International Harvester / Farmall Super MD Parts

[Categories]   [All Super MD Parts]   [All Farmall Models]  

Axle Center Tube - For all models listed with factory IH wide front with tie rods behind center tube: H, Hydro 70, M, MD, MTA, Super H, Super M, Super MD, 1026, 1206, 1256, 300, 350, 400, 450, 460, 544, 560, 656, 666, 706, 756, 806, 826, 856 Axle Center Tube with bushings (48841D) is 42 1/2 inches long and 4 1/2 inches in diameter. Replaces: 358976R31, 383926R21, Bushing: 48841D (Item #: 109489, Ref: 358976R31) $450.00
Axle Pivot Pin Bushing - This Bushing Measures 1.245 inches inside diameter, 1.375 inches outside diameter, 1.486 inches long. Sold individually. This bushing has a superior dimpled brass inner design to retain grease. No need for an external grease hole. Note: Must be honed or reamed to size when installed. Used on the following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle: 1026, 1256, 400, 450, 660, 666, 300, 350, 460, 544, 560, 656, 706, 756, 806, 826, 856, H, Hydro 70, M, MD, MTA, Super H, Super M, Super MD, Super MDTA, Super MTA, W400, W450. Replaces 48841D (Item #: 109669, Ref: 48841D) $13.50
Oil Seal - Oil seal for bearing kit FW113FS. External Lip, Spring Loaded, Closed Case Seal, 2.786 in od, 1.75 in id, and .294 in wide. For Tractors H, Super H, M and MD, 4, Super W4, 300, 350. For 2606, 300, 350, 4, 460, 504, 606, H, M, MD, Super H, Super M, Super MD, Super W4. Check measurements. (Item #: 110745, Ref: 48539DA) $11.00
Stay Rod Assembly - Stay Rod Assembly "Wishbone" fits wide front end tractors. For tractor models 1206, 1256, 300, 350, 400, 450, 460, 544, 560, 656, 660, 666, 686, 706, 756, 806, 826, 856, H, Hydro 70, M, Super H, Super M, Super MD. Replaces 10546D, 360405R11 VERIFY PART NUMBER IN PARTS MANUAL FOR YOUR TRACTOR. (Item #: 167990, Ref: 360405R11) $500.00
Steering Shaft Cross and Bearing (U-Joint) - Tighten up your steering with a new Universal Joint. This part measures 2.305 inches across cap to cap, with a 0.968 inch cap diameter. Some models use more than one, sold individually. Some models used different sizes, verify measurements. Replaces OEM numbers 10P715, 1KAR758, 224890, 350254R91, 357439R91, 363313R91, 363321R91, 52977DAX, 70224890, 836514M91, 841193M92, A20435, A20684, A30408, A30425, A30428, A30435, VTA3227, Z862 (Item #: 115351, Ref: 70224890) $11.60
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00
Steering Worm Gear, Sector - 32 teeth. For tractor models 400, 450, M, Super M, Super MTA. The style of this gear is full circle. This gear has 32 teeth. It can also replace a 19 tooth sector (1/2 inch moon style). Replaces: 50037DA, 50037DB, 704168R1. (Item #: 124445, Ref: 50037DB) $164.00
Steering Worm Shaft Bearing - This Steering Worm Shaft Bearing has a 0.984 inch inside diameter, a 2.047 inch outside diameter and a 0.590 inch width. Fits B, BM, BN, C, H, HV, M, MD, MDV, MTA, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDV-TA, Super MTA, Super MV, Super MVTA, 200, 230, 400, 450, Super MTA, (424, 444 used as a steering worm shaft bearing; without power steering), 240, 300, 340, 350, 404, 504, 240, 404. Replaces: 1271857C91, 1273146C91, 210041, 43357D, 69696D, 741-0360, 741-3037, 941-3037, ST225, ST225AT, ST225B, ST225BT, ST225Y, ST678. (Item #: 178091, Ref: ST225B) $9.30
Steering Worm Shaft Oil Seal - This Steering Worm Shaft Oil Seal measures 1.000 inch inside diameter, 1.503 inch outside diameter, 0.250 inch wide. Fits B, BN, C, H, HV, M, MD, MDV, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDV-TA, Super MV, Super MVTA, 200, 230, 240, 400, 450, MTA diesel, 300, 340, 350. Replaces: 359042R91, 359257R91, 364468R91, 43800D, 43800DA, 488561R91. (Item #: 122678, Ref: 43800D) $5.50
Tie Rod Assembly - Using this tie rod assembly for the models listed will take modification, but it is the only one available for factory original row crop models: H, M, MD, MTA, Super H, Super M, Super MD, Sure MTA, 300, 350, 400, 450. This tie rod assembly tapered ball stud measures 0.675 inch to 0.762 inch at the widest point of the taper shaft, with 5/8-18 thread. The tie rod is adjustable to a maximum of 34-1/4 inches and a minimum of 20-7/8 inches. Fits factory INTERNATIONAL wide front axles only (with tierods behind the center axle.) Will NOT fit Swartz, Norden, Speeco, or other aftermarket wide front axles. To make this assembly work for these applications, the center tube must be shortened about an inch. We do not have instructions for doing this modification. This part can not be returned if you make modifications to the tube. Contains the following items: 359984R93 Tie Rod- Outer, 359986R1 Clamp, 374062R1 Jam Nut, 383917R1 Tube, 384006R92 Tie Rod- Inner. (Item #: 100869, Ref: 223313) $85.00
Universal Parts and Accessories Category: Steering
Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn Power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003) $398.00
Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: 133205R91 (Item #: 111126, Ref: AE33538A) $12.60
Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $48.20
Steering Wheel Spinner, Bare Aluminum - Comes with mounting hardware. (Item #: 108667, Ref: R3275) $8.00
Steering Wheel Spinner, Blue - Comes with mounting hardware. (Item #: 108664, Ref: R3279) $8.60
Steering Wheel Spinner, Green - Comes with mounting hardware. (Item #: 108666, Ref: R3278) $13.40
Steering Wheel Spinner, Orange - Comes with mounting hardware. (Item #: 108660, Ref: R6323) $8.50
Steering Wheel Spinner, Red - Comes with mounting hardware. (Item #: 108663, Ref: R3277) $8.90
Steering Wheel Spinner, Yellow - Comes with mounting hardware. (Item #: 108665, Ref: R3280) $8.24
No Picture Wheel Spinner- Black - Wheel Spinner, black knob, universal. WSV124B (Item #: 108662, Ref: R3276) $9.60