International Harvester / Farmall 915 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Accessories / Supplies
Engine Block Heater - Frost plug heater with cord. 1250 watt, 120 volt, 1.240 inch diameter. Fits tractors and combines with diesel engines. Cord is 72 inches long. Fits diesel engines: D312, D360, D and DT414, D and DT436, D and DT466. For 1066, 1086, 1440, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3488, 3588, 3688, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 666, 6788, 686, 766, 815, 886, 915, 966, 986, HYDRO 100, HYDRO 186, HYDRO 70, HYDRO 86. (Item #: 164169, Ref: 71151C91) $90.00

Cooling System
Radiator - For tractor models 715, 815, 915, 1440 Combines. (Item #: 101723, Ref: R2773) $1119.01
Water Pump - Water pump with hub installed. Heavy duty replacement with 8 vane impeller. Excellent where low cooling capacity is a problem. For diesel engines: D312, D360, D and DT414, D and DT436, D and DT466. For 1066, 1086, 1440, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3488, 3588, 3688, 3788, 4166, 4186, 4366, 4386, 453, 5088, 5288, 5488, 6388, 6588, 666, 6788, 686, 7288, 7488, 766, 815, 886, 915, 966, 986, HYDRO 100, HYDRO 186, HYDRO 70, HYDRO 86. Replaces: 672644C95, 673162C93, 673162C94. (Item #: 100795, Ref: 673162C93) $110.00
Water Pump - Water pump with hub installed on 1 inch outside diameter shaft. The perfect replacement for O.E.M. pump with smaller 7/8 inch outside diameter shaft. For diesel engines: D and DT361, D and DT407, in tractors: 806, 1206, 2806, 21206, 856, 1026, 1256, 1456, 2856, 21026, 21256, 21456, 815 For 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. Replaces 701335C92, 701335C91. (Item #: 100794, Ref: 701335C92) $110.00

Electrical System
Alternator - Alternator, 12 volt, 61 amp, external regulator, 2 terminal 12 o-clock position. For 100, 1000, 105, 1066, 110, 1100, 1110, 115, 120, 1200, 1206, 1256, 1275, 1300, 1456, 1466, 1468, 200, 205, 210, 21206, 21256, 21456, 222, 225, 23, 230, 2444, 2544, 2606, 2656, 2706, 275, 2756, 2806, 2856, 3110, 315, 3410, 3444, 3514, 3516, 3616, 375, 3800, 3850, 403, 4100, 4300, 444, 503, 504, 544, 601, 602, 606, 616, 622, 656, 706, 756, 766, 806, 815, 856, 915, 966, HYDRO 100. (Item #: 113606, Ref: 1100883) $123.00
Alternator - 12 volt, 61 amp. For tractor models 580 Super D, 580 Super E, 580D, 2090, 2290, 2390, 2590, 2094, 2294, 2394, (2470 serial number 8762940 to 8825000 and 8826412 and up), 2590, 2594, 3294, (1070 serial number 8675001 and up), 1270, 1370, 1570, 2670, (970 serial number 8816812 to 8817164 and 8817283 and up), 480C, 480D, 480LL, 580C, 2500A, 464, 574, 674, 4166, 4186, 1086, 1486, 1586, 3388, 3588, 3788, 4366, 4386, 4568, 4586, 886, 986, 3088, 3288, 3688, 3688HC, 5088, 5288, 5488, (Cub serial number 248125 and up), Cub 184, Cub 184 Lo-Boy, Hydro 70, Hydro 86, 666, 686, (815, 915 serial number 8001 and up), Hydro 186, Hydro 3488, 786. Replaces A46932, A46938, A47044, A47057, A47623, A47625, TY6600, 1102920, 1103160, 1103184, 1105164, 1105178, 1105514, 1105574, 20-7101161. (Item #: 110572, Ref: ADR0133) $116.00
Alternator - 12 volt, 55 amp. For tractor models (105, 205 1968 to 1970 with 153 gas), (315 1968 to 1970 with BD-331), (403 1968 to 1970 with 301 diesel/263 gas), (503 1968 to 1969 with 282 gas/301 diesel), (615 1971 with 263 gas). Replaces 1100805, 1100883, 1100791, 1100778, 1100720. (Item #: 113606, Ref: ADR0231) $123.00
Alternator - 12 volt, 72 amp. For tractor models (453 1975-79 with 301 gas), (453D 1975-79 with 360 dsl), (715 1975-79 with 301 gas), (715D 1975-79 with 310 dsl), (815 1971-74 with V304 gas/V345 LPG), (815D 1971-79 with 414 dsl), (915 1971-74 with V392 gas/345 gas ot LPG), (1420 1978-86 with 358 dsl), (1430D 1980-84 with 358 dsl), (1440D 1974-86 with 436 dsl), (1460D 1977-86 with 436 dsl), (1480 1977-79 with 466 dsl), (666D 1972-76 with 312 dsl), (Hydro 70D 1973-76 with 312 dsl), (Hydro 100D 1973-76 with 436 dsl), (Hydro 186D 1976-81), (Hydro 686 1976-80 with 291 gas), (Hydro 686D 1976-80), (140, 140HC 1975-79 with 123 gas), (464 1975-78 with 175 gas), (464D 1977-78 with 179 dsl), (574 1975-78 with 200 gas), (574D 1977-78 with 239 dsl), (674, 674RC 1978-84 with 200 gas), (674D, 674DRC 1978-84 with 239 dsl), (686 1976-80 with 291 gas), (686D 1976-80 with 312 dsl), (766D 1971-76 with 360 dsl), (886D 1976-81 with 360 dsl), (966D 1971-76 with 414 dsl). Replaces 1102921, 1102922, 1100587, 1105573. (Item #: 110572, Ref: ADR0133) $116.00
Blower Motor - This Blower Motor is 4 wire, 12 volt 3/8 inch x 4 1/4 inch shaft, 3 speed, body length 4 1/8 inches, body diameter 3 1/2 inches. It is used on Tractors: 656, 706, 756, 766, 786, 806, 856, 886, 966, 986, 1066, 1086, 1466, 1468, 1486, 1566, 1568, 1586, 2656, 2706, 2756, 2806, 2856, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 4568, 4586, 4786, Hydro 100, Hydro 186. Combine: 715, 815, 915, 1420, 1440, 1460, 1470, 1480. Windrower: 4000, 5000, 5500, 8830. Replaces 539053R3, 539053R2, 539053R1, 1987442C1, 1987399C3, 175577C2, 175577C1. (Item #: 108656, Ref: 72162089) $74.00
Key Switch, 2 Terminal - With keys. For tractor models 3444, 3514, 3616, 4100, 4156, 4166, 4186, 4366, 4386, 615, 715, 815, 915. Replaces 370375R91, 379594R92, 403562R2. (Item #: 113393, Ref: 366313R91) $14.30
Key Switch, 5 Terminal - 3 position, with keys. For tractor models 1086, 464, 574, 674, 786, 886, 986, 1486, 1586, 2500A, 3388, 3588, 3788, 4386, 4568, 4586, 4786, Hydro 186, 715, 815, 915, 1440, 1460, 1480. (Item #: 155916, Ref: 107682C1) $38.60
Starter Drive - Replaces; 1877350, 1948877, 1933838, 800965. For tractor models 1026, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, 21206, 21456, 21256, 2706, 2756, 2806, 2826, 2856, 3088, 3288, 3388, 350, 3588, 3688, 3788, 4166, 4186, 450, 560, 6388, 6588, 660, 6788, 706, 756, 766, 786, 806, 815, 826, 856, 886, 915, 966, 986, Hydro 100, Hydro 186, Hydro 3488. With spiral shaft. (Item #: 117546, Ref: 1651487C1) $33.90
No Picture Starter, Rebuilt - A rebuilt Delco start that is 12 volts, counter clockwise rotation and has a 10 tooth starter drive for (544, 2544, 656, 2656, all Gas with ST, 1967 to 1973), (3514, 3616 Gas 1967 to 1973), (504, 3514 Gas 1969 to 1974), (C-200, 263 Gas 1968 to 1970), (3514 with C-173 Engine with ST 1969 to 1970), (915 Gas Combines 1969 to 1974), (666 with ST 1972 to 1974), (F-686 AG Tractor 1977 to 1979), (706 Gas 1967 to 1968), (766 Gas 1967 to 1968). REBUILT Starter. 12 Volt). Replaces 1108343. (Item #: 203453, Ref: TS-1230) $359.57

Engine Bearings
No Picture Cam Bearing Set - CAM BEARING SET. For 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. (Item #: 106673, Ref: CBK-H361) $64.00
Cam Bearing Set - Camshaft bearing kit for six cylinder diesel engine. For tractor models 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. (Item #: CBK-H414) $42.50
No Picture Camshaft Bearing Set - For tractor models 806, 2806. (D361 CID Diesel 6-cylinder engine. Cupped head piston) and models 1206, 21206. (D361 CID Turbo Diesel 6-cylinder engine. Cupped head piston). If other than standard, specify size in comments. (.010, .020) (Item #: 106673, Ref: CBK-H361) $64.00
No Picture Main Bearing Set - For 966 Tractor and 815 Combines. (DT414 CID Diesel 6-cylinder engine. Cupped head piston) and 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cylinder engine. Cupped head piston) and 1466, 1486, 1566, 1586, 3388, 4166, 4186, 5088, 6388 and 1460, 1480 Combines. (DT436 CID DT436B Turbo Diesel 6-cylinder engine. Cupped head piston). (Item #: 106628, Ref: MBK414) $98.00
No Picture Main Bearing Set, .010 - Main bearing set. For tractor models 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. (Item #: 106625, Ref: MBK-H361D-010) $143.00
No Picture Main Bearing Set, Standard - Main bearing set. For tractor models 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915 (Item #: 106624, Ref: MBK-H361D) $230.00
Rod Bearing Set - ROD Bearing SET For 1026, 1066, 1086, 1206, 1256, 1456, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 21026, 21206, 21256, 21456, 2806, 2856, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 806, 815, 856, 915, 966 (Item #: CRK-H361D) $105.09
No Picture Rod Bearing Set, .010 - Rod bearing set. For tractor models 1026, 1066, 1086, 1206, 1256, 1456, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 21026, 21206, 21256, 21456, 2806, 2856, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 806, 815, 856, 915, 966. (Item #: CRK-H361D-010) $69.23
No Picture Rod Bearing Set, .020 - Rod bearing set. For tractor models 1026, 1066, 1086, 1206, 1256, 1456, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 21026, 21206, 21256, 21456, 2806, 2856, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 806, 815, 856, 915, 966. (Item #: CRK-H361D-020) $95.18

Engine Gaskets
Front Crank Seal - FRONT CRANK SEAL. For 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. (Item #: 106648, Ref: 606780C93) $24.60
Front Crank Seal - This front crankshaft oil seal has a 3 inch Inside Diameter, a 4 inch Outside Diameter and is .5 inch wide. It Fits: 1440, 1460, 1470, 1480, 1640, 1660, 1680, 453, 815, 915, 1822 (diesels up to SN: JJC0012690), 1844 (diesels up to SN: JJ0002462), 515, H60E, H65C, S10, S8A, S9B, Hydro 100, Hydro 186, Hydro 70, Hydro 86, 1066, 1086, 1466, 1486, 1566, 1586, 3388, 3488, 3588, 3688, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 666, 6788, 686, 7288, 7488, 766, 966, 986, 886, E200, E412, E412B. Replaces: 690437C91 (Item #: 106647, Ref: 690437C91) $12.98
No Picture Gasket set - Complete Gasket Set. For tractor models 856, 2856 Tractors and 815 Combines with D407 and 1026, 1256, 21026, 21256 Tractors with DT 407. (D 407 CID and DT407 CID Turbo Diesel 6-cylinder engine. Cupped head piston. Piston pin diameter 1-1/2 inch) and for 1456, 21456 Tractors and 915 Combines with DT407. (DT407 CID and DT407 CID Turbo Diesel 6-cylinder engine. Cupped head piston. Piston pin diameter 1-5/8 inch). (Item #: 131549, Ref: GK3857) $559.00
No Picture Gasket Set - Complete Gasket Set including crankshaft seals for 414/436/466 CID Diesel engines in: 966 Tractor and 815 Combines. (DT414 CID Diesel 6-cylinder engine. Cupped head piston) and for 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cylinder engine. Cupped head piston) and 1466, 1486, 1566, 1586, 3388, 4166, 4186, 5088, 6388 and 1460, 1480 Combines (DT436 CID), 4366, (4386 to engine serial number 74999). (Item #: GK414) $310.60
No Picture Lower Gasket Set - For tractor models 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. (Item #: 106730, Ref: CS414) $106.00
Oil Pan Gasket - For tractor models 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. Due to the size of this gasket, (Item #: 106710, Ref: 671827C1) $26.70
Oil Pan Gasket - For tractor models 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. Replaces 328731R1, 341297, AV101876. Due to the package size require to ship this gasket, $15 addtional will be added. This will be included as part of the shipping total on your order. (Item #: 106709, Ref: OPG345287R94) $35.20
Rear Crank Seal - For tractor models 1026, 1066, 1086, 1206, 1256, 1456, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 21026, 21206, 21256, 21456, 2806, 2856, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 806, 815, 856, 915, 966. (Item #: 106660, Ref: 691631C91) $29.98
No Picture Rear Crankshaft Seal - For tractor models 1026, 1066, 1086, 1206, 1256, 1456, 1460, 1466, 1480, 1486, 1566, 1586, 21026, 21206, 21256, 21456, 2806, 2856, 3388, 4166, 4186, 5088, 6388, 766, 806, 815, 856, 915, 966 (Item #: 106660, Ref: 1809964C92) $29.98
No Picture Upper Gasket Set - Valve Grind Gasket Set for 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. Contains all gaskets necessary for doing a valve job, (including head gasket). (Item #: 106695, Ref: HS414) $110.00

Engine Rebuild Kits
No Picture Basic Engine Overhaul Kit, Less Bearings - For 1456, 21456 Tractors and 915 Combines with DT407. (DT407 CID and DT407 CID Turbo Diesel 6-cyl eng. Cupped head piston. Piston Pin Diameter 1-5/8”) Kit contains sleeves and sleeve seals, pistons and piston rings, pins and retainers, complete gasket set with crankshaft seals. ENGINE BEARINGS ARE NOT INCLUDED. (Item #: 130622, Ref: BEKH1287-LCB) $824.00
Basic Engine Overhaul Kit, Less Bearings - For 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cylinder engine. Cupped head piston). Kit contains sleeves and sleeve seals, pistons and piston rings, pins and retainers, complete gasket set with crankshaft seals. ENGINE BEARINGS ARE NOT INCLUDED. (Item #: 130620, Ref: BEKHDT414-LCB) $1269.01
No Picture Basic In-Frame Engine Kit - For 1456, 21456 Tractors and 915 Combines with DT407. (DT407 CID Turbo Diesel 6-cylinder engine. Cupped head piston. Piston pin diameter 1-5/8 inch). Kit contains complete sleeve and piston kit with rings, pins and retainers, valve grind gasket set and pan gasket, rod bearings (available in standard, .010, .020, .030, .040), main bearings (available in standard, .010, .020, .030). Please specify bearing sizes in the comment section when placing an order on line. (Item #: BIFH1287) $1470.17
No Picture Basic In-Frame Engine Kit - For 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cylinder engine. Cupped head piston). Kit contains complete sleeve and piston kit with rings, pins and retainers, valve grind gasket set and pan gasket. (Item #: 189602, Ref: BIFHDT414) $860.00
No Picture Engine Overhaul Kit, Less Bearings - For 1456, 21456 Tractors and 915 Combines with DT407. (DT407 CID Turbo Diesel 6-cylinder engine. Cupped head piston. Piston pin diameter 1-5/8 inch). Kit contains sleeves and sleeve seals, pistons and piston rings, pins and retainers, pin bushings, complete gasket set with crankshaft seals, intake and exhaust valves, valve keys, guides and springs. ENGINE BEARINGS ARE NOT INCLUDED. IMPORTANT: Specify the part numbers on your old intake and exhaust valves to ensure that correct replacements are sent. (Item #: EOK1287-LCB) $2456.57
Engine Overhaul Kit, Less Bearings - For 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cylinder engine. Cupped head piston). Kit contains sleeves and sleeve seals, pistons and piston rings, pins and retainers, pin bushings, complete gasket set with crankshaft seals, intake and exhaust valves, valve keys, guides and springs. ENGINE BEARINGS ARE NOT INCLUDED. IMPORTANT: Specify the part numbers on your old intake and exhaust valves to ensure that correct replacements are sent. (Item #: EOKDT414-LCB) $1666.01
No Picture Valve Overhaul Kit - For tractor models 966, combine 815, 1066, 1086, combine 915, 1466, 1486, 1566, 1586, 3388, 4166, 4186, 5088, 6388, combine 1460, 1480, 4366, 4386, 3588, 3788, 4386, 5288, 5488, 6588, 6788, 7288, 7488, combine1470, 1480 (6 cylinder Diesel Turbo and Non-Turbo, D414, DT414, DT414B, DT436, DT436B, DT466, DT1466, DT466B, DT1466B, DT466C, DT1466C). Kit includes valves, valve springs, valve keys, valve guides. (Item #: VOKH414) $362.33

Engine Parts
Crankshaft Damper Pulley - This is a 3 spoke pulley/dampener. For tractor models 1066, 1086, 1440, 1460, 1480, 3488, 3588, 3688, 4166, 4186, 5088, 6588, 666, 686, 766, 815, 886, 915, 966, 986, Hydro 100, Hydro 186, Hydro 70, Hydro 86. All with DT-414, DT436, D-312 or D-360 engines. It measures: 10.203 inch outside diameter, 2.125 inch center hole and 2.61 inches wide. Replaces 680275C92. (Item #: 112099, Ref: 680275C92) $283.00
No Picture Ring Set 1 Cylinder - RING SET 1 Cylinder. For tractor models 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 915, all with 414 CID, 6 cylinder turbocharged diesel, standard bore 4.3 inches. Contains 2 x 1/8, 1 x 1/4, per cylinder. Can also be used to replace 687429C91. (Item #: 684256C91) $56.99
Valve, Exhaust - For tractor models 806, 2806. (D361 CID Diesel 6-cylinder engine. Cupped head piston) and models 1206, 21206. (D361 CID Turbo Diesel 6-cylinder engine. Cupped head piston) and models 856, 2856 Tractors and 815 Combines with D407 and 1026, 1256, 21026, 21256 Tractors with DT 407. (D 407 CID and DT407 CID Turbo Diesel 6-cylinder engine. Cupped head piston. Piston pin diameter 1-1/2 inch). (Item #: 169732, Ref: 612313C1) $26.00
Valve, Exhaust - Exhaust Valve. For 966 Tractor and 815 Combines. (DT414 CID Diesel 6-cylinder engine. Cupped head piston) and 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cylinder engine. Cupped Head Piston) and 1466, 1486, 1566, 1586, 3388, 4166, 4186, 5088, 6388 and 1460, 1480 Combines. (DT436 CID DT436B Turbo Diesel 6-cylinder engine. Cupped head piston). (Item #: 156090, Ref: 676865C2) $19.60
Valve Guide - For tractor models 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. Price shown is for each, sold only in multiples of 12 items. (Item #: 172675, Ref: 326505R3) $5.00
Valve, Intake - Intake valve for tractor models 806, 2806. (D361 CID Diesel 6-cylinder engine. Cupped head piston) and models 1206, 21206. (D361 CID Turbo Diesel 6-cylinder engine. Cupped head piston) and models 856, 2856 Tractors and 815 Combines with D407 and 1026, 1256, 21026, 21256 Tractors with DT 407. (D 407 CID and DT407 CID Turbo Diesel 6-cylinder engine. Cupped head piston. Piston pin diameter 1-1/2 inch). (Item #: 169731, Ref: 343433R2) $27.50
Valve, Intake - Intake Valve. For 966 Tractor and 815 Combines. (DT414 CID Diesel 6-cylinder engine. Cupped head piston) and 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cyline engine. Cupped head piston) and 1466, 1486, 1566, 1586, 3388, 4166, 4186, 5088, 6388 and 1460, 1480 Combines. (DT436 CID DT436B Turbo Diesel 6-cylinder engine. Cupped head piston). (Item #: 156088, Ref: 675046C2) $17.80
No Picture Valve Service Kit - Cylinder HEAD Service KIT. For 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. Contains: springs, guides, locks, (no valves). (Item #: VSKH361) $230.89
No Picture Valve Service Kit - Cylinder HEAD Service KIT. For 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. Contains: springs, guides, locks, (no valves). (Item #: VSKH414) $127.04
No Picture Valve Spring - VALVE SPRING. For 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. (Item #: 173502, Ref: 160907R1) $8.00
No Picture Valve Spring - For tractor models 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2806, 2856, 806, 815, 856, 915. (Item #: 172676, Ref: 160908R1) $9.40
No Picture Valve Spring - VALVE SPRING. For 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. (Item #: 156092, Ref: 682064C1) $5.20

Engine Pistons and Sleeves
Piston Pin Bushing - For tractor models 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. Price shown is for each. (Item #: 128614, Ref: 675006C1) $8.50
No Picture Piston Pin Bushing - For tractor models 1456, 21456, 915. (Item #: 157755, Ref: 670681C1) $16.10
No Picture Sleeve - For tractor models 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 3388, 3588, 3788, 4166, 4186, 4366, 4386, 5088, 5288, 5488, 6388, 6588, 6788, 7288, 7488, 815, 915, 966. (Item #: 682720C1) $96.20
No Picture Sleeve and Piston Kit - For 1456, 21456 Tractors and 915 Combines with DT407. (DT407 CID Turbo Diesel 6-cylinder engine. Cupped head piston. Piston pin diameter 1-5/8 inch). Sleeves, pistons and rings, pins and retainers. For 4.321 inch standard bore. (Item #: PK287) $1358.94
No Picture Sleeve and Piston Kit - For 1066, 1086 Tractors and 915 Combines. (DT414 CID DT414B Turbo Diesel 6-cylinder engine. Cupped head piston). Sleeves, pistons and rings, pins and retainers. For 4.3 inch standard bore. (Item #: PK-DT414) $1339.37

Exhaust System
Muffler, Horizontal - Round body 6 inch shell diameter, A= 12 inch inlet length, B= 2-15/16 inch inlet inside diameter, C= 13 inch shell length, D= 20 inch outlet length, E= 3 inch outlet outside diameter, F= 46 inch overall length. For tractor models 815, 915 both with 345 V-8 gas or 6 cylinder diesel engines. (Item #: 120195, Ref: 546129R1) $121.72
Turbocharger with Gaskets - This Turbo Charger comes with gaskets. It is used on tractors using TO4B18 and TO4B25 Air Research style turbos. Fits Engines: 451B, 451BDT DT414, DT429, DT436, DT466, DT466B, DTI466, DTI466B, DTI466C. Replaces OEM numbers A184785, 749267C92, 684240C92, 702300C91, 409570-9016, 409570-5016, TO4B18, TO4B25, A43361, A157335, A43360, A44052, A48190, A66770 (Item #: 101148, Ref: 749267C92) $360.00

Fuel System / Air Intake
Fuel Sediment Bowl Gasket - Gasket, Sediment Bowl. 2 inch outside diameter. This gasket may come with a bonus screen that may not work for your particular tractor. Used on Case Tractors with 2 inch outside diameter sediment bowls. Replaces original part number 13193D. Gasket may be rubber or cork, depending on availability. (Item #: 105383, Ref: 2NAA916061) $2.60
No Picture Injector - Fuel injector assembly, remanufactured. For 1066, 1086, 1440, 1460, 1466, 1480, 1486, 1566, 1586, 3488, 3688, 4166, 4186, 4366, 4386, 453, 666, 686, 766, 815, 886, 915, 966, 986, HYDRO 100, HYDRO 186, HYDRO 70, HYDRO 86 (Item #: 160139, Ref: 631571C91-EX) $62.00

Lights
Sealed Beam Bulb 12V - Sealed beam bulb, 12 volt, 5-3/4 inch diameter, 35 watt, Sealed Beam. Trade number 4419. Replaces: 310062, 230252, 2084379, 70230252, T20958, TO17074, 371443R91, 002803M91, 1038428M91, 1751347M91, 1754916M91, 102213A, 30-2020521 (Item #: 111228, Ref: 70230252) $14.70

Oil System
Oil Filter - Oil filter element, spin on type. Approximate diameter 7.17 inch height, 3.69 inch outside diameter. For diesel engines: D282. D312, D and DT414, D and DT 436, D and DT466. For 1066, 1086, 1460, 1466, 1470, 1480, 1486, 1566, 1586, 2656, 3388, 3488, 3588, 3688, 3788, 4166, 4186, 4366, 4386, 454, 5088, 5288, 5488, 6388, 656, 6588, 666, 6788, 686, 7288, 7488, 815, 85, 915, 966, 986, HYDRO 100, HYDRO 186, HYDRO 70, HYDRO 86. (Item #: 111132, Ref: A184775) $15.30
Oil Filter - Oil filter element, cartridge type with gasket. For gas engines: C221, C263, C291, C301. For diesel engines: D166, D188, D236, D282, D and DT 361, D and DT407. For 1026, 1206, 1256, 1456, 21026, 21206, 21256, 21456, 2504, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 330, 340, 460, 504, 560, 606, 656, 660, 706, 756, 806, 815, 826, 856, 915. Also replaces 279994R91. (Item #: 111127, Ref: 323827R91) $13.40

Seats
Seat Back - Black and white vinyl on steel with original style pleated covering. For 1566, 1568, 2504, 2544, 2656, 2706, 2756, 2806, 2826, 2856, 4156, 4166, Hydro 70, Hydro 86, Hydro 100. (Item #: 127287, Ref: R3662) $212.00
No Picture Seat Brackets, Lower - Steel Brackets (2) to connect lower back to seat. For tractor models 715, 815, 915, 21256, 21456, 2656, 2706 (serial number 3000->), 2756 (standard), 2826, 2856, HYDRO 100, HYDRO 70, HYDRO 86, 1026, 1066 (with vert action), 1256, 1456, 1466 (with vert action), 1468 (with vert action). (Item #: 112241, Ref: 387173R1-SET) $45.10
No Picture Seat Bracket Upper - Steel Bracket to connect upper back to lower back. For tractor models 715, 815, 915, 21256, 21456, 2656, 2706 (serial number 3000->), 2756 (standard), 2826, 2856, HYDRO 100, HYDRO 70, HYDRO 86, 1026, 1066 (with vert action), 1256, 1456, 1466 (with vert action), 1468 (with vert action). (Item #: 109563, Ref: 387178R1) $35.20

Wheels
Front Wheel Bearing - Bearing kit for front wheel, contains inner cone, inner cup, outer cone, outer cup, oil seal. For tractors: 1026, 1066, 1086, 1206, 1246, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, 21026, 2504, 2606 HD Front Axle, 2656, 2706, 2756, 2806, 2826, 2856, 3088, 3288, 3688, 5088, 5288, 5488, 544, 5488, 460 hi clear, 560, 606, 656, 666, 685, 686, 706, 756, 754, 766, 786, 806, 826, 856, 886, 915, 966, 986, Hydro 100, Hydro 186, Hydro 70, Hydro 86 (Item #: 100856, Ref: FW120FS) $34.20
Front Wheel Hub, 8 Bolt - For tractor models 1026, 766, 966, 1066, 1466, 754, 2756, 826, 2826, 856, 2856, 1586, 786, 886, 986, 1086, 1486, 1566, 1568, 3088, 3288, 3688, 5088, 5288, 5488, 666, 815, 1206, 1246, 1468, 706, 2706, 806, 2806, 685, 915. Replaces 1323559C1. Uses FW120FS bearing kit, not included. (Item #: 100878, Ref: 391824R11) $109.00
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $357.14
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.60
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $16.90
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.30
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $4.80
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.80
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.10
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $29.70
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $35.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.50
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.80
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $4.80
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $13.80
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.30
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.10
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.10
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.40
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $13.80
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $24.80
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.20
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.10
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.10
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.40
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $13.60
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.20
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.00

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.80
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.30
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.80
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.30
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.70
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $18.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.70
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $26.50

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $82.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $138.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $102.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $171.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $169.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $110.21
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.70
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $10.30
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.40

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $13.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.50
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $28.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $58.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $37.40
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $45.20
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $373.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $444.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $444.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.50
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $33.30

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.60
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.70
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.00
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.00

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $178.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $123.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.50
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $48.60
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $100.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.20
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $42.20
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $40.80
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.70
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $40.00
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $379.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $119.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.40
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $69.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $54.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.30
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.90
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $57.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $23.30
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $9.40
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $23.30
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.10
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $86.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.00
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $12.40
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $60.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $23.70
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $7.80
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $63.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $13.98
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.80
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $13.98
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $7.80
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $43.90

PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $173.00
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00
NOTE PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.	NOTE
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $280.00