International Harvester / Farmall 3616 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Pedal Shaft Seal - This brake pedal shaft seal has a 1.125 inch Inside Diameter, a 1.832 inch Outside Diameter and is .25 inch wide. It Fits: 230, 3514, B-450, C, H, HV, I6, ID6, M, MD, MDV, MTA, MTAV, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6, Super W6TA, Super WD6TA, W4, W6, W6TA, WD6, 200, 240, 300, 330, 340, 350, 3600A, 3616, 400, 404, 450, 460, 504, 544, 560, 606, 656, 660, 664, 666, 686, 400, W400, 450, W450, 8000, Hydro 70, Hydro 86. Replaces: 354514R91, 360076R92, 364471R91, 380959R91, 380960R91, 47169A, 555397R91, 581646R91, U17944, 476838 (Item #: 153586, Ref: AB2578R) $15.50
Disc Brake Ball Bearing - Measuring 7/8 inches, this ball bearing is used in many disc brake systems. Typically 4 or 6 used per wheel. Replaces OEM numbers 09384AB, 150734A1, 16028R1, 166264, 16779X, 17028R1, 20063060, 2073622, 211-1028, 211-1328, 211-19, 211-221, 31-1750393, 33-0026328, 50A4272, 706039R1, 706039R2, 72073622, 7A2606, 0166264, 81716998, 81847078, 81866502, 82979987, 87554519, 87672308, 9170150, 920095936, 9959976, 9960587, BDB78, D5NN2N141A, E94FB9, E9NN2N324AA, E9NN2N324AB, GM145662, K963645, M830T, O9384AB (Item #: 126209, Ref: M830T) $3.00

Clutch
No Picture Clutch Alignment Tool - 1-1/8 inch 10 spline, 1-11/16 inch 16 spline, .787 inch pilot. For tractor models 460, 664, 666, 686, 3616. (Item #: 122257, Ref: S.70927) $26.30
No Picture Clutch Alignment Tool - 1-1/8"x10 and 1-11/16"x16 Spline, .787" Pilot - For International / Farmall tractor models 300, 330, 340, 350, 504, 544, 606, 656, 664, 666, 686, 2504, 2544, 2606, 2656, 3616, Pilot Diameter: .787", 1st Spline: 1-1/8", 10 Spline, 2nd Spline: 1-11/16", 16 Spline, (Item #: 176767) $43.60
Clutch Alignment Tool - 1-3/32"x10 and 1-11/16"x16 Spline - For International / Farmall tractor models 300, 330, 340, 350, 460, 504, 544, 606, 656, 664, 666, 686, 2500, 2504, 2544, 2606, 2656, 3514, 3616, 8000, Pilot Diameter: .787, Large Spline: 1-11/16" 16 Spline, Small Spline: 1-3/32" 10 Spline, (Item #: 122048) $26.30
Clutch Disc - 10-1/2 inch diameter, 1-1/8 inch hub, 10 spline. For tractor models 300, 330, 340, 350, 460, 504, 655, 606, 2500, 2504, 2544, 2606, 3616, 8000. (Item #: 166104, Ref: 384633R91) $189.00
Clutch Disc - 11 inch diameter, 1-3/32 inch hub, 10 spline. For tractor models 656, 664, 666, 686, 2656, 3616. (Item #: 184835, Ref: 388625R91) $185.00
No Picture Clutch Disc, 4 Pad - For International / Farmall tractor models 656 (Gas: s/n 1946-later; Diesel: s/n 2118-later), 664 (Gas: s/n 1946-later; Diesel: s/n 2118-later), 666 (Gas: s/n 1946-later; Diesel: s/n 2118-later), 686 (Gas: s/n 1946-later; Diesel: s/n 2118-later), 2656 (Gas: s/n 1946-later; Diesel: s/n 2118-later), 3616 (Gas: s/n 1946-later; Diesel: s/n 2118-later), Compatible with International Construction and industrial models 3616 (Gas: s/n 1946-later; Diesel: s/n 2118-later), Replaces International OEM number 388625, Clutch Size: 11", Clutch Hub: 1-3/32", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 4 Reg Pads, (Item #: 166064) $146.00
Clutch Disc, Organic - New, 10.5 inch, spring loaded, 1.125 inch spline diameter, 10 splines. For tractor models 2500, 2504, 2544, 2606, Farmall 300, 330, 340, Farmall 350, (3616 diesel serial number up to 2117 or gas up to serial number 1945), 460, 504, 544, 606. (Item #: 156475, Ref: 360488R92) $96.00
Clutch Disc, Remanufactured, 384633R91 - For International / Farmall tractor models 300, 330, 340, 350, 460, 504, 544, 606, 2404, 2544, 2606, 3616, Compatible with International Construction and industrial models 3514, 3616, Replaces International OEM number 384633R91, 384633R91R, Clutch Size: 10-1/2", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 6 Reg Pads, (Item #: 205053) $175.50
Clutch Disc, Remanufactured, 384633R91 - For International / Farmall tractor models 300, 330, 340, 350, 460, 504, 544, 606, 2504, 2544, 2606, 3616, Replaces International OEM number 384633R91, 384633R91R, H384633, Clutch Size: 10-1/2", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 4 Reg Pads, (Item #: 205990) $95.00
Clutch Disc, Remanufactured, 388625R93 - For International / Farmall tractor models 656, 664, 666, 686, 2656, 3514, 3616, Compatible with International Construction and industrial models 3616, Replaces International OEM number 388625R93, 388625R93R, Clutch Size: 11", Clutch Hub: 1-3/32", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 6 Reg Pads, (Item #: 203639) $167.50
Clutch Disc, Remanufactured, 388625R93 - For International / Farmall tractor models 656, 664, 666, 686, 2656, 3616, Compatible with International Construction and industrial models 3616, Replaces International OEM number 388625R93, 388625R93R, Clutch Size: 11", Clutch Hub: 1-3/32", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 4 Reg Pads, For a New version of this sku use Item #: 184835, (Item #: 204190) $109.00
Clutch Disc, Remanufactured, 388625R93 - For International / Farmall tractor models 656, 664, 666, 686, 2656, 3514, 3616, Compatible with International Construction and industrial models 3514, 3616, Replaces International OEM number 388625R93, 388625R93R, 388625HD8, Clutch Size: 11", Clutch Hub: 1-3/32", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 8 Reg Pads, (Item #: 204415) $170.01
Clutch Kit - For International / Farmall tractor models 300, 330, 340, 350, 460, 554, 606, 2504, 2544, 3616, Replaces International OEM number 360488R92, 360746R1, Clutch Size: 10-1/2", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: Woven, Pressure Plate Size: 10-1/2", Pressure Plate Levers: 3, Pressure Plate Hub Diameter: 1-11/16", Pressure Plate Splines: 16, (Item #: 156480) $300.00
Clutch Kit, 10-1/2 Inch - This remanufactured single stage clutch kit includes a 10 1/2 inch, 9 spring, 16 spline, 1 11/16 inch hub remanufactured pressure plate assembly, a 10 1/8 inch, 10 spline, 1 1/8 inch hub, 4 pad remanufactured clutch disc; new release bearing and two new pilot bearings. For tractors: 300, 320, 330, 340, 350, 460, 504, 544, 606. Industrial: 2500, 2504, 2544, 2606, 3616 (gas to serial number 1945 and diesels to serial number 2117). (Item #: 202008, Ref: 360746NC) $329.60
Pressure Plate Assembly - For International / Farmall tractor models 656, 664, 666, 686, 2656, 3616 (Gas, s/n 1946-later, Diesel, s/n 2118-later), Replaces International OEM number 388616R91, 11" Diameter, 1-3/4", 16 Spline, Fixed, Additional Handling and Oversize Fees Apply To This Item, (Item #: 166080) $346.00
Pressure Plate, Remanufactured - For International / Farmall tractor models 300, 330, 340, 350, 460, 504, 544, 606, 2500, 2504, 2544, 2606, 3514, 3616, 8000, Pressure Plate Size: 10-1/2", Pressure Plate Levers: 3, Pressure Plate Springs: 9, Pressure Plate Hub: 1-11/16", Pressure Plate Spline: 16, Pressure Plate Type: Single Stage, Additional Handling and Oversize Fees Apply To This Item, (Item #: 206066) $122.01

Cooling System
Thermostat - This Thermostat opens at 180 degrees F. It is used on the following Diesel tractors: 2606, 2706, 300, 350, 3616, 400, 450, 460, 560, 606, 656, 660, 706, TD6. Replaces 262882R1, 313942R91 (Item #: 110455, Ref: 70229927) $20.30
No Picture Water Pump Gasket - Plate to Block - For International / Farmall tractor models Hydro 70, Hydro 86, 340, 460, 504, 560, 606, 656, 660, 666, 686, 706, 756, 766, 806, 826, 856, 2504, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3514, 3616, Compatible with International Combine (s) 101, 303, 315, 403, 503, 615, 715, Compatible with International Harvester (s) 414, 420, 616, 622, Compatible with International Construction and industrial models T6, T340, TD6, TD9, 3514, 3600, 3616, 3800, 3850, Compatible with International Hay Cutting (s) 275, 375, Replaces International OEM number 69676R1, For Reman Water Pump use Item #: 107892, (Item #: 156625) $5.30
Water Pump, Remanufactured, 601816C92 - For International / Farmall tractor models Hydro 70, Hydro 86, 340, 460, 504, 560, 606, 656, 660, 666, 686, 706, 756, 766, 806, 826, 856, 2504, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3514, 3616, Compatible with International Combine (s) 303, 315, 403, 503, 615, 715, Compatible with International Harvester (s) 414, 420, 616, 622, Compatible with International Construction and industrial models 3514, 3616, 3850, Compatible with International Hay Cutting (s) 275, 375, Replaces International OEM number 601816C92, 749170C91, Replaces Casting number 169204R1, 303394R2, 318118R2, Includes pump to backplate gasket, Includes backplate, Includes backplate to block gasket, For a New version of this sku use Item #: 156625, (Item #: 204199) $100.01

Electrical System
Alternator - Alternator, 12 volt, 61 amp, external regulator, 2 terminal 12 o-clock position. For 100, 1000, 105, 1066, 110, 1100, 1110, 115, 120, 1200, 1206, 1256, 1275, 1300, 1456, 1466, 1468, 200, 205, 210, 21206, 21256, 21456, 222, 225, 23, 230, 2444, 2544, 2606, 2656, 2706, 275, 2756, 2806, 2856, 3110, 315, 3410, 3444, 3514, 3516, 3616, 375, 3800, 3850, 403, 4100, 4300, 444, 503, 504, 544, 601, 602, 606, 616, 622, 656, 706, 756, 766, 806, 815, 856, 915, 966, HYDRO 100. (Item #: 113606, Ref: 1100883) $123.00
Distributor Dust Cover - Used with horizontal IHC distributor 353898R11 or J4 magneto on Models: 424, 444, 450, W450, 460, 504, 560, 600, 606, 650, 656, 660, 706, 756, 806, 826, 856, 3514, 3616. Replaces 384831R91. (Item #: 107074, Ref: 353900R11) $16.10
Distributor Terminal Screw - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a zinc plated Terminal Screw. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. Replaces International part number 353907R1 (Item #: 118472, Ref: 353907R1) $7.80
Distributor Terminal Screw Insulator - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a spring anchor terminal insulator. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. (Item #: 118473, Ref: 353906R1) $7.20
Glow Plug - Sold individually. 0.197 inch tip diameter, 5 inch overall length and 0.311 inch outside diameter where it slides into the head. For combines: 101, 151, 181, 315, 403, 453, 503, 715. For Tractors TD6, TD9, 340, 460, 504, 560, 606, 656, 660, 706, 3514, 3616, 3800, 3850, TD340. Replaces 304131R1, 343977R1, 343894R1, 304131R3, 304131R2. (Item #: 111187, Ref: 304131R3) $17.00
Key Switch, 2 Terminal - With keys. For tractor models 3444, 3514, 3616, 4100, 4156, 4166, 4186, 4366, 4386, 615, 715, 815, 915. Replaces 370375R91, 379594R92, 403562R2. (Item #: 113393, Ref: 366313R91) $14.30
No Picture Starter - Delco Replaces OEM 1107543, 1107564, 1108657. TYPE: DR 20MT, 9 teeth, CCW rotation, volt/KW: 12. NOTE :C-221 Gas/LPG, LPG Engine (YR.59-58). Fits these models: 340 DSL (1962-63), 350 DSL (1956-58), 350 DSL (1957), 3514 DSL (1965-66), 3616 DSL (1965-66), 460 DSL (1958-59), 460 DSL (1962-64), 460 GAS, LPG, (1960-61), 460 GAS, LPG, (1960-64), 460 GAS with LPG, (1958-59), 460HC GAS, LPG, (1960-64), 504 DSL (1961-66), 560 GAS with LPG, (1958), 560 GAS with LPG, (1958-64), 560HC GAS with LPG, (1958-64), 606 DSL (1961-66), 606 GAS, LPG, (1961-64), 656 GAS, LPG, (1965-66), 660 GAS, LPG, (1960-61), 660 GAS with LPG (1958-59), T340 (1960-62), TD340 (1962-64), TD340 (1967), 560 GAS with LPG, (1959-64). Refundable $55.00 core charge will be added to your order. (Item #: 203447, Ref: TS-1032) $381.10
No Picture Starter - For tractor models (460 Gas, 1958 to 1959), (460, 560, 660, 606, 706 Gas, 1960 to 1967), (T340, 3515 Gas, 1958 to 1959 and 1965 to 1967), (T6 Crawler 1958 to 1963), (F504 Gas 1961 to 1965), (F656 Gas 1965 to 1966) (3616 1965). REBUILT Starter. 12 Volt. Also replaces 1107229, 1107744. (Item #: 203200, Ref: 1107720) $360.50
No Picture Starter - Delco (4193) - For International / Farmall tractor models 460 (D, 1960-63), 504 (D, 1961-66), 504 (D, Farmall, 1961-66), 560 (Farmall, Gas and LP1965-66), 606 (Diesel, 1962-67), 606 (Gas and LP, 1962-67), 656 (Gas and LP, 1965-66), 656 (Farmall, Gas and LP1965-66), 3514 (with D-188 Diesel or D-236 Diesel, 1965-66), 3616 (with D-188 Diesel or D-236 Diesel, 1965-66), Replaces Case IH OEM number 336770R91, 374583R91, 381904R91, Replaces Delco Remy Starter number 1107543, 1107564, 1998333, 323-685, Replaces Starter number 4193, Lester 4193, Volts: 12, Teeth: 9, Rotation: Counter Clockwise (CCW), Type: Direct Drive, (Item #: 189444) $465.00
No Picture Starter - Delco (4271, 4282) - For International / Farmall tractor models Hydro 70 (Gas), Hydro 86 (Gas), 504 (s/n: 15261-later, Farmal Diesel), 504 (s/n: 17830-later, Diesel), 544 (Hydro, Gas), 656 (Hydro, Gas, Late s/n), 656 (s/n: 36467-later, Hydro, Farmal, Gas), 666 (Hydro, Gas), 3616 (1967-70, Diesel), Compatible with International Construction and industrial models 2504 (s/n: 15261-later, Diesel), 2504 (s/n: 17830-later, Diesel), 3514 (1967-69, Diesel), 3514 (1970-71, C173 Hydro, Gas), Replaces Case IH OEM number 369459R93, 396459R91, Replaces Delco Remy manufacturer number 1107854, 1107855, 1998496, 323-691, Replaces Starter number 4271, 4282, Lester 4271, 4282, Volts: 12, Rotation: Counter Clockwise (CC), Direct Drive, Teeth: 10, (Item #: 189419) $421.00
Starter Delco Style DD (4236), Used - For International tractor models 504 (Gas), 544 (Gas), 656 (Gas), 666 (Gas), 686 (Gas), 2544 (Gas), 3514, 3616 (all C-221 Gas), Compatible with International Combine(s) 815, 915 (all gas), Replaces International OEM number 396523R92, 1108344, 1109360, 140-746, 396522R91, 396523R93, 396556R92, 4236, 44-4527, 74236, A485615Z, 1108343, Delco 12 Volt, CCW, 10 Tooth Drive, For a new version of this item use Item #: 203453, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 403453) $194.01
No Picture Starter, Rebuilt - A rebuilt Delco start that is 12 volts, counter clockwise rotation and has a 10 tooth starter drive for (544, 2544, 656, 2656, all Gas with ST, 1967 to 1973), (3514, 3616 Gas 1967 to 1973), (504, 3514 Gas 1969 to 1974), (C-200, 263 Gas 1968 to 1970), (3514 with C-173 Engine with ST 1969 to 1970), (915 Gas Combines 1969 to 1974), (666 with ST 1972 to 1974), (F-686 AG Tractor 1977 to 1979), (706 Gas 1967 to 1968), (766 Gas 1967 to 1968). REBUILT Starter. 12 Volt). Replaces 1108343. (Item #: 203453, Ref: TS-1230) $359.57
Switch, Push Button - This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length. Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: 271179R91, 367678R91, 373611R91, 393209R91. (Item #: 121141, Ref: R7994) $12.50

Engine Bearings
Camshaft Bearing Kit - 4 bearings. For tractor models 2606, 2656, 2706, 2756, 2806, 2826, 2856, 460, 560, 606, 656, 660, 666, 686, 706, 756, 766, 806, 826, 856, HYDRO 70, HYDRO 86. All with either C221, C263, C291, C301, D236, D282 6 cylinder engines. Can Be used on C157, C175 and C200 Engines by also purchasing 398019R1 front cam bearing separately. Not for German Diesel Engines. Replaces 130476R91, 130476R92, 130476R93, 70131R1, 70132R1, 70259R2, 70260R1, 70260R2, 70261R2, 70262R1, 71326R1 (Item #: 106671, Ref: CBK-H221) $36.10
Main Bearing Set, .010 - Main Bearing Kit (.010 over) with 4 inch thrust flange. Used on Hydro 70, Hydro 86, 460 (s/n 35093-later), 560 (s/n 44822-71777), 606 (s/n 13754-16620), 656, 660 (s/n 44822-71777), 666, 686, 706, 756, 766, 806, 826, 856, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616 (s/n 13754-16620), 205, 303, 315, 403, 403 (s/n 44821-later), 453, 503, 715, 414 (s/n 36693-later), 420 (s/n 36693-later), 616, 622, T6 (s/n 56634-later), 3800, 3850. Compatible with International Engines: C221, C263, C291, C301, D236, D282, DT282, D301. Replaces 376670R91, 332276R91, 376673R91, 376679R91 (Item #: 167378) $110.00
Main Bearing Set, .020 - Main Bearing Kit (.020 over) with 4 inch thrust flange. Used on Hydro 70, Hydro 86, 460 (s/n 35093-later), 560 (s/n 44822-71777), 606 (s/n 13754-16620), 656, 660 (s/n 44822-71777), 666, 686, 706, 756, 766, 806, 826, 856, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616 (s/n 13754-16620), 205, 303, 315, 403, 403 (s/n 44821-later), 453, 503, 715, 414 (s/n 36693-later), 420 (s/n 36693-later), 616, 622, T6 (s/n 56634-later), 3800, 3850. Compatible with International Engines: C221, C263, C291, C301, D236, D282, DT282, D301. (Item #: 190746) $222.00
Main Bearing Set, .030 - Main Bearing Kit (.030 over) with 4 inch thrust flange. Used on Hydro 70, Hydro 86, 460 (s/n 35093-later), 560 (s/n 44822-71777), 606 (s/n 13754-16620), 656, 660 (s/n 44822-71777), 666, 686, 706, 756, 766, 806, 826, 856, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616 (s/n 13754-16620), 205, 303, 315, 403, 403 (s/n 44821-later), 453, 503, 715, 414 (s/n 36693-later), 420 (s/n 36693-later), 616, 622, T6 (s/n 56634-later), 3800, 3850. Compatible with International Engines: C221, C263, C291, C301, D236, D282, DT282, D301. (Item #: 167101) $88.00
Main Bearing Set, Standard - Main Bearing Kit (standard) with 4 inch thrust flange. Used on Hydro 70, Hydro 86, 460 (s/n 35093-later), 560 (s/n 44822-71777), 606 (s/n 13754-16620), 656, 660 (s/n 44822-71777), 666, 686, 706, 756, 766, 806, 826, 856, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616 (s/n 13754-16620), 205, 303, 315, 403, 403 (s/n 44821-later), 453, 503, 715, 414 (s/n 36693-later), 420 (s/n 36693-later), 616, 622, T6 (s/n 56634-later), 3800, 3850. Compatible with International Engines: C221, C263, C291, C301, D236, D282, DT282, D301. Replaces 382357R91, YTO MBK221A (Item #: 185622, Ref: MBK221A) $99.00

Engine Gaskets
Conversion Gasket Set - For International / Farmall tractor models 454, 460, 544, 574, 606, 674, 2400, 2400A, 2400B, 2500A, 2500B, 2606, 3616, Compatible with International Construction and industrial models 2505B, 3500A, 8000, Compatible with International Engine (s) C157, C175, C200, Compatible with International Hay Cutting (s) 375, Replaces International OEM number 398178R92, Contains all gaskets necessary to complete an overhaul that are not included in the head gasket set, Crankshaft seals included, (Item #: 106724) $145.00
Conversion Gasket Set - For International / Farmall tractor models 560, 606, 656, 660, 706, 2606, 2656, 2706, 3616, Compatible with International Combine (s) 101, 151, 181, 315, 403, 503, 615, 715, Compatible with International Harvester (s) 414, 420, Compatible with International Construction and industrial models TD6 (62 Series), TD9B, Compatible with International Engine (s) D236, D282, DT282, D301, (Item #: 168998) $83.00
Front Crankshaft Seal - This front crankshaft seal has a 2.375 inch Inside Diameter, a 3.355 inch Outside Diameter and is 0.475 inch wide. It Fits: 2400, 2405B, 2410B, 2412B, 2500A, 2500B, 2505B, 2510B, 2514B, 3400A, 3500A, 4500B, 454, 544, 574, 666, 674, 686, 756, 766, 806, 826, 856 (Gas and LP), 340, 504 (Diesel), 350 (W/ GD193 Diesel), 3514 (Diesel, with D188 engine), 3616, 460, 560, 606, 656, 660 (Gas, LP and Diesel, when used as a front crankshaft seal), 706 (Gas, LP and Diesel, when used as a front crankshaft seal, except German Diesel), Hydro 70, Hydro 86 (Gas and LP). Replaces: 117568H1, 119020H1, 129370H1, 273573R91, 317549R91, 357672R91, 391976R91, 606750C91 (Item #: 106642, Ref: 834831M1) $12.20
Full Gasket Set - For 460, 606, 656, 2606, 2656, 27063514, 3616 with D236 Diesel Engine (Item #: 106721, Ref: FS3843) $205.00
Head Gasket - For International / Farmall tractor models 460, 560, 606, 656, 706, 2706, 3616, Compatible with International Engine (s) D236 (Diesel), D282 (Diesel), Replaces International OEM number 134400A1, (Item #: 128679) $129.00
Head Gasket Set - Used on International D301, UD236, UD282, UDT282, D236, D282, DT282 6 Cylinder Engines. It includes nozzle and precup gaskets. Replaces 134403A1 (Item #: 106690, Ref: HS3843) $136.00
Push Rod Cover Gasket - For International / Farmall tractor models Hydro 70, Hydro 86, 460, 560, 606, 656, 660, 666, 686, 706, 756, 766, 806, 826, 856, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616, Compatible with International Construction and industrial models 3600A, 3800, 3850, Compatible with International Engine (s) C221, C263, C291, C301, D236, D282, Replaces International OEM number 369982R1, Additional Handling and Oversize Fees Apply To This Item, (Item #: 128736) $16.30
Valve Cover Gasket - For International / Farmall tractor models 460, 560, 606, 656, 706, 2706, 3616, Compatible with International Engine (s) D236 (Diesel), D282 (Diesel), Replaces International OEM number 278308R3, Additional Handling and Oversize Fees Apply To This Item, (Item #: 128680) $12.60
Valve Cover Gasket - For International / Farmall tractor models Hydro 70, Hydro 86, 460, 560, 606, 656, 660, 666, 686, 706, 756, 766, 806, 826, 856, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616, Compatible with International Construction and industrial models 3600A, 3800, 3850, Compatible with International Engine (s) C221, C263, C291, C301 (Gas), Replaces International OEM number 369983R2, Additional Handling and Oversize Fees Apply To This Item, (Item #: 128683) $10.50

Engine Rebuild Kits
Cylinder Sleeve - For International / Farmall tractor models 606, 656, 706, 2706, 3616, Compatible with International Engine (s) D282 (s/n 71777-later), Replaces International OEM number 609028C21, 609028C1, 3.873" Flange Diameter, (Item #: 128622) $30.80
Engine Cylinder Sleeve - For International / Farmall tractor models 340, 460, 504, 560, 606, 656, 660, 706, 2504, 2606, 2656, 2706, 3514, 3616, Compatible with International Combine (s) 101, 151, 181, 403, 615, Compatible with International Harvester (s) 414, 420, Compatible with International Construction and industrial models TD9, TD9B, TD340, 2500, Compatible with International Engine (s) D166 (early), D188 (early), D236, D282 (.875" pin, wide flange liner), DT282 (1.125" pin, wide flange liner), Replaces International OEM number 278272R1, Bore: 3.6875", Flange O.D.: 4.165", Flange Thickness: .1875", (Item #: 108753) $67.00
No Picture Overhaul Kit - 3 9/16 inch bore. For 606, 2606, 3616 with C221 Gas Engine. Contains pistons with pins and retainers, piston sleeves, overhaul gasket set, rod bearings, main bearings. (Item #: 183871, Ref: R3386-OHK) $2199.01

Engine Parts
Camshaft - For International / Farmall tractor models Hydro 70, Hydro 86, 460 (engine s/n 5610-later), 560 (engine s/n 6765-earlier), 606, 656, 666, 686, 706, 756, 766, 806, 826, 856, 2606 (engine s/n 12799-13753), 2656, 2706, 2756, 2806, 2826, 2856, 3616, Compatible with International Combine (s) 101 (engine s/n 11028-later), 151, 181, 205, 303, 315, 403, 453, 503, 615 (engine s/n 44821-earlier), 715, Compatible with International Harvester (s) 414, 420, 616, 622, Compatible with International Construction and industrial models T6 (engine s/n 36694-56634), TD6 (early), TD9, TD9B (engine s/n 6902-earlier), 3800, 3850 (engine s/n 71777-later), Compatible with International Engine (s) C221, C263, C291 (late), C301, D236 (narrow flange liners), D282, DT282, D301 (narrow flange liners), Replaces International OEM number 367229R1, (Item #: 160894) $286.00
Connecting Rod, Used - For International tractor models Hydro 70, Hydro 86, 454, 460, 464, 544, 560, 606, 656, 660, 666, 674, 686, 706, 756, 806, 856, 2400A, 2400B, 2500, 2500A, 2500B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616, Compatible with International Combine(s) 50, 205, 303, 315, 403, 715, Compatible with International Harvester(s) 55, 350, 414, 420, 550, 616, 622, 650, Compatible with International Engine(s) C157, C175, C200, C221, C263 (C282), C291, C301, Replaces International OEM nos 367406R21, 367406R11, 367406R12, LP and Gas Engines Only, Pin Diameter: .875", Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 498381) $25.01
No Picture Exhaust Valve Seat - For International / Farmall tractor models Hydro 70, Hydro 86, 454, 460 (s/n 35093-earlier), 464, 544, 560 (s/n 36693-later), 574, 606 (s/n 35093-earlier), 656, 660 (s/n 38981-later), 666, 674, 686, 706, 756, 766, 806, 826, 856, 2400A, 2400B, 2500A, 2500B, 2544, 2606 (s/n 35093-earlier), 2656, 2706, 2756, 2806, 2826, 2856, 3514, 3616, Compatible with International Combine (s) 151, 181, 205, 303, 315, 403 (s/n 2225-earlier), 453, 615, 715, Compatible with International Harvester (s) 414 (s/n 36693-later), 420 (s/n 36693-later), 616, 622, Compatible with International Construction and industrial models T6 (s/n 36694-56634), 100, 2400A, 2400B, 2405B, 2410B, 2500A, 2500B, 2505B, 2510B, 3400A, 3500A, 3800, 3850, 4500B, 8000, Compatible with International Engine (s) C157, C200, C221, C263, C291, C301, Replaces International OEM number 126373R1, (Item #: 185617) $5.00
No Picture Head Biolt Kit - For International / Farmall tractor models 560 (Engine s/n 6766-44821), 606 (Engine s/n 13754-16620), 660 (Engine s/n 4370-44821), 2606 (Engine s/n 13754-16620), 2656 (Engine s/n 7177-later), 3616 (Engine s/n 13754-16620), Compatible with International Combine (s) 151, 181, 315, 403, 503, 615, 715, Compatible with International Harvester (s) 414, 420, Compatible with International Construction and industrial models TD6 (62 Series), Compatible with International Engine (s) D236, D282, Replaces International OEM number 7326896, 53268128, NR76126, (Item #: 170117) $222.00
Push Rod - For [Hydro 70, Hydro 86, 454, 464, 544, 574, 666, 674, 686, 756, 806, 826, 856, 2544, 2756, 2806, 2826, 2856 (Gas and LP Only)], [340, 504, 2504 (Diesel)], [460, 560, 606, 656, 660, 706, 2606, 2656, 2706 (Gas, LP, Diesel (No German Diesels)], [Industrial: 100C, 2400A, 2400B, 2405B, 2410B, 2412B, 2500A, 2500B, 2505B, 2510B, 2514B, 3400A, 3500A, 3600A, 4500A, 4500B, 8000, T6-62, T7 (Gas and LP Only)], [150, H25B, H30A, H30F, H30R, H50A, H50B, H50C, H60B, S7A, S7B, TD340, TD6-62, TD9-91, TD9-92, TD9B (Diesel)], CONSTRUCTALL: 2500 (Diesel), [Industrial: 3514, 3616, 3800, 3850, H30B (Gas, LP, Diesel (No German Diesels)]. Replaces: 164436R91. Size: 12.684 O/A length, .375 tube dia. (Item #: 184399, Ref: 164436R91) $19.90
Valve Guide - For International / Farmall tractor models Hydro 70, Hydro 86, 454, 460, 544, 560, 574, 606, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856, 2400A, 2400B, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3616, Replaces International OEM number 237248R1, (Item #: 128515) $5.70
Valve Rotator - For International / Farmall tractor models Hydro 70, Hydro 86, 340, 454, 460, 464, 544, 560, 574, 606, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856, 2400A, 2400B, 2500A, 2500B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3514, 3616, Compatible with International Combine (s) 101, 151, 181, 205, 303, 315, 403, 615, 715, Compatible with International Harvester (s) 414, 420, 616, 622, Compatible with International Construction and industrial models T6, TD6, TD340, 100, 2500B, 2505B, 3500A, 4500B, 8000, Compatible with International Hay Cutting (s) 375, Replaces International OEM number 375604R91, Replaces International Casting number 278368R, Engine: D282 early, Use with Head Casting No. 278368R, (Item #: 109732) $57.00
No Picture Valve Spring - For International / Farmall tractor models Hydro 70, Hydro 86, 340, 454, 460, 464, 560, 606, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856, 2400A, 2400B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 3514, 3616, Compatible with International Combine (s) 50, 101, 151, 181, 205, 303, 315, 403, 453, 715, Compatible with International Harvester (s) 616, 622, Compatible with International Construction and industrial models TD340, 100, 2400A, 2400B, 2405B, 2410B, 2500A, 2505B, 2510B, 3400A, 3500A, 3800, 3850, 4500B, 8000, Compatible with International Engine (s) C157, C175, C200, C221, C236, C263, C291, C301, D166, D236, D282, DT282, Compatible with International Hay Cutting (s) 375, Replaces International OEM number 367192R1, (Item #: 185589) $4.70
Valve Train Kit - For International / Farmall tractor models 460 (engine s/n 5610-later), 560, 606, 656, 660, 706, 2606, 2656, 2706 (engine s/n 44822-71777), 3616 (engine s/n 16620-later), Compatible with International Combine (s) 101 (engine s/n 11028-later), 151, 181, 315, 403, 453, 503, 615 (engine s/n 44821-later), 715 (s/n 23000-earlier), Compatible with International Harvester (s) 414, 420, Compatible with International Construction and industrial models TD9 (92 series), TD9B (engine s/n 6903-11440), 3800, 3850 (engine s/n 71777-later), Compatible with International Engine (s) D236, D282, DT282, D301 (all 6 cylinder diesel), For applications with rotator below spring, Kit includes: Intake and exhaust valves, guides, springs and keepers, Intake Valves: 1.680" head diameter, 6.040" length, 45 degrees, Exhaust Valves: 1.370" head diameter, 6.060" length, 45 degrees, (Item #: 120319) $311.00
No Picture Valve Train Kit - For International / Farmall tractor models 460, 560, 606, 660, 2606, 3616, Compatible with International Combine (s) 205, 303, 315, 403, Compatible with International Harvester (s) 414, Compatible with International Engine (s) C221, C263, Includes: Valve Keeper, Intake Valve, Valve Guide, Exhaust Valve, Valve Spring, Valve Guide and Valve Rotator, (Item #: 169083) $345.00

Engine Pistons and Sleeves
Cylinder Sleeve - Used on C221 gas engines on 460, 606, 2606, 3616 and C263 gas engines on 560, 656, 660, 706, 2656, 2706, 3600A, 3800, 3850, this is a standard bore cylinder sleeve. It measures; Bore Diameter: 3.5625 inches / 90.4875mm, Flange Outer Diameter: 4.052 inches / 102.9208mm Flange Width: 0.189 inches / 4.8006mmm, Sleeve O.D. at Barrel: 3.6890 inches / 93.7006mm, Length: 7.625 inches / 193.6750mm. Replaces 367645R1, 3803698, RP141294, SD372 (Item #: 128647, Ref: 367645R1) $62.00
Sleeve and Piston Kit - Set of 6. For tractor models 460. (D236 CID Diesel 6-cylinder engine. Cupped head piston) and models 606, 2606 to engine serial number 16620. Sleeves, pistons and rings, pins and retainers. For 3-11/16 inch standard bore. (Item #: PK173) $993.60

Engine Rings
Piston Ring Set - .030" Oversize - Single Cylinder - For International / Farmall tractor models 460, 560, 606, 656, 660, 706, 2606, 2656, 2706, 3616 (all gas), Compatible with International Construction and industrial models 3600, 3616, 3800, 3850 (all gas), Compatible with International Engine (s) C221, C263, Standard Bore: 3.5625", Ring Size: .030” Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .250", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold per cylinder, For standard use Item #: 120862, (Item #: 120861) $31.98
Piston Ring Set - .040" Oversize - Single Cylinder - For International / Farmall tractor models 460, 560, 606, 656, 660, 706, 2606, 2656, 2706, 3616 (all gas), Compatible with International Construction and industrial models 3600, 3616, 3800, 3850 (all gas), Compatible with International Engine (s) C221, C263, Standard Bore: 3.5625", Ring Size: .040” Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .250", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold per cylinder, For standard use Item #: 120861, (Item #: 120862) $42.80
Piston Ring Set - Standard - 2 Cylinder - For International / Farmall tractor models 340, 460, 504, 560, 606, 656, 660, 706, 2504, 2606, 2656, 2706, 3514, 3616, Compatible with International Combine (s) 101, 151, 181, 315, 403, 615, Compatible with International Harvester (s) 414, 420, Compatible with International Construction and industrial models TD6, TD9B, TD340, 2500, Compatible with International Engine (s) D166, D188, D236, D282, DT282, Bore: 3.6875", Compression Rings per Piston: (2) @ .125", Oil Rings per Piston: (1) @ .250", Top Groove Size: .125", Top Groove Style: Half Keystone, Chrome 10 Degree, 2nd Groove Size: .125", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .250", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a 2 cylinder set, (Item #: 128966) $75.00
Piston Ring Set - Standard - 2 Cylinder - For International / Farmall tractor models 340, 460, 504, 560, 606, 656, 660, 706, 2504, 2606, 2656, 2706, 3514, 3616, Compatible with International Combine (s) 101, 151, 181, 315, 403, 615, Compatible with International Harvester (s) 414, 420, Compatible with International Construction and industrial models TD6, TD9B, TD340, 2500, Compatible with International Engine (s) D166, D188, D236, D282, DT282, Bore: 3.6875", Compression Rings per Piston: (2) @ .125", Oil Rings per Piston: (1) @ .250", Top Groove Size: .125", Top Groove Style: Half Keystone, Chrome 10 Degree, 2nd Groove Size: .125", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .250", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a 2 cylinder set, For single cylinder set use Item #: 108754, (Item #: 179121) $99.00
No Picture Piston Ring Set - Standard - Single Cylinder - For International / Farmall tractor models 460, 560, 606, 656, 660, 706, 2606, 2656, 2706, 3616 (all gas), Compatible with International Construction and industrial models 3600, 3616, 3800, 3850 (all gas), Compatible with International Engine (s) C221, C263, Replaces International OEM number 539379R2, Bore: 3.5625", Ring Size: Standard, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .250", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold per cylinder, For .030" use Item #: 120862, (Item #: 108033) $16.70

Exhaust System
Muffler, Aluminized - Vertical muffler for gas tractor, fits engines C221 and C263. Inlet inside diameter 2-3/8 inch, outlet outside diameter 2-1/2 inch, length 29 inches, diameter 6 inches, round body. Uses MC212 Muffler Clamp. For tractor models H, M, MD, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, 300, 450, 606, 2606, 656, 2656. Diesel engines D166, D188, D236, D282, models 340, 504, 2504, 3514, For 2500, 2504, 2606, 2656, 340, 3514, 3616, 450, 460, 504, 606, 656. Replaces 350601R95, 370773R91, 357288R92, 370644R91, 403551R1. For a black version order Item# 100807 (Item #: 185584, Ref: 370644R92) $42.30
Muffler, Black - This is a black version of 370644R92. Vertical muffler for gas and diesel applications.Fits engines C221 and C263. Inlet inside diameter 2-3/8 inch, outlet outside diameter 2-1/2 inch, length 29 inches, diameter 6 inches, round body. Uses MC212 Muffler Clamp. For tractor models H, M, MD, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, 300, 450, 606, 2606, 656, 2656. Diesel engines D166, D188, D236, D282, models 340, 504, 2504, 3514, For 2500, 2504, 2606, 2656, 340, 3514, 3616, 450, 460, 504, 606, 656. Replaces 350601R95, 370773R91, 357288R92, 370644R91, 403551R1 (Item #: 100807) $34.30

Fuel System / Air Intake
Carburetor Fuel Line Fitting With Strainer - Fits INTERNATIONAL carburetors: 356948R92, 35865R91, 366066R91, 367258R92, 367259R92, 372723R92, 378196R94, 379813R91, 380956R91, 381984R91, 388297R92, 388424R92, 388425R96, 390082R92, 396197R93, 45108DB, 45108DC, 50981DA, 50981DB, 50983DB, 52714D, 52814DA, 52815D, 52815DA, 533622R91, 53873DF, 53873DH, 539575R91, 56543DE, 60329DA. 1/4 inch pipe to 5/16 inch flare. (Item #: 111514, Ref: 29902DX) $16.20
Fuel Pipe Coupling Nut - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, F12, F14, H, HV, I4, I6, I9, M, MD, MTA, O4, O6, Super A, Super C, Super H, Super M, Super W4, TD6, TD9, W4, W6, W12, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 444, 450, 460, 504, 560, 600, 606, 650, 656, 660, 686, 706, 756, 806, 826, 856, 2444, 3514, 3616, Compatible with International Combine (s) 303, 403, 503, 615, 715, Replaces International OEM number 29899D, 700155R11, 700153R11, 1/2"-20 Hi-duty tube fitting, 5/16" O.D., (Item #: 112642) $3.47
Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. Replaces: 13194D, 25854, 49923D (Item #: 105364, Ref: 49923D) $3.50

Lights
Light Bulb, Sealed Beam, 12 Volt - This 12-Volt Sealed Beam has Double Contact. It is 35 Watt. Has a 4.365 inch outside diameter. Replaces: L4411, 131508C1, 134039H1, 144072H1, 21-521R1, 371461R91, 373662R1, 373662R91, 394770R2, 535850R1, 635959R91, 725-0133, 725-0222, 725-0588, 80627C1, 9410891, 86594207, 87779219, 925-0222. (Item #: 111241, Ref: 373662R91) $10.10

PTO / Driveline
PTO Seal - Measures 1.306 inch inside diameter, 2.220 inch outside diameter. THIS SEAL IS .312 InchES WIDE. VERIFY THE WIDTH OF YOUR OLD SEAL. YOU NEED TO INSTALL 2 OF THESE IF YOUR OLD SEAL IS WIDER. For tractor models Super A, H after serial number 118000, (M, MD, Super M, Super MTA and Super MD after serial number 59957), Late W4, W6, W9, Super W4, Super W6, Super W9, B250, B275, B414; Also fits the following models with transmission driven PTO (not Live PTO): MTA, 300, 330, 350, 354, 364, 384, 400, 424, 434, 444, 450, 454, 544, 600, 650, 2300, 3414, 3514, 3616. Replaces 3065217R91, 358772R91, 358812R91, 50702D, 372394R91, S90957, 708107R91. (Item #: 114730, Ref: 45702D) $9.80
PTO Shield - Two Piece For 06 Series thru 86 Series with Dual Speed PTO. OEM# 1264520C1 1264503C1 (Item #: 103968, Ref: R0907) $79.00
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $357.14
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.60
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $16.90
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.30
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $4.80
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.80
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.10
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $29.70
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $35.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.50
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.80
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $4.80
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $13.80
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.30
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.10
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.10
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.40
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $13.80
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $24.80
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.20
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.10
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.10
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.40
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $13.60
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.20
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.00

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.80
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.30
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.80
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.30
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.70
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $18.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.70
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $26.50

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $82.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $138.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $102.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $171.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $169.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $110.21
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.70
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $10.30
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.40

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $13.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.50
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $28.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $58.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $37.40
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $45.20
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $373.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $444.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $444.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.50
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $33.30

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.60
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.70
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.00
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.00

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $178.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $123.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.50
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $48.60
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $100.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.20
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $42.20
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $40.80
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.70
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $40.00
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $379.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $119.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.40
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $69.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $54.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.30
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.90
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $57.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $23.30
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $9.40
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $23.30
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.10
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $86.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.00
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $12.40
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $60.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $23.70
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $7.80
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $63.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $13.98
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.80
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $13.98
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $7.80
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $43.90