International Harvester / Farmall MTA Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Pedal Shaft Seal - This brake pedal shaft seal has a 1.125 inch Inside Diameter, a 1.832 inch Outside Diameter and is .25 inch wide. It Fits: 230, 3514, B-450, C, H, HV, I6, ID6, M, MD, MDV, MTA, MTAV, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6, Super W6TA, Super WD6TA, W4, W6, W6TA, WD6, 200, 240, 300, 330, 340, 350, 3600A, 3616, 400, 404, 450, 460, 504, 544, 560, 606, 656, 660, 664, 666, 686, 400, W400, 450, W450, 8000, Hydro 70, Hydro 86. Replaces: 354514R91, 360076R92, 364471R91, 380959R91, 380960R91, 47169A, 555397R91, 581646R91, U17944, 476838 (Item #: 153586, Ref: AB2578R) $15.50
Disc Brake Boot - This Boot is used on Tractors with Disc Brakes. Used on Farmall MTA, ODS6, OS6, Super M, Super MD, Super MDV, Super MV, Super W6, Super W6TA, Super WD6, 400, 450. Replaces 357044R1 (Item #: 112347, Ref: 357044R1) $6.70

Clutch
Clutch Bearing - Release bearing for tractor models 2656, 300, 330, 340, 350, 400, 450, 460, 504, 544, 560, 606, 656, 660, 664, 666, 686. Inside diameter 2.0625 inches, outside diameter 3.625 inches, width .7969 inches. Please verify measurements before ordering. Replaces 18567D, 362028R91, 362028R92, 55211D, 55212D (Item #: 107007, Ref: N1087) $21.00

Cooling System
Radiator - Made of copper and has a hole in radiator for the steering shaft. For tractor models M, Super M, MD, Super MD, MTA, Super MTA, W6, Super W6, WD6. Note: If replacing a NON-pressure radiator, you will have to replace the temperature gauge with part number 67135D. (gauge NOT supplied). Weight 36 pounds. Replaces 352629R92. For radiator cap order part number 67448DD. (Item #: 101709, Ref: 351798R92) $485.00
Thermostat - This 160 degree Long Neck Thermostat. Fits the following tractor models: H, HV, M, MD, MDV, MTA, MV, O4, O6, Super H, Super HV, Super M, Super MD, Super W6, W4, W6, W9, 300, 350 Gas, 400, 450, 560 Diesel, 656 Diesel, 660 Diesel, and 706 Diesel. It does not come with a gasket. Replaces part numbers 313942R91, 313942R92, 315838R91, 317668R91, 37634DA, 261514R92. (Item #: 110010, Ref: R1852) $38.50
Water Block Drain Plug, Winged - Plug 3/8 inch pipe thread, has "IH" and part number stamped in it, cast iron with zinc plating. For tractor models A, AV, Super A, Super AV, Super A1, Super AV1, B, BN, C, H, HV, Super H, Super HV, I4, I6, ID6, I9, ID9, M, MD, MV, MDV, Super M, Super MD, Super MV, Super MDV, MTA, 04, 0S4, 06, 0S6, ODS6, T6, T340, TD6, T9, TD9, W400, W450, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650 (Gas/Diesel), serviceable for Cub, Cub Lo-Boy. (Item #: 178066, Ref: 45314DC) $12.90

Drive Train
Oil Seal - Fits: [A, A-I, A1, AV, AV-1, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 2404, 404 (Top Transmission Shaft Front Seal)], [B-250, B-275, B-276, B-414, 2300, 2300A, 2424, 2444, 3414, 3444, 354, 364, 384, 424, 434, 444 (Bull Pinion Shaft Bearing Retainer Seal)], [Cub, Cub Lo-Boy, 154, 184, 185 (Final Drive Upper Pinion Shaft Seal)], [M, MD, MDV, MV (Transmission Counter Shaft Front Seal)], MTA (Front Wheel Seal; with single front 900 x 10 wheel), [O4, OS4 (PTO Output Shaft Seal; serial number 2159 to 9300)], [Super M, Super MD, Super MDV, Super MV (Transmission Counter Shaft Front Seal; up to serial number F52627 and up to serial number L51241)], W4 (PTO Output Shaft Seal; serial number 786 to 9300). Replaces: 21969D, 264694R91, 287440R91, 3043788R91, 3043788R92, 358765R91, 358784R91, 358808R91, 358823R91, 381907R91, 42177D, 43278D, 50839D, 530969R91, 703907R91, 703908R92, A29424. (Item #: 178204, Ref: 381907R91) $6.00
Rear Saddle - When using this rear saddle a wide front can be installed. For tractor models M, MD, MTA, Super M, 450, Farmall 400. (Item #: 110604, Ref: 360406R1) $209.00
Reverse Idler Gear Bushing - This Bushing Measures 1.245 inches inside diameter, 1.375 inches outside diameter, 1.486 inches long. Sold individually. This bushing has a superior dimpled brass inner design to retain grease. No need for an external grease hole. Note: Must be honed or reamed to size when installed. Used on the following as a reverse idler gear bushing: 400, 450, 560, 660, B-450, BM, BMD, M, MD, MDV, MTA, MV, O6, ODS6, SBM, SBMD, Super M, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W6, Super WD6, W400, W450, W6, W6TA, WD6, WD6TA; Replaces: 48841D (Item #: 109669, Ref: 48841D) $13.50
Shift Lever Repair Pin Kit - For International / Farmall tractor models B250, B275, B276, B414, H, HV, I4, I6, I9, M, MD, MTA, O4, O6, OS6, Super H, Super HV, Super M, Super MTA, Super W6, W4, W6, W400, W450, WD6, WD9, 300, 330, 340, 350, 354, 364, 384, 400, 424, 434, 444, 450, 460, 504, 560, 606, 660, 2300, Replaces International OEM number 256918R1, 172529, 256919R1, 259918R11, 310662R11, 310664R11, 34878D, 357003R1, 40465DA, 40466DA, 705650R1, (Item #: 167881) $29.00

Electrical System
Distributor - New and complete distributor comes with a 32 tooth gear, and is for tractor models: A, AV, B, BN, C, H, HV, M, MV, Super A, Super AV, Super C, Super H, Super M, Super MTA and other IH equipment with International Distributors. Replaces: 107296C91, 107299C91, 107302C91, 107304C91, 353890R91, Distributor Housing Casting Number: 353898R11, 354900R91, 357935R91, 362473R91, 362722R91, 364653R91, 364696R92, 366928R91, 372712R91, 380622R91. Uses IH points (included). (Item #: 124839, Ref: 107304C91) $114.00
Distributor Drive Housing - This is a new distributor drive housing with an opening for tachometer drive. It is used to change from a magneto to a distributor or to add a tachometer drive to your tractor. The tachometer drive parts (tachometer drive assembly part number 369695R1, tachometer cable connector housing, part number 369692R1 and 363817R1, connection housing plate) or tach. Drive blockoff plate are sold separately. NOTE: Will also work on tractors without tach drive by ordering number 363764R1 block off plate. Use with 107304C91 distributor when replacing a magneto. fits tractor models A, A1, AV, AV-1, B, BN, C, Cub, Cub Lo-Boy, H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W9, W4, W6, W6TA, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 2504, 300, 330, 340, 3444, 350, 3514, 404, 424, 444, 504, 400, 600, 650 450. Replaces: 363749R91, 363763R11. (Item #: 178938, Ref: 363749R91) $107.00
Distributor Drive Housing, Used - For International tractor models C, M, MD, MTA, Super A, Super C, 200, 230, 240, 300, 330, 340, 350, 400, 424, 450, 504, 2404, 2424, 2504, Replaces International OEM number 363763R11, With Tachometer Drive Hole, For a new version of this item use Item #: 178938, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 429775) $65.01
Distributor Dust Cover - Fits early Delco Distributor with Clip Held Cap. For tractor models (A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super HV, M, MV, Super MV, MTA. All with Delco Vertical Conversion Distributor 1111411). (Item #: 103153, Ref: 1900119) $9.00
Distributor Gear - This Distributor Gear has 32 teeth. It is used on IH Distributor 353898R11. Replaces original part numbers 353902R1, 531461R91 (Item #: 111179, Ref: 353902R1) $31.40
Distributor Shaft Bushing and Shim Kit - Delco Distributor Shaft Bushing and Shim Kit. Fits A, A-I, A1, AV, AV-1, B, BN, C, H, HV, I4, I6, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, T6, U2, U2A, U4, U6, W4, W6 all with Delco vertical conversion distributor 1111411. Replaces: washer: 811913, shim washer: 810074, 810078, bushing: 1909003, 1952334 (Item #: 178103, Ref: ABC3007) $29.50
Distributor Shaft Bushing and Shim Kit - International Distributor Shaft Bushing and Shim Kit. Fits tractor models A, A1, AV, AV1, B, BN, C, Cub, Cub Lo-Boy, H, HV, M, MTA, MTAV, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 300, 330, 340, 3444, 350, 3514, 400, 404, 424, 444, 450, 504, 600, 650. Replaces: 252739R1, 352298R1, 353899R1, 353921R1, 373577R91, 86637641. This is a 5-piece kit. The length is 2.006 inches. (Item #: 178766, Ref: IHS3166) $44.80
Distributor Terminal Screw - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a zinc plated Terminal Screw. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. Replaces International part number 353907R1 (Item #: 118472, Ref: 353907R1) $7.80
Distributor Terminal Screw Insulator - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a spring anchor terminal insulator. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. (Item #: 118473, Ref: 353906R1) $7.20
Distributor with base less tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2404, 2424, 2444, 2504, 3444, 3514, Compatible with International Combine (s) 105, 203, Compatible with International Construction and industrial models T6, T340, 500, Without tachometer drive and with base, Includes new distributor cap, points, condenser, 6V Coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203588) $235.01
No Picture Generator - Delco Style (9718), Remanufactured, Delco Remy, 1100501 - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, I9, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, Compatible with International Combine (s) 101, 140, 151, Compatible with International Construction and industrial models T6, Compatible with International Baler (s) 37, 47, 57, Replaces Delco Remy manufacturer number 1100501, Replaces manufacturer number 9718, 340-21, 92-01-3050, Delco Style, Voltage: 6, Rotation: Clockwise, Amperage: 25, Regulator: External, (Item #: 203178) $408.38
H4 Magneto Pinion Driven Gear - This gear has 24 teeth and measures: 0.380 inch inside diameter, 0.759 inch outside diameter, 1.075 inch gear outside diameter, 0.952 inch overall height. It is used on H4 Magnetos. (Item #: 183878, Ref: 49420DX) $21.98
Ignition Tune-up Kit, Basic, Delco Clip Held Cap - Ignition kit For Delco ONLY distributor with CLIP held cap. VERIFY DISTRIBUTOR NUMBER TO ENSURE FIT. Contains points, condenser, and rotor. For tractor models A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDV, 4, Super 4, 6, Super 6, 9, Super 9, 354, B414, I4, I6, MTA, MV, O4, O6, T6, U2, W4, W6. For Delco distributor numbers 1111716, 1112583, 1112589, 1112557, 1112570, 1112585, 1111722, 1111737, 1112583. Not for IH Distributors. (Item #: 103151, Ref: ATK1DCR) $9.80
Magneto - This is a New Wico Magneto used on Farmall / IH Models: A, AV, B, BN, C, H, HV, I9, M, MTA, MTAV, MV, O4, O6, OS6, Super A, Super C, Super H, Super M, W4, W6, W6TA, 100, 130, 200, 230, 300, 350, 400, 450, 600, 650. It is also used on some industrials and power units. (Item #: 180178, Ref: XH1344) $558.00
Magneto Gasket Set - This magneto gasket set is for H4 Magnetos. It contains; Coil cover gasket 47453D, Distributor body gasket 47408D, Distributor gear cover gasket 49419D, Condenser hole cover gasket 359966R1 (48472DA), Magneto mounting gasket 55780DE (55780DD). Replaces: 359966R1, 47408D, 47453D, 48472DA, 49419D, 55780DD, 55780DE, E4226. For tractor models A, AV, B, BN, C, H, HV, I4, I6, I9, M, MTA, MV, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, T4, T5, T6, T9, U2, U2A, U4, U6, U9, W4, W6, W6TA, W9, WR9, WR9S, 100, 130, 200, 230, 300, 350, 400, 450, 600, 650, 400, 450 (Item #: 111272, Ref: MGK103) $9.00
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.00
Rotor - Used with Delco distributors 1111411 with a clip held cap. For tractor models: A, I4, AV, Super A, Super AV, Super AV1, B, BN, C, Super C, H, HV, Super H, Super HV, M, Super M, MTA, Super MTA, MV, Super MV, O4, O6, OS4, OS6, T6, W4, W6, 354 (distributors with a tach drive). Replaces 3069778R1. (Item #: 110177, Ref: 1750498M1) $3.60
Spark Plug Wire Set, Custom - IH or Delco Distributors and Magnetos. For the following models with 90 degree angle boots: A, I4, AV, Super A, Super A1, Super AV, SuperAV1, B, BN, C, Super C, Cub, Cub Lo-Boy, 154, 184, 185, H, HV, Super H, Super HV, M, MD, Super M, Super MD, Super MDV, MDV, Super MDVTA, MTA, Super MTA, MV, Super MV, Super MVTA, O4, O6, ODS6, OS4, OS6, T340, T5, T6, TD6, SuperW4, W4, Super W6, Super W6TA, W6, W6TA, Super WD6, WD6, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404, 424, 444, 450, W450, 504. Replaces the following OEMS: 352947R91, 352951R91, 352954R91, 352956R91, 356687R92, 356689R92, 356691R91, 356694R92, 356695R92, 356697R93, 362439R91, 362789R91, 407487R1, 45327DA, 46277DA, 50075D, 52794D, 65352D, 65357D, 65358D, and 65359D. (Item #: 120100, Ref: S.67475) $16.00
Starter, 6 Volt, 3 Bolt Mount - 3-Bolt mounted for Super H, HV, O4, OS4, I4, W4, Super M, MTA, MV, O6, OS6, I6, W6, W6TA. (Item #: 127035, Ref: 1108012) $213.00
Starter, 6 Volt, 3 Bolt Mount, Rebuilt - 3-Bolt mounted for Super H, HV, O4, OS4, I4, W4, Super M, MTA, MV, O6, OS6, I6, W6, W6TA. REBUILT Starter. 6 Volt. Replaces Delco 1108012. Replaces 357907R91, 4406, 140-050, 91-01-3979 Refundable $80 core charge. (Item #: 203213, Ref: 1108012-R) $353.24
Starter Armature - Used with Delco Starter # 736C, 737B, 737G, 1107067, 1107074, 1107093, 1107169, 1107174, 1107404, 1107407, 1107408, 1107427, 1107430, 1107435, 1107444, 1107448, 1107462, 1107487, 1107490, 1107926, 1107999, 1108012, 1108016, 1108038, 1108041, 1108060, 1108080, 1108092, 1108097, 1108103, 1108112, 1108142, 1108158, 1108173, 1108174. Body OD: 2.921 inches, Communicator end OD: 0.563 inches, Drive End OD: 0.563 inches, Length: 12.728 inches, Communicating End to Bearing/Bushing Stop: 0.823 inches, Drive End to Bearing/Bushing Stop: 7.236 inches, Number of Comm. Bars: 23, Lam Stack Thickness: 2.685 inches, Set Screw and Keyway on Drive End. Replaces 1871662, 1878077, 1910938, 1B7705, 813555, 816163, 818002, D4100. (Item #: 182636, Ref: 1871662) $93.58
Starter - Delco Style (4132), Remanufactured, Delco Remy, 1107427, 104219A2 - For International / Farmall tractor models H (s/n 19233-earlier), HV, I4, M (s/n 28174-earlier), MTA, O4, O6, O9, OS4, OS6, Super H, Super W4, Super W6, Super W9, W4, Replaces International OEM number 104219A2, 997870R91, 104219A2R, Replaces Delco Remy manufacturer number 1107427, 1107448, Replaces manufacturer number 4132, 140-013, 91-01-3639, Delco Style, Voltage: 12, Rotation: Counter Clockwise, Teeth: 10, For 6 Volt use Item #: 203150, Additional Handling and Oversize Fees Apply To This Item, (Item #: 210141) $334.01
No Picture Starter - Delco Style (4646), Remanufactured, 61061DA, Delco Remy, 1108913 - For International / Farmall tractor models I6, I9, MD, MTA, OS6, Super W6, Super W9, Replaces Case OEM number 61061DA, Replaces Delco Remy manufacturer number 1108913, Replaces manufacturer number 4646, 140-0961, 91-01-3978, Delco Style, Voltage: 12, Rotation: Counter Clockwise, Teeth: 12, (Item #: 205608) $480.01
No Picture Starter - Delco Style DD (4132), Remanufactured, Delco Remy, 1107427, 104219A2 - For International / Farmall tractor models H (s/n 19233-earlier), HV, I4, M (s/n 28174-earlier), MTA, O4, O6, O9, OS4, OS6, Super H, Super W4, Super W6, Super W9, W4, Replaces International OEM number 104219A2, 997870R91, 104219A2R, Replaces Delco Remy manufacturer number 1107427, 1107448, Replaces manufacturer number 4132, 140-013, 91-01-3639, Delco Style: Direct Drive, Voltage: 6, Rotation: Counter Clockwise, Teeth: 10, For a New version of this sku use Item #: 109769, (Item #: 203150) $353.37
Starter Drive Housing - This Starter Nose Cone is used on Delco starter numbers 1107021, 1107060, 1107067, 1107093, 1107174, 1107427, 1107448, 1108096. Bushing is included. This part replaces Delco part numbers 1878661, 1887109, 1910093, 1943759 (Item #: 179382, Ref: 1878661) $75.01
Starter Nose Cone - This cast nose cone is used with starters that have saddle mount solenoids. Solenoid mount is not cast into this part. Bushing Included. Multi drilled and tapped for multiple applications. Used on Delco: 1107169, 1107358, 1107402, 1107407, 1107413, 1107414, 1107424, 1107434, 1107437, 1107439, 1107440, 1107443, 1107456, 1107458, 1107459, 1107542, 1107663, 1107682, 1107806, 1107813, 1107831, 1107958, 1107967, 1107976, 1108006, 1108009, 1108012, 1108038, 1108041, 1108060, 1108090, 1108621, 1108092, 1108103, 1108130, 1108142, 1108159, 1108165, 1109380, 1813397. Replaces Delco part numbers: 1813396, 1872960, 1874785, 1879052, 1914976, 1924299, 1924468, 1930639, 1935587, 1938304, 1959334, 1959773, 1963665 (Item #: 189672) $64.00
Voltage Regulator, 6 Volt, Positive Ground - REPLACES 121578C1, Delco 1118308, 1118780 and 1119575. Fits tractor models: 100, 130, 140, 200, 330, 340, Cub, Cub Lo-Boy, Super A, Super C, H, M, MTA. This external voltage regulator has a flat base for mounting. There are 4 terminals (lights, battery, field and generator). Designed for A type circuits in positive ground systems with 2 brush generators Measures 7 to 9 output amps. (Item #: 105516, Ref: GDR6003) $30.00
Wiring Harness - Wiring Harness, Headlights. For H, HV, M, MD, MDV, MTA, MV, Super M (Item #: 173035, Ref: 52973DA) $15.20
No Picture Wiring Harness - Lighting - WIRE HARNESS - Headlights only for 200, 230, HV, MTA, Super H, Super M. 6 or 12 volt systems. (Item #: 179266, Ref: 358916R91) $34.05
Wiring Harness, Main - Main cable with battery ignition for gas tractors: M, MV (serial number FBK229911 and above), Super M, MTA (serial number F501 to F28174 and L-500001 to L-504801). Cloth covered harness is manufactured to restoration standards. (Item #: 172840, Ref: 354296R91) $38.20

Engine Bearings
Cam Bearing Set - 3 bearings. For tractor models 400, (450 with C281 engine), M, MTA, MV, O6, OS6, Super M, Super W6, W400, (W450 with C281 engine), W6, W6TA. (Item #: 106662, Ref: CBS248) $47.10
Rod Bearing, STD - Single - Sold individually. For tractor models 400, (450 with C281 engine), (M, MV serial number 278050 and up), MTA, (O6, OS6 serial number 35464 and up), Super M, Super W6, W400, (W450 with C281 engine), (W6 serial number 35464 and up), W6TA. (Item #: 106476, Ref: 356957R11) $15.50

Engine Gaskets
Crank Seal, Rear, Gas - Rear crankshaft seal for gas engines. Requires 2 per engine. For tractor models 400, 450, M, MTA, MV, O6, OS6, Super M, Super W6, W400, W450, W6, W6TA. All with 248, 264, or 281 CID gas engines. (Item #: 106654, Ref: 57613DA) $7.30
Head Gasket - For tractor models (400, W400 serial number 163807 and below), M, MTA, MV, O6, OS6, Super M, Super W6, W6, W6TA. (Item #: 172660, Ref: 369957R1) $59.00
Rear Crankshaft Seal Kit - Fits tractor models I6, M, MTA, MV, O6, OS6, Super M, Super MV, Super W6, Super W6TA, T6, T6-61, U6, W6, 400, 450 (Gas or LP), Wheatland: 400, 450 (Gas or LP); Replaces: Contains two: 57613DA, (subs for 46134D): 46134DA, (sub for 46131DA): 46131DB, Contains two (sub for 46121D): 46121DA, Contains two (sub for 379617R91, 379618R91 and 842578R91): 25093DA (Item #: 178604, Ref: IHS2641) $40.30
Upper Gasket Set - For tractor models with the C264 and C281 engines 400, 450, W450, M, MTA, MV, O6, OS6, Super M, Super W6, W400, W6, W6TA.HGS248 (Item #: 106680, Ref: VGK7510S) $65.00
Valve Cover Gasket - Used on M, Super M, 400, 450 and other equipment with International Gas Engines C248, C264, C281. Replace original part number 45952DB, 45952DC, 45952DA 68040D, 842578R95. (Item #: 128603, Ref: 45952DB) $13.60

Engine Rebuild Kits
Valve Overhaul Kit - Fits M, MV, O6, OS6, W6, Super M, MTA, Super W6, W6-TA (Gas 4 cylinder C248, C264). Kit includes valves, valve springs, valve keys, valve guides. Valve length 5.875 inch. (Item #: 184517, Ref: VOKH264) $320.00

Engine Parts
Cylinder Head Stud - 1/2 inch x 7 1/16 inch. For gas and LP Models: I6, M, MTA, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6, U6, W6, 400, 450. (Item #: 178330, Ref: 49023DA) $17.60
Cylinder Head Stud - 1/2 inch x 6 7/8 inch. For gas and LP Models: I6, M, MTA, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6, U6, W6, 400, 450. (Item #: 178329, Ref: 46117D) $10.98
Governor Spring - This Internal Governor Spring is 2.700 inches overall length with 0.110 inch wire diameter. It fits H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super MV, T6, T9, W4 Through 9 Series, W6, W6TA, W9, WR9, WR9S, 300, 350, 400, 450, 600, 650, Wheatland: 400, 450. It replaces original part numbers 357012R1 and 49407DBX. (Item #: 179313, Ref: 49407DBX) $10.80
Valve Guide - Used in gas cylinder heads with the following casting numbers: 8060, 8060D, 8060DB, 8060DC, 8060DD, 8574, 8574D, 8574DB, 8574DC, 8574DD, 362174R1, 362174R2, 362433R1, 362433R2, 362920R1, 362902R2. These heads are used on C248, C264, and C281 engines. These engines were used one Farmall / International models: M, Super M, MTA, Super MTA, MV, Super MV, O6, OS6, T6, Super W6, W6, W6TA, 400, W400, 450, W450 (Item #: 189897, Ref: 8044DR) $5.50

Engine Pistons and Sleeves
Piston Sleeve - Overbore from 4 inch to 4-1/8 inch. For Gas tractor models 400, 450, MTA, Super M, Super W6, W400, W450, W6TA. (Item #: 128735, Ref: SD152) $67.00

Fuel System / Air Intake
Air Cleaner Bowl - Clear plastic pre-cleaner bowl for the air intake system. Bowl outside diameter at top approximately 7-1/4 inch, side height 3 inches, cone inside diameter at top 3-1/2 inch, overall height 4-1/8 inch. Commonly used on pipe inlets ranging from 2-3 inches. For tractors: M, MD, WR9S, Super WD9, 400, 450, W400, W450, 460, 504, 544 diesel, 455 diesel, 2544 diesel, 5606, Gas powered combines: 403 and 453 Hillside, 503, 615, 715. Can replace Donaldson P02-0227, also replaces 101965A, 10P871, 1125804, 1508881M1, 3119347, 365413R1, 71125804, 73186, 73533, 80073533, C0NN9A663A, F3446R, L60631, R28794 (Item #: 157279, Ref: R28794) $8.20
Air Cleaner Pipe - 2-1/4 inch outside diameter. For tractor models M, MV, Super M, Super MV, MTA, Super MV-TA, (Super W6 serial number 3951 and up), Super W6-TA, 400, 450, W400, W450 all gas or LP. Replaces 51441D. (Item #: 126383, Ref: 357028R1) $38.51
Carburetor Fuel Line Fitting With Strainer - Fits INTERNATIONAL carburetors: 356948R92, 35865R91, 366066R91, 367258R92, 367259R92, 372723R92, 378196R94, 379813R91, 380956R91, 381984R91, 388297R92, 388424R92, 388425R96, 390082R92, 396197R93, 45108DB, 45108DC, 50981DA, 50981DB, 50983DB, 52714D, 52814DA, 52815D, 52815DA, 533622R91, 53873DF, 53873DH, 539575R91, 56543DE, 60329DA. 1/4 inch pipe to 5/16 inch flare. (Item #: 111514, Ref: 29902DX) $16.20
Carburetor Kit, Basic - For M, MV, 6 Dist. with OEM number 47387DB, or with OEM number 50983DB. For Super M, MTA with OEM number 356948R92. For W9, WR9 with OEM number 52814D, 52815D and 60329DA. For 300, 350, 400, 450 all with OEM number 361525R92, 361525R91.: For Super H with OEM# 358065R91 (Item #: 120899, Ref: BK12V) $25.50
Carburetor Kit, Comprehensive - International number 356948R92, 357231R92, 358065R91, 358554R91, 47387DB with 8557DX body, 50983DB with 8557DX body, 52814D, 52815D, 60329DA. Includes gaskets, needle, seat, and throttle shaft. (Item #: 112361, Ref: IHCK09) $31.40
Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: 356948R91. For the following tractor models: M, MTA, 600, W9. Add $125.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203308, Ref: 1414-CARB) $265.01
Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: 47387DB, 47387DC, 50983DB. For the following tractor models: HM, MTA, 600, W9. Add $125.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203308, Ref: 1415-CARB) $265.01
Fuel Cap, Top Vented - 2-11/16 inch inside diameter, 1.500 inch height (including splash guard) and 1.118 inch height cap only. Says "Buy Clean Fuel Keep it Clean". For tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy (WILL NOT FIT 154, 184, 185), F12, F14, F20, F30, H, HV, I4, I6, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MV, Super W4, Super W6, Super WD9, Super WDR9, T4, T5, T6, T9, TD14, TD14A, TD15, TD18, TD18A, TD20, TD6, TD9. (Item #: 121475, Ref: 12770D) $12.40
Fuel Pipe Coupling Nut - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, F12, F14, H, HV, I4, I6, I9, M, MD, MTA, O4, O6, Super A, Super C, Super H, Super M, Super W4, TD6, TD9, W4, W6, W12, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 444, 450, 460, 504, 560, 600, 606, 650, 656, 660, 686, 706, 756, 806, 826, 856, 2444, 3514, 3616, Compatible with International Combine (s) 303, 403, 503, 615, 715, Replaces International OEM number 29899D, 700155R11, 700153R11, 1/2"-20 Hi-duty tube fitting, 5/16" O.D., (Item #: 112642) $3.47
Lift All Control Rod Spring/ Flat Hold Down Spring - For International / Farmall tractor models H, HV, M, MD, MTA, Super H, Super M, Super MTA, Replaces International OEM number 15137E, (Item #: 126555) $16.90
Nut - Repair Keyway Throttle Stop Bolt - For International / Farmall tractor models H, HV, M, MD, MTA, Super H, Super M, Replaces International OEM number 86509309, For square tooth throttle assembly / governor control handle, (Item #: 111049) $0.80
Precleaner Assembly - Complete, glass dust bowl assembly, 2-1/4 inch inside diameter base, just like the original. For tractor models M, MD, Super M, MTA, W6, WD6, I6, O6, ID6, OS6, ODS6, Super WD6, 400, W400, 450, W450. (Item #: 112510, Ref: 59096D) $73.00
Precleaner Bowl - Glass bowl for pre-cleaner assembly 59095D, 59096D. (Just like the original). Tractors: H, Super H, HV, I4, O4, OS4, W4, Super W4, 300, 350, M, MD, Super M, MTA, W6, WD6, I6, O6, ID6, OS6, ODS6, Super WD6, 400, W400, 450, W450. (Item #: 111710, Ref: 54082D) $6.60
Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. (Item #: 105364, Ref: 49923D) $3.50
Throttle Dog - This Throttle Dog is used with square tooth throttle assembly/ governor control handle. Replaces 361245R1 (Item #: 110950, Ref: 361245R1) $7.20
Throttle / Governor Control Spring - This Throttle Lever Spring Fits: H, HV, M, MTA, MV, Super H, Super HV, Super M, Super MV. Measures 1.322 inch overall length, 0.925 Inch Outside Diameter. This is used one stamped steel throttle lever assemblies, not cast iron ones. Replaces: 51349D (Item #: 179413, Ref: 51349D) $6.70
Throttle Plate Assembly - This is a Square Tooth Throttle Control Assembly (Governor Control Assembly) used on H, HV, M, MTA, MV, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA. Replaces: Handle: 361244R11, Sector: 361246R11, Assembly: 366727R91 (Item #: 114409, Ref: 366727R91) $74.00
Throttle Plate Assembly - H, HV, M, MTA, MV, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA; Replaces: Saw tooth Lever: 51348DAX, Saw tooth sector: 51351DBX, 51351DBXA (Item #: 114409, Ref: 51351DBX) $74.00

Gaskets
Push Rod Side Cover Gasket - Replacing OEM part numbers 49029DA, 49029DB this gasket is used on Gas and LP models: M, I6, Super MVTA, MTA, MV6, OS6, Super M, Super MTA, Super MV, Super W6, Super W6TA, W6, 400, 450 (Item #: 154785, Ref: 49029DA) $15.30

Gauges
Amp gauge - Gauge, ammeter has 20-0-20 range. Not Exactly like original. IH Logo. Fits 2 inch diameter hole, stainless steel bezel, black background, white letters and white pinter for tractors: Cub, A, B, Super A, A1, AV, AV1, C, Super C, H, HV, Super H, HV, M, MV, MDV, MD, Super M, MTA, O-4, OS-4, O-6, OS-6, W4, W6, WD-6, W-9, WR-9, WDR-9. Replaces 725-3023, 925-3141, IHS418. (Item #: 102133, Ref: 354473R91) $20.70
Amp Gauge, Original Style - Gauge, ammeter has 20-0-20 range. Original Style. IH Logo. Fits 2 inch diameter hole, stainless steel bezel, black background, white letters and white pinter for tractors: Cub, A, B, Super A, A1, AV, AV1, C, Super C, H, HV, Super H, HV, M, MV, MDV, MD, Super M, MTA, O-4, OS-4, O-6, OS-6, W4, W6, WD-6, W-9, WR-9, WDR-9. Replaces 725-3023, 925-3141, IHS418, 354473R91 (Item #: 121652, Ref: 354473R91OE) $29.74

Hitch / Drawbar
3 Point Conversion Kit - For M, MTA, Super M, Super MTA, MD, 400, 450, 460, 504, and 560 also for 544 and 656 with spacer #861188. Two hydraulic cylinders included. (Order optional bracket #861190 to use swinging drawbar) Cat. I/II Weight is 260Lbs. Note: HK-11062 is similar to the picture shown but has two cylinder locations. (Item #: 111430, Ref: HK11062) $956.00
Drawbar Pin Retainer Plate - Used on the following Farmall / International models: H, M, 560, 806, 1066, MD, MTA, W6TA, W9, O4, WD9, WR9, Super WDR9, OS4, Super H, Super M, Super MD, Super MTA, Hydro 84, Super W4, Super W6, Super W6TA, Super WD6, Super WD9, W4, W6, WD6, WDR9, WR9S, 300, 330, 340, 350, 400, 450, 454, 460, 464, 504, 544, 574, 600, 606, 650, 656, 660, 664, 666, 674, 706, 756, 766, 826, 284, 856, 966, 1026, 385, 484, 584, 684, 686, 784, 884, Super MDTA, Super WD6TA, Super WR9S, Super W9, WD6TA, this part measures 1.480 inches long, 1 inch wide and has a 0.377 inch hole diameter and 0.193 inch thick. Many of the listed models used a round plate rather than the rectangular one. This part will replace the round version. Replaces OEM numbers 132794H1, 491390, 49139D, 57654D, 57655D, 58657D (Item #: 112643, Ref: 49139D) $7.50
Swinging Drawbar Roller Shaft Support - For International / Farmall tractor models H, HV, M, MD, MTA, Super H, Super HV, Super M, Super MTA, Replaces International OEM number 356653R91, (Item #: 126738) $63.00
Three Point Hitch - This 3-point hitch kit fits Rowcrops and Utilities without fast hitch. It also allows use of original draw bar. Kit includes (Cat # 1 on tractor end and Cat # 2 on equipment end, and 2 hydraulic 2 way cylinders, but does not include hoses. Please note, this hitch exceeds size limitations for UPS. This hitch kit must ship via LTL freight truck. (Item #: 1000051, Ref: IHS3009) $1799.99

Hydraulic System
Hydraulic Auxiliary Control Valve Rod - Hydraulic Auxiliary Control Valve Control Rod is 43-1/2 inches long with a 3/8 inch diameter. It fits the following tractors with optional live hydraulics and auxiliary control valve: M, MD, MDV, MTA, MV, Super M, Super MD, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super MTA. It replaces original part number 359479R91 (Item #: 179699, Ref: 359479R91) $41.30
Hydraulic Pump Control Rod - Hydraulic Pump Control Rod is 22-1/4 inches long with a 3/8 inch diameter. One end is 3/8 inch -16 UNC threads. It is used on the following tractors with live hydraulic pump and reservoir mounted under the fuel tank: MTA, Super M, Super MD, Super MDTA, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA. It replaces original part number 358458R11. (Item #: 179701, Ref: 358458R11) $44.50

Lights
Headlight Assembly, Flat Back, 12 Volt - For Farmall Cub, Cub Lo-Boy, C, Super C After 159455, M, MV, MD, MDV, MTA, Super MD, Super MDV. Also for Model 100, 130, 140, 200, 230, 240, 300, 350 Utility, 330, 340, 400, 450. Replaces OEM# 357884R94. Flat-Back (not teardrop) Primered red. Price is for one complete headlamp assembly. (Item #: 105334, Ref: 357884R91-12V) $45.90
Headlight Assembly, Flat Back - 6 Volt - For Farmall Cub, Cub Lo-Boy, C, Super C after serial number 159455, M, MV, MD, MDV, MTA, Super MD, Super MDV, also for Model 100, 130, 140, 200, 230, 240, 300, 350 Utility, 330, 340, 400, 450. Replaces OEM number 357884R94. Flat-Back (not teardrop). Primered red. Price is for one complete headlamp assembly. (Item #: 105333, Ref: 357884R91-6V) $40.50
Headlight Reflector - Item is interchangeable with your original and measures 4-1/2 inch measure directly across the top of the housing. For the following tractors: Cub up to serial number 165152, Super C up to serial number 159454, TD with bulb style light, (Super WDR9, WD9 up to serial number 1041), W6 up to serial number 3950, (Super H, Super HV up to serial number 19233), ( Super AV, Super A, W4 all early up to 1953), (Super M, Super MD up to serial number F28174 and Louisville built up to serial number L504508), A, B, C, H, M, I4, I6, I9, ID6, ID9, AV, BN, MDV, MTA, MV, TD6, W9, O4, WR9, O6, ODS6, OS4, OS6, Super MD, Super MTS, Super W4, WD6, WR9S. Replaces 53523D, AA3238R. (Item #: 112482, Ref: AA3238R) $12.00
Headlight Trim Ring - Moulding trim ring for 5 inch teardrop headlights or rear lights on tractors (painted). For tractor models 100, 130, 140, 200, 230, 240, 300, 340, 350, 400, 450, 600, 650, A, AV, B, C, Cub, Cub Lo-Boy, H, HV, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super C, Super H, Super HV, Super M, Super MD, Super MTA, Super WD9, Super A, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S. (Item #: 112980, Ref: 53525DA) $17.20

Oil System
Oil Filter - Oil filter element, cartridge type with gasket. For gas engines: C113, C152, C248, C264, C281, Element is 3 7/16 inches in diameter and 7 1/2 inch overall length. Replaces: 355010R91, 360431R91, 376375R91, 63858D (Item #: 111121, Ref: 376375R91) $21.00
Oil Filter, Spin-On - For tractors that have been converted from cartridge type to spin on oil filters. (Item #: 118399, Ref: E7NN6714AA) $14.20
Oil Level Indicator - This oil level indicator is a replacement for the oil level petcock. Remove the original petcock and replace with this conversion. Has 3/8 inch NPT male fitting. Dipstick is 4.91 inches long. For models using the original oil petcock in A, AV, B, BN, C, F12, F14, F20, F30, H, HV, I12, I14, I4, I6, M, MTA, MV, O12, O14, O4, O6, OS4, Regular, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, W12, W14, W30, W4, W6, 10-20, 15-30, 22-36 and early models of 350, 400, W400, W450 used to replace top oil checking petcock. Originally used as an aftermarket product in the 1940's. (Item #: 1998TA-New) $46.50
Oil Level Petcock - This oil level indicator system uses 2 petcock valves. Used on models A, AV, BN, C, F12, F14, F20, F30, H, HV, M, MTA, MV, Regular, Super A, Super AV, Super C, Super H, Super M, Super MV, 300, 400, Super MTA, Super W4, Super W6 and some other early IH and McCormick Deering models. McCormick Deering: 10-20, 15-30, 22-36. 3/8" pipe thread. Two used per tractor, sold individually. Replaces 1998TA, OGC200 (Item #: 126590, Ref: 1998TA) $16.90
Oil Pan Drain Plug - White Zinc Finish, 7/8 inch - 18 UNF. Fits multiple models. Order EBU6734A if washer is needed. Replaces: 688067C1, 359875R1. (Item #: 126591, Ref: C5NE6730B) $8.10
Oil Pan Drain Plug Washer - This washer is used with C5NE6730B 7/8 inch Oil Drain Plug. (Item #: 140612, Ref: EBU6734A) $1.60
Spin On Oil Filter Adapter Kit - This Spin On Oil Filter Adapter Kit Fits all Gas and LP, IH Combines: 105, 122, 140, 203, 62, 64, 76, 91, 93. Industrials: (I4, I6 Serial Number 4253 and up). Tractors: 300, 350, 400, 450, (A without hydraulics), B, BN, H, HV, (M, MV Serial Number 595394 and up), MTA, O4, (O6, W6 Serial Number 4253 and up), OS4, OS6, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, (T6, U6 Serial Number 5455 and up) ], (T6-61, U164, U4, UC248 Serial number 2327 and up), W4, W400, W450; For Replacement filter, order E7NN6714AA. Replaces: 538829R91 (Item #: 166373, Ref: 538829R91KIT) $123.00

PTO / Driveline
PTO Seal - Measures 1.306 inch inside diameter, 2.220 inch outside diameter. THIS SEAL IS .312 InchES WIDE. VERIFY THE WIDTH OF YOUR OLD SEAL. YOU NEED TO INSTALL 2 OF THESE IF YOUR OLD SEAL IS WIDER. For tractor models Super A, H after serial number 118000, (M, MD, Super M, Super MTA and Super MD after serial number 59957), Late W4, W6, W9, Super W4, Super W6, Super W9, B250, B275, B414; Also fits the following models with transmission driven PTO (not Live PTO): MTA, 300, 330, 350, 354, 364, 384, 400, 424, 434, 444, 450, 454, 544, 600, 650, 2300, 3414, 3514, 3616. Replaces 3065217R91, 358772R91, 358812R91, 50702D, 372394R91, S90957, 708107R91. (Item #: 114730, Ref: 45702D) $9.80
PTO Seal - For tractor models with Live PTO: Super MTA, 300, 330, 340, 350, 400, 450, 460, 504, 560, 606, 660, W400, W450. 1.375 inch inside diameter, 2.378 inch outside diameter, 0.312 inch wide Replaces 360436R91, 364472R91, 364477R91. (Item #: 116834, Ref: 359051R91) $11.30

Seats
Pan Seat 4-Bolt Mount - Pan Seat with silver padded canvas. Center brass drain hole over metal pan seat frame. For: C, Super C, H, HV, M, Super M, MD, MV, MDV, MTA, Super MTA, Cub, Cub Lo-Boy, 200, 230, 240, 300, 330, 340, 3 50, 400, 404, 450, 460, 504, 606, 2404, 2504, 2606. (Item #: 110069, Ref: R0906) $212.00
Pan Seat 4-Bolt Mount - Pan Seat with a red and white vinyl cover measures 22 inches wide and 19 inches long. For C, Super C, Super H, H, HV, M, Super M, MD, MV, MDV, MTA, Super MTA, Cub, Cub Lo-Boy, 200, 230, 240, 300, 330, 340, 350, 400, 404, 450, 460, 504, 606, 2404, 2504, 2606. (Item #: 101244, Ref: 357518R91) $160.00
Pan Seat 4-Bolt Mount - Black vinyl padded cushion with steel pan seat. For C, Super C, H, HV, M, Super M, MD, MV, MDV, MTA, Super MTA, Cub, Cub Lo-Boy, 200, 230, 240, 300, 330, 340, 350, 400, 404, 450, 460, 504, 606, 2404, 2504, 2606. (Item #: 101245, Ref: R0903) $213.00
Seat Hinge Pin - Pin, hinge for tilt back seat bracket. Pin is 7 inches long and 3/8 inch diameter. Tractors: C, Super C, H and HV, Super H and HV~ M and MD, Super M and MTA~ Super W6 and W6TA~ 200, 230, 300, 340, 350, 400, 450, 560, 660. For 200, 230, 300, 340, 350, 400, 450, 460, 560, 660, C, H, HV, M, MD, MTA, Super C, Super H, Super HV, Super M, Super MD, Super W6, W6TA. OTHER PARTS IN PICTURE SHOWN FOR REFERENCE ONLY. Replaces: Washer: 228280, Pin: 356892R2, Clip: 356893R2 (Item #: 179249, Ref: 356892R2) $12.00
Seat Shock Bushing - This bushing is for the horizontal bolt hole. It measures 1.223 inches outside diameter at the largest point. The hole inside diameter is 0.597 inches. The length measures 0.724 inches overall. 2 to 4 used per shock. This part replaces 72696R1, 70222488, T19118, 230288, 250416R1, F3296R, R26832, 760674M1 (Item #: 109602, Ref: 72696R1) $2.30
Seat Spring - Cone Shape SPRING Measures 13 inches tall and 8.5 inches at base. For tractor models 200, 230, 300, 350, 400, 450, 460, 560, 600, 650, 660, C, H, HV, M, MD, MTA, Super C, Super H, Super M, Super MTA. Replaces IHS030. (Item #: 101283, Ref: 354670R2) $26.90
Seat Support Pivot Rod - Rod that fits in the end of the Seat Support. OTHER PARTS IN PICTURE SHOWN FOR REFERENCE ONLY. (Item #: 105344, Ref: 352648R1) $22.30

Sheet Metal / Body Parts
No Picture Grille Screen - For International / Farmall tractor models A, B, C, Cub (s/n 222500-earlier with round hood / grille), Cub Lo-Boy (s/n 17200-earlier with round hood / grille), H, HV, I4, I6, I9, M, MD, MTA, O4, O6, O9, OS4, OS6, Super A, Super C, Super H, Super HV, Super M, Super MTA, W4, W6, W9, 100, 130, 140 (s/n 23300-earlier), 200, 230, 240, 300, 330, 340, 350, 400, 450, 460, 560, 600, 650, 660, Size: 2' x 3' with 5 squares per inch, Wire Grille Screen Clips use Item #: 108001, Additional Handling and Oversize Fees Apply To This Item, (Item #: 112471) $17.98
Toolbox - Light bar mount, includes decals and brackets. For tractor models H, M, MD, MTA, Super H, Super M, Super MD, Super MTA (Item #: 103984, Ref: 999760R91) $121.00

Steering
Axle - Heavy duty main axle assembly includes bushings. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. Additonal $45 shipping due to weight. (Item #: 120010, Ref: 7453) $966.00
Axle Center Tube - For all models listed with factory IH wide front with tie rods behind center tube: H, Hydro 70, M, MD, MTA, Super H, Super M, Super MD, 1026, 1206, 1256, 300, 350, 400, 450, 460, 544, 560, 656, 666, 706, 756, 806, 826, 856 Axle Center Tube with bushings (48841D) is 42 1/2 inches long and 4 1/2 inches in diameter. Replaces: 358976R31, 383926R21, Bushing: 48841D (Item #: 109489, Ref: 358976R31) $450.00
Axle Clamp, Front, Used - For International tractor models H, HV, Hydro 70, Hydro 86, Hydro 100, Hydro 186, M, MD, MTA, 300, 350, 400, 450, 460, 544, 560, 656, 660, 666, 686, 706, 756, 766, 806, 826, 856, 966, 986, 1026, 1066, 1086, 1206, 1256, 2544, 2706, 2806, 2826, 2856, 21026, 21206, 21256, Replaces International OEM nos 350556R1, Front Axle Clamp, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 434540) $31.01
No Picture Axle Extension Tube - Standard duty, 11-5/8". For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 108809, Ref: 3036) $206.98
No Picture Axle Extension Tube - schwartz part (Item #: 110830, Ref: 3037) $198.98
Axle Extension Tube, Heavy Duty - For Schwartz aftermarket front end. 11-5/8 inch vertical shaft tube. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 111582, Ref: 7465) $343.00
Axle Extension Tube, Heavy Duty - For Schwartz aftermarket front end. 9-5/8 inch vertical shaft tube. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 172645, Ref: 7470) $406.00
Axle Pivot Pin Bushing - This Bushing Measures 1.245 inches inside diameter, 1.375 inches outside diameter, 1.486 inches long. Sold individually. This bushing has a superior dimpled brass inner design to retain grease. No need for an external grease hole. Note: Must be honed or reamed to size when installed. Used on the following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle: 1026, 1256, 400, 450, 660, 666, 300, 350, 460, 544, 560, 656, 706, 756, 806, 826, 856, H, Hydro 70, M, MD, MTA, Super H, Super M, Super MD, Super MDTA, Super MTA, W400, W450. Replaces 48841D (Item #: 109669, Ref: 48841D) $13.50
Bolster Pivot Pin - 1 1/4 inch diameter, 8 1/2 inches long. If you need a 1 1/2 inch Diameter Pin, order 379941R1. For tractor models H, Hydro 70, M, MD, MTA, Super H, Super M, 1206, 1256, 400, 450, 460, 544, 560, 656, 666, 686, 706, 756, 806, 826, 856. Replaces 358978R1, 358978R2 (Item #: 109487, Ref: 358978R2) $27.70
Bracket, Belt Driven Power Steering Pump - Bracket bolts to the left side of the engine above the governor. For tractor models M, MV, Super M, Super MV, MTA, 400, 450, W6, Super W6, W6TA, W400, W450. (Item #: 115153, Ref: 20969) $87.00
Front Axle Assembly, Wide, Heavy Duty - For M, Super M, MTA, 400, 450. Includes 6 bolt hubs with 6 inch bolt circle and 4.62 inch pilot diameter hole, bearings and seals are also included. Heavy Duty Front Axle with hubs and mounting parts. Width on wide axles are adjustable from 60 inches to 86 inches. Additional $ 100.00 shipping due to the weight of this item, 320 pounds. (Item #: 119998, Ref: 23209) $3119.01
No Picture Front Saddle Assembly - Fits Schwartz front end ONLY. For tractor models 300, 350, 400, 450, 460, 544, 560, 656, 706, 756, 806, 856, H, M, MTA, Super H, Super M. (Item #: 172611, Ref: 7443) $332.00
No Picture Heavy Duty Front Axle Complete with Hubs - REPLACES: HDUH4000 NOTE: HDUH models include 6 bolt hubs with 6 inch bolt circle and 4.62 inch pilot diameter hole, bearings and seals are also included. Fits on models: 400, 450, M, MTA, Super M. (Item #: 119998, Ref: 23209) $3119.01
No Picture Pivot Pin 4-3/16 - For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 110958, Ref: 1394) $36.20
No Picture Pivot Pin, 6-11/16 - For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super M, Super H. (Item #: 110959, Ref: 1393) $10.98
Power Steering, Pulley - Crankshaft Drive Pulley for Char-Lynn Power Steering. Used on gas and LP models: M, Super M, MTA, MV, Super MV, Super W6, W6, W6TA, 400, W400, 450, W450. Replaces Char-Lynn 5515 (Item #: 109569, Ref: 5515PL) $102.00
Spindle Bushing - Fits 1.667 inch diameter spindles replaces 376099R1. For use with A-71785HD and OEM spindle. (Item #: 102175, Ref: 358958R2) $9.80
Spindle, LH - Fits Tractor Models: 400, 450 with OEM WIDE FRONT, M LATE, MTA, Super M. (Item #: 104341, Ref: 360407R91) $154.98
Spindle-RH - Fits Tractor Models 400, 450 with OEM WIDE FRONT, M LATE, MTA, Super M. (Item #: 104342, Ref: 360408R91) $311.00
No Picture Steering Arm, LH - Left hand for a Schwarts front end. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 109364, Ref: 2130) $92.00
No Picture Steering Arm, RH - Right Hand for a Schwarts front end. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 108808, Ref: 2129) $89.00
Steering Bracket Assembly - For International / Farmall tractor models H, M, MTA, Super H, Super M, 300, 350, 400, 450, 460, 544, 560, 656, 706, 756, 806, 856, Replaces International OEM number 3049, (Item #: 110829) $106.00
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00
Steering Worm Gear, Sector - 32 teeth. For tractor models 400, 450, M, Super M, Super MTA. The style of this gear is full circle. This gear has 32 teeth. It can also replace a 19 tooth sector (1/2 inch moon style). Replaces: 50037DA, 50037DB, 704168R1. (Item #: 124445, Ref: 50037DB) $164.00
Steering Worm Shaft - This Steering Worm Shaft is 46-1/2 inches overall length with 3/4 inch NF thread. This shaft will NOT fit diesels UNLESS customer lengthens the shaft. Fits: (M, MV gas, LP), (MTA, MTAV, Super M, Super MTA, Super MV, Super MVTA gas, LP; up to serial number F52627 or L512541), (400 LP only; with 22 inch tank; serial number 21804 and up without factory power steering), (450 LP only; with 22 inch tank; up to serial number 13135 without factory power steering). Replaces shaft: 50052DB and 50052D. (Item #: 151915, Ref: 50052D) $180.00
Steering Worm Shaft Bearing - This Steering Worm Shaft Bearing has a 0.984 inch inside diameter, a 2.047 inch outside diameter and a 0.590 inch width. Fits B, BM, BN, C, H, HV, M, MD, MDV, MTA, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDV-TA, Super MTA, Super MV, Super MVTA, 200, 230, 400, 450, Super MTA, (424, 444 used as a steering worm shaft bearing; without power steering), 240, 300, 340, 350, 404, 504, 240, 404. Replaces: 1271857C91, 1273146C91, 210041, 43357D, 69696D, 741-0360, 741-3037, 941-3037, ST225, ST225AT, ST225B, ST225BT, ST225Y, ST678. (Item #: 178091, Ref: ST225B) $9.30
Steering Worm Shaft Oil Seal - This Steering Worm Shaft Oil Seal measures 1.000 inch inside diameter, 1.503 inch outside diameter, 0.250 inch wide. Fits B, BN, C, H, HV, M, MD, MDV, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDV-TA, Super MV, Super MVTA, 200, 230, 240, 400, 450, MTA diesel, 300, 340, 350. Replaces: 359042R91, 359257R91, 364468R91, 43800D, 43800DA, 488561R91. (Item #: 122678, Ref: 43800D) $5.50
Thrust Bearing - For tractor models 684, 685, 685XL, 686, 695, 695XL, 706, 756, 766, 782, 784, 786, 806, 826, 856, 86 SERIES with AXLE PIVOT BALL, NOT PIN), 88 SERIES EARLY with AXLE PIVOT BALL, NOT PIN), 884, 885, 885XL, 886, 895, 895XL, 966, 986, H, HV, HYDRO 100, HYDRO 186, HYDRO 3488, HYDRO 70, HYDRO 84, HYDRO 86, M, MTA, Super H, Super HV, Super M. 1.755 inches inside diameter, 2.685 inches outside diameter, 0.694 inches wide. Replaces 185106C1, 185106C91, 357349R91, 361034R91, 369131R91, 387231R91, 405831R91, 527295R91, 844398R91 (Item #: 102174, Ref: 185106C1) $13.10
Thrust Bearing, Axle - Standard duty. Fits Schwartz/Speeco type front ends. For tractor models 300, 350, (354, 364 last serial number models), 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, (B414 last serial number models), H, M, MTA, Super H, Super M. Replaces OEM number 392671M91. Also replaces SCHWARTZ part number 60351. (Item #: 107048, Ref: T163) $21.70
Tie Rod - Long notched With seal and stud nut for Swartz front end. 18 inches long from center of ball joint to end of shaft. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H. (Item #: 111711, Ref: 22513) $37.40
Tie Rod Assembly - Using this tie rod assembly for the models listed will take modification, but it is the only one available for factory original row crop models: H, M, MD, MTA, Super H, Super M, Super MD, Sure MTA, 300, 350, 400, 450. This tie rod assembly tapered ball stud measures 0.675 inch to 0.762 inch at the widest point of the taper shaft, with 5/8-18 thread. The tie rod is adjustable to a maximum of 34-1/4 inches and a minimum of 20-7/8 inches. Fits factory INTERNATIONAL wide front axles only (with tierods behind the center axle.) Will NOT fit Swartz, Norden, Speeco, or other aftermarket wide front axles. To make this assembly work for these applications, the center tube must be shortened about an inch. We do not have instructions for doing this modification. This part can not be returned if you make modifications to the tube. Contains the following items: 359984R93 Tie Rod- Outer, 359986R1 Clamp, 374062R1 Jam Nut, 383917R1 Tube, 384006R92 Tie Rod- Inner. (Item #: 100869, Ref: 223313) $85.00
Tie Rod, DU Axle - Used on Schwartz front ends, this is a sealed (New Style) Tie Rod. It measures 18.750 inches from center of ball joint to end of rod. The rod has a 1 inch diameter. (Item #: 108804, Ref: 22813) $61.00
No Picture Tie Rod, Inner - Inner tie rod with jam nut, seal and stud nut. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 103164, Ref: 22512) $35.40
Tie Rod Tube - Tube only. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 108807, Ref: 1606) $24.98
Tie Rod Tube Kit - For a Swartz front end. Kit includes, 1 tie rod tube, 1 plug, 1 ball stud, 2 1/8 inch cotter pins, 1 dust seal. For tractor models 300, 350, 400, 450, 460, 504, 544, 560, 656, 700, 706, 730, 756, 800, 806, 830, 856, 930, H, M, MTA, Super H, Super M. (Item #: 112262, Ref: 22812) $71.00

Wheels
Rear Wheel Rim Clamp Bolt - For International / Farmall tractor models H, HV, M, MD, MTA, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super W9, W4, W6, W9, WD9, 300, 400 (s/n 5180-earlier), Replaces International OEM number 48985DA, 13491R1, 4.25" x 5/8" NC, Square head 1", Grade 5, Single Dot Square Head, (Item #: 126624) $13.60
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $357.14
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.60
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $16.90
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.30
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $4.80
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.80
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.10
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $29.70
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $35.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.50
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.80
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $4.80
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $13.80
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.30
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.10
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.10
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.40
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $13.80
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $24.80
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.20
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.10
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.10
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.40
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $13.60
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.20
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.00

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.80
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.30
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.80
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.30
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.70
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $18.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.70
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $26.50

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $82.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $138.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $102.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $171.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $169.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $110.21
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.70
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $10.30
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.40

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $13.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.50
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $28.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $58.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $37.40
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $45.20
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $373.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $444.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $444.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.50
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $33.30

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.60
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.70
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.00
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.00