 4240. VERIFY PART NUMBER TO ENSURE CORRECT REPLACEMENT. (Item #: 115098, Ref: 55355C91)$41.00
Spindle Bushing - Fits 1.667 inch diameter spindles replaces 376099R1. For use with A-71785HD and OEM spindle. (Item #: 102175, Ref: 358958R2)$9.00
Spindle Nut - Fits on Front Spindles. Castle Nut 3/4 inch x 16 UNF. P2060, VLG3307, 351129S, 353928X1, 354573S36, 387930S36, 646060M1, 83416613, 83900513, 83910701, 880284M1, 9073, 98A750N, 129-290, 88886, 427639, 88886 (Item #: 156038, Ref: 387930S36)$1.10
Spindle Seal MFWD - On Mechanical Front Wheel Drive tractors, the seal (o-ring) goes between the axle housing and the spindle. It is used on many ZF Axles. Replaces OEM part numbers 81296C1, 83946009, 8603728, 3147244R1, ZP0634303409, 1390411028, 81296C1, 1964258C1, 3147244R1 (Item #: 124682, Ref: 83946009)$0.50
Spindle, RH/LH - This spindle measures A= 9.50 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 684, 685, 685XL, 695, 695XL, 784, 884, 885, 885XL, 895, 895XL, Hydro 84. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 104328, Ref: 3125872R91)$187.00
Spindle, RH/LH - This spindle measures A= 8.312 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 268, 278, 3230, 4210, 4230, 4240, 584, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, 995, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 100846, Ref: 3121270R91)$174.00
Spindle, RH/LH - This spindle measures A= 15.250 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models (674, 684, 884, Hydro 84 all with straight axle). The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 100851, Ref: 67526C91)$248.00
Spindle, RH/LH - This spindle measures A= 11.250 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 268, 278, 3230, 4210, 4240, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 104329, Ref: 3121261R91)$205.00
Steering Arm Assembly - For International / Farmall tractor models Hydro 84, 258, 268, 278, 385, 454, 484, 485, 574, 584, 585, 674, 684, 685, 784, 785, 884, 885, 2400, 2500, Replaces International OEM number 67499C91, (Item #: 158746)$560.00
Steering Arm Assembly, Used - For International tractor models Hydro 84, 258, 268, 278, 385, 454, 484, 485, 574, 584, 585, 674, 684, 685, 784, 785, 884, 885, 2400, 2500, Replaces International OEM number 67499C91, For a new version of this item use Item #: 158746, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 457198)$444.00
Steering Arm, Left Hand - This is a left hand steering arm use on adjustable front axel. 52 inch to 77 inch Used on IH models 268, 278, 3230, 4210, 4230, 4240, 584 Indust/Const, 585, 684, 685, 695, 784, 785, 884, 885, 895, 995, CX100, CX70, CX80, CX90, Hydro 84 Replaces 3121263R1 (Item #: 124740, Ref: 3121263R1)$371.00
Steering Arm, Right Hand - This Right Hand Steering Arm is used on 268, 278, 3230, 4210, 4230, 4240, 585, 595, 684, 685, 695, 784, 785, 884, 885, 895, 995, CX100, CX70, CX80, CX90, Hydro 84. It replaces 3121264R1 (Item #: 124741, Ref: 3121264R1)$214.98
Steering Motor, Hydrostatic - No relief valve. For tractor models (385, 484, 485, 585 up to serial number 18001), 684, 685, 784, 884, 885, 380B. (Item #: 104262, Ref: 67698C93)$449.00
Steering Shaft, Hydrostatic Motor - 9 inches overall length. For tractor models 385, 484, 485, 584, (585 less cab up to serial number 18001 with heavy duty front axle), (684 with heavy duty front cast axle), (685, 885 less cab), 784, 884, 380B. (Item #: 153931, Ref: 3121187R91)$72.00
Steering Wheel - 16 inch diameter. Mounts on 13/16 inch (36 spline) shaft. For the following tractors WITH POWER STEERING : HYDRO 70, HYDRO 84, HYDRO 86, HYDRO 100, HYDRO 186, 404, 424, 444, 454, 464, 484, 504, 544, 574, 584, 606, 656, 664, 666, 674, 684, 686, 706, 756, 766, 784, 786, 806, 826, 856, 884, 886, 966, 986, 1026, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, 2400, 2500, 3088, 3220, 3230, 3288, 3388, 3588, 3688, 3788, 4386, 4586, 4786, 5088, 5288, 5488, 6388, 6588, 6788. Replaces IHS542. Cap is available separately as part number 68837C3. (Item #: 101432, Ref: 385156R1)$47.00
Thrust Bearing - For tractor models 684, 685, 685XL, 686, 695, 695XL, 706, 756, 766, 782, 784, 786, 806, 826, 856, 86 SERIES with AXLE PIVOT BALL, NOT PIN), 88 SERIES EARLY with AXLE PIVOT BALL, NOT PIN), 884, 885, 885XL, 886, 895, 895XL, 966, 986, H, HV, HYDRO 100, HYDRO 186, HYDRO 3488, HYDRO 70, HYDRO 84, HYDRO 86, M, MTA, Super H, Super HV, Super M. 1.755 inches inside diameter, 2.685 inches outside diameter, 0.694 inches wide. Replaces 185106C1, 185106C91, 357349R91, 361034R91, 369131R91, 387231R91, 405831R91, 527295R91, 844398R91 (Item #: 102174, Ref: 185106C1)$13.40
Tie Rod - Tie rod end, outer, recess for set screw (7) at bottom, 15 inch to center of post, .812 inch rod diameter. Used on tie rod assemblies with set screw recess outer end and threaded inner end. For straight adjustable axles 52 to 80. For tractor models Hydro 84, 385, 395, 484, 485, 495, 584 except utility For 385, 395, 484, 485, 495, 584, 595, 684, 685, 695, 784, 884, 885, 895, 995, HYDRO 84. Replaces 3116406R3, 1332805C1, 3125171R1, 1332805C2. (Item #: 100865, Ref: 3116406R3)$32.00
Tie Rod - Tie rod end, inner, right hand thread, 3-7/8 inch to center of post. 0.875 Inch x 16 RH Thread. Used on tierod assemblies with set screw recess outer end and threaded inner end. For straight adjustable axles 52 to 80 on tractors: Hydro 84, 385, 395, 484, 485, 495, 584, 684, 784, 884. 52 to 82 on tractor For 385, 395, 484, 485, 495, 584, 595, 684, 685, 695, 784, 884, 885, 895, 995, HYDRO 84. (Item #: 100864, Ref: 3116407R3)$15.60
Tie Rod - Tie rod end, outer, recess for set screw (6), 14-1/8 inch to center of post. Used on tie rod assemblies with set screw recess outer end and threaded inner end. For straight adjustable axles 52 to 77 on tractors: Hydro 84, 595, 684, 685, 695, 784. 884, 885, 895, 995.52 For 584, 595, 684, 685, 695, 784, 884, 885, 895, 995, HYDRO 84 (Item #: 100872, Ref: 3125171R2)$35.00
Tie Rod - Tie rod end, outer, notched {7}, 15 inches to center of post, .750 inch diameter. For tractor models 2400A, 2500A, 385, 484, 485, 574, 584, 674, 684, 784, 884, HYDRO 84. (Item #: 100871, Ref: 65079C91)$31.00
Tie Rod - A= 4.16 inch, B= M30 x 1.5 inch inside diameter right hand thread. For tractor models 258, 268, 278, 584, 585, 684, 784, 785, 884, 885, Hydro 84 all with 4WD. (Item #: 124763, Ref: 1502269C2)$66.98
Tie Rod Assembly - This Tie Rod Assembly is used on Adjustable Straight Axles (52 Inches to 82 Inches Tread Width). It Replaces 3125171R2, 3125171R3, 1332805C2, 3116406R3, 3116406R4, 3116406R5, 3116321R93, 1538016C1. (Item #: 156878, Ref: 1538016C1)$153.37
Tie Rod Assembly, Complete - Due To Multiple OEM Styles, Individual Pieces May Not Fit Models Listed, But Can Use Assembly As A Replacement. Assembly Consist Of: (1) 65079C91, (1) 527658R91, (1) 67529C1, (1) 390686R1, (1) 43747D. 65079C91: Stud Taper= .606 To .700 inches, 527658R91: Stud Taper= .606 To .700 inches. Used on 574, 2400A Straight Front Axle serial number 100006 and up, 2500A Straight Front Axle serial number 100004 and up, 385 Straight Front Axle, 454 Straight Front Axle serial number 100006 and up, 484, 485, 495 Straight Front Axle, 584 Adjustable Straight Front Axle, 585, 595 Adjustable Straight Front Axle, 674 Straight Front Axle, 684, 695 Adjustable Straight Front Axle, 784, 884, 885 below serial number 3083. (Item #: 124766, Ref: 223326)$134.00
Tie Rod Clamp - Used on Farmall / IH models, this tie rod clamp fits 574, AV, AV1, A1, CUB, SUPER A, 100, 130, 140, 200, 230, 240, 2400, 248, 2500, 2504, 258, 3230, 340, 385, 404, 4210, 4230, 4240, 454, 474, 484, 485, 504, 584, 585, 595, 674, 684, 685, 695, 784, 884, 885, 995 (Item #: 104368, Ref: 43747D)$17.70
Tie Rod End - Dimension A= 4.060 inch, B= 0.812 inch (16 UN right hand thread). Fits the following tractors with ADJUSTABLE CAST I-BEAM FRONT AXLE: Hydro 84, 454, 484, 485, 495, 544, 574, 585, 595, 595XL, 656, 684, 685, 695.YTO-379327R91_. (Item #: 104406, Ref: 379327R91_)$30.00
Tie Rod End - Used on the following with non-adjusting Cast I Beam front axles: 574, 2400A, 2500A, 2544, 2656, 380B, HYDRO 84, 454, 484, 485, 495, 544, 584, 585, 595, 595XL, 656, 684, 685, 685XL, 784, 884, 885, 885XL, 895, 895XL. A= 4.00 inch, B= 13/16 inch, 16 left hand thread. Replaces 379326R91 (Item #: 104593, Ref: C5NN3A300C)$24.80
Tie Rod Tube - This Tie Rod Tube is 16.187 inches long and with 7/8 inch 16 thread. It replaces 3116408R1. (Item #: 104409, Ref: 3116408R1)$39.00
Tie Rod Tube - Used with straight axles only, this tie rod tube measures 16.190 inches long, 1 inch outside diameter. Used on 574, 2400A serial number 100000 and up, 2500A serial number 100000 and up, 385, 454 serial number 100000 and up, 484, 485, 584, 585, 674, 684, 784, 884. (Item #: 104408, Ref: 67529C1)$44.00
Universal Joint - The measurements on this Universal Joint are 27mm cup diameter and 82mm across. Side greaser included. This Universal Joint is used on Carraro 4WD front axles. Replaces OEM numbers CAR96867, CAR116859, 3230277R1, 3216550R91, 137700420834, 1967554C1, 84512487, NH80715, 9961774, 9962244, 87760752, K965331, CAR041121, CAR116859, 83934724, 81927841, ZP1927504, ZP1927841, 3230277R1, 84512487, 83957857, AL32885, 137700000000, 3475808M91, 3475808M1, 3427352M91, 1895699M1 (Item #: 156129, Ref: CAR96867)$43.00
Universal Parts and Accessories Category: Steering
Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn Power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003)$410.00
Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: 133205R91 (Item #: 111126, Ref: AE33538A)$13.30
Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417)$49.00
Steering Wheel Spinner, Bare Aluminum - Comes with mounting hardware. (Item #: 108667, Ref: R3275)$8.00
Steering Wheel Spinner, Blue - Comes with mounting hardware. (Item #: 108664, Ref: R3279)$10.10
Steering Wheel Spinner, Green - Comes with mounting hardware. (Item #: 108666, Ref: R3278)$13.40
Steering Wheel Spinner, Orange - Comes with mounting hardware. (Item #: 108660, Ref: R6323)$16.10
Steering Wheel Spinner, Red - Comes with mounting hardware. (Item #: 108663, Ref: R3277)$8.90
Steering Wheel Spinner, Yellow - Comes with mounting hardware. (Item #: 108665, Ref: R3280)$8.00
No Picture
Wheel Spinner- Black - Wheel Spinner, black knob, universal. WSV124B (Item #: 108662, Ref: R3276)$9.60
Call 800-853-2651 to Order Or Click the "Add to Cart" Button
YESTERDAY's TRACTORS
has been a leading tractor parts supplier on
the internet since 1995. Join thousands of happy customers
who have purchased parts and more for their antique tractor from us!
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
