International Harvester / Farmall A Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Band - Lined Brake Band (1). For A, Super A to serial number 339641, B. If a final drive gasket set is needed, order part number 43245D. Replaces: 51582DDX. (Item #: 105417, Ref: 51582DBX) $40.00
Brake Pedal Shaft, LH - Fits A, AV, B, BN, Super A, Super AV, Super AV1, Super A1, 100, 130, 140. (Item #: 153603, Ref: 51425DX) $171.87
Brake Pedal Shaft, RH - This brake pedal shaft is the right hand side. It is for models A, AV, B, BN, Super A, Super AV, Super AV1, Super A1, 100, 130, 140. (Item #: 153602, Ref: 51507D) $168.00
Brake Return Spring - For tractor models 100, A, AV, B, BN, Super A, Super AV, 130, 140. Overall length 7 inch, 2 used for brake pedals, 1 used for clutch pedal. (Item #: 125754, Ref: 47845DA) $15.00
Final Drive Gasket Kit - This 4 piece Final Drive Gasket Kit Includes (1) rear axle housing oil pan gasket, (2) rear axle outer bearing retainer gaskets, (1) rear axle housing inner bearing cap gasket. 2 used per tractor, sold individually. Fits: A, AV, B, BN, Super A, Super A1, Super AV, Super AV1; Replaces: 43245D, 47954D, 48009D, 48009DB (Item #: 182489, Ref: 43245D) $22.90

Clutch
Clutch Assembly - For tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 404, 2404 all with Rockford Style Clutch. New disc and pressure plate assembly (with narrow style fingers). Spring disc, 9 inch disc with 6 splines 1 1/4 inch hub. New release bearing and new pilot bushing and alignment tool (not shown). This kit will replace the early and late style. If you have the graphite bearing, you will also need the new style bearing sleeve and you can order as part number 375493K-Sleeve. Replaces 375493R91, 56631DB, IHS958. (Item #: 118488, Ref: 375493KSP) $214.00
Clutch Assembly - For tractor models A, B, C, Super C, 100, 130, 140, 200, 230, 240, 404, 2404 all with Rockford Style Clutch. New disc and pressure plate assembly (with narrow style fingers). Solid disc, no springs, 9 inch disc with 6 splines 1 1/4 inch hub. New release bearing and new pilot bushing and alignment tool (not shown). This kit will replace the early and late style. If you have the graphite bearing, you will also need the new style bearing sleeve and you can order as part number 375493K-Sleeve. Replaces 375493R91, 56631DB, IHS958. (Item #: 168845, Ref: 375493K) $205.00
Clutch Disc, 9in. Remanufactured - Remanufactured Clutch disc, 9 inch, 4 button spring loaded, 1.250 inch spline diameter, 6 spline. For tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 404, 2404. There is an additional $20.00 for a core charge. (Item #: 205980, Ref: 384384-R4B) $105.72
Clutch Disc, Remanufactured - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 2404, Clutch Size: 9", Clutch Hub: 1-1/4", Clutch Spline: 6, Clutch Center: Solid, Clutch Type: Woven, (Item #: 205978) $93.01
Clutch Disc, Remanufactured, 1944203C1 - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 2404, Replaces International OEM number 1944203C1, 56631DB, 56631DBC, 56631DBR, Clutch Size: 9", Clutch Hub: 1-1/4", Clutch Spline: 6, Clutch Center: Spring, Clutch Type: Woven, (Item #: 203374) $109.50
Clutch Disc, Remanufactured, 384384HD6 - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 2404, Replaces International OEM number 384384HD6, Clutch Size: 9", Clutch Hub: 1-1/4", Clutch Spline: 6, Clutch Center: Solid, Clutch Type: 6 Lg Pads, (Item #: 205979) $139.01
Clutch, Dust Cover - For tractor models A, B, C, Super A, Super C, 100, 130, 200, 230. Cover is 2 inches outside diameter. Check shape and size before ordering. (Item #: 126137, Ref: 57579DX) $14.90
Clutch Fork, Used - For International tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 404, 2404, Replaces International OEM nos 47716D, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 498383) $49.01
Clutch Housing Cover - For A, Super A, AV, B, BN, C, Super C, Cub. Clutch Housing Cover is Oval with Bracket and Screw. Cover is 3 x 4 inches. Check shape and size before ordering. (Item #: 178637, Ref: 57576DX) $22.50
Clutch Kit, Remanufactured - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 404, 2404, Clutch Diameter - 9", Clutch Hub Diameter - 1-1/4", Clutch Splines - 6, Clutch Center - Spring, Clutch Type - Woven, Pressure Plate Size - 9", Pressure Plate Levers - 3, Pressure Plate Springs - 6, Pressure Plate Type - Single Stage, Flywheel Step 1.188", For Pressure Plate use Item #: 122000, (Item #: 202009) $231.80
Clutch Pressure Plate, 9 - Rockford Style with wide fingers. Fits Models: 100, 130, 140, 200, 230, 240, 2404, 404, A, B, C FARMALL, Super A, Super C. (Item #: 189609, Ref: 361581R91) $236.00
Clutch Release Bearing Carrier - This clutch release bearing carrier is the carrier only, does not include bearing. For tractor models A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 404, 2404 (Direct replacement for the following when equipped with replaceable throwout bearing A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C) replaces the graphite style (non-replaceable) throwout bearing and carrier number 350830R31 used on early models. Replaces: 6116D, IHS1155. Uses release bearing part number 361292R91. (Item #: 111782, Ref: 375493K-Sleeve) $86.00
Clutch Release Bearing, Greaseable - For tractor models A, Super A, B, C, Super C, H, Super H, 100, 130, 140, 200, 230, 240, 404, 2404. Bearing is 3.375 inch outside diameter, 2.0625 inch inside diameter. (Item #: 100022, Ref: 361292R91) $25.70
Clutch Release Yoke - This clutch release yoke is 7 5/8 inches overall length. For models A, AI, AV, B, BN, C, Super A, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 404. Industrial A1, 2404. Replaces 47716D (Item #: 178919, Ref: 47716D) $62.80
Pilot Bushing - Inside diameter .883 inch, outside diameter 1.125 inch, thickness .995 inch. For tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 404, 2404. Replaces 364527R1, 364527R2, 364527R91, 43291D, 716678R91. (Item #: 122000, Ref: 364527R91) $9.30
Transmission Disc, 9 inch - Rockford Style, 6 splines 1.25 inch, spring disc (will replace rigid), fits models: 100, 130, 140, 200, 230, 240, 2404, 404, A, B, C FARMALL, Super A, Super C. (Item #: 118489, Ref: 56631DB) $102.00

Cooling System
Fan Assembly - For tractor models A, Super A serial number 250001-317191, Super AV, Super A1, Super AV-1 (ALL A and Super A series between serial number 250001 and 317191), B, C, Super C. Fan measures 15 5/8 inches, pulleys measure 3 3/4 inch and 3 1/4 inch diameter. Replaces OEM number 701360R91, 131489C91, 70136D, 70212D. (Item #: 100772, Ref: 701360R) $85.00
Fan Belt - This Fan Belt measures 35.00 inches length and 0.700 inch width, For, 130 GAS, 200 GAS, 230 GAS, C GAS with WATER PUMP, Super A GAS serial number 48000 to 48499, Super AV GAS serial number 48000 to 48499, Super C GAS serial number 100001 to 114645, Super C GAS serial number 114646 and up. B with water pump. Please verify measurements before ordering (Item #: 111155, Ref: 60712D) $15.30
Fan Belt - For tractor models A, B, C (with C-113 engine; without water pump), Super A. 3/4 inch x 34 inch. (Item #: 153766, Ref: 46869D) $12.80
Generator Belt - For tractor models 130, 200, 230, (A, AV serial number 317191 and up), B, BN, Super A, Super AV, (Super C serial number 114646 and up). All with gas engines. 1/2 X 28.125 (Item #: 172686, Ref: 52318DA) $5.90
Radiator - For Farmall A (SN# 41330 and UP) and B (SN# 40193 and UP) also Super A, Super AV, Super AV-I To SN# 3555669 without Water Pump. Replaces OEM 58124DBX. (Item #: 125004, Ref: R2771) $462.00
Radiator - This Radiator fits all A, B and BN models as well as Super AV and Super AV-1. It will fit older non-pressurized systems and is close to, but not exactly like original. For original non-pressurized, see part number 58124DBX. If using this radiator to replaces an older non-pressurized radiator, you will also need to replace the cap with part number RW0021-9 (4 lb cap). If replacing the cap for a pressurized system use cap part number 825702M2 (7 lb cap). Core Height 15 7/8 inches, Core Width 16 inches, Depth 2 inches. Replaces original part numbers 358105R91, 58124DBX (Will need new cap). (Item #: 101706, Ref: 358105R91) $400.00
Radiator - This radiator is for the early models without water pump. Has 2 Inch Inlet and Outlet Tubes. Fits A and AV after serial number 41330, B and BN after serial number 40193, (Super A, Super AV, Super AV-I, all to serial number 355669) all without water pump. Has 2 inch inlet and outlet tubes. Core size is 17 3/8 inches wide X 16 1/2 inches high. Does not come with a cap. Uses Radiator Cap part number 43983D. (Item #: 125004, Ref: 58124DBX) $462.00
Radiator and Air Hose Set - For tractor models A, Super A WITHOUT water pump, B. Radiator and Air Cleaner Hose Kits include Original Whittek Tower Style Hose Clamps. Radiator hoses are 2.25 inches long and 2 inch inside diameter. (Item #: 182510, Ref: R2700) $48.60
Radiator Cap - This is a 4lb Radiator Cap used with 358105R91 when replacing a non-pressurized radiator. (Item #: 178173, Ref: RW0021-9) $8.00
Radiator Cap - This is a 7 pound Radiator Cap used with 358105R91 for a pressurized system. Replaces: 361705R91, 362323R91. (Item #: 169633, Ref: 825702M2) $12.80
Radiator Cap - For tractor models A, Super A, B, C with Non pressurized system. This cap is original style with water imprint. Does not fit our part #358105R91. This cap is used on an original non-pressurized system radiator and the new 58124DBX. (Item #: 112117, Ref: 43983D) $9.50
Radiator Hose - Lower - For International / Farmall tractor models A (s/n 355669-earlier), B, Super A, 140, 240, 404, 424 (gas), 444 (gas), Replaces International OEM number 20075DB, 2" ID, For Hose Clamp use Item #: 130455, (Item #: 112337) $4.30
Tower Hose Clamp 2.685" to 2.995" - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, H, Super A, Super C, Super H, 100, 130, 140, 200, 230, 240, 300, 330, 350, 400, 450, 656, 706, 756, 806, 826, 856, 2706, 2756, 2806, 2826, 2856, Compatible with International Harvester (s) 55, 350, 550, 650, Replaces International OEM number 39205H, 706081R91, (Item #: 130443) $7.50
Water Block Drain Plug, Winged - Plug 3/8 inch pipe thread, has "IH" and part number stamped in it, cast iron with zinc plating. For tractor models A, AV, Super A, Super AV, Super A1, Super AV1, B, BN, C, H, HV, Super H, Super HV, I4, I6, ID6, I9, ID9, M, MD, MV, MDV, Super M, Super MD, Super MV, Super MDV, MTA, 04, 0S4, 06, 0S6, ODS6, T6, T340, TD6, T9, TD9, W400, W450, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650 (Gas/Diesel), serviceable for Cub, Cub Lo-Boy. (Item #: 178066, Ref: 45314DC) $12.70
Water Pump Gasket Set - This set is included with 355760R93 water pump. Set includes 68104C1 and 355769R1. (Item #: 183008, Ref: 68104C1) $10.90
Water Pump - New - With pulley, fits A, B, C and models with C123 Gas Engine: 100, 130, 200 serial number <501-65000, 230 serial number <501-65000, Farmall 240 serial number <501-65000, Super A, Super C. Casting number 367683, 367684 or 372241. (Item #: 107899, Ref: 355760R93) $67.00
Water Pump, Remanufactured, 123868 - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 200, 230, 240, Replaces Casting number 123868, Includes Mounting Gasket, With Pulley, (Item #: 206125) $112.01
No Picture Water Temperature Gauge - For A, B to 1946. Water Temperature Gauge with 14" Lead and "IHC" Logo. (R4180) (Item #: 184789, Ref: 53619DC) $78.51

Decals and Emblems
Decal Set - For Farmall A Culti-vision. Set of 14 self adhesive decals. Printed on Mylar, not die cut. (Item #: 100901, Ref: IHCACV) $93.00
Decal Set - For model A, McCormick Deering (1939-1944). This is a set of 11 self adhesive decals. These are printed on Mylar, not die cut. (Item #: 182632, Ref: IHCMDA) $36.40
Decal Set - For model A McCormick (1945-1952). This is a set of 9 self adhesive decals. These are printed on Mylar, not die cut. (Item #: 101034, Ref: IHCA) $51.00
Front Emblem - At 10 inches long, this front emblem has raised "International, " rather than the more common Farmall. Used on the industrial versions of the A and B tractors. Bright Aluminum finish. Replaces 8000031, 54208D (Item #: 110932) $24.70
Front Emblem - For tractor models A, AV, B, BN. Bright Metal With Farmall Spelling. (Item #: 103896, Ref: 43658D) $18.80
IH Decal, 1-5/8", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1 5/8", no background, (Item #: 101024) $2.80
IH Decal, 1", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1", no background, (Item #: 101023) $1.90
IH Decal, 3" x 3-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 3" x 3-1/2", No background, (Item #: 101025) $11.20
IH Decal, 4-1/2" x 5" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 4-1/2" x 5", Mylar decal, (Item #: 101095) $5.60
International A Culti-vision Decal Set, Farmall, McCormick, Mylar - For International / Farmall tractor model A (Culti-vision), Vinyl decal set use Item #: 100914, (Item #: 101043) $51.00
International A Decal Set, Vinyl - For International / Farmall tractor model A, (Item #: 100962) $82.00
International AV Culti-vision Decal Set, Farmall, McCormick, Mylar - For International / Farmall tractor model A (V, Culti-vision), Vinyl decal set use Item #: 100916, (Item #: 101045) $56.00
International Decal, 17", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 17" long, Black, Mylar decal, (Item #: 101105) $5.60
International Decal, 8-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 8 1/2" long, Black, Mylar decal, (Item #: 101104) $3.80
International Decal Set,10" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 10", (Item #: 101022) $29.70
International Decal Set, 1 1/4" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-1/4", (Item #: 101018) $2.80
International Decal Set, 1 3/4"x 1 5/8" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-3/4", (Item #: 101019) $3.80
No Picture International Decal Set, 6 1/2"x 7" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo 7", Vinyl Cut, Shaded Outline, (Item #: 101020) $16.80
No Picture International Decal Set, 7 1/4"x 8" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 8", (Item #: 101021) $22.30
International Harvester Decal, 2-3/4" x 3" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, (Item #: 101093) $3.80
International Harvester Decal, 2" x 2-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/2", No background, Mylar decal, (Item #: 101097) $3.80
International Harvester Decal, 2" x 2-1/4", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/4", Mylar decal, (Item #: 101092) $3.80
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", Mylar decal, (Item #: 101096) $5.60
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", No background, Mylar decal, (Item #: 101098) $5.60
International Harvester Decal, 5" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 5" diameter, Shaded outline, Mylar decal, (Item #: 101099) $5.60
International Harvester Decal, 6" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 6" diameter, Shaded outline, Mylar decal, (Item #: 101100) $7.50
International Harvester Decal, 7-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 7 1/2" diameter, Shaded outline, Mylar decal, (Item #: 101101) $9.30
International Harvester Decal, 9", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 9" diameter, Shaded outline, Mylar decal, (Item #: 101102) $11.20
International Hood Decal, 23-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, Size: 23-1/2", Black lettering, (Item #: 101031) $14.90
International McCormick-Deering Farmall Decal Set, A, Vinyl - For International / Farmall tractor model A, (Item #: 100894) $93.00
International McCormick Farmall Decal Set, A 1945-52, Vinyl - For International / Farmall tractor model A, Mylar decal set use Item #: 101034, (Item #: 100905) $93.00
International McCormick Farmall Decal Set, A Culti-Vision, Vinyl - For International / Farmall tractor model A, Mylar decal set use Item #: 101043, (Item #: 100914) $93.00
International McCormick Farmall Decal Set, AV Culti-Vision, Vinyl - For International / Farmall tractor model A, Mylar decal set use Item #: 101045, (Item #: 100916) $93.00
McCormick International Decal, 10" Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 10" long, Black and white, Vinyl decal, (Item #: 101103) $9.30
McCormick International Decal, Hood, White/Black, 7-1/4", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 7-1/4" black and white, Vinyl decal, (Item #: 101026) $7.50

Drive Train
Axle Oil Seal - This axle oil seal fits the following tractor models: A, Super A, 100, 130, 140, and Cub. It has an inside diameter of 1.750 inches, an outside diameter of 2.632 inches, and a width of 0.500 inches. It replaces part numbers: 264698R91, 273563R91, 275596R91, 357768R91, 382220R91, 383387R91, and 53599D. (Item #: 182568, Ref: 264698R91) $20.00
Final Drive Gasket Kit - This 4 piece Final Drive Gasket Kit Includes (1) rear axle housing oil pan gasket, (2) rear axle outer bearing retainer gaskets, (1) rear axle housing inner bearing cap gasket. 2 used per tractor, sold individually. Fits: A, AV, B, BN, Super A, Super A1, Super AV, Super AV1; Replaces: 43245D, 47954D, 48009D, 48009DB (Item #: 182489, Ref: 43245D) $22.90
Gear Shift Knob - For Cub, Cub Lo-Boy, A, Super A, Super AV, B, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, W4, W6, WD6, Super W6, W9, WD9, Super WD9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 354, 400, 404, 450, 424, 460, 504, 560, 600, 606, 660, and on the hydraulic lever control on the 454 and 574. Gear shift lever knob. Replaces 3121549R1, IHS266. (Item #: 109514, Ref: 53717DA) $5.90
Gear, Transmission Oiler Slinger - Also replaces 58340D. For tractor models 100, 130, 200, 230, 240 with High Speed and Low Reverse Attachment, A serial number 39022>, B serial number 39022>, A, C, Super A, Super C. (Item #: 172572, Ref: 354643R11) $199.00
Oil Seal - Fits: [A, A-I, A1, AV, AV-1, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 2404, 404 (Top Transmission Shaft Front Seal)], [B-250, B-275, B-276, B-414, 2300, 2300A, 2424, 2444, 3414, 3444, 354, 364, 384, 424, 434, 444 (Bull Pinion Shaft Bearing Retainer Seal)], [Cub, Cub Lo-Boy, 154, 184, 185 (Final Drive Upper Pinion Shaft Seal)], [M, MD, MDV, MV (Transmission Counter Shaft Front Seal)], MTA (Front Wheel Seal; with single front 900 x 10 wheel), [O4, OS4 (PTO Output Shaft Seal; serial number 2159 to 9300)], [Super M, Super MD, Super MDV, Super MV (Transmission Counter Shaft Front Seal; up to serial number F52627 and up to seril number L51241)], W4 (PTO Output Shaft Seal; serial number 786 to 9300). Replaces: 21969D, 264694R91, 287440R91, 3043788R91, 3043788R92, 358765R91, 358784R91, 358808R91, 358823R91, 381907R91, 42177D, 43278D, 50839D, 530969R91, 703907R91, 703908R92, A29424. (Item #: 178204, Ref: 381907R91) $6.00
Rear Outer Flanged Axle Seal - This Rear Outer Flanged Axle Seal measures 2.125 inches inside diameter, 3.001 inches outside diameter and 0.434 inches wide. Fits A, AV, B, BN, Super A, Super A1, Super AV, Super AV1. Replaces original part numbers 358767R91, 358810R91, 43283D, 71697C1 (Item #: 167998, Ref: 15287A) $9.60
Rear Stub Axle Felt Washer - This Rear Stub Axle Felt Washer measures 2.920 inches outside diameter, 2.000 inch inside diameter and is 0.375 inches thick. A, AV, B, BN, Super A, Super A1, Super AV, Super AV1. Two used per tractor. Sold individually. Replaces: 15017D, 43242D. (Item #: 178083, Ref: 43242D) $14.20
Seal, Differential Ball Bearing - For tractor models A, A1, AI, AV, B, BN, Super A, Super A1, Super AV, Super AV1, 100, 130, 140. This seal measures 2.378 inches outside diameter, 1.531 inches inside diameter and 0.500 inches wide. wide. 2 used per tractor, sold individually. Replaces: 358773R91, 358813R91, 381742R91, 383340R91, 385865R91, 45175D, 46282D, 71597C1, 71597C91 (Item #: 172757, Ref: 71597C1) $26.30
Transmission Gasket Kit - This three piece Transmission Gasket Kit includes transmission shift cover gasket, transmission spline shaft bearing retainer gasket and counter shaft bearing cage gasket. It fits: A, AV, B, BN, Super A, Super A-1, Super AV, Super AV-1, 100, 130, 140. Replaces original part numbers 1342393C1, 46503D, 47279DA, 47283D, 47283DB (Item #: 178158, Ref: 1342393C1) $26.60

Electrical System
Alternator Bracket Kit - This alternator bracket has a 2 inch gap for the alternator part number 8NE10305SE and will fit the following tractor models A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 200, 230, will also work for Power units U2, U2A. (Item #: 127584, Ref: IHALTBKIT) $62.00
Battery Box Grommet - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, H, I4, I6, I9, M, MD, O4, O6, Super H, Super M, Super MTA, Super W4, W4, W6, W9, 300, 350, 400, 450, Replaces International OEM number 248-1146, 24179D, 52118D, (Item #: 126446) $2.50
Coil, Original, 12 Volt - OEM style coil. For tractor models 100, A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, MD, W4, W6, Super W4, Super W6, Super W6TA, W9, Super W9, Cub, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450. This is an International Harvester OEM style 12 volt distributor coil. This distributor coil has a 2.8 ohm rating between the two primary winding terminals. Requires an external resistor. (Item #: 154651, Ref: 353875R91) $65.00
Coil, Original, 6 Volt - OEM style coil. Measures overall length of 5 3/8 inches, Diameter at widest point of center ridge is 2 1/4 inches. This distributor coil has a 1.4 ohm rating between the two primary winding terminals. For tractor models 100, A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, MD, W4, W6, Super W4, Super W6, Super W6TA, W9, Super W9, Cub, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450. (Item #: 154650, Ref: 353874R91) $66.00
Distributor - Original IHC design comes with a 32 tooth drive gear. For tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, Cub 154 Lo-Boy, Cub 184 Lo-Boy, Cub 185 Lo-Boy, H, HV, I4, I6, I9, ID9, ID6, M, MD, MDV, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD-TA, Super MDV, Super MTA, Super MV, Super W4, Super W6. R6332 (Item #: 124839, Ref: 107304C91) $120.00
Distributor - New and complete distributor comes with a 32 tooth gear, and is for tractor models: A, AV, B, BN, C, H, HV, M, MV, Super A, Super AV, Super C, Super H, Super M, Super MTA and other IH equipment with International Distributors. Replaces: 107296C91, 107299C91, 107302C91, 107304C91, 353890R91, Distributor Housing Casting Number: 353898R11, 354900R91, 357935R91, 362473R91, 362722R91, 364653R91, 364696R92, 366928R91, 372712R91, 380622R91. Uses IH points (included). (Item #: 124839, Ref: 107304C91) $120.00
Distributor Breaker Plate - Used on International Distributors, this plate is where points are secured. Points not included. Four Cylinder Models: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 450, 504, A, AV, B, BN, C, Cub, 154 Lo-Boy, Cub 185 Lo-Boy, H, M, MD, Super A, Super M, Super C, Super H, Super HV, M, MV, MD, Super M. (All with IH Distributor, not for Delco Distributor). Replaces 352277R11 (Item #: 190142, Ref: 352277R11) $24.90
Distributor Cap - Distributor cap for 4 cylinder models using a Delco distributor with a clip held cap. Replaces 811735 Delco and 1750411M1. For tractor models A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDV, 4, Super 4, 6, Super 6, 9, Super 9, 354, B414. (Item #: 104554, Ref: 1750411M91) $8.50
Distributor Cap - 2-3/16 inches high, fits 4 cylinder. Models: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 450, 504, A, AV, B, BN, C, Cub, 154 Lo-Boy, Cub 185 Lo-Boy, H, M, MD, Super A, Super M, Super C, Super H, Super HV, M, MV, MD, Super M. (All with IH Distributor, not for Delco Distributor). Will also fit J4 magneto. (Item #: 105571, Ref: 351693R92) $9.20
Distributor Cap Spring Clip - Fits listed IH models when equipped with IH brand distributor 353898R11. Replaces: 107384C1, 353894R1 (Item #: 178117, Ref: 353894R1) $16.80
Distributor Condenser - Services IH distributors 1951 to 1962 also services J4 magnetos. For tractor models 200, 230, 240, 2404, 2504, 2606, 2706, 2806, 300, 330, 340, 350, 400, 404, 450, 460, 504, 560, 606, 660, 706, 806, A, B, C, Cub, Cub 154, Cub 185 Lo-Boy, Cub Lo-Boy, H, HV, M, MD, Super A, Super C, Super H, Super M, Super MTA. (Item #: 111108, Ref: 353903R1) $7.70
Distributor Drive Housing - This is a new distributor drive housing with an opening for tachometer drive. It is used to change from a magneto to a distributor or to add a tachometer drive to your tractor. The tachometer drive parts (tachometer drive assembly part number 369695R1, tachometer cable connector housing, part number 369692R1 and 363817R1, connection housing plate) or tach. Drive blockoff plate are sold separately. NOTE: Will also work on tractors without tach drive by ordering number 363764R1 block off plate. Use with 107304C91 distributor when replacing a magneto. fits tractor models A, A1, AV, AV-1, B, BN, C, Cub, Cub Lo-Boy, H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W9, W4, W6, W6TA, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 2504, 300, 330, 340, 3444, 350, 3514, 404, 424, 444, 504, 400, 600, 650 450. Replaces: 363749R91, 363763R11. (Item #: 178938, Ref: 363749R91) $108.00
Distributor Drive Shaft - Shaft for the Distributor Drive. For Cub, Cub Lo-Boy, A, Super A, Super AV, B, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MD, 06, OS6, W6, WD6, W9, WD9, WR9, WDR9, WR9S, 200, 330, 340, 350, 400, W400, 404, 450, W450, 504. Distributor Shaft, for battery ignition with original IH distributor. (Item #: 110682, Ref: 353934R11) $17.80
Distributor Dust Cover - Fits early Delco Distributor with Clip Held Cap. For tractor models (A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super HV, M, MV, Super MV, MTA. All with Delco Vertical Conversion Distributor 1111411). (Item #: 103153, Ref: 1900119) $9.00
Distributor Dust Cover - Used with horizontal IHC distributor 353898R11 or J4 magneto on Models: A, AV, Super A, Super AV1, B, BN, C, Super C, Cub, Cub Lo-Boy, H, HV, Super H, Super HV, M, MV, MD, MDV, Super M, Super MD, Super MTA, W4, W6, W9, WR9, WR9S, WDR9, O4, O6, OS6, ODS6, I4, I6, ID6, I9, ID9, T6, TD6, TD9, 100, 130, 140, 154, 184, 185, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404. Replaces 384831R91. (Item #: 107074, Ref: 353900R11) $16.10
Distributor Gear - This Distributor Gear has 32 teeth. It is used on IH Distributor 353898R11. Replaces original part numbers 353902R1, 531461R91 (Item #: 111179, Ref: 353902R1) $29.00
Distributor Hold Down Clamp - For 5/16 inch hold down bolt and IH built distributor. 2 used per engine, sold individually. Fits fits tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, H, HV, Hydro 70, Hydro 86, I4, I6, I9, ID6, ID9, M, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, W4, W6, W9, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 2505B, 2510B, 2514B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 574, 600, 606, 650, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856. All with IH distributors. Replaces 341139R1, 353937R1. (Item #: 182464, Ref: 341139R1) $9.20
Distributor Point Set - For J-4 Magneto and IH 353898R1 Distributor. Point Gap = 0.013 inches. Replaces 21A161, 407018R91, 353172R1, 353172R91. (Item #: 111109, Ref: 353172R1) $7.00
Distributor, Rebuilt - Complete remanufactured distributor for Farmall Cub, A, B, C, Super A, H, M, Super H, Super M, W6, W9, Super W6, 100, 130, 200, 240, 300, 400, 404, 450, 504 tractors with IH distributor with 353898R1 housing casting number. IH original part numbers 353890R91, 107304C91. A refundable $50.00 core charge will be added to your order. (Item #: 203587, Ref: 353898R1) $235.01
Distributor Rotor - For IH Distributors on models: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 4, 400, 404, 424, 444, 450, 6, A, AV, B, BN, C, H, HV, M, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super A, Cub, Cub Lo-boy, Cub 154-Lo-boy, Cub 185-Lo-boy. NOT FOR USE ON EARLY MODELS WITH A MAGNETO. (Item #: 110266, Ref: 353896R1) $4.40
Distributor Shaft Bushing and Shim Kit - Delco Distributor Shaft Bushing and Shim Kit. Fits A, A-I, A1, AV, AV-1, B, BN, C, H, HV, I4, I6, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, T6, U2, U2A, U4, U6, W4, W6 all with Delco vertical conversion distributor 1111411. Replaces: washer: 811913, shim washer: 810074, 810078, bushing: 1909003, 1952334 (Item #: 178103, Ref: ABC3007) $29.50
Distributor Shaft Bushing and Shim Kit - International Distributor Shaft Bushing and Shim Kit. Fits tractor models A, A1, AV, AV1, B, BN, C, Cub, Cub Lo-Boy, H, HV, M, MTA, MTAV, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 300, 330, 340, 3444, 350, 3514, 400, 404, 424, 444, 450, 504, 600, 650. Replaces: 252739R1, 352298R1, 353899R1, 353921R1, 373577R91, 86637641. This is a 5-piece kit. The length is 2.006 inches. (Item #: 178766, Ref: IHS3166) $44.80
Distributor Terminal Insulator Assembly, Delco - This Delco Distributor Terminal Insulator Assembly is for Round Shoulder (outside terminal). Note: As distributors can be changed over time, it is best to double check which style you require. This is only a guide of what was original. Fits distributor housings with 0.345 inch diameter round hole. If not sure, measure before ordering. Used on Some of the following, using Delco 1111411 vertical distributor with round insulating terminal: I4, I6, T6, A, AV, B, BN, C, H, HV, M, MV, O4, O6, Super C, Super H, Super M, Super MV, W4, W6 (Item #: 111459, Ref: 1878405ASSY) $15.00
Distributor Terminal Insulator Assembly, Delco - This Delco Distributor Terminal Insulator Assembly is for Square Shoulder (outside terminal). Note: As distributors can be changed over time, it is best to double check which style you require. This is only a guide of what was original. Fits distributor housings with 0.300 Inch diameter round hole with a keyway. If not sure, measure before ordering. Fits Farmall / IH with Delco 1112461, 1112601, 1112655, 1111411, 1112607, 1112609. This if for vertical Delco Distributors. Not for IH Distributors or Magnetos. Replaces: 120622, 817363, 1914142, 1914144, 1916805, 1916806 (Item #: 111468, Ref: 1904376) $14.40
Distributor Terminal Screw - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a zinc plated Terminal Screw. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. Replaces International part number 353907R1 (Item #: 118472, Ref: 353907R1) $7.70
Distributor Terminal Screw Insulator - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a spring anchor terminal insulator. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. (Item #: 118473, Ref: 353906R1) $7.20
Distributor with base and tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, M, Super A, Super C, Super H, Super M, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2424, 2504, With tachometer drive and with base, Includes new distributor cap, points, condenser, 6V coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203589) $350.01
Distributor with base and tach drive, Used - For International tractor models A, B, C, Cub, H, M, Super A, Super C, Super H, Super M, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2424, 2504, With tachometer drive and with base, Includes new distributor cap, points, condenser., Does Not Include Coil, For a Remanufactured version of this part use Item #: 203589, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 403589) $291.01
Distributor with base less tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2404, 2424, 2444, 2504, 3444, 3514, Compatible with International Combine (s) 105, 203, Compatible with International Construction and industrial models T6, T340, 500, Without tachometer drive and with base, Includes new distributor cap, points, condenser, 6V Coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203588) $235.01
Distributor with Electronic Ignition - New and complete distributor comes with a 32 tooth gear, and is FOR USE WITH 6 VOLT POSITIVE GROUND SYSTEMS ONLY. Replaces 354900R91, 107296C91, 366928R91, 357935R91, 353890R91. For: A, AV, B, BN, C, H, HV, M, MV, Super A, Super AV, Super C, Super H, Super M, Super MTA. (Item #: 113311, Ref: 107304C91-6V) $655.78
Distributor with Electronic Ignition - 12V - New and complete distributor comes with a 32 tooth gear, and is FOR USE WITH 12 VOLT NEGATIVE GROUND SYSTEMS ONLY. Replaces 354900R91, 107296C91, 366928R91, 357935R91, 353890R91. For: A, AV, B, BN, C, H, HV, M, MV, Super A, Super AV, Super C, Super H, Super M, Super MTA. Note: This distributor has a maximum advance of 21 degrees. Some applications require an advance up to 40 degrees. Verify with your service manual this distributor will work for your application. (Item #: 113361, Ref: 107304C91-12V) $674.02
Electronic Ignition Conversion Kit - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 6 volt POSITIVE ground system only. Use with distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650 (Item #: 105084, Ref: 1442P6) $195.00
Electronic Ignition Conversion Kit - Electronic Module Replaces Points and Condenser. Use on tractors with 12 volt Positve Ground System only. (FOR NEGATIVE GROUND order part number 1442). Use with distributor number 357935R91 or 353898R1 on models: B, Cub, cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650. (Item #: 105085, Ref: 1442P12) $174.00
Electronic Ignition Conversion Kit - 12v Negative Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt NEGATIVE ground system only. Distributors with clip type cap. (Item #: 105071, Ref: 1142) $155.00
Electronic Ignition Conversion Kit - 12V Negative Ground - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 12 volt NEGATIVE ground system only. Use with IH distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650. Verify distributor number before ordering. (Item #: 105083, Ref: 1442) $164.00
Electronic Ignition Conversion Kit - 12v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. 1885368 or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt POSITIVE ground system only. (Item #: 108148, Ref: 1142P12) $177.00
Electronic Ignition Conversion Kit, 6v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with Delco distributor part no. 1885368 with clip type cap. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 6 volt positive ground system only. (Item #: 105072, Ref: 1142P6) $160.00
Fuse Housing - Reproduction of original Fuse Housing. Comes as pictured. For tractor models (Super A, Super AV, A1 all with magneto), C, Super C, 200, (H late with regulator under tank), Super H, HV, (M with regulator on post), (Super M 1953-1954), (Super M diesel), Super MTA, W4, OS4, O4, 100, 130, 400, 450. Replaces: 365515R91, 376852R91, 354232R91 (Item #: 112273, Ref: 376852R91) $10.90
Generator Belt - For tractor models (A, AV serial number 250001 to 317191), B, BN, C, Super A, Super AV, (Super C serial number 100001 to 114645) all with gas engines. 1/2 X 26.125. (Item #: 161749, Ref: 49291D) $10.40
No Picture Generator - Delco Style (9718), Remanufactured, Delco Remy, 1100501 - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, I9, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, Compatible with International Combine (s) 101, 140, 151, Compatible with International Construction and industrial models T6, Compatible with International Baler (s) 37, 47, 57, Replaces Delco Remy manufacturer number 1100501, Replaces manufacturer number 9718, 340-21, 92-01-3050, Delco Style, Voltage: 6, Rotation: Clockwise, Amperage: 25, Regulator: External, (Item #: 203178) $408.38
H4 Magneto Pinion Driven Gear - This gear has 24 teeth and measures: 0.380 inch inside diameter, 0.759 inch outside diameter, 1.075 inch gear outside diameter, 0.952 inch overall height. It is used on H4 Magnetos. (Item #: 183878, Ref: 49420DX) $26.20
Hand Crank Mounting Bracket - For International / Farmall tractor models A, B, Super A, 100, 130, 140, Replaces International OEM number 350639R91, (Item #: 122097) $28.40
Ignition Switch - For the following Models using a magneto: Cub, Cub Lo-Boy, A, B, C, H, M, 100, 130, 140, 200, 230, 300, 350, 400. NOT like original. (Item #: 111178, Ref: 54207DB) $13.40
Ignition Switch - 2 terminal. For the following Models using a distributor: Cub, Cub Lo-Boy, A, Super A, B, C, Super C, H, Super H, M, Super M, (140 6 volt), 200, 230. NOT like original. (Item #: 111177, Ref: 62801DC) $10.30
Ignition Switch - This Ignition Switch is for Distributor Ignition Systems. This is a 2 terminal switch. For A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, Cub, 100, 130, 140, 200, 230 (Item #: 117579, Ref: R2720) $39.00
Ignition Switch - This Ignition Switch is for Magneto Ignition systems. This switch has only 1 terminal. For A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, Cub. Replaces 54207DB (Item #: 117580, Ref: R2721) $49.00
Ignition Tune-up Kit, Basic, Delco Clip Held Cap - Ignition kit For Delco ONLY distributor with CLIP held cap. VERIFY DISTRIBUTOR NUMBER TO ENSURE FIT. Contains points, condenser, and rotor. For tractor models A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDV, 4, Super 4, 6, Super 6, 9, Super 9, 354, B414, I4, I6, MTA, MV, O4, O6, T6, U2, W4, W6. For Delco distributor numbers 1111716, 1112583, 1112589, 1112557, 1112570, 1112585, 1111722, 1111737, 1112583. Not for IH Distributors. (Item #: 103151, Ref: ATK1DCR) $9.50
Lighting Switch Dimmer Resistor - For International / Farmall tractor models A, B, Cub, H, HV, M, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super W4, Super W6, TD6, TD9, W4, W6, W9, 100, 130, 200, 230, 300, 350, 400, 450, Replaces International OEM number 47889D, Will Not Fit 154, 184, 185, (Item #: 126566) $16.40
Magneto - This is a New Wico Magneto used on Farmall / IH Models: A, AV, B, BN, C, H, HV, I9, M, MTA, MTAV, MV, O4, O6, OS6, Super A, Super C, Super H, Super M, W4, W6, W6TA, 100, 130, 200, 230, 300, 350, 400, 450, 600, 650. It is also used on some industrials and power units. (Item #: 180178, Ref: XH1344) $567.00
Magneto Coil Cover - For tractor models 100, 130, 200, 230, 240, 300, 330, 340, 350, 400, 450, W4, W6, A, B, BN, C, H, HV, M, MD, Super A, Super A1, Super C, Super H, Super HV, Super M, Super MTA. (Item #: 105661, Ref: 47449DAY) $29.50
Magneto Condenser - Condenser for IH Models using H4 F4, J4 Magneto (replaces 373892R91). For tractor models 100, 130, 200, 300, 350, W4, W6, A, B, BN, C, H, M. Note, this condenser will ship as one of two functionally identical versions shown, a long piece OR a short with an extension, depending on stock available. Replaces 21409DA, 21409DB, 354136R92, 373892R91, 47546D, 71455C91 (Item #: 111418, Ref: 71455C1) $10.90
Magneto Distributor Cap, H4 Magneto - For H-4 MAGNETO ignition on Models: 100, 200, 230, 240, 300, 330, 340, 350, 400, 450, A, B, C, H, HV, M, MD, Super A, Super A1, Super C, Super H, Super HV, Super M, Super MTA. (Item #: 105662, Ref: 47413DYC) $17.00
Magneto Gasket Set - This magneto gasket set is for H4 Magnetos. It contains; Coil cover gasket 47453D, Distributor body gasket 47408D, Distributor gear cover gasket 49419D, Condenser hole cover gasket 359966R1 (48472DA), Magneto mounting gasket 55780DE (55780DD). Replaces: 359966R1, 47408D, 47453D, 48472DA, 49419D, 55780DD, 55780DE, E4226. For tractor models A, AV, B, BN, C, H, HV, I4, I6, I9, M, MTA, MV, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, T4, T5, T6, T9, U2, U2A, U4, U6, U9, W4, W6, W6TA, W9, WR9, WR9S, 100, 130, 200, 230, 300, 350, 400, 450, 600, 650, 400, 450 (Item #: 111272, Ref: MGK103) $10.00
Magneto Points - Point Set Fits J4 and H4 Magneto (can work with F4 magneto with modify) (Item #: 111110, Ref: 353171R91) $9.00
Magneto, Remanufactured, 374867R91 - For International / Farmall tractor models A, B, C, H, M, W4, W6, 100, 130, 200, 300, 350, Replaces International OEM number 374867R91, Right-hand flange mount, International H4 magneto, For Tune-Up Kit use Item #: 105661, (Item #: 203606) $1025.01
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.90
Magneto Tune-up Kit For H4 - Magneto Tune-up Kit For H4 Magneto used on: 100, 130, 200, 230, 240, 300, 330, 340, 350, 400, 450, W4, W6, A, B, BN, C, H, HV, M, MD, Super A, Super A1, Super C, Super H, Super HV, Super M, Super MTA, W4, W6. Includes condenser, points, rotor. (Item #: 105297, Ref: 21A10R) $22.90
Point Set - For International / Farmall tractor models A, B, C, H, M, W4, W6, 100, 130, 200, 300, 350, Replaces International OEM number A2437A, Fits Fairbanks Morse FM-XV magneto, (Item #: 111707) $17.10
Push/Pull Switch Knob - For International / Farmall tractor models A, B, C, Cub, H, HV, M, MD, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, W4, W6, W9, Replaces International OEM number 8732D, Knob only replacement for push/pull switches, (Item #: 126614) $7.00
Rotor - Used with Delco distributors 1111411 with a clip held cap. For tractor models: A, I4, AV, Super A, Super AV, Super AV1, B, BN, C, Super C, H, HV, Super H, Super HV, M, Super M, MTA, Super MTA, MV, Super MV, O4, O6, OS4, OS6, T6, W4, W6, 354 (distributors with a tach drive). Replaces 3069778R1. (Item #: 110177, Ref: 1750498M1) $3.60
Spark Plug - Spark Plug 18MM Thread Diameter for: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 460, A, AV, B, BN, C, H, HV, M, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super A, Cub, Cub Lo-boy, Cub 154-Lo-boy, Cub 185-Lo-boy. Replaces OEM number 360942R1. Also replaces Autolite AL386, AL388, AL3116 and Champion D16, 516, D10, D14, D16J, D21, D89D, K13, K15J, M14, RD14, RD16, UD16 plugs (Item #: 111742, Ref: AL386) $3.20
Spark Plug Wire Set, Custom - IH or Delco Distributors and Magnetos. For the following models with 90 degree angle boots: A, I4, AV, Super A, Super A1, Super AV, SuperAV1, B, BN, C, Super C, Cub, Cub Lo-Boy, 154, 184, 185, H, HV, Super H, Super HV, M, MD, Super M, Super MD, Super MDV, MDV, Super MDVTA, MTA, Super MTA, MV, Super MV, Super MVTA, O4, O6, ODS6, OS4, OS6, T340, T5, T6, TD6, SuperW4, W4, Super W6, Super W6TA, W6, W6TA, Super WD6, WD6, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404, 424, 444, 450, W450, 504. Replaces the following OEMS: 352947R91, 352951R91, 352954R91, 352956R91, 356687R92, 356689R92, 356691R91, 356694R92, 356695R92, 356697R93, 362439R91, 362789R91, 407487R1, 45327DA, 46277DA, 50075D, 52794D, 65352D, 65357D, 65358D, and 65359D. (Item #: 120100, Ref: S.67475) $15.20
Starter - This is a new 6 volt starter with Solenoid. It is original equipment on Farmall 140HC and 240. It has a 10 tooth drive with counter clockwise rotation. It replaces; International part number 360606R91, Delco 1107174. Note this starter can also be used for converting earlier tractors with mechanical starter buttons (starters Delco 1107093 and 1107067, IH part numbers 355794R91, 355794R92)to electronic starter with a key or momentary button switch. We do not have wiring instruction for this conversion. Replaces 1107174, 1108098, 360606R91, 370606R91 (Item #: 185608, Ref: 1107174) $305.00
Starter, 6 Volt - For C113 and C123 Gas engines on: A, B, C, Super A, Super C, 100, 130, 140, 200, 230. Replaces Delco 1107093, 1107067, 1108096. (Item #: 109655, Ref: SDR0092) $130.00
Starter, 6 Volt - New 6 volt starter for tractor models A, B, C, Super A, Super C, 100, 140 (to serial number 26800), 200, 230, 240. All 1952-1961 with C113 or C123 gas engines using starter switch mounted to the starter. Replaces Delco 1107093 and 1107067. Replaces IH part numbers 355794R91, 355794R92 Uses 593292C1 starter switch. If you have a solenoid on your starter, this is not the starter you need (see part number 1107174). This starter uses a saddle mounted push button switch. (Item #: 109655, Ref: 1107093R) $130.00
Starter Armature - Used with Delco Starter # 736C, 737B, 737G, 1107067, 1107074, 1107093, 1107169, 1107174, 1107404, 1107407, 1107408, 1107427, 1107430, 1107435, 1107444, 1107448, 1107462, 1107487, 1107490, 1107926, 1107999, 1108012, 1108016, 1108038, 1108041, 1108060, 1108080, 1108092, 1108097, 1108103, 1108112, 1108142, 1108158, 1108173, 1108174. Body OD: 2.921 inches, Communicator end OD: 0.563 inches, Drive End OD: 0.563 inches, Length: 12.728 inches, Communicating End to Bearing/Bushing Stop: 0.823 inches, Drive End to Bearing/Bushing Stop: 7.236 inches, Number of Comm. Bars: 23, Lam Stack Thickness: 2.685 inches, Set Screw and Keyway on Drive End. Replaces 1871662, 1878077, 1910938, 1B7705, 813555, 816163, 818002, D4100. (Item #: 182636, Ref: 1871662) $93.58
Starter - Delco Style DD (4009), Remanufactured, Delco Remy, 1107021, 55784D - For International / Farmall tractor models A, C, Replaces International OEM number 55784D, Replaces Delco Remy manufacturer number 1107021, Replaces manufacturer number 140-051, 4009, Delco Style: Direct Drive, Voltage: 6, Rotation: Counter Clockwise, Teeth: 10, (Item #: 203215) $441.62
Starter Drive - This Starter drive fits gas engines for the following models: A, B, C, H, M, Super A, Super C, Super H, W4, W6, Super M, 100, 130, 140, 300, 330, 340, 350, 200, 240, 400, 450 Replaces OEM# 1107021, 1107412, 1107606, 1107427, 1107174, 1107067, 1107444, 1107093, 1107448, 1108097, 1107408, 1108098, 1107886, 1108093, 1108080, 1108038, 1108041, 1108012, 1108173, 1108016, 1108174, 1108185. (Item #: 107059, Ref: 565549) $32.00
Starter Drive Housing - This Starter Nose Cone is used on Delco starter numbers 1107021, 1107060, 1107067, 1107093, 1107174, 1107427, 1107448, 1108096. Bushing is included. This part replaces Delco part numbers 1878661, 1887109, 1910093, 1943759 (Item #: 179382, Ref: 1878661) $75.01
Starter Drive, Improved Style - This improved style starter drive is a positive ratchet style. For A, B, C, H, M, Super M, 100, 130, 140, 300, 330, 340, 350, 200, 240, 400, 450, Super A, Super C, W4, W6 all using the following starters 1107021, 2207412, 1107606, 1107427, 1107174, 1107067, 1107444, 1107093, 1107448, 1108097, 11074808, 1108098, 1107886, 1108093, 1108080, 1108038, 1108041, 1108012, 1108173, 1108016, 1108174, 1108185. Ten tooth drive, counter clockwise rotation, Barrel Folo rubber cushion drive design, 15.9mm inside diameter, 39.6mm gear diameter, 95-109mm. (Item #: 112575, Ref: 565549-New) $59.94
Starter Nose Cone - This cast nose cone is used with starters that have saddle mount solenoids. Solenoid mount is not cast into this part. Bushing Included. Multi drilled and tapped for multiple applications. Used on Delco: 1107169, 1107358, 1107402, 1107407, 1107413, 1107414, 1107424, 1107434, 1107437, 1107439, 1107440, 1107443, 1107456, 1107458, 1107459, 1107542, 1107663, 1107682, 1107806, 1107813, 1107831, 1107958, 1107967, 1107976, 1108006, 1108009, 1108012, 1108038, 1108041, 1108060, 1108090, 1108621, 1108092, 1108103, 1108130, 1108142, 1108159, 1108165, 1109380, 1813397. Replaces Delco part numbers: 1813396, 1872960, 1874785, 1879052, 1914976, 1924299, 1924468, 1930639, 1935587, 1938304, 1959334, 1959773, 1963665 (Item #: 189672) $52.00
Starter Solenoid - Starter solenoid for 6 volt starters A, B, C, Super A, Super C, 100, 140, 200, 230, 240, 300, 340, 350, 400. All 1952-1961 with C113 or C123 gas engines using starter switch mounted to the starter. Replaces 25A266, DR1465. (Item #: 105670, Ref: 142364HA) $20.00
Starter Switch, Manual - Starter Switch, manual, saddle mount. For A, B, C, Cub, Cub Lo-Boy, Super A and AV, Super C, H, HV, Super H and HV, Super M and MV, Super W6 and WD6, 100, 130, 140, 200, 230. Saddle Mount, 2 mounting holes, 190 inside diameter. With 1-3/8 inch centers. Replaces Delco 1918405, 1932131, and OEM IH number 593292C1. (Item #: 105669, Ref: 1925781) $9.00
Terminal Clip - Light terminal plate with screws. For 200, 230, 300, 330, 350, 400, 450, 600, 650, A, B, C, H, HV, M, MD, O4, O6, ODS6, OS4, OS6, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super WD9, Super WDR9, Super A, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S (Item #: 117534, Ref: 79407H) $6.50
Tune-up Kit - This Tune-up Kit is for IH Distributors - NOT Delco. Complete Kit For: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 4, 400, 404, 424, 444, 450, 6, A, AV, B, BN, C, H, HV, M, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super A, Cub, Cub Lo-boy, Cub 154 Lo-Boy, Cub 185 Lo-Boy. All with 4 cylinder gas engines and IH distributor from 1951 through 1962. Contains: Points, Autolite Spark Plugs (AL386), Condenser, rotor. NOT FOR USE ON EARLY MODELS WITH A MAGNETO. (Item #: 111814, Ref: IHTK1) $31.00
Tune-up Kit - This Tune-up Kit is for Delco Distributors with clip help cap. 4 Cylinder kit includes Autolite spark plugs (Replaces Autolite AL386, AL388, AL3116 and Champion D10, D14, D16, RD16, D21, D23 plugs), points, condenser, and rotor. For tractor models with clip held Type Delco Distributor Caps. For tractor models A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDV, 4, Super 4, 6, Super 6, 9, Super 9, 354, B414. Verify correct spark plug replacement. Note, not for British Delco Distributors 7953342. (Item #: 173738, Ref: MFITK10) $27.30
Tune-up Kit - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, Cub 154, Cub 185, H, HV, M, MD, Super A, Super C, Super H, Super HV, Super M, Super MTA, 200, 230, 240, 300, 330, 340, 350, 400, 404, 450, 460, 560, Thread: 18 mm, (Item #: 181488) $40.10
Tune-up Kit, Basic - This basic tune-up kit is for 4 cylinder gas engines with battery ignition from 1951 thru 1962 with IH distributor (NOT for Prestolite), kit contains rotor, condenser, points, and proper point gap guage. For tractor models 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 444, 450, A, B, C, Cub 1962 and earlier, H, M, Super A, Super C, Super H, Super M, Super MTA, W4, W6. (Item #: 105572, Ref: ATK5BIR) $14.10
Voltage Regulator - Regulator, 6 volt, positive ground, saddle mount, 4 terminal. Replaces Delco cut outs 1116766 and 1116809 when used with conversion kit VRK1815. For tractor models Cub, Cub Lo-Boy, A, Super A, B, C, H, M. Replaces: 1118265, 1118305, 1118790, 1118786. (Item #: 105284, Ref: VR1813) $33.00
No Picture Wiring Harness - WIRE HARNESS switch to rear lights For A, B. (Item #: 161891, Ref: 30711DX) $36.50
Wiring Harness - For A, B. COMPLETE Wiring Harness. Restoration Quality. Harness covers entire tractor. Original cloth sewn harness. (Item #: 126782, Ref: R3716) $228.00
Wiring Harness Grommet - For International / Farmall tractor models A, B, C, H, HV, I4, I6, I9, M, MD, O4, O6, OS4, OS6, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, Replaces International OEM number 52062D, Mounts in amp box, Outer Diameter: 1.810", Inner Diameter: 1.246", (Item #: 126808) $5.50
Wiring Harness, Magneto Ignition - For use with voltage regulator-magneto ignition system only. Ignition wire harness fits: A, A1, AV, AV1. (Item #: 172792, Ref: 354231R92) $38.82

Engine Bearings
Main Bearings 0.030 - Main bearing set in 0.030. For C113 and C123 4-cylinder gas engines. (1 Kit used per engine). For tractor models A, AV, B, BN, Super A, Super AV, Super A-1, Super AV-1, C, Super C, 100, 130, 140, 200, 230, 240. Journal measures 2.095. YTO MBK113-030. Replaces 372116R91 and 7372116 (Item #: 106564) $75.01
Main Bearings .010 - Main bearing set in 0.010. For C113 and C123 4-cylinder gas engines. (1 Kit used per engine). For tractor models A, AV, B, BN, Super A, Super AV, Super A-1, Super AV-1, C, Super C, 100, 130, 140, 200, 230, 240. Journal measures 2.115. YTO MBK113-010. Replaces 376639R91 and 7376639. (Item #: 106562) $57.00
Main Bearings .020 - Main bearing set in 0.020. For C113 and C123 4-cylinder gas engines. (1 Kit used per engine). For tractor models A, AV, B, BN, Super A, Super AV, Super A-1, Super AV-1, C, Super C, F12, F14, 100, 130, 140, 200, 230, 240. Journal measures 2.105. YTO MBK113-020. Replaces 376642R91 and 7376642. (Item #: 106563) $86.75
Rod bearings - Rod bearing in .030. For C113 and C123 Gas engines. Journal Measure 1.720 inches. For tractor models A, AV, B, BN, Super A, Super AV, C, Super C, 100, 130, 140, 200, 230, 240. Replaces YTO CRK113-030, 356305R1, and 7356305. Sold individually. (Item #: 106448) $16.40
Rod Bearings - Rod bearing in .002. For C113 and C123 Gas engines. Journal Measure 1.748 inches. For tractor models A, AV, B, BN, Super A, Super AV, C, Super C, 100, 130, 140, 200, 230, 240. Replaces YTO CRK113-002, 360218R11, and 7356306. Sold individually. (Item #: 106445) $14.90
Rod Bearings - Rod bearing in .020. For C113 and C123 Gas engines. Journal Measure 1.730 inches. For tractor models A, AV, B, BN, Super A, Super AV, C, Super C, 100, 130, 140, 200, 230, 240. Replaces YTO CRK113-020, 376638R11, and 7376638. Sold individually. (Item #: 106447) $13.40
Rod Bearings - Rod bearing in standard. For C113 and C123 Gas engines. Standard Journal Measure 1.750 inches. For tractor models A, AV, B, BN, Super A, Super AV, C, Super C, 100, 130, 140, 200, 230, 240. Replaces YTO CRK113-STD, 356304R11, and 7356304. Sold individually. (Item #: 106444) $12.40
Rod Bearings, .010 - Rod bearing in .010. For C113 and C123 Gas engines. Journal Measure 1.740 inches. For tractor models A, AV, B, BN, Super A, Super AV, C, Super C, 100, 130, 140, 200, 230, 240. Replaces YTO CRK113-010, 376636R11, and 7376636. Sold individually. (Item #: 106446) $13.30
No Picture Rod Bearing Set, 4 Cylinder, Standard - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, Compatible with International Engine (s) C113, C113 (gas), C123, C123 (gas), Standard Journal Measure 1.750 inches, (Item #: 183958) $46.00

Engine Gaskets
Complete Gasket Set with Seals - Overhaul gasket set For tractor models 130, 140, 22, 230, 240, 62, 76, 81, A, A1, AV, AV1, B, BN, C, Super A, (U-2, U-2A up to serial number 22113), (330, 340, 404 with C135). Replaces FS3150. (Item #: 106715, Ref: OGS113) $69.00
Crank Seal, Front - For tractor models 100, 130, 140, 200, 22, 230, 240, 62, 76, 81, A, A1, AV, AV1, B, BN, C, Super A, Super A serial number 255418-310299, Super A serial number 310300>, Super AV, Super AV serial number 255418-310299, Super AV serial number 310300>, Super C, U-2 swrial number <22113, U-2A serial number <22113. (Item #: 172671, Ref: 389407R92) $11.60
No Picture Crank Seal, Rear - Fits, 100, 130, 140, 200, 22, 230, 330 serial number <100500, 340 serial number <100500, 62, 76, 81, A, A1, AV, AV1, B, BN, C, Super A, Super A serial number 255418-310299, Super A serial number 310300>, Super AV, Super AV serial number 255418-310299, Super AV serial number 310300>, Super C, U-2 serial number <22113, U-2A serial number <22113. (Item #: 106651, Ref: 24425D) $19.20
Front Crankshaft Seal - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, Super A, Super C, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504, Compatible with International Engine (s) C60 (Gas and LP), C113 (Gas and LP), C123 (Gas and LP), C135 (Gas and LP), C146 (Gas and LP), C153 (Gas and LP), Replaces International OEM number 379620R92, 378193R91, 350708R1, 355769R1, 46179DC, (Item #: 106638) $14.80
No Picture Full Gasket Set - For A, Super A, B, C, Super C, F-14, 100, 130, 140, 230, 240 with Water Pump Gasket (Item #: 106716, Ref: FS3150) $97.00
Gasket, Manifold, Pack of 2 - Used with 251175R1 Manifold. Fits Models: A, B, C, Super C, Super AV, AV, BN, T340, T5, Super A, 100, 130, 140, 200, 240, 330, 340, 404, 424, 444, A1, T4B, AI, All with 113, 123, 135, 146 and 153 CID Gas, LP or Distallate engines. Price is for two. Replaces 24520D, 24520DA, 352014R1, 48696D, 48696DA (Item #: 101551, Ref: 352014R1) $12.00
Gasket Set Upper - For early engines without a water pump. For C113 Gas engine in models: A, AV, B, BN, C, Super A, Super AV Only Fits 9 Stud Cylinder Head, not the 14 Stud. (Item #: 106676, Ref: 354474R95) $34.00
Head Gasket - Head gasket for 130, 140, 22, 230, 240, 62, 76, 81, A, AV, A1, AV1, B, BN, C, Super A, Super AV - all with C113 engine. (Item #: 168314, Ref: 366301R11) $35.40
Liner Sealing Ring - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, Compatible with International Engine (s) C113, C123, Replaces International OEM number 24434D, Sleeve OD: 3.30", (Item #: 128621) $5.20
Manifold Gasket Set - For International / Farmall tractor models A, B, C, Super A, Super C, 100, (Item #: 101543) $8.50
Oil Pan Gasket - For 140, 130, 100, 140, 300, 22, 230, 240, 330, 340, 62, 76, 81, A, A1, AV, AV1, B, BN, C, Super A, SUPVER AV, Super C, - ALL WITH C113 OR C123 ENGINES. (Item #: 106698, Ref: 43458DB) $8.10
Oil Seal - Fits: [A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240 (use as a flat belt pulley shaft seal)], [H, HV, Super H, Super HV (use as a transmission counter shaft front seal)], [O4, W4 (Used as a brake shaft oil seal)]; The seal measures 1.375 inches inside diameter, 2.110 inches outside diameter, 0.315 inches wide. Replaces: 356502R91, 356503R91, 358781R91, 358820R91, 367810R91, 369146R91, 43308D, 43660D, 48308D, 48954D, 71700C1, 71701C1. (Item #: 152182, Ref: 71701C1) $11.40
Rear Crankshaft Seal Kit - Fits tractor models A, AV, B, BN, C, F12, F14, I12, I14, O12, O14, W12, W14 (2-piece rear felt seal ONLY fits as a rear crankshaft seal), Super A, Super A-1, Super AV, Super AV-1, Super C 340 (gas, up to engine serial number 100500), 100, 130, 140, 200, 230, 240, 330. Replacement part number and kit contents: (2) 24425D, 24425DA felt seals, (2) 43447D, 43447DA seal retainer center gaskets, (1) 43448D seal retainer to block gasket, (4) 43445D seal plate felt plugs, and (4) 43446D, 43446DA seal retainer plate gaskets. (Item #: 182488, Ref: IHS2416) $21.40
Timing Cover Gasket Set - This Timing Cover Gasket Set contains: Governor housing gasket, Water pump plate gasket, Fan bracket gasket, Timing cover gasket, Front crankshaft seal with seal saver and Lower water outlet gasket. Use on C113, C123, C135, C146, and C153 Gas or LP engines. Fits A, AV, B, BN, C, Super A, Super AV, Super C, 100, 130, 140, 200, 230, 240, 2404, 2424, 2444, 2504, 330, 3514, 404, 424, 444, 504. Replaces OEM part numbers: 45875D, 375745R1, 375745R2, 43294D, 43294DA, 46179D, 46179DC, 43442D, 49177D, 378193R91, 46871D, 68104C1, 68104C2. (Item #: 182535, Ref: 46179DKit) $32.00
Valve Cover Gasket - This Valve Cover Gasket is used on Gas Engines; C113, C123, C135, C146, C153. It replaces OEM/Original part numbers 43378DB, 43378DD, 43378DE. (Item #: 128613, Ref: 43378DE) $10.40
Valve Seals - Valve Guide Seal - Positive Type (Item #: 183858, Ref: 386192R1) $3.30

Engine Rebuild Kits
Basic Engine Overhaul Kit, Less Bearings with Flat Head Pistons - Basic Engine Kit, Less Bearings, for A and AV, B and BN, Super A and AV to serial number 310299, C. Cylinder sleeves are 3-5/16 (3.3125) inches O.D. at the seal. (C113 CID 4-cylinder Gas). For tractors with flat head standard compression pistons. Kit contains sleeves and sleeve seals, pistons and piston rings (overbore from 3 inch to 3-1/8 inch), pins and retainers, complete gasket set with crankshaft seals. ENGINE BEARINGS ARE NOT INCLUDED. (Item #: 131096, Ref: BEKH1150-LCB) $390.00
Basic Engine Overhaul Kit, Less Bearings with Stepped Head Pistons - Basic Engine Kit, Less Bearings for A and AV, B and BN, Super A and AV to serial number 310299 (C113 CID 4-cylinder Gas). For tractors with stepped head high compression pistons. Kit contains sleeves and sleeve seals, pistons and piston rings (overbore from 3 inch to 3-1/8 inch), pins and retainers, complete gasket set with crankshaft seals. Sleeves are 3-5/16 inch outside diameter at the seal. For engines without factory water pump. ENGINE BEARINGS ARE NOT INCLUDED. (Item #: 130577, Ref: BEKH1154-LCB) $444.00
Basic In-Frame Engine Kit, with Flat Head Pistons - For A and AV, B and BN, Super A and AV to serial number 310299, and C. Kit contains complete sleeve and piston kit with rings, pins and retainers (overbore 3 inch to 3-1/8 inch, block seal land ID 3.311 inches), upper gasket set (with head gasket) and pan gasket. (Item #: 184556, Ref: BIFH1150) $334.00
Basic In-Frame Engine Kit, with Stepped Head Pistons - For A and AV, B and BN, Super A and AV to serial number 310299 and C. (C113 CID 4-cylinder Gas). For tractors with stepped head high compression pistons. Kit contains complete sleeve and piston kit with rings (overbore from 3 inches to 3-1/8 inches, block seal land ID 3.311 inches), pins and retainers, upper gasket set (with head gasket), and pan gasket. (Item #: 184554, Ref: BIFH1154) $344.00
Engine Overhaul Kit, Comprehensive, Less Bearings with Flat Head Pistons - Overhaul kit, less bearings. For A and AV, B and BN, Super A and AV to serial number 255417 (C113 CID 4-cylinder gas). For tractors with flat head standard compression pistons. Kit contains sleeves and sleeve seals, flat head pistons and piston rings (overbore from 3 inch to 3-1/8 inch), pins and retainers. Complete gasket set with crankshaft seals. Intake and exhaust valves, valve keys, guides and springs. ENGINE BEARINGS ARE NOT INCLUDED. Valve length is 4-25/32 inch. (Item #: 187185, Ref: EOK1150-LCB) $849.00
Engine Overhaul Kit, Comprehensive - Less Bearings - with Stepped Head Pistons - Overhaul kit for A and AV, B and BN, Super A and AV to serial number 255417 (C113 CID 4-cylinder gas). For tractors with stepped head high compression pistons. Contains sleeve and piston kit (sleeves, pistons and rings, pins and retainers, overbore from 3 inch to 3-1/8 inch). Complete gasket set. Valve parts: (intake and exhaust valves, springs, guides and keys). IMPORTANT: specify the part numbers on your old intake and exhaust valves to ensure that correct replacements are sent. (Item #: 186985, Ref: EOK1154-LCB) $745.18
Engine Rebuild Kit - Less Bearings - 3.25" Overbore, C113, C123 - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, Compatible with International Engine (s) C113 (Gas), C123 (Gas), 3.25" overbore, Flat Top Pistons, Lower Sleeve O.D. 3.43", Kit includes: Pistons, Piston Ring Set, Liners and Gasket set with Crank Seals, Kit does not include piston pin bushings, connecting rod or main bearings, For piston pin bushing use Item #: 106564, (Item #: 131097) $444.00
Engine Rebuild Kit - Less Bearings - 3.437" Liner Seal I.D., C113 - For International / Farmall tractor models A (with block 354898R1-R4), B (with block 354898R1-R4), C (with block 354898R1-R4), Super A (s/n 310300-356000), Compatible with International Engine (s) C113 (gas), Bore: 3.125", 3.437" liner seal land inside diameter, Engines without water pump conversion, Kit includes: Pistons, Piston Ring Set, Liners and Gasket set with Crank Seals, Kit does not include piston pin bushings, connecting rod or main bearings, For piston pin bushing use Item #: 106564, (Item #: 130579) $467.00
Valve Overhaul Kit - C113 4-cyl Gas - Fits A, AV, B, BN, Super A, AV to serial number 255417 valve length 4-25/32 inch, (4 cylinder Gas/C113). Kit includes valves, valve springs (for non-roto exhaust valve), valve keys, and valve guides. Replaces exhaust valves marked 42025DA and intake valves marked 42024D. (Item #: 172565, Ref: VOKH113) $191.00
Valve Overhaul Kit - C113 and C123 Gas - Fits Super A, AV serial number 255418 to serial number 310299, C and Super AI, AV1 serial number 310300 and up, Super C, 100 and 200. Valve Length 4-57/64 inch, (Gas 4 cylinder, C113, C123 CID). Replaces exhaust valves marked 57798D and intake valves marked 57797D. Kit includes valves, valve springs (for non-roto exhaust valve), valve keys, valve guides. (Item #: 183984, Ref: VOKH123) $140.00
Valve Train Kit - For 113 CID Gas Engine (valve length 4.83 inch). Models: 130, 140, 22, 230, 240, 62, 76, 81, A, AV, A1, AV1, B, BN, C, Super A, Super AV, U-2 serial number <22113, U-2A serial number <22113. Kit includes 4 intake valves, 4 exhaust valves, 8 valve springs, 8 valve guides, 16 valve keys. (Item #: 172565, Ref: VTK113) $191.00

Engine Parts
Camshaft Timing Gear - 66 teeth. For tractor models (100, 130, 140, 200, 230, 240, Super C all with 123 CID engine), (330, 340, 404 all with 135 CID engine), (424 with 146 CID engine), (444, 504 with 153 CID), (A, AV, B, BN, C, Super A, Super A1, Super AV, Super AV1 with 113 CID engine). Replaces 375712R1, 6779DB. (Item #: 111038, Ref: 375712R1) $92.00
Crankshaft Gear, Used - For International tractor models A, B, C, Super A, Super C, 200, 230, 240, 330, 340, 404, 424, 504, 2404, 2424, 2504, Compatible with International Engine(s) C123, C135, C146, C153, Compatible with International Hay Cutting(s) 201, Replaces International OEM nos 46870DA, Replaces Casting nos 46879DA, 33 Teeth, Inside Diameter: 1.25", Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 497149) $89.01
Crankshaft Pulley - Crankshaft Pulley For A, B, C, Super A, Super C, 100, 130, 200, 230. Press fit. Not drilled/tapped for setscrew, (early tractors used a setscrew to retain pulley to crankshaft, customer would have to drill and tap this pulley). This pulley is balanced and has timing marks. Replaces: 251589R91, 6502DB, 6502DC, 6502DX (Item #: 100791, Ref: 6502DC) $72.00
No Picture Crankshaft, Remanufactured, 46402DB - For International / Farmall tractor models A, B, Compatible with International Engine (s) C113, Replaces Casting number 46402DB, Our remanufactured crankshafts are cleaned, magnafluxed, measured and reground if necessary, the journals are then polished., (Item #: 200227) $475.01
Crankshaft Timing Gear - 33 teeth, used in C113, C123, C135, C146, and C153 Engines. For tractor models A, Super A, AV, Super AV, B, BN, C, Super C, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504. (Item #: 121687, Ref: 46870DA) $65.00
No Picture Cylinder Head, Remanufactured, 6716DA - For International / Farmall tractor models A, B, Super A (gas), Replaces International Casting number 6716DA, Engines 113, 123, Cylinders: 4, Not a welded head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 205486) $650.01
No Picture Cylinder Head, Remanufactured, 9052DA - For International / Farmall tractor models A (Gas), B, Super A, Replaces International Casting number 9052DA, Engines 113, 123, Cylinders 4, Casting No. 9052DA, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200186) $550.01
Cylinder Head, Used - For International tractor models A (Gas), B, Super A, Replaces International Casting number 6716DA, Engine(s): 113, 123, Cylinders: 4, Our used cylinder heads have been visually inspected for cracks, Cylinder head may require further cleaning, inspection, or machining before use, For a Remanufactured version of this part use Item #: 205486, Additional Handling and Oversize Fees Apply To This Item, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 405486) $321.01
Cylinder Kit - For International / Farmall tractor models A, B, C, F12, F14, Super A, W12, 130, 140, 230, 240, Replaces International OEM number 366289R91, (Item #: 168657) $94.00
Governor Arm, Rockshaft - For tractor models (200, 230, 240 serial number up to 65000 with C123 engine), A, A1, AV1, B, C, Super A, Super AV, Super C. (Item #: 105380, Ref: 6507DA) $39.10
Governor Assembly - For A, Super A, B, C, Super C, 100, 130, 140, 200, 240, 330, 340, 404. OEM number 375778R11, 374710R1, 356746R91, 356745R91. Does NOT include housing. (Item #: 105375, Ref: R0612) $167.00
Governor Spring - This Governor Spring is used internally in the following tractors: A, AV, B, BN, Super A, Super A1, Super AV, Super AV1, 100, 130, 2404 (With C-113, C-123 or C-135 engines), 404. It replaces: 46944DA (Item #: 179295, Ref: 46944DA) $12.40
No Picture Governor Thrust Bearing Assembly - This 3 piece bearing assembly slides onto the governor assembly. For models cub, A, B, C, Super C, 560, Super AV, 184, AV, Bn, Cub Lo-Boy, Super A, 100, 130, 140, 154, 185, 200, 230, 240, 330, 340, 404, 424, 444, 460, 504. Also replaces 55314D. (Item #: 184444, Ref: 43481D) $52.00
Hand Starting Crank, with Spinner - For tractor models (A, B, C, Super A, ALL WITH THE C113 ENGINE), (200, 230, 340, 404, 504 all with tricycle front). Starting Hand Crank with Spinner. Measures 13 1/2 inches to the first bend Longest Straight Section. (Item #: 122095, Ref: 53385DBX) $69.00
Pushrod - Fits A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, U2, U2A, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504 (all with C113, C123, C135, C146, C153 gas/LP engines) 10.762 inch length, 0.310 inch tube diameter . Replaces: 360213R91, 357548R1, 47386D, 47385D. (Item #: 182498, Ref: 47385D) $43.00
No Picture Push Rod, Used - For International tractor models A, B, BN, C, Super A, Super AV, Super C, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504, Compatible with International Engine(s) C123, C135, C146, C153, Compatible with International Hay Cutting(s) 201, Replaces International OEM number 357548R1, For a new version of this item use Item #: 182498, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 463344) $24.01
Ring Gear,Flywheel - For tractor models A, B, C, Super A, Super C, 100, 130, 140, 200, 240. Gear has 90 teeth, 10.495 inch inside diameter and 11.435 inch outside diameter, .50 inches wide. (Item #: 103906, Ref: 55755DB) $32.50
No Picture Valve, Exhaust - For tractor models A, AV, B, BN, Super A, Super AV, to serial number 255417. (flat head compression piston) (cylinder sleeve 3-5/16 inch outside diameter at seal) (valve length 4-25/32 inch). SOLD by the EACH. (Item #: 128739, Ref: 42025DA) $20.10
Valve, Exhaust - For Models: A, AV, Super A and Super AV serial number 255418 to serial number 310299, and C. (flat head compression piston) (cylinder sleeve 3-5/16 inch outside diameter at seal) (1.160 inch head diameter, 4.940 inch length, 45 degree). Sold single. (Item #: 128524, Ref: 57798D) $13.40
Valve Guide - Valve guide for tractor models 100, 130, 140, 200, 22, 230, 240, (330, 340 serial number 100500 and before), 62, 76, 81, A, A1, AV, AV1, B, BN, C, Super A, Super AV, Super C, (U2, U2A serial number less than 22113). Price shown is for each, sold only in multiples of 8 items. (Item #: 128646, Ref: 356583R21) $4.60
Valve, Intake - Intake valves for Models: A, AV, B, BN, Super A, Super AV, to serial number 255417. (cylinder sleeve 3-5/16 inch outside diameter at seal) (valve length 4-25/32 inch). Price shown is for each. (Item #: 128522, Ref: 42024D) $12.90
Valve, Intake - For tractor models: A, AV, Super A and Super AV serial number 255418 to serial number 310299, and C. (flat head compression piston) (cylinder sleeve 3-5/16 inch outside diameter at seal) (1.340 inch head diameter, 4.940 inch length, 45 degree). Sold single. (Item #: 128523, Ref: 57797D) $10.80
Valve Key, Intake and Exhaust, 1/2 - Sold per 1/2 valve, order 2 per valve. For tractor models 100, 130, 140, 200, 22, 230, 240, 300, (330, 340 serial number less than 100500), 350, 62, 76, 81, A, A1, AV, AV1, B, BN, C, H, HV, O4, OS4, Super A, Super AV, Super C, Super H, Super HV, Super W4, (U2, U2A serial number less than 22113), W4. Replaces 42026D, 70206880, 42026DGV, 500327, 70206880GV, 7HA6518GV, A30004, G11929. Sixteen required per engine. (Item #: 107088, Ref: 7HA6518) $0.60
No Picture Valve Service Kit - Cylinder HEAD Service KIT For 100, 200, A, AV, B, BN, C, Super AV, Super C, Super A. Contains: springs, guides, locks, (no valves). (Item #: 131579, Ref: VSKH113) $192.00
Valve Spring - Used on valves with length of 5-5/16 inch. For tractor models 100, 130, 140, 200, 22, 230, 240, 62, 76, 81, A, AV, A1, AV1, B, BN, C, H, HV, O4, OS4, Super A, Super AV, Super AV1, Super C, (U2, U2A serial number less than 22113), W4. 8 Used Per Tractor. Sold individually. (Item #: 128518, Ref: 24544DA) $3.30

Engine Pistons and Sleeves
Cylinder Kit - For International / Farmall tractor models A, B, C, Super A, Super C, 100, 200, Compatible with International Engine (s) C113 (Gas, LPG), C123 (Gas, LPG), Replaces International OEM number 374493R93, 3.125" bore, Dome Top Piston, (Item #: 166745) $103.00
Pin Bushing - This Piston Wrist Pin Bushing Is used on 113 and 123 Gas and LP Engines. 0.909 inch I.D. 0.993 Inch O.D. 1.216 inch overall length. Pin Bushings require honing after installation. Replaces: 24415D, 64508D (Item #: 108092, Ref: 64508D) $10.00
Piston Sleeve - Fits 113 CID, 123 CID 4 cylinder gas engines with 3 1/8 inch bore (3 inch bore no longer available). 3.31 inches OD sleeve at seal. Models: 130, 140, 22, 230, 240, 62, 76, 81, A, AV, A1, AV1, B, BN, C, Super A, Super A serial number 255418-310299, Super AV, Super AV serial number 255418-310299, U-2 serial number <22113, U-2A serial number <22113. Pricing is per liner. 3.31 inch outside diameter sleeve at seal. (Item #: 172546, Ref: SW52) $23.30
Sleeve and Piston - This sleeve and piston is for one cylinder and is stepped head piston. For Super A and Super AV to serial number 310299, A, AV, B, BN, C. For C113 Gas Engine. Contains: sleeve, stepped head piston and rings, pin and retainers. Overbore from 3 inch to 3-1/8 inch. 3-15/16 inch OD on the sleeve at the seal. Sold per piston. 4 used per engine. (Item #: 166570, Ref: PK154) $84.00
Sleeve and Piston Kit 3 1/8 Bore - This sleeve and piston kit is for 1 hole using a Flat Head Piston on 113 CID, 123 CID 4 cylinder gas engine models: 130, 140, 22, 230, 240, 62, 76, 81, A, AV, A1, AV1, B, BN, C, Super A, Super A serial number 255418-310299, Super AV, Super AV serial number 255418-310299, U-2 serial number <22113, U-2A serial number <22113. (Item #: 184584, Ref: SK260) $132.00
Sleeve and Piston Kit 3 1/8 Bore - This sleeve and piston kit is for 1 hole using a Stepped Head Piston in 113 CID, 123 CID 4 cylinder gas engine models: 130, 140, 22, 230, 240, 62, 76, 81, A, AV, A1, AV1, B, BN, C, Super A, Super A serial number 255418-310299, Super AV, Super AV serial number 255418-310299, U-2 serial number <22113, U-2A serial number <22113. (Item #: 166570, Ref: SK265) $84.00
Sleeve and Piston Kit, Flat Head Pistons - This sleeve and piston kit is for 1 engine (4 holes). For tractor models A and AV, B and BN, Super A and AV to serial number 310299, C, 130, 140, 230, 240. For C113 and C123 Gas engines. Contains (4) sleeves, (4) flat head pistons and rings, pins and retainers. Overbore from 3 inch to 3-1/8 inch. (Item #: 184099, Ref: PK150) $389.00
No Picture Sleeve Seal Rings - Sleeve seal o-ring kit for 1 cylinder on 113 or 123 CID Gas engines with a 3 5/16 inch diameter at the seal for models: A, AV, AV1, B, BN, C, Super A, Super AV, 130, 140, 230, 240. Replaces 367799R1, 354881R1, 367799R1 (Item #: 173279, Ref: SRK713) $5.50