International Harvester / Farmall 500 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Clutch
Bearing - Pilot - New Pilot Bearing. 25mm (.9843 inch) inside diameter, 52mm (2.0472 inch) outside diameter with seals on both sides. For tractors: 400, 450, 500, 560, 600, 660, H, HV, M, M500, MD, MDV, MV, Super H, Super M, Super MD, Super MTA, Super W4, Super W6, W4, W6, WD6. (Item #: 100023, Ref: ST544) $5.40
Clutch Disc - 12 inch, 4 button, spring loaded, 1.1875 inch spline diameter, 11 spline. For tractor models 2706, 2756, 2806, 2826, 2856, 3088, 3288, 3688, 400, 450, 500, 560, 600, 660, 706, 756, 766, 786, 806, 826, 856, 886, 966, 986, Super MTA. (Item #: 112266, Ref: 384395R94) $154.00
Pressure Plate - Pressure Plate, 12 inch, 12 spring, 3 levers adjust on pivot point, 1.750 inch spline diameter, 17 spline. Flywheel step, 1.406 inch. For tractor models 400, 450, 500, 560, 600, 660, Super MTA. Replaces: 359121R97, 359121R96, 359121R95, 359121R94, 359121R93, 359121R92, 359121R91, 360079R94, 360079R93, 360079R91, 359041R93, 360080R91. (Item #: 166108, Ref: 359121R98) $459.00
Pressure Plate, Remanufactured - For International Construction and industrial model 500, Pressure Plate Size: 10", Pressure Plate Levers: 3, Pressure Plate Springs: Over Center, Pressure Plate Hub: 1-3/4", Pressure Plate Spline: 10, Pressure Plate Type: Single Stage, (Item #: 206071) $93.01

Decals and Emblems
Front Emblem - For 400, 500. Front Emblem "IH" Block. (R1959) (Item #: 103912, Ref: 362320R2) $28.90

Electrical System
Distributor Cap Spring Clip - Fits listed IH models when equipped with IH brand distributor 353898R11. Replaces: 107384C1, 353894R1 (Item #: 178117, Ref: 353894R1) $16.80
Distributor Terminal Screw - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a zinc plated Terminal Screw. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. Replaces International part number 353907R1 (Item #: 118472, Ref: 353907R1) $7.70
Distributor Terminal Screw Insulator - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a spring anchor terminal insulator. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. (Item #: 118473, Ref: 353906R1) $7.20
Switch, Push Button - This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length. Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: 271179R91, 367678R91, 373611R91, 393209R91. (Item #: 121141, Ref: R7994) $12.00

Engine Bearings
No Picture Bearing - Opening disc bearing used on planter models: 400 and 500 Cyclo fold and flex frame and 800 series: also used on dry fertilizer spreaders for 400 and 500 Cyclo and liquid fertilizer spreaders for 400 cyclo. .632 inch inside diameter, 1.7805 inch outside diameter, .73 inches wide. For 400, 500. (Item #: 107855, Ref: 492757R91) $6.00
No Picture Cam Bushing Set - For D207 Diesel engine. Complete for 1 engine. For tractor models 310, 350, 450, 450B, 480, 480B, 500, 580, 580CK, 580C, 580D. (Item #: 172271, Ref: CBS207) $37.90
Piston Pin Bushing - Used in British International engines: BC144, BD144, BD144A, BD144C, BD154, BD154C, BD154T. This Piston Pin Bushing has an inside diameter of 27.5mm. Used in International models: B275, B414, 424, 444, 354, 365, 384, 3414, 2424, 2444, 238, 500. Replaces OEM numbers 3043611R1, 711045R1, 3043611R93 (Item #: 108502, Ref: 3043611R1) $4.20

Engine Gaskets
Front Crankshaft Wear Sleeve - This Front Crankshaft Wear Sleeve is used in British Diesel Engines: BC144, BD144, BD144A, BD144C, BD154, BD154C, BD154T. It is used to repair wear where the front crank shaft seal goes into the front timing cover. (Item #: 184669, Ref: RP301112) $68.00
Valve Cover Gasket - This Valve Cover Gasket is used on Gas Engines; C113, C123, C135, C146, C153. It replaces OEM/Original part numbers 43378DB, 43378DD, 43378DE. (Item #: 128613, Ref: 43378DE) $10.40

Engine Parts
Camshaft - For tractor models B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500 with diesel engines. Replaces 709450R1, 3063934R3, 3064086R91. Verify 1 5/16 inch diameter on cam where cam gear fits on. Replacement gear available as part number 3064085R1. (Item #: 112371, Ref: 3063934R3) $96.00
Camshaft Gear - This Camshaft Gear is used with 3063934R3 Camshaft. Replaces 3064085R1, 703812R1 (Item #: 112370, Ref: 3064085R1) $32.60
Camshaft Retaining Plate - This Camshaft Retaining (Thrust) Plate used on IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 43249D (Item #: 180159, Ref: 43249D) $7.70
Connecting Rod - For tractor models 2424, 384, 424, 444, B414, with the BC144, BD144, BD154 gas/diesel engines engine. Replaces 3061214R91, 3061215R1, 061214R91, 306215R1, 704088R91, 706132R1 (Item #: 108438, Ref: 3061214R91) $51.00
Crankshaft - For tractor models 2424, 354, 364, 384, 424, 2300b 275, B414 all with either a BD144, or BD154 engine. Replaces 3110995R91, 751303R1 (Item #: 112327, Ref: 3110995R91) $324.72
Crankshaft Gear - This Crankshaft Gear used on IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 703865R1 (Item #: 112413, Ref: 703865R1) $36.40
Lifter, Refaced - These Valve Tappets (Lifters) are used on IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Diesel all with casting number 704782R1. Replaces 704782R1. (Item #: 112412, Ref: R1188333) $7.10

Exhaust System
Exhaust Manifold Gasket - This gasket is used with 3042719R11 manifold. Two are required. Sold individually. Replaces 704165R1, 704165R2, 704165R3, VPE3933. (Item #: 113661, Ref: 704165R2) $10.90
Exhaust Manifold, Vertical - For tractor models B275, 354, 384, B414, 444, 2300, 2444 all with diesel engines. Gasket available as p/n 704165R2. Replaces 3042719R11, 3045354R11. NOTE - THIS MAY BE SLIGHTLY DIFFERENT THAN YOUR ORIGINAL MANIFOLD AND YOUR HEAT SHIELD MAY NEED TO BE TRIMMED AS THIS CASTING MAY BE SLIGHTLY LARGER. (Item #: 113663, Ref: 3042719R11) $57.00

Fuel System / Air Intake
Carburetor - Features reversible linkage. This Zenith carburetor outperforms the original carbs used on: 424 and 444 and 500 crawler, replaces Marvel-Schebler# TSX896SL, TSX896, TSX930, TSX948, TSX949, TSXU834. Center to center on 2 mounting bolts is 2 5/16 inches. Made in USA, 1 year warranty. (Item #: 100748, Ref: 12566) $426.00
Carburetor - Features reversible linkage. This Zenith style carburetor outperforms the original carbs used on: 424 and 444 and 500 crawler, replaces Marvel-Schebler# TSX896SL, TSX896, TSX930, TSX948, TSX949, TSXU834. Center to center on 2 mounting bolts is 2 5/16 inches. Import. 1 year warranty. (Item #: 184603, Ref: 12566B) $293.00
Fuel Filter - The fuel filter measures 3 7/16 inches diameter, 2 3/4 inches tall. Comes with two large and one small rubber seal rings. Replaces A51346, A37187, A39109, G45288, 45288, 3602788R91, 309991, C3TZ9365B, 86546599, 309531, C3TA9176A, C3TZ9155B, C3TA9155B, 1021350M91, 1021351M1, 835944M91, 1596257M91, 1021351M3, A35668, 70000-14632, 7000014632 (Item #: 159728, Ref: 309991) $24.50
Fuel Injector Nozzle Sleeve - This Fuel Injector Nozzle Sleeve is used on D155, D179, D206, D239, D246, D268, DT268, D310, and D358 Engines. Brass Construction, 3.190 inch overall length 0.386 inch injector tip inside diameter. Replaces 73055344, 3055344R1 (Item #: 165847, Ref: 3055344R1) $33.00
Injector - This Injector is used on B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 1081629R91, 3040870R94 (Item #: 113286, Ref: 3040870R94) $65.98
Precombustion Chamber - This Pre-combustion Chamber is used on CASE-IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 3045523R1, (Item #: 113285, Ref: 3045523R1) $13.00
Precombustion Chamber Holder - This Precombustion Chamber Holder is used on B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 708314R1 (Item #: 113284, Ref: 708314R1) $19.20
Precombustion Chamber Lower Gasket - Pre Combustion Chamber Lower Gasket Fits Between Pre Combustion Chamber and Cylinder Head. Replaces 706105R93, 719383R1, 716156R97, 761107R93, 764939R92, 764940R91 (Item #: 184215, Ref: 710383R1) $3.30
Precombustion Chamber Upper Gasket - Pre Combustion Chamber Upper Gasket Fits Between Pre Combustion Chamber and Pre Combustion Chamber Holder. Replace 3132305R92, 706105R93, 710382R2, 710382R1, 710832R3, 716156R97, 710328R3, 761107R93, 764939R92, 764940R91 (Item #: 710382R3) $2.18

Hydraulic System
Hydraulic Pump Gear - This New Hydraulic Pump Gear has 16 teeth. It Fits: C, Super A, Super A-1, Super AV-1, Super C, T340 (gas with 9 GPM side engine mounted pump), [ T4, T5 (gas with 9 GPM side engine mounted pump) ], 100, 130, 140, 200, 230, 240, [ 2424, 2444, 340, 424, 444 (GAS) ], 330, 404, Crawler: 500 (GAS with 9 GPM side engine mounted pump). Replaces: 350709R1. (Item #: 121576, Ref: 350709R1) $101.00

Oil System
Oil Filter Base - This oil filter base and canister assembly is used on BD144 and BD154 engines. It uses 826137M91 filter. Used on 354, 364, 384, 3414, 2424, 2444, TD5, Early 500, 424, 434, 444, 464, B414, B275 Tractors. Replaces: 3042420R91, 3066851R91, 3069976R91, 3042425R1, 3043289R1, 3043291R1, 3043292R1, 3042428R1, 3043293R91, 3065965R1, 376364R91, 3043283R92, 3043315R1, 3042423R1, 3069975R91, 706592R1. (Item #: 112372, Ref: 3042420R92) $30.98
Oil Pan - This is the deep style oil pan. It is 7 inches deep. It is used on BD144, BD154 Engines. IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 3064063R11. (Item #: 158649, Ref: 3064063R11) $72.00
Spin-On Oil Filter Adapter Kit - This Spin-On Oil Filter Adapter Kit Fits Gas and LP Engines in IH Combines: 105, 122, 140, 203, 62, 64, 76, 91, 93. Fits IH Industrial: 2404, 2444, 2504, Crawlers: 500, 500C, T340, T340A, T4, T4B, T5, T5B, T5C, Forklift: 4000, Power Units: U123, U2, U2A, UC135, UC135B, UC153, Rubber Tired Loaders: 3514, H30F, H30R, H50. Fits Tractors: C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504. Fits Balers: 55T, 55W, 56T, 56W, 57T, Carrier: 660, Hi-Clear Sprayers: 770, 780, Windrowers: 161, 163, 201, 210, 225, 230, 275, 375; Replaces: 538828R91, 63856D (Item #: 184655, Ref: 538828R91KIT) $153.00

Steering
Front Axle Assembly, Wide, without hubs - For H, Super H, 300, 350. Complete Front Axle without hubs contains cap screws with lock washer, steering bracket assembly, rear saddle assembly, front saddle assembly, spindles and Castlellated nuts. Width on wide axles are adjustable from 60 inches to 86 inches. (Item #: 111415, Ref: 21015) $2508.20

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $365.01
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.87
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.10
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.60
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $4.90
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.80
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.50
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.10
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.10
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.80
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $4.90
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.00
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.40
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.40
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.30
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.60
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.00
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.10
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.30
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.30
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.40
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.60
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.90
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $11.20
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $18.60

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $94.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.50
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.90
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.20
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.80
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $27.00

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $78.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $108.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $176.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.78
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.80
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $11.00
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $12.70
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.10
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $28.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $59.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $39.90
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $45.20
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $14.90

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $367.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $440.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $440.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.28
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $25.70
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $14.70
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.60
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.60

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $120.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.70
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.80
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $98.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $45.00
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $42.00
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.70
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $42.00
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $390.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $119.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.50
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $68.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $54.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.30
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $55.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.60
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.90
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $58.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $23.40
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $9.40
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $23.40
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.50
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $86.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.10
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $12.50
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $60.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $23.70
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $7.80
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $60.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.40
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $16.90
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.90
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $16.90
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $7.90
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $44.10

PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $173.00
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00
NOTE PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.	NOTE
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $279.00

Seats
Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86
Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86
Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57
Tie-On Seat Cover - Grey and Red 19". Deluxe cover with 2 inches of foam padding. Does not fit all tractors, must have a pan type seat only. (Item #: 178995, Ref: R2599) $43.80
Tie-On Seat Cover - Red and White, 21" wide. Deluxe with 2 inches of foam. (Item #: 178155, Ref: R1015) $39.00
Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $103.00

Sheet Metal / Body Parts
Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19
Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $178.00

Steering
Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn Power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003) $417.87
Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: 133205R91 (Item #: 111126, Ref: AE33538A) $12.60
Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $48.40

Wheels
Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. Replaces: 364343R92 (Item #: 103768, Ref: FW60166) $92.00
Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. (Item #: 116854, Ref: FW55166) $70.00
Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $44.10
Tire, Three Rib - Front tire, 3 Rib, 5.50 inches x 16 inches. Designed to be used with tube (part number WHS050). 6 Ply. Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16) $109.00
Tire, Three Rib - Front tire, 3 Rib, 5.50 inch x 16 inch. Designed to be used with tube (part number WHS050). 6 Ply. Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16) $109.00
Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $18.30
No Picture Tire Tube 24 Inch - This 24 inch tire tube is used for all tractors with the following tires: 10.00 x 24, 11.00 x 24, 11.2 x 24, and 12.4 x 24. (Item #: 178957, Ref: WHS059) $56.00
No Picture Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $64.00
No Picture Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 12.00 x 28, 13.00 x 28, 13.6 x 28, and 14.9 x 28. (Item #: 178895, Ref: WHS061) $116.00
No Picture Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $66.00
Categories All 500 Parts

Hat
IH Red Hat with Black Brim - With black brim and IH logo. (Item #: 183945) $14.99
IH Solid Red Hat - With IH logo. (Item #: 184041) $14.99