International Harvester / Farmall 600 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Pedal Shaft Seal - This Seal is used as a brake pedal shaft seal, (2 used per tractor) on Farmall / International: W9, WD9, WR9, Super WDR9, Super WD9, WDR9, WR9S, 600, 650, Super W9, Super WR9S. It measures 1.375 inch inside diameter, 2.130 inch outside diameter, and 0.437 inch wide. Replaces 0511073, 1K1590, 1K1590, 224810, 230608, 241779, 340214, 35451D, 357970R91, 357976R91, 380184R91, 43509D, 43509DA, 511073, 527829R91, 60454D, 659124R91, 70224810, 70230608, 70241779, 70241D, 938294R91, 938294R92, AH14076, AL2094T, AL56820, AM253T, AN30648, AN32717, AP24021, K1590, K1590, M86688, N71730N, T22069 (Item #: 128541, Ref: 70241779) $7.70

Clutch
Bearing - Pilot - New Pilot Bearing. 25mm (.9843 inch) inside diameter, 52mm (2.0472 inch) outside diameter with seals on both sides. For tractors: 400, 450, 500, 560, 600, 660, H, HV, M, M500, MD, MDV, MV, Super H, Super M, Super MD, Super MTA, Super W4, Super W6, W4, W6, WD6. (Item #: 100023, Ref: ST544) $5.40
Clutch Disc - 12 inch, 4 button, spring loaded, 1.1875 inch spline diameter, 11 spline. For tractor models 2706, 2756, 2806, 2826, 2856, 3088, 3288, 3688, 400, 450, 500, 560, 600, 660, 706, 756, 766, 786, 806, 826, 856, 886, 966, 986, Super MTA. (Item #: 112266, Ref: 384395R94) $154.00
Pressure Plate - Pressure Plate, 12 inch, 12 spring, 3 levers adjust on pivot point, 1.750 inch spline diameter, 17 spline. Flywheel step, 1.406 inch. For tractor models 400, 450, 500, 560, 600, 660, Super MTA. Replaces: 359121R97, 359121R96, 359121R95, 359121R94, 359121R93, 359121R92, 359121R91, 360079R94, 360079R93, 360079R91, 359041R93, 360080R91. (Item #: 166108, Ref: 359121R98) $459.00

Cooling System
Radiator Cap - 4 pound Pressure Cap. For tractor models 100, 140, 200, 230, 300, 330, 350, 400, 450, B450, 460, 560, 600, 650, 660. Replaces: 361705R91, 370871R91, 362323R91. Not for short filler neck. (Item #: 108081, Ref: D25826) $10.00
Radiator Cap Pressurized - For International / Farmall tractor models 100, 130, 140 (s/n 13967-earlier), 200, 230, 240, 330, 340, 460, 560, 600, 650, 660, Replaces International OEM number 393229R91, 362323R91, 370871R91, 2.050 radiator neck I.D.. Measure radiator neck before ordering, 7 PSI, (Item #: 112332) $7.98
Water Block Drain Plug, Winged - Plug 3/8 inch pipe thread, has "IH" and part number stamped in it, cast iron with zinc plating. For tractor models A, AV, Super A, Super AV, Super A1, Super AV1, B, BN, C, H, HV, Super H, Super HV, I4, I6, ID6, I9, ID9, M, MD, MV, MDV, Super M, Super MD, Super MV, Super MDV, MTA, 04, 0S4, 06, 0S6, ODS6, T6, T340, TD6, T9, TD9, W400, W450, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650 (Gas/Diesel), serviceable for Cub, Cub Lo-Boy. (Item #: 178066, Ref: 45314DC) $12.70

Drive Train
Gear Shift Knob - For Cub, Cub Lo-Boy, A, Super A, Super AV, B, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, W4, W6, WD6, Super W6, W9, WD9, Super WD9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 354, 400, 404, 450, 424, 460, 504, 560, 600, 606, 660, and on the hydraulic lever control on the 454 and 574. Gear shift lever knob. Replaces 3121549R1, IHS266. (Item #: 109514, Ref: 53717DA) $5.90

Electrical System
Distributor - Original IHC design comes with a 32 tooth drive gear. For tractor models Super W6TA, Super W9, Super WD6, Super WD6-TA, Super WD9, Super WDR9, W4, W400, W450, W6, W9, WD6, WD9, WDR9, WR9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 504, 600, 650, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 3514. R6332. MHSK1 (Item #: 124839, Ref: 107304C91) $120.00
Distributor - New and complete distributor comes with a 32 tooth gear, and is for tractor models: A, AV, B, BN, C, H, HV, M, MV, Super A, Super AV, Super C, Super H, Super M, Super MTA and other IH equipment with International Distributors. Replaces: 107296C91, 107299C91, 107302C91, 107304C91, 353890R91, Distributor Housing Casting Number: 353898R11, 354900R91, 357935R91, 362473R91, 362722R91, 364653R91, 364696R92, 366928R91, 372712R91, 380622R91. Uses IH points (included). (Item #: 124839, Ref: 107304C91) $120.00
Distributor Cap Spring Clip - Fits listed IH models when equipped with IH brand distributor 353898R11. Replaces: 107384C1, 353894R1 (Item #: 178117, Ref: 353894R1) $16.80
Distributor Drive Housing - This is a new distributor drive housing with an opening for tachometer drive. It is used to change from a magneto to a distributor or to add a tachometer drive to your tractor. The tachometer drive parts (tachometer drive assembly part number 369695R1, tachometer cable connector housing part number 369692R1 and 363817R1, connection housing plate) or tach. Drive blockoff plate are sold separately. NOTE: Will also work on tractors without tach drive by ordering number 363764R1 block off plate. Use with 107304C91 distributor when replacing a magneto. fits tractor models A, A1, AV, AV-1, B, BN, C, Cub, Cub Lo-Boy, H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W9, W4, W6, W6TA, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 2504, 300, 330, 340, 3444, 350, 3514, 404, 424, 444, 504, 400, 600, 650 450. Replaces: 363749R91, 363763R11. (Item #: 178938, Ref: 363749R91) $108.00
Distributor Dust Cover - Used with horizontal IHC distributor 353898R11 or J4 magneto on Models: 424, 444, 450, W450, 460, 504, 560, 600, 606, 650, 656, 660, 706, 756, 806, 826, 856, 3514, 3616. Replaces 384831R91. (Item #: 107074, Ref: 353900R11) $16.10
Distributor Gear - This Distributor Gear has 32 teeth. It is used on IH Distributor 353898R11. Replaces original part numbers 353902R1, 531461R91 (Item #: 111179, Ref: 353902R1) $29.00
Distributor Hold Down Clamp - For 5/16 inch hold down bolt and IH built distributor. 2 used per engine, sold individually. Fits fits tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, H, HV, Hydro 70, Hydro 86, I4, I6, I9, ID6, ID9, M, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, W4, W6, W9, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 2505B, 2510B, 2514B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 574, 600, 606, 650, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856. All with IH distributors. Replaces 341139R1, 353937R1. (Item #: 182464, Ref: 341139R1) $9.20
Distributor Tach Drive Housing Block Off Plate - This new Distributor Tachometer Drive Housing Block Off Plate with Gasket is used with part number 363749R91 when a Tachometer is not used. Fits tractor models Cub, Cub Lo-Boy, 130, 140, 230, 240, 2404, 300, 330, 400, 404, 450, 600, 650, 2424, 2444, 340, 424, 444, 2504, 350, 504. Replaces 363764R1, 363765R1. (Item #: 150708, Ref: 363764R1) $9.40
Distributor Terminal Screw - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a zinc plated Terminal Screw. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. Replaces International part number 353907R1 (Item #: 118472, Ref: 353907R1) $7.70
Distributor Terminal Screw Insulator - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a spring anchor terminal insulator. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. (Item #: 118473, Ref: 353906R1) $7.20
Distributor with base and tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, M, Super A, Super C, Super H, Super M, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2424, 2504, With tachometer drive and with base, Includes new distributor cap, points, condenser, 6V coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203589) $350.01
Distributor with base and tach drive, Used - For International tractor models A, B, C, Cub, H, M, Super A, Super C, Super H, Super M, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2424, 2504, With tachometer drive and with base, Includes new distributor cap, points, condenser., Does Not Include Coil, For a Remanufactured version of this part use Item #: 203589, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 403589) $291.01
Distributor with base less tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2404, 2424, 2444, 2504, 3444, 3514, Compatible with International Combine (s) 105, 203, Compatible with International Construction and industrial models T6, T340, 500, Without tachometer drive and with base, Includes new distributor cap, points, condenser, 6V Coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203588) $235.01
Electronic Ignition Conversion Kit - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 6 volt POSITIVE ground system only. Use with distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650 (Item #: 105084, Ref: 1442P6) $195.00
Electronic Ignition Conversion Kit - 12V Negative Ground - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 12 volt NEGATIVE ground system only. Use with IH distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650. Verify distributor number before ordering. (Item #: 105083, Ref: 1442) $164.00
Generator, Delco Type, 12 Volt - For tractor models 140, 214, 220, 37, 404, 420, 424, 450, 460, 504, 560, 600, 606, 660, 700, 770, 780, 806, 2404, 2424, 2504, 2606, Cub, Lo-Boy, T6, TD6, TD9, Power Unit. Replaces Delco numbers 1100305, 1100335, 1100363, 1100364, 1100369, 1100394, 1100401, 1100409, 1100426, 1100424. Remanufactured. Refundable $25.00 core charge will be added to your order. (Item #: 203181, Ref: TG-59) $370.72
Generator Pulley - This 2 piece adjustable pulley is used on gas or LP; with generator #'s 1101355, 1101423, 1100501, 1100997. The pulley measures 4.129 inch Diameter. Made with ductile iron. Includes set screw and lock nut. Used on: H, M, I4, I6, I9, HV, MV, W6TA, W9, O4, WR9, O6, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, W4, W6, WR9S, 300 (Farmall) up to SN 11002, 300 (Industrial) up to SN 2689, 400 (Farmall) up to SN 13458, 600, 650. Replaces 6745D, 6745DA, 6746D, 6746DA (Item #: 125677, Ref: 6745D) $53.57
H4 Magneto Pinion Driven Gear - This gear has 24 teeth and measures: 0.380 inch inside diameter, 0.759 inch outside diameter, 1.075 inch gear outside diameter, 0.952 inch overall height. It is used on H4 Magnetos. (Item #: 183878, Ref: 49420DX) $26.20
Key Switch, 2 Terminal - With keys. For tractor models (Cub serial number 224401 to 239826 with battery ignition), (Cub Lo-Boy from serial number 18701 and up with battery ignition), Cub Cadet 100, 100, (140 serial number 26801 to 45000), 240, 330, 340, 350, 404, 2404, 424, 2424, 444, 2444, 450, W450, 460, 504, 544, 560, 606, 650, 656, 600, 664, 666, 686, 706, 756, 766, 806, 826, 856, 966, 1026, 1066, 1206, 1256, 1456, 1466, 1468, 1566, 1568, Hydro 70, Hydro 86, Hydro 100. Replaces 370375R91, 379594R92, 403562R2. (Item #: 113393, Ref: 366313R91) $14.00
Magneto - This is a New Wico Magneto used on Farmall / IH Models: A, AV, B, BN, C, H, HV, I9, M, MTA, MTAV, MV, O4, O6, OS6, Super A, Super C, Super H, Super M, W4, W6, W6TA, 100, 130, 200, 230, 300, 350, 400, 450, 600, 650. It is also used on some industrials and power units. (Item #: 180178, Ref: XH1344) $567.00
Magneto Gasket Set - This magneto gasket set is for H4 Magnetos. It contains; Coil cover gasket 47453D, Distributor body gasket 47408D, Distributor gear cover gasket 49419D, Condenser hole cover gasket 359966R1 (48472DA), Magneto mounting gasket 55780DE (55780DD). Replaces: 359966R1, 47408D, 47453D, 48472DA, 49419D, 55780DD, 55780DE, E4226. For tractor models A, AV, B, BN, C, H, HV, I4, I6, I9, M, MTA, MV, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, T4, T5, T6, T9, U2, U2A, U4, U6, U9, W4, W6, W6TA, W9, WR9, WR9S, 100, 130, 200, 230, 300, 350, 400, 450, 600, 650, 400, 450 (Item #: 111272, Ref: MGK103) $10.00
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.90
Starter Drive Housing - This Starter Nose Cone is used on Delco starter numbers 1107021, 1107060, 1107067, 1107093, 1107174, 1107427, 1107448, 1108096. Bushing is included. This part replaces Delco part numbers 1878661, 1887109, 1910093, 1943759 (Item #: 179382, Ref: 1878661) $75.01
Terminal Clip - Light terminal plate with screws. For 200, 230, 300, 330, 350, 400, 450, 600, 650, A, B, C, H, HV, M, MD, O4, O6, ODS6, OS4, OS6, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super WD9, Super WDR9, Super A, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S (Item #: 117534, Ref: 79407H) $6.50

Engine Gaskets
Crank Seal, Front - This front crankshaft oil seal has a 2.625 inch Inside Diameter, a 3.38 inch Outside Diameter and is .475 inch wide. It Fits: I6, I9, ID6, ID9, M, MD, MDV, MV, O6, ODS6, OS6, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, T6, T6-61, T9, TD6, TD6-61, TD9, TD9-91, W400, W450, W6, W9, WR9, WR9S, 400, 450, 600, 650, B-450, BM, BMD, SBMD, Super BM. Replaces: 258511R91, 357972R91, 357977R91, 358511R91, 53872D, 410708 (Item #: 106640, Ref: 357972R1) $13.60

Engine Parts
No Picture Connecting Rod Bolt Lock Tab - For Diesel models: I9, ID6, MD, MDV, ODS6, Super MD, Super MDV, Super MDV-TA, Super MTA, 400, 450, Super W9, T9, TD6, TD9, W9, WD6, WR9, WR95. GAS and LP: 600, 650. (Item #: 167084, Ref: 253220R1) $7.70
No Picture Cylinder Head, Remanufactured, 260692R - For International / Farmall tractor models 600, 650 (Diesel), Replaces International Casting number 260692R, Cylinders 4, Casting Number 260692R, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200210) $1325.01
No Picture Cylinder Head, Remanufactured, 8320D - For International / Farmall tractor models Super W9, W9 (Gas), 600, 650, Replaces International Casting number 8320D, Casting No. 8320D, Engines 350, Cylinders: 4, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 205493) $1450.01
No Picture Cylinder Head, Remanufactured, 9195D - For International / Farmall tractor models Super W9, W9 (Gas), 600, 650, Replaces International Casting number 9195D, Engine 350, Cylinders 4, Casting No. 9195D, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200193) $288.01
Governor Spring - This Internal Governor Spring is 2.700 inches overall length with 0.110 inch wire diameter. It fits H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super MV, T6, T9, W4 Through 9 Series, W6, W6TA, W9, WR9, WR9S, 300, 350, 400, 450, 600, 650, Wheatland: 400, 450. It replaces original part numbers 357012R1 and 49407DBX. (Item #: 179313, Ref: 49407DBX) $11.60
Governor Thrust Bearing - Bearing has a outer diameter of 1.575 inches, width of 0.472 of an inch, and an inner diameter of 0.510 of an inch. The lip has an outside diameter of 0.750 of an inch, the shaft has an diameter of 0.656 of an inch, and has 2 pin holes with an inner diameter measuring 0.186 of an inch. For the following models: H, HV, Super H, Super HV, M (gas), Super M (gas), Super MTA (gas), O4, O6, OS4, OS6, Super W4, W4, Super W6 (gas), Super W6TA (gas), W6 (gas), W9 (gas), WR9S (gas), B-275 (gas), B-276 (gas), 300, 350 (gas), 354 (gas), 400, W400, 444 (gas), 450 (gas), W450 (gas), 600 (gas), 650 (gas). Replaces 48250D, 48250DX, and ST506. (Item #: 183913, Ref: 351910R91) $80.35

Engine Rings
Piston Ring Set - Standard - 4 Cylinder - For International / Farmall tractor models 600, 650, Compatible with International Engine (s) C350 (gas), Bore: 4.500", Compression Rings per Piston: (3) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .094", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .250", 4th Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a complete 4 cylinder set, (Item #: 129013) $421.00

Exhaust System
Muffler - Vertical muffler for gas tractors, fits engines C335, and C350. Inlet inside diameter 3-1/8 inch, outlet outside diameter 3 inch, length 22 inches, diameter 6 inches, round body type. For tractors W9, WR9, 600, 650. For 600, 650, Super WD9, Super WDR9, W9, WD9, WDR9, WR9. (Item #: 100809, Ref: 264116R92) $72.00
Muffler - For W9 gas, WD9 diesel, T9 gas, TD9 and TD14 diesel. Also for International 600 and 650 with C-350 gas and D-350 diesel engines. Muffler is vertical, inlet inside diameter 3-1/8 inch, outlet outside diameter 3 inch, length is 22 inches. Replaces OEM number 303973R91. (Item #: 100809, Ref: R1646) $72.00

Fuel System / Air Intake
Air Cleaner Bowl - Clear plastic pre-cleaner bowl for the air intake system. Bowl outside diameter at top approximately 7-1/4 inch, side height 3 inches, cone inside diameter at top 3-1/2 inch, overall height 4-1/8 inch. Commonly used on pipe inlets ranging from 2-3 inches. For tractors: M, MD, WR9S, Super WD9, 400, 450, W400, W450, 460, 504, 544 diesel, 455 diesel, 2544 diesel, 5606, Gas powered combines: 403 and 453 Hillside, 503, 615, 715. Can replace Donaldson P02-0227, also replaces 101965A, 10P871, 1125804, 1508881M1, 3119347, 365413R1, 71125804, 73186, 73533, 80073533, C0NN9A663A, F3446R, L60631, R28794 (Item #: 157279, Ref: R28794) $7.80
Carburetor Drain Trough - This Carburetor Drain Trough is used on tractors with F8 starting diesel carburetors. Replaces 58843DX. (Item #: 180176, Ref: 58843DX) $65.00
Carburetor Float - Float. For Updraft International Carburetors with throat size 1-1/4 inch or 1-3/8 inch. Dimensions: 2 3/16 inch length x 1 3/16 inch height, outside diameter 3 1/2 inches. For 2606, 2706, 300, 350, 400, 450, 460, 560, 600, 606, 650, 660, 706, M, MV, O6, OS6, Super H, Super HV, Super M, Super MTA, Super W6, Super W6TA, W400, W450, W6, W9, WR9, WR9S. (Item #: 107990, Ref: 47398DX) $19.00
Carburetor Float Valve Assembly - This is a new Carburetor Float Valve Assembly with stainless steel needle. It us used on F8 Diesel Starting Carburetors (53873DH, 67860DCM). (Item #: 179312, Ref: 32581DXB) $69.00
Carburetor Gasket Set - This Gasket Set is used on F8 Diesel Starting Carburetors (53873DH, 67860DCM). Contains 32606DD, 53459DA (Item #: 160212, Ref: IHS997) $10.98
Carburetor Kit, Comprehensive - This Comprehensive Carburetor Kit is for International Carburetor number 372723R93. It contains all the parts shown. (Item #: R7865) $68.31
Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: 356948R91. For the following tractor models: M, MTA, 600, W9. Add $125.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203308, Ref: 1414-CARB) $265.01
Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: 47387DB, 47387DC, 50983DB. For the following tractor models: HM, MTA, 600, W9. Add $125.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203308, Ref: 1415-CARB) $265.01
Diesel Fuel Filter - Fuel filter element, cartridge type, final. Comes with a gasket. For tractor models 400, 450, 600, 650, MD, ODS6, Super MD, Super WD9, W400, W450, WD6, WD9. (Item #: 182548, Ref: 259479R92) $80.00
Fuel Cap - 1 15/16 inch overall outside diameter fits many: 240, 300, 350, 400, 450, 600, 650, H, HV, M, MD, MDV, O4, O6, ODS6, OS4, OS6, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super W6, Super WD6, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S. (Item #: 116503, Ref: 40756D) $3.98
Fuel Pipe Coupling Nut - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, F12, F14, H, HV, I4, I6, I9, M, MD, MTA, O4, O6, Super A, Super C, Super H, Super M, Super W4, TD6, TD9, W4, W6, W12, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 444, 450, 460, 504, 560, 600, 606, 650, 656, 660, 686, 706, 756, 806, 826, 856, 2444, 3514, 3616, Compatible with International Combine (s) 303, 403, 503, 615, 715, Replaces International OEM number 29899D, 700155R11, 700153R11, 1/2"-20 Hi-duty tube fitting, 5/16" O.D., (Item #: 112642) $3.47
Sediment Bowl Assembly - Fuel Strainer assembly with 2.25 inch bowl, 1/8 inch pipe thread to fuel line, 3/8 inch pipe to tank for gasoline tractors: H, HV, M, Super M and MTA, O4, OS4, W4, 460, 560, 600, 650, 656, 660, 706, 756, 766, 806, 826, 856. Replacement bowl available as part S.65504. Replaces OEM numbers 358245R91 and 370832R91. (Item #: 105393, Ref: S.61581) $22.00

Gauges
Oil Pressure Gauge - For International / Farmall tractor models 350 (Diesel), 400 (Diesel), 450 (Diesel), 460 (Gas, LP, Diesel), 560 (Gas, LP, Diesel), 600 (Diesel), 650 (Diesel), 660 (Gas, LP, Diesel), Compatible with International Combine (s) 105, 453, 615, 715, Compatible with International Construction and industrial models 3616 (Gas and Diesel), 3800 (Gas and Diesel), 3850 (Gas and Diesel), Compatible with International Hay Cutting (s) 201, 210, 225, 230, 275, 375, Replaces International OEM number 362177R94, 393488R91, IH Logo on Face, Dash Mounted, 0-45 PSI, 1/8" male pipe threads, (Item #: 121661) $49.00
Tachometer Cable - For International / Farmall tractor models 600, 650, 666 (Diesel with D310 Engine), 766 (Diesel with gear Drive), 806 (Diesel with gear Drive), 856 (Diesel with gear Drive), 1026 (Diesel), 1206 (Diesel with gear Drive), 1256 (Diesel), 1256, 1456 (Diesel with gear Drive), 2856 (Diesel with gear Drive), 3088 (Diesel), 3288 (Diesel), 4166 (Diesel), 4186 (Diesel), 4366 (Diesel), 21026, 21256, 21456 (Diesel with gear Drive), Replaces International OEM number 384845R92, 387916R91, 393328R91, 393328R92, 393328R93, 341210C91, 89159R91, Length: 80", Load End:, Drive End:, Metal Sheath, 5/8 - 18 x 7/8 - 18 threads with square on both ends, For Nylon Sheath Cover use Item #: 115094, (Item #: 115095) $34.50
Tachometer Cable Connector - This new tachometer cable connector housing retainer clip (Thrust Stop) is used to retain part numbers 369695R1 (Tachometer Drive Assembly) and 369692R1 (Tachometer Cable Connector) into part number 363749R91 Distributor Housing Drive. Fits tractor models Cub, Cub Lo-Boy, 130, 140, 230, 240, 2404, 300, 330, 400, 404, 450, 600, 650, 2424, 2444, 340, 424, 444, 2504, 350, 504. Replaces: 369693R1. (Item #: 150712, Ref: 369693R1) $5.10
Tachometer Cable Connector Housing - This New Tachometer Cable Connector Housing is used with 369695R1 Nylon gear with metal shaft. Will also need to order tach drive gear 369695R1 and 369693R1 clip for 300, 330, 350, 400, 450, 600, and 650 if replacing ALL NYLON gear/shaft drive. Fits Cub, Cub Lo-Boy, 130, 140, 230, 240, 2404, 300, 330, 400, 404, 450, 600, 650, 2424, 2444, 340, 424, 444, 2504, 350, 504. Replaces 369692R1 (Item #: 150711, Ref: 369692R1) $55.00
Tachometer Connection Housing Plate - Tachometer Connection Housing Plate with gasket. Used with part number 363749R91 distributor housing. Fits tractor models Cub, Cub Lo-Boy, 130, 140, 230, 240, 2404, 300, 330, 400, 404, 450, 600, 650, 2424, 2444, 340, 424, 444, 2504, 350, 504. Replaces: Plate: 363817R1, Gasket: 363814R1, 363814R2. (Item #: 150709, Ref: 363817R1) $10.80
Tachometer Drive Assembly - This new Tachometer Drive Assembly is used with part number 363763R11 cast distributor mounting housing with provision for drive. Fits tractor models Cub, Cub Lo-Boy, 130, 140, 230, 240, 2404, 300, 330, 400, 404, 450, 600, 650, 2424, 2444, 340, 424, 444, 2504, 350, 504. For IH distributor systems only. This part does not replace all nylon style gear/shaft number 363816R1 that was original on 300, 330, 350, 400, 450, 600, 650, unless the connector housing part number 369692R1 is ordered along with the 369693R1 clip. Replaces: 369695R1, 369695R91. (Item #: 150710, Ref: 369695R1) $57.00

Hitch / Drawbar
Drawbar Pin Retainer Plate - Used on the following Farmall / International models: H, M, 560, 806, 1066, MD, MTA, W6TA, W9, O4, WD9, WR9, Super WDR9, OS4, Super H, Super M, Super MD, Super MTA, Hydro 84, Super W4, Super W6, Super W6TA, Super WD6, Super WD9, W4, W6, WD6, WDR9, WR9S, 300, 330, 340, 350, 400, 450, 454, 460, 464, 504, 544, 574, 600, 606, 650, 656, 660, 664, 666, 674, 706, 756, 766, 826, 284, 856, 966, 1026, 385, 484, 584, 684, 686, 784, 884, Super MDTA, Super WD6TA, Super WR9S, Super W9, WD6TA, this part measures 1.480 inches long, 1 inch wide and has a 0.377 inch hole diameter and 0.193 inch thick. Many of the listed models used a round plate rather than the rectangular one. This part will replace the round version. Replaces OEM numbers 132794H1, 491390, 49139D, 57654D, 57655D, 58657D (Item #: 112643, Ref: 49139D) $7.50

Hydraulic System
Hydraulic Manifold - Hydraulic Pump Flange, Hydraulic Manifold, Port Block is used on (M, Super M, 400, 450 Gas or Diesel), Super W6, Super W9, Super WD6, Super WD9, W6, W9, WD6, WD9, 600, 650. 3/4 inch NPT inlet and outlet. Threaded for hydraulic hose. Must use rubber hose lines. (Item #: 115188, Ref: IHS1240) $71.00
Hydraulic Pump - For block style lines that mount to bottom of pump. This is a cast aluminum style and will not directly replace cast iron style (it will replace if you have a plate manufactured to adapt the type of hose connections as is on your old pump). For tractor models Super M, Super MTA, Super W6, Super W9, 400, 450. All Gas with Live Hydraulics. Replaces 128190C91, 357214R92, 362175R94 (Item #: 102180, Ref: 128190C91) $623.00

Lights
Headlight Lens - Replacement Glass Lens is 4.75 inch outside diameter for IH (45640DB) Headlight Assemblies. Models: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650, A, B, C, Cub, Cub Lo-Boy, H, M, MD, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super W4, Super W6, W4, W6, W9, WD6, WD9. (Item #: 111330, Ref: GC200) $15.30
Headlight Trim Ring - Moulding trim ring for 5 inch teardrop headlights or rear lights on tractors (painted). For tractor models 100, 130, 140, 200, 230, 240, 300, 340, 350, 400, 450, 600, 650, A, AV, B, C, Cub, Cub Lo-Boy, H, HV, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super C, Super H, Super HV, Super M, Super MD, Super MTA, Super WD9, Super A, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S. (Item #: 112980, Ref: 53525DA) $19.85
Knob - Knob for combination rear light and tail light switch (used only with switch body with 15/32 inch shaft). For tractor models 100, 130, 200, 230, 300, 330, 340, 350, 400, 450, 600, 650, C, Cub, Cub Lo-Boy, H, HV, M, MD, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W6, Super WD9, Super A, WR9S. (Item #: 179762, Ref: 359773R91) $8.72
Light Clamp - Clamp, lamp assembly for tractors. For tractor models 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650, A, B, C, Cub, Cub Lo-Boy, H, M, MD, O4, O6, OS4, OS6, Super C, Super H, Super M, Super W6, Super A, W4, W6, W9, WD6, WD9. (Item #: 178025, Ref: 350920R1) $10.00

Miscellaneous
Gear Shift Boot - For International / Farmall tractor models I9, W9, 600, 650, Replaces International OEM number 61064D, Shaft 1.395" Hole, Base 2.160" Hole, Height: 4-1/8", (Item #: 126660) $44.00

Oil System
Oil Filter - Oil filter element, cartridge type with gasket. For gas engines: C248, C335, C350, in tractors: M and MV to serial number 59393, I6 and W6 to serial number 4242, W9, 600, 650. For diesel engines D248, D264, D281, D335, D350, tractors: MD, Super MD, ODS6, WD6, Super WD6, For 400, 4252, 450, 6, 600, 650, M, MD, MV, ODS6, Super MD, Super WD6, Super WD9, W6, W9, WD6, WD9. Filter is 3 7/8 inches in diameter and 7 inches overall length. Replaces: 376376R91, 257867R92, 360432R91, 63884D, 63885D. (Item #: 185572, Ref: 376376R91) $22.00
Oil Pan Drain Plug - White Zinc Finish, 7/8 inch - 18 UNF. Fits multiple models. Washer available as part number EBU6734A, not included. Replaces: 688067C1, 359875R1. (Item #: 126591, Ref: C5NE6730B) $8.10
Oil Pan Drain Plug Washer - This washer is used with C5NE6730B 7/8 inch Oil Drain Plug. (Item #: 140612, Ref: EBU6734A) $1.70

PTO / Driveline
PTO Seal - Measures 1.306 inch inside diameter, 2.220 inch outside diameter. THIS SEAL IS .312 InchES WIDE. VERIFY THE WIDTH OF YOUR OLD SEAL. YOU NEED TO INSTALL 2 OF THESE IF YOUR OLD SEAL IS WIDER. For tractor models Super A, H after serial number 118000, (M, MD, Super M, Super MTA and Super MD after serial number 59957), Late W4, W6, W9, Super W4, Super W6, Super W9, B250, B275, B414; Also fits the following models with transmission driven PTO (not Live PTO): MTA, 300, 330, 350, 354, 364, 384, 400, 424, 434, 444, 450, 454, 544, 600, 650, 2300, 3414, 3514, 3616. Replaces 3065217R91, 358772R91, 358812R91, 50702D, 372394R91, S90957, 708107R91. (Item #: 114730, Ref: 45702D) $9.80

Seats
No Picture Seat Custom with Fold Up Arms - Black vinyl assy. with fold up arm rests fits, 1030, 1031, 1032, 1070, 1175, 1190, 1200TK, 1290, 1390, 1470TK, 200, 230, 240, 2504, 300, 330, 340, 350, 400, 404, 450, 460, 480B, 503, 504, 560, 580B, 600, 606, 650, 660, 730, 740, 830, 840, 870, 930, 940. MUST USE ADAPTER FOR FOLLOWING MODELS, A, B, C, H, HV, M, MDV, MD, MV, Super H, Super A, Super M, W9, WD9, WDR9, WR9S. (USE ADAPTER # CSA300). (Item #: 101387, Ref: CS108-1V) $116.00
Seat Locator Spring - This Seat Locator Spring fits: C, Super C, (Super H, Super HV serial number 19234 and up), (Super M, Super MD, Super MDV, Super MTA, Super MV serial number 28175 and up) Super MTA (Diesel serial number 28175 and up), 200, 230, 400, 450, 560, 600, 650, 660, Farmall Rowcrop: 300, 350, 460, Wheatland: 400, 450; Replaces: 352105R1. (Item #: 115150, Ref: 352105R1) $8.58
Seat Pan - Steel Black vinyl without drain hole Fits tractor models, 100, 140, 200, 230, 240, 300, 340, 350, 460 DSL, 600, 650, A, AV, B, C, Cub, Cub Lo-Boy, H, HV, M, MD, MDV, MTD, MV, Super H, Super M, W9, WD9, WDR9, WR9S (Item #: 191059, Ref: 357518R92-1) $205.00
No Picture Seat Pan - Steel Silver vinyl Fits Models, 100, 140, 200, 230, 240, 300, 340, 350, 460 DSL, 600, 650, A, AV, B, C, H, HV, M, MD, MDV, MTD, MV, Super H, Super M, W9, WD9, WDR9, WR9S. (Item #: 101246, Ref: 357518R92-18) $148.00
Seat Pivot Support Rod - This Seat Pivot Support Rod is 3 1/2 inches in length. Includes machine washers, rubber bushings, bolts and lock washers. (Item #: 105343, Ref: 355753R1) $19.90
Seat Shock Bushing - This bushing is for the horizontal bolt hole. It measures 1.223 inches outside diameter at the largest point. The hole inside diameter is 0.597 inches. The length measures 0.724 inches overall. 2 to 4 used per shock. This part replaces 72696R1, 70222488, T19118, 230288, 250416R1, F3296R, R26832, 760674M1 (Item #: 109602, Ref: 72696R1) $2.30
Seat Spring - Cone Shape SPRING Measures 13 inches tall and 8.5 inches at base. For tractor models 200, 230, 300, 350, 400, 450, 460, 560, 600, 650, 660, C, H, HV, M, MD, MTA, Super C, Super H, Super M, Super MTA. Replaces IHS030. (Item #: 101283, Ref: 354670R2) $26.90

Sheet Metal / Body Parts
Battery Box - This restoration quality battery box comes with a lid and fits the following tractor models: I6, O6, OS6, Super W6, Super WD9, Super WDR9, W6, W9, WR9, 600 Diesel, and 650 Diesel. Please note that Diesel model tractors require 2. It measures: 7 3/16 inches x 11 3/4 inches inside, and is 9 1/8 inches tall. It replaces the part number 60700D. (Item #: 179384, Ref: 60700DR) $149.30
Battery Hold Down Rubber - The battery hold down rubber is3/4 inches tall, inserts into the retainers in the battery box lid. These are sold EACH. For tractor models Cub, Cub Lo-Boy, A, AV, B, (BN, C 51690D), AI, H, HV, M, MV, MD, MDV, W6, W9, WD6, Super A, Super C, Super H, Super HV, Super M, Super MTA, Super W6, 100, 130, 140, 200, 230, 600, 650. Replaces: 51690D. (Item #: 116587, Ref: R5103) $4.80
No Picture Grille Screen - For International / Farmall tractor models A, B, C, Cub (s/n 222500-earlier with round hood / grille), Cub Lo-Boy (s/n 17200-earlier with round hood / grille), H, HV, I4, I6, I9, M, MD, MTA, O4, O6, O9, OS4, OS6, Super A, Super C, Super H, Super HV, Super M, Super MTA, W4, W6, W9, 100, 130, 140 (s/n 23300-earlier), 200, 230, 240, 300, 330, 340, 350, 400, 450, 460, 560, 600, 650, 660, Size: 2' x 3' with 5 squares per inch, Wire Grille Screen Clips use Item #: 108001, Additional Handling and Oversize Fees Apply To This Item, (Item #: 112471) $23.10

Steering
Steering Wheel - For M, MD, W9, WD9, WR9, 400, 450, 600, 650. Steering Wheel 20 inches in diameter, 3/4 inch keyed hub, 4 spokes. (Item #: 101430, Ref: 557282R91) $43.60
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00
Steering Wheel Nut - Zinc Plated - For International / Farmall tractor models 300, 400, 600, 650, Replaces International OEM number 366285R1, 13/16" - 20 NEF Thread, Zinc Plated, (Item #: 126723) $11.10

Wheels
Front Wheel / Rim Clamp - Used on many Farmall / IH tractors, this clamp 1.485 inch over all length with a 0.540 inch hole. Three or more used per wheel. Sold individually. Replaces 48976DA (Item #: 152052, Ref: 48976DA) $13.00
Rubber Bushing Retainer - For International / Farmall tractor models A, B, C, Cub, H, I4, O4, Super A, Super C, Super H, Super M, Super W4, Super W6, Super W9, W4, W6, 100, 130, 140, 200, 230, 600, 650, Replaces International OEM number 50942D, (Item #: 126651) $3.80
No Picture Wheel Hub Ball Bearing - Ball bearing, for wheel hub. Planters: 56, 58, 66, 400 and 500 Cyclo, 600. Mfr. # 204KRNP2, For Planters: 56, 58, 66, 400 and 500 Cyclo, 600. (Item #: 112121, Ref: 465003R91) $7.10
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $365.01
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.87
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.10
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.60
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $4.90
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.80
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.50
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.10
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.10
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.80
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $4.90
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.00
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.40
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.40
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.30
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.60
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.00
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.10
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.30
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.30
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.40
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.60
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.90
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $11.20
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $18.60

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $94.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.50
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.90
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.20
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.80
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $27.00

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $78.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $108.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $176.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.80
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $11.00
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $12.70
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.10
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $28.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $59.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $39.90
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $45.20
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $14.90

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $367.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $440.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $440.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.28
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $25.70
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $14.70
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.60
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.60

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $120.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.70
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.80
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $98.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $45.00
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $42.00
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.70
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $42.00
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $390.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $119.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.40
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $68.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $54.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.30
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $55.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.90
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $58.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $23.30
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $9.40
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $23.30
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.50
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $86.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.10
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $12.50
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $60.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $23.70
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $7.80
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $60.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $16.90
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.90
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $16.90
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $7.90
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $44.10