FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Massey Ferguson 2500 Parts

Category: Hydraulic System

[Categories] [All MF2500 Parts] [All Massey Ferguson Models]

Dipstick - Hydraulic oil level indicator measures overall length of 7 3/8 inches and 5 inches from the stop down. It is used on tractors models: FE35, Super 90, TE20, TEA20, TO20, TO30, TO35, 135, 150, 165, 175, 203, 204, 230, 231, 235, 245, 253, 255, 265, 275, 360, 362, 383, 65, 85, 88, 202, 205, 302, 2135, 2500, 35, MF 50, MH 50. Replaces 180366M1, 193400M1, 514184M1. (Item #: 111829, Ref: 193400M1) $11.00

Draft Control Boot - Draft Spring Rubber Boot. Fits Multiple Massey Ferguson Models. Replaces 1660439M1, 887654M1, 887654M2. (Item #: 169245, Ref: 887654M1) $3.10

Hydraulic Gear Pump - For (MF30, MF40, 30, 40) (100, 200, 225, 235, 32, 32A, 34, 34A, 34B ALL LOADER) (212, 52, 44 ALL BACKHOE) (2200, 2500, 4500, 5400H, 6500, 6500H, 6800 ALL FORKLIFT) (2244, 400C ALL CRAWLER) (100, 200, 225, 235, 32, 32A, 34, 34A, 34B ALL LOADER) (212, 52, 54 ALL BACKHOE) (2200, 2500, 4500, 6500, 6500H, 6800, 6800H ALL FORKLIFT) (2244, 400C ALL CRAWLER). Hydraulic Gear Pump. Note: Includes adaptor. Ports are located on side of rear housing. CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: left hand, PORT SIZE INLET: 1-5/8 inch -12 ORB, PORT SIZE OUTLET: 1-5/16 inch -12 ORB, MOUNTING: 2 bolt SAE "B", CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIA: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: left hand, MOUNTING: 2 bolt SAE "B", INLET: 1-5/8 inch -12 ORB, OUTLET: 1-5/16 inch -12 ORB. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inches and Maximum is 6 7/8 inches. (Item #: 127269, Ref: 7702425-29Z) $760.00

Hydraulic Pump - Hydraulic Pump, front mount, for backhoes, crawlers, forklifts and loaders. 7/8 inch outside diameter, 13 spline, 21.5 GPM, 2000 rpm. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inch. Maximum is 6 7/8 inch. For 30, 32, 34A, 34B, 40, 52, 54, 100, 200, 212, 225, 235, 400C, 2200, 2244, 2500, 4500, 6500. Hydraulic Pump. H10190RF210RM adapter included. (Item #: 127269, Ref: 2750128M91) $760.00

Hydraulic Pump Support Peg - This hydraulic pump support peg has a step (shoulder) on the pin. The diameter steps from 9/16 inches to 7/16 inches. If you need a straight pin peg, use part number 180905M1. If you need a gasket order part number 180904M1, sold separately. Replaces 898643M1. (Item #: 173297, Ref: 898643M1) $11.20

Hydraulic Pump Support Pin Gasket - This hydraulic pump support pin gasket is used with 180905M1 and 898643M1 hydraulic pump support pins. It replaces 180904M2, 180904M1. (Item #: 167222, Ref: 180904M1) $0.60

Lift Cover Gasket - For tractor models 135, 135 UK, 150, 165, 165 UK, 175, 175 UK, 178, 180, 20, 202, 203, 204, 205, 20C, 20E, 20F, 2135, 2200, (230, 245, 265, 275 serial number 9A349239), 235, 2500, 255, 256, 282, 30, 302, 304, 30B, 30H, 31, 3165, 35, 40, 40B, 4500, 50, 50A, 50C, 50F, 60, 65, 6500, 6500H, F40, FE35, TO35. (Item #: 112052, Ref: 886549M2) $1.70

Universal Parts and Accessories
Category: Hydraulic System

Clamp, Double Break-Away, Hydraulic - For use with S20-4 and S40-4 Couplers. Quik-Cover Assembly HV4957 fits this Clamp. (Item #: 112480, Ref: S42-4) $29.95

Coupler Flange - Optional drive flange for L601-9; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch spacing. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b. (Item #: 108772, Ref: L36-6) $119.41

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $25.70

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $14.70

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 36 inch - Universal. 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends, 36" overall length. Replaces OEM 407436R1. (Item #: 118260, Ref: H42-2M-36) $15.20

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199) $21.10

Hydraulic Pump Mounting Bracket - This Hydraulic Pump Mounting Bracket is used for front mounted hydraulic pumps often used with loaders. For use with SAE A 2 bolt flange type pumps. Has 2 tapped mount holes 3/8 inch diameter, 4-3/16 inch center to center. Also 2 foot mount holes 3/8 inch diameter, 5 inch center to center. Center pilot hole 3-1/4 inch diameter. Fits L827-10X-LB, 40P018LAJSA and 195453 pumps. May fit other pumps. Verify measurements before ordering. (Item #: 184547, Ref: 33020-1) $376.00

Hydraulic Pump, Front Mounted - This Hydraulic Pump is used with various loader configurations. 14 GPM and 2, 000 RPM. 3/4 inch round shaft with key way. Left hand Rotation. Inlet ORB 1-5/16 inch. Outlet ORB 1-1/16 inch. SAE A Mounting. Bolt holes are 3/8 inch, 4 3/16 inch center to center. Replaces 192504, 195453. (Item #: 182701, Ref: 40P018LAJSA) $662.00

Hydraulic Selector, isolator assembly - For tractors without individual external hydraulic systems. Three position spool, forward position allows one-way (push) for single acting cylinder. Center position allows operation of the 3-point arms and the rear position will feed power to a 4 way control valve for two way (push-pull) operation of double acting cylinder. Fits all MF tractors where 182373M1 lift cover is used. Replace MF cover plate, adds 2 I/O ports 3/8 inch NPT. (Item #: 185644, Ref: TS300) $148.00

Hydraulic Valve Kit, External, Single Spool - Converts tractor for operation of cylinders on pull type implements, front loaders, hydraulic motors, or other optional hydraulics. Single spool, double acting control valve mounts conveniently on flat or shell fenders. Selector/isolator allows operation of single or double acting cylinders. Mounting hardware and instructions included. Kit contains single spool, double acting control valve, isolator valve, valve couplers, clamp hoses, adaptors, hardware and instructions. For tractor models TO35 and later where 182373M1 lift cover plate is accessible. (Item #: 178324, Ref: TS3200M) $907.00

Hydraulic Valve Manifold - This 3 Spool Valve allows operator to use auxiliary hydraulics at the same time without valve switching. Some tractors may need slight modification on seat. Includes 2 elbows. Models from 1960 and later years. (Item #: 173361, Ref: 19833A92) $1109.01

LBP Coupler Center - This LBP Coupler Center Member measures (A) 3-5/8 inch diameter (B) four 5/16 inch holes, 2-1/4 inch spacing. Replaces 1753729M91. (Item #: 178931, Ref: 192169) $71.00

Moreflex Series 352 Coupler Drive Flange - Coupler for Hydraulic pump drive shaft. 13 spline for 7/8 inch diameter shaft. 5/16 inch diameter bolt holes, 2-1/4 inch on center. For 352. (Item #: 112243, Ref: L78-13) $23.98

PTO Mounted Hydraulic Pump - For 540 RPM 6 spline 1 3/8 Shaft. 21 GPM, 2000 Max PSI. Mounts on shaft. Straight thru design allows normal PTO use with extension shaft. Has two outlet ports. Inlet 1 5/16 - 12 ORB. Outlets 1 1/16 - 12 ORB. Recommended hose sizes 1 1/4 inlet, 3/4 outlet. (Item #: 120040, Ref: HC-PTO-1A) $1307.44

Universal Pressure Gauge, Hydraulic - 300lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglas crystal. 1/4 NPT male brass fitting. (Item #: 184977, Ref: GG300) $11.80

Universal Pressure Gauge, Hydraulic - 3000 Lb. Gauge. Glycerin Filled. Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Plexiglass crystal. 1/4 inch NPT male brass fitting. (Item #: 178343, Ref: GG3000) $12.30

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.60

Universal Pressure Gauge, Hydraulic - 600 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172337, Ref: GG600) $14.90

Universal Pressure Gauge, Hydraulic - 400 lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel Silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglas Crystal. 1/4 NPT male brass fitting. (Item #: 178202, Ref: GG400) $8.98

No
Picture
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.60

Valve - Valve for TS3200M. Single spool, 4-way, 3-position, spring loaded to neutral. No relief valve, no power beyond option. In and out ports 3/4 inch, work ports 1/2 inch NPT. (Item #: 183771, Ref: TS200BA) $313.00

Call 800-853-2651 to Order
Or Click the "Add to Cart" Button

Category: Hydraulic System

[Categories] [All MF2500 Parts] [All Massey Ferguson Models]

Order Toll Free
(800) 853-2651
Mon-Fri 7am-7pm CT

Order online
anytime!

YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us!

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Website Accessibility Policy

Privacy Policy