Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

Question for Andrew Z

Welcome Guest, Log in or Register
Author 
Vito

02-22-2008 10:54:06




Report to Moderator

Andrew,
Was that your fathers tractor ,super H, that was pulling the homecoming float for the ag frat at this years parade?
Nice looking tractor.
Vito




[Log in to Reply]   [No Email]
Vito

02-22-2008 12:17:38




Report to Moderator
 Re: Question for Andrew Z in reply to Vito, 02-22-2008 10:54:06  
So you were driving.I went by you near the Mansfield Community Center traffic light.Took my wife,Uconn Alum, and two sons to the dairy barn and then onto the dairybar.Nice snowy day we are having!Which plow day were you referring to?
Vito



[Log in to Reply]  [No Email]
Andrew Z

02-22-2008 12:32:41




Report to Moderator
 Re: Question for Andrew Z in reply to Vito, 02-22-2008 12:17:38  
I tell you that hill is hell of a climb in 5th gear. I think i would have not had to much of an issue if that tractor was alittle slower in 5th it does 25-28mph on a up grade, never mind if you go down hill... There is one in woodstock with the old iron club. Also plow a little bit in Hampton for a guy last year i used my Super C with the fast hitch plow to break the sod. have fun moving the white stuff, got about 4" here @ 4:00 pm

Andrew

[Log in to Reply]  [No Email]
Andrew Z

02-22-2008 11:35:35




Report to Moderator
 Re: Question for Andrew Z in reply to Vito, 02-22-2008 10:54:06  
Yes Vito, that was my fathers tractor i used it to pull the Alpha Gamma Rho float in the homecoming parade this year at UConn. I tell you what i was happy that i left the 3 sets of rear and 2 sets of front weights on it :) i think with out them breaking would have been alittle sketchy espicaly when i went down the backside of horsebarn hill. Its sure a fun tractor to drive and sounds impressive with the 3" straight pipe. (actually to loud for pratical use though) Ill be doing it again this fall as i have to go one more sem. for ag ed. This time i may... have a Super MD to pull it :)

Andrew

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy