International Harvester / Farmall W9 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Pedal Shaft Seal - This Seal is used as a brake pedal shaft seal, (2 used per tractor) on Farmall / International: W9, WD9, WR9, Super WDR9, Super WD9, WDR9, WR9S, 600, 650, Super W9, Super WR9S. It measures 1.375 inch inside diameter, 2.130 inch outside diameter, and 0.437 inch wide. Replaces 0511073, 1K1590, 1K1590, 224810, 230608, 241779, 340214, 35451D, 357970R91, 357976R91, 380184R91, 43509D, 43509DA, 511073, 527829R91, 60454D, 659124R91, 70224810, 70230608, 70241779, 70241D, 938294R91, 938294R92, AH14076, AL2094T, AL56820, AM253T, AN30648, AN32717, AP24021, K1590, K1590, M86688, N71730N, T22069 (Item #: 128541, Ref: 70241779) $7.70

Clutch
Clutch Disc, Remanufactured, Minneapolis Moline - For International / Farmall tractor models Super W9, W9, 650, Compatible with Minneapolis Moline tractor models UB, Clutch Size: 12", Clutch Hub: 1-3/4", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: Woven, (Item #: 206004) $105.50
No Picture Pressure Plate - This pressure plate is 12 inches, 3 lever and 12 spring. For Models (M, MD, MDV, MV all after serial number FBK294707), Super M prior to serial number 60000, Super MD, Super MTA prior to serial number 60000, W9, Farmall 450. Replace part numbers 360079R and 360079RN. (Item #: 192515, Ref: 357299R95) $365.00

Cooling System
Radiator Cap - Fits Super A, Super C, Super H, M, MD, Super M, MD, 4, Super W4, O6, W6, ODS6, Super W6 and WD6, W9, WD9, Super W9 and WD9. Not for short filler neck. (Item #: 112290, Ref: 67448DD) $5.98
Radiator Cap With Lever - Pressure cap with lever. For C, H, M, MD, O6, ODS6, Super C, Super H, Super M, Super MD, Super W4, Super W6, Super W9, Super WD6, Super WD9, Super A, W4, W6, W9, WD9 (Item #: 110150, Ref: 67448DDWL) $17.00
Thermostat - This 160 degree Long Neck Thermostat. Fits the following tractor models: H, HV, M, MD, MDV, MTA, MV, O4, O6, Super H, Super HV, Super M, Super MD, Super W6, W4, W6, W9, 300, 350 Gas, 400, 450, 560 Diesel, 656 Diesel, 660 Diesel, and 706 Diesel. It does not come with a gasket. Replaces part numbers 313942R91, 313942R92, 315838R91, 317668R91, 37634DA, 261514R92. (Item #: 110010, Ref: R1852) $38.50
Water Temp Gauge - 19 Lead - with IHC Logo For H, M, W-4, W-6, W-9 R3695 (Item #: 102128, Ref: 63783D) $42.50
Water Temp Gauge - 19 Lead - with IH Logo For H, Super H, M, Super M, Super MTA, W-4, Super W4, W-6, Super W6, W-9 (Item #: 111254, Ref: R2742) $37.30

Decals and Emblems
Decal Set - For McCormick W9, 1940-1944. Complete Decal Set. (Item #: MDW9) $44.18
Front Emblem - Front "McCormick" emblem. For W4, W6, WD6, W9, WD9, 1948 and newer. (Item #: 103910, Ref: 43659D) $25.90
Front Emblem - Hood Emblem For W4, W6, WD6, W9, WR9, WD9, O4, OS4, 06, OS6, ODS6, BEFORE 1947. Bright Metal "McCormick Deering" Spelling. (0942R) (Item #: 103909, Ref: 355156R1) $19.70
IH Decal, 1-5/8", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1 5/8", no background, (Item #: 101024) $2.60
IH Decal, 1", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1", no background, (Item #: 101023) $1.70
IH Decal, 3" x 3-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 3" x 3-1/2", No background, (Item #: 101025) $10.20
IH Decal, 4-1/2" x 5" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 4-1/2" x 5", Mylar decal, (Item #: 101095) $5.10
International Decal, 17", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 17" long, Black, Mylar decal, (Item #: 101105) $5.10
International Decal, 8-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 8 1/2" long, Black, Mylar decal, (Item #: 101104) $3.40
International Decal Set,10" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 10", (Item #: 101022) $27.10
International Decal Set, 1 1/4" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-1/4", (Item #: 101018) $2.60
International Decal Set, 1 3/4"x 1 5/8" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-3/4", (Item #: 101019) $3.40
No Picture International Decal Set, 6 1/2"x 7" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo 7", Vinyl Cut, Shaded Outline, (Item #: 101020) $15.30
No Picture International Decal Set, 7 1/4"x 8" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 8", (Item #: 101021) $20.30
International Harvester Decal, 2-3/4" x 3" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, (Item #: 101093) $3.40
International Harvester Decal, 2" x 2-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/2", No background, Mylar decal, (Item #: 101097) $3.40
International Harvester Decal, 2" x 2-1/4", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/4", Mylar decal, (Item #: 101092) $3.40
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", Mylar decal, (Item #: 101096) $5.10
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", No background, Mylar decal, (Item #: 101098) $5.10
International Harvester Decal, 5" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 5" diameter, Shaded outline, Mylar decal, (Item #: 101099) $5.10
International Harvester Decal, 6" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 6" diameter, Shaded outline, Mylar decal, (Item #: 101100) $6.80
International Harvester Decal, 7-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 7 1/2" diameter, Shaded outline, Mylar decal, (Item #: 101101) $8.50
International Harvester Decal, 9", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 9" diameter, Shaded outline, Mylar decal, (Item #: 101102) $10.20
International Hood Decal, 23-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, Size: 23-1/2", Black lettering, (Item #: 101031) $13.60
International McCormick Decal Set, W-9 Standard, Vinyl - For International / Farmall tractor model W9, (Item #: 100931) $110.00
International McCormick Decal Set, WD-9 Standard Diesel, Vinyl - For International / Farmall tractor model W9, (Item #: 100933) $134.00
International W9 Decal Set, McCormick, Mylar - For International / Farmall tractor model W9, (Item #: 101060) $64.00
No Picture International WR9 Decal Set, Mylar - For International / Farmall tractor model W9, For Vinyl Set use Item #: 100934, (Item #: 101063) $68.00
McCormick International Decal, 10" Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 10" long, Black and white, Vinyl decal, (Item #: 101103) $8.50
McCormick International Decal, Hood, White/Black, 7-1/4", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 7-1/4" black and white, Vinyl decal, (Item #: 101026) $6.80

Drive Train
Bearing - Tractors, Implements. Ball bearing, has many applications including water pump bearing on tractors: M, MD, Super M, Super MD, W6, WD6, 06, ODS6, Super W6, Super WD6, W9, WD9, Super WD9, 400, W400, 450, W450. For 400, 450, 5088, 5288, 5488, M, MD, O6, ODS6, Super M, Super MD, Super W6, Super WD6, Super WD9, W400, W450, W6, W9, WD6, WD9. Replaces ST205A (Item #: 178129, Ref: E75GE9) $7.00
Gear Shift Knob - For Cub, Cub Lo-Boy, A, Super A, Super AV, B, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, W4, W6, WD6, Super W6, W9, WD9, Super WD9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 354, 400, 404, 450, 424, 460, 504, 560, 600, 606, 660, and on the hydraulic lever control on the 454 and 574. Gear shift lever knob. Replaces 3121549R1, IHS266. (Item #: 109514, Ref: 53717DA) $5.90

Electrical System
Battery Box Grommet - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, H, I4, I6, I9, M, MD, O4, O6, Super H, Super M, Super MTA, Super W4, W4, W6, W9, 300, 350, 400, 450, Replaces International OEM number 248-1146, 24179D, 52118D, (Item #: 126446) $2.90
Coil, Original, 12 Volt - OEM style coil. For tractor models 100, A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, MD, W4, W6, Super W4, Super W6, Super W6TA, W9, Super W9, Cub, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450. This is an International Harvester OEM style 12 volt distributor coil. This distributor coil has a 2.8 ohm rating between the two primary winding terminals. Requires an external resistor. (Item #: 154651, Ref: 353875R91) $64.00
Coil, Original, 6 Volt - OEM style coil. Measures overall length of 5 3/8 inches, Diameter at widest point of center ridge is 2 1/4 inches. This distributor coil has a 1.4 ohm rating between the two primary winding terminals. For tractor models 100, A, Super A, B, C, Super C, H, Super H, M, Super M, Super MTA, MD, W4, W6, Super W4, Super W6, Super W6TA, W9, Super W9, Cub, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450. (Item #: 154650, Ref: 353874R91) $62.00
Distributor - Original IHC design comes with a 32 tooth drive gear. For tractor models Super W6TA, Super W9, Super WD6, Super WD6-TA, Super WD9, Super WDR9, W4, W400, W450, W6, W9, WD6, WD9, WDR9, WR9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 504, 600, 650, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 3514. R6332. MHSK1 (Item #: 124839, Ref: 107304C91) $114.00
Distributor - New and complete distributor comes with a 32 tooth gear, and is for tractor models: A, AV, B, BN, C, H, HV, M, MV, Super A, Super AV, Super C, Super H, Super M, Super MTA and other IH equipment with International Distributors. Replaces: 107296C91, 107299C91, 107302C91, 107304C91, 353890R91, Distributor Housing Casting Number: 353898R11, 354900R91, 357935R91, 362473R91, 362722R91, 364653R91, 364696R92, 366928R91, 372712R91, 380622R91. Uses IH points (included). (Item #: 124839, Ref: 107304C91) $114.00
Distributor Cap Spring Clip - Fits listed IH models when equipped with IH brand distributor 353898R11. Replaces: 107384C1, 353894R1 (Item #: 178117, Ref: 353894R1) $16.80
Distributor Drive Shaft - Shaft for the Distributor Drive. For Cub, Cub Lo-Boy, A, Super A, Super AV, B, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MD, 06, OS6, W6, WD6, W9, WD9, WR9, WDR9, WR9S, 200, 330, 340, 350, 400, W400, 404, 450, W450, 504. Distributor Shaft, for battery ignition with original IH distributor. (Item #: 110682, Ref: 353934R11) $17.90
Distributor Dust Cover - Used with horizontal IHC distributor 353898R11 or J4 magneto on Models: A, AV, Super A, Super AV1, B, BN, C, Super C, Cub, Cub Lo-Boy, H, HV, Super H, Super HV, M, MV, MD, MDV, Super M, Super MD, Super MTA, W4, W6, W9, WR9, WR9S, WDR9, O4, O6, OS6, ODS6, I4, I6, ID6, I9, ID9, T6, TD6, TD9, 100, 130, 140, 154, 184, 185, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404. Replaces 384831R91. (Item #: 107074, Ref: 353900R11) $16.10
Distributor Gear - This Distributor Gear has 32 teeth. It is used on IH Distributor 353898R11. Replaces original part numbers 353902R1, 531461R91 (Item #: 111179, Ref: 353902R1) $31.40
Distributor Hold Down Clamp - For 5/16 inch hold down bolt and IH built distributor. 2 used per engine, sold individually. Fits fits tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, H, HV, Hydro 70, Hydro 86, I4, I6, I9, ID6, ID9, M, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, W4, W6, W9, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 2505B, 2510B, 2514B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 574, 600, 606, 650, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856. All with IH distributors. Replaces 341139R1, 353937R1. (Item #: 182464, Ref: 341139R1) $8.90
Distributor, Rebuilt - Complete remanufactured distributor for Farmall Cub, A, B, C, Super A, H, M, Super H, Super M, W6, W9, Super W6, 100, 130, 200, 240, 300, 400, 404, 450, 504 tractors with IH distributor with 353898R1 housing casting number. IH original part numbers 353890R91, 107304C91. A refundable $50.00 core charge will be added to your order. (Item #: 203587, Ref: 353898R1) $235.01
Distributor Terminal Screw - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a zinc plated Terminal Screw. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. Replaces International part number 353907R1 (Item #: 118472, Ref: 353907R1) $7.80
Distributor Terminal Screw Insulator - Used on IH Distributors 353898R1, 368051R1, 401107R1, this is a spring anchor terminal insulator. It will also fit J4 magneto above serial number 139748. It does not fit early J4 Magnetos. (Item #: 118473, Ref: 353906R1) $7.20
Distributor with base and tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, M, Super A, Super C, Super H, Super M, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2424, 2504, With tachometer drive and with base, Includes new distributor cap, points, condenser, 6V coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203589) $350.01
Distributor with base less tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2404, 2424, 2444, 2504, 3444, 3514, Compatible with International Combine (s) 105, 203, Compatible with International Construction and industrial models T6, T340, 500, Without tachometer drive and with base, Includes new distributor cap, points, condenser, 6V Coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203588) $235.01
Electronic Ignition Conversion Kit - 12v Negative Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt NEGATIVE ground system only. Distributors with clip type cap. (Item #: 105071, Ref: 1142) $154.00
Electronic Ignition Conversion Kit - 12v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. 1885368 or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt POSITIVE ground system only. (Item #: 108148, Ref: 1142P12) $177.00
Electronic Ignition Conversion Kit, 6v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with Delco distributor part no. 1885368 with clip type cap. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 6 volt positive ground system only. (Item #: 105072, Ref: 1142P6) $160.00
No Picture Generator - Delco Style (9718), Remanufactured, Delco Remy, 1100501 - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, I9, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, Compatible with International Combine (s) 101, 140, 151, Compatible with International Construction and industrial models T6, Compatible with International Baler (s) 37, 47, 57, Replaces Delco Remy manufacturer number 1100501, Replaces manufacturer number 9718, 340-21, 92-01-3050, Delco Style, Voltage: 6, Rotation: Clockwise, Amperage: 25, Regulator: External, (Item #: 203178) $408.38
Generator Pulley - This 2 piece adjustable pulley is used on gas or LP; with generator #'s 1101355, 1101423, 1100501, 1100997. The pulley measures 4.129 inch Diameter. Made with ductile iron. Includes set screw and lock nut. Used on: H, M, I4, I6, I9, HV, MV, W6TA, W9, O4, WR9, O6, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, W4, W6, WR9S, 300 (Farmall) up to SN 11002, 300 (Industrial) up to SN 2689, 400 (Farmall) up to SN 13458, 600, 650. Replaces 6745D, 6745DA, 6746D, 6746DA (Item #: 125677, Ref: 6745D) $52.80
H4 Magneto Pinion Driven Gear - This gear has 24 teeth and measures: 0.380 inch inside diameter, 0.759 inch outside diameter, 1.075 inch gear outside diameter, 0.952 inch overall height. It is used on H4 Magnetos. (Item #: 183878, Ref: 49420DX) $21.98
Lighting Switch Dimmer Resistor - For International / Farmall tractor models A, B, Cub, H, HV, M, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super W4, Super W6, TD6, TD9, W4, W6, W9, 100, 130, 200, 230, 300, 350, 400, 450, Replaces International OEM number 47889D, Will Not Fit 154, 184, 185, (Item #: 126566) $16.00
Magneto Gasket Set - This magneto gasket set is for H4 Magnetos. It contains; Coil cover gasket 47453D, Distributor body gasket 47408D, Distributor gear cover gasket 49419D, Condenser hole cover gasket 359966R1 (48472DA), Magneto mounting gasket 55780DE (55780DD). Replaces: 359966R1, 47408D, 47453D, 48472DA, 49419D, 55780DD, 55780DE, E4226. For tractor models A, AV, B, BN, C, H, HV, I4, I6, I9, M, MTA, MV, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, T4, T5, T6, T9, U2, U2A, U4, U6, U9, W4, W6, W6TA, W9, WR9, WR9S, 100, 130, 200, 230, 300, 350, 400, 450, 600, 650, 400, 450 (Item #: 111272, Ref: MGK103) $9.00
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.00
Magneto Winding for F4 or H4 - Coil Winding for F4 magneto and H4 magneto; molded, hi-output. 2 inch wide, 3/4 inch hole, 2-3/16 inch outside diameter. Can replace 47439DA. Magneto Winding for F4 and H4 Magnetos used on: F12, F14, F20, F30, H, MD, WD6, W9, WD9. (Note: This will NOT work for E4A magneto). (Item #: 105599, Ref: RW104) $77.00
Push/Pull Switch Knob - For International / Farmall tractor models A, B, C, Cub, H, HV, M, MD, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, W4, W6, W9, Replaces International OEM number 8732D, Knob only replacement for push/pull switches, (Item #: 126614) $8.00
Starter, 6 Volt, 2 Bolt Mount - 2-bolt mounted starter for C163 gas engine on H (to serial number 19233), HV, for 248 gas on M (to serial number 28174), 152 Gas on OS4 (1940 to 1951), C248 Gas on O-6 (1940 to 1951), C264 gas on O-9 (1940 to 1951), C163 Gas on Super W-4 (1952 to 1954), C264 Gas on Super W-6/6TA (1946 to 1951), C335 Gas on Super W-9 (1946 to 1951), C163 Gas on I4 (1940 to 1951). Replaces 1107427, 997870R91, 1107448, 997870R91, 104219A2R. Can be used on a 12 volt system and recommend installing heavy duty starter drive part number 565549-NEW. (Item #: 109769, Ref: 1107448) $140.00
No Picture Starter - Delco Style (4651), Remanufactured, Delco Remy, 1108920 - For International / Farmall tractor models Super W9, W9, Replaces Delco Remy manufacturer number 1108920, 1108943, Replaces manufacturer number 4651, 140-073, Delco Style, Voltage: 6, Rotation: Clockwise, Teeth: 10, (Item #: 205575) $620.01
Starter Drive - For Cub and Lo-Boy 1947-1964, 3230, W9, 390. (Item #: 109966, Ref: 1850844) $37.70
Terminal Clip - Light terminal plate with screws. For 200, 230, 300, 330, 350, 400, 450, 600, 650, A, B, C, H, HV, M, MD, O4, O6, ODS6, OS4, OS6, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super WD9, Super WDR9, Super A, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S (Item #: 117534, Ref: 79407H) $6.50
Wiring Harness Grommet - For International / Farmall tractor models A, B, C, H, HV, I4, I6, I9, M, MD, O4, O6, OS4, OS6, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, Replaces International OEM number 52062D, Mounts in amp box, Outer Diameter: 1.810", Inner Diameter: 1.246", (Item #: 126808) $5.40
No Picture Wiring Harness Kit - For model W9. (Item #: R4150) $246.65

Engine Gaskets
Crank Seal, Front - This front crankshaft oil seal has a 2.625 inch Inside Diameter, a 3.38 inch Outside Diameter and is .475 inch wide. It Fits: I6, I9, ID6, ID9, M, MD, MDV, MV, O6, ODS6, OS6, Super M, Super MD, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, T6, T6-61, T9, TD6, TD6-61, TD9, TD9-91, W400, W450, W6, W9, WR9, WR9S, 400, 450, 600, 650, B-450, BM, BMD, SBMD, Super BM. Replaces: 258511R91, 357972R91, 357977R91, 358511R91, 53872D, 410708 (Item #: 106640, Ref: 357972R1) $13.30
No Picture Pan Gasket - For tractor models W10, W10E, W12, W18, W20, W8, W8E, W9, W9E. (Item #: 106168, Ref: A152479) $26.40

Engine Parts
No Picture Bare Block, Remanufactured, 8318DC - For International / Farmall tractor model W9, Replaces International Casting number 8318DC, Casting number (s): 8318DC, Our remanufactured bare blocks have been; cleaned, inspected, align bored, and pressure checked, (Item #: 204896) $1050.01
No Picture Connecting Rod Bolt Lock Tab - For Diesel models: I9, ID6, MD, MDV, ODS6, Super MD, Super MDV, Super MDV-TA, Super MTA, 400, 450, Super W9, T9, TD6, TD9, W9, WD6, WR9, WR95. GAS and LP: 600, 650. (Item #: 167084, Ref: 253220R1) $6.90
No Picture Cylinder Head, Remanufactured, 8101D - For International / Farmall tractor model W9, Compatible with International Construction and industrial model TD9, Replaces International Casting number 8101D, 8101DN, Engine 350, Diesel, Cylinders 4, Casting No. 8101D, 8101DN, Must ship via freight carrier, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200192) $1175.01
No Picture Cylinder Head, Remanufactured, 8320D - For International / Farmall tractor models Super W9, W9 (Gas), 600, 650, Replaces International Casting number 8320D, Casting No. 8320D, Engines 350, Cylinders: 4, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 205493) $1450.01
No Picture Cylinder Head, Remanufactured, 9195D - For International / Farmall tractor models Super W9, W9 (Gas), 600, 650, Replaces International Casting number 9195D, Engine 350, Cylinders 4, Casting No. 9195D, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200193) $288.01
Governor Spring - This Internal Governor Spring is 2.700 inches overall length with 0.110 inch wire diameter. It fits H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super MV, T6, T9, W4 Through 9 Series, W6, W6TA, W9, WR9, WR9S, 300, 350, 400, 450, 600, 650, Wheatland: 400, 450. It replaces original part numbers 357012R1 and 49407DBX. (Item #: 179313, Ref: 49407DBX) $10.80
Governor Thrust Bearing - Bearing has a outer diameter of 1.575 inches, width of 0.472 of an inch, and an inner diameter of 0.510 of an inch. The lip has an outside diameter of 0.750 of an inch, the shaft has an diameter of 0.656 of an inch, and has 2 pin holes with an inner diameter measuring 0.186 of an inch. For the following models: H, HV, Super H, Super HV, M (gas), Super M (gas), Super MTA (gas), O4, O6, OS4, OS6, Super W4, W4, Super W6 (gas), Super W6TA (gas), W6 (gas), W9 (gas), WR9S (gas), B-275 (gas), B-276 (gas), 300, 350 (gas), 354 (gas), 400, W400, 444 (gas), 450 (gas), W450 (gas), 600 (gas), 650 (gas). Replaces 48250D, 48250DX, and ST506. (Item #: 183913, Ref: 351910R91) $81.00

Engine Rings
Piston Ring Set - 4.500" Bore - 4 Cylinder - For International / Farmall tractor models I9, O9, W9, Compatible with International Engine (s) C335, Bore: 4.500", Compression Rings per Piston: (3) @ .125", Oil Rings per Piston: (2) @ .250", Top Groove Size: .125", Top Groove Style: Barrel Face Chrome, 2nd Groove Size: .125", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .125", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .250", 4th Groove Style: Chrome Rail / Oil Ring Spacer, 5th Groove Size: .250", 5th Groove Style: Cast Iron Oil, Sold as a complete 4 cylinder set, (Item #: 129072) $384.00

Exhaust System
Manifold - Exhaust Manifold with intake for tractor model W9. Replaces OEM# 8321DX, 8321DBX, 8321DAX. (Item #: 111333, Ref: R0305) $303.00
Manifold Gasket Set - This is a Manifold Gasket Set for gas and LP models: I9, Super W9, T9, U9, W9, WR9, WR9S, 600, 650. Replaces: 31336D, 52755DA, 8321DBX (Item #: 113658, Ref: R0305G) $33.70
Muffler - Vertical muffler for gas tractors, fits engines C335, and C350. Inlet inside diameter 3-1/8 inch, outlet outside diameter 3 inch, length 22 inches, diameter 6 inches, round body type. For tractors W9, WR9, 600, 650. For 600, 650, Super WD9, Super WDR9, W9, WD9, WDR9, WR9. (Item #: 100809, Ref: 264116R92) $72.00
Muffler - For W9 gas, WD9 diesel, T9 gas, TD9 and TD14 diesel. Also for International 600 and 650 with C-350 gas and D-350 diesel engines. Muffler is vertical, inlet inside diameter 3-1/8 inch, outlet outside diameter 3 inch, length is 22 inches. Replaces OEM number 303973R91. (Item #: 100809, Ref: R1646) $72.00

Fuel System / Air Intake
Carburetor Float - Float. For Updraft International Carburetors with throat size 1-1/4 inch or 1-3/8 inch. Dimensions: 2 3/16 inch length x 1 3/16 inch height, outside diameter 3 1/2 inches. For 2606, 2706, 300, 350, 400, 450, 460, 560, 600, 606, 650, 660, 706, M, MV, O6, OS6, Super H, Super HV, Super M, Super MTA, Super W6, Super W6TA, W400, W450, W6, W9, WR9, WR9S. (Item #: 107990, Ref: 47398DX) $18.80
Carburetor Fuel Line Fitting With Strainer - Fits INTERNATIONAL carburetors: 356948R92, 35865R91, 366066R91, 367258R92, 367259R92, 372723R92, 378196R94, 379813R91, 380956R91, 381984R91, 388297R92, 388424R92, 388425R96, 390082R92, 396197R93, 45108DB, 45108DC, 50981DA, 50981DB, 50983DB, 52714D, 52814DA, 52815D, 52815DA, 533622R91, 53873DF, 53873DH, 539575R91, 56543DE, 60329DA. 1/4 inch pipe to 5/16 inch flare. (Item #: 111514, Ref: 29902DX) $16.20
Carburetor Kit, Basic - For M, MV, 6 Dist. with OEM number 47387DB, or with OEM number 50983DB. For Super M, MTA with OEM number 356948R92. For W9, WR9 with OEM number 52814D, 52815D and 60329DA. For 300, 350, 400, 450 all with OEM number 361525R92, 361525R91.: For Super H with OEM# 358065R91 (Item #: 120899, Ref: BK12V) $25.50
Carburetor Kit, Comprehensive - For tractor models W9, WR9 with OEM# 52814D, 52815D and 60329DA. Contains the following parts for a Major Overhaul with instructions. Includes: gaskets, needles, seats, shafts, springs, and mixture screw. (Item #: 182785, Ref: IHCK07) $45.10
Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: 356948R91. For the following tractor models: M, MTA, 600, W9. Add $125.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203308, Ref: 1414-CARB) $265.01
Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: 47387DB, 47387DC, 50983DB. For the following tractor models: HM, MTA, 600, W9. Add $125.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203308, Ref: 1415-CARB) $265.01
Fuel Cap - 1 15/16 inch overall outside diameter fits many: 240, 300, 350, 400, 450, 600, 650, H, HV, M, MD, MDV, O4, O6, ODS6, OS4, OS6, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super W6, Super WD6, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S. (Item #: 116503, Ref: 40756D) $4.98
Fuel Cap, Chrome, Unvented - Fits MOST of the following GAS and Diesel tractors: Cub, Cub Lo-Boy, A, Super A, B, C, Super C, H, Super H, M, Super M, 04, 06, W4, W6, Super W4, Super W6, W9, 100, 130, 140, 4156, 4166, 4168. Cap fits neck inside diameter of 1 7/8 inches using 2 locking tabs. (Item #: 107987, Ref: 23995DC-CHROME) $2.60
Fuel Pump Overhaul Kit - For early models with the diaphram attached onto the shaft with a nut. For tractor models F12, F14, I9, I12, O12, O14, W9, W12, W14. NOT FOR USE WITH METHANOL BLENDED GAS***THIS IS FOR THE ORIGINAL O.E.M. PUMP (PART # 24527D) AND THE EARLY AC PUMP. BOTH FEATURED A HAIR SPRING CHECK VALVE; ALSO THE DIAPHRAM IS ATTACHED TO THE SHAFT WITH A NUT. CAN BE USED FOR THE LATE AC REPLACEMENT PUMP, HOWEVER THE CAGED CHECK VALVE, WHICH IS INCLUDED IN IHS164, MUST BE REUSED; ALSO THE SHAFT MUST BE GROUND TO REMOVE THE OLD DIAPHRAM, AND PEENED OVER AFTER THE NEW DIAPHRAM IS ATTACHED. CONTAINS: DIAPHRAM, MOUNTING GASKETS, FUEL BOWL SCREEN AND GASKET, PIVOT SHAFT, PLUNGER, SPRINGS, RETAINERS, PACKINGS. (Item #: 178664, Ref: IHS854) $92.00
Fuel Pump Overhaul Kit - For late models with the diaphram peened onto the shaft. For tractor models F12, F14, I9, I12, O12, O14, W9, W14. NOT FOR USE WITH METHANOL BLENDED GAS. (Item #: 179096, Ref: IHS164) $134.00
Needle and Seat - International - For International / Farmall tractor models I6, I9, M, O6, O9, TD5, TD6, TD9, W6, W9, 400, 450, 650, (Item #: 149811) $31.98
Sediment Bowl Assembly Glass Bowl - Glass bowl with an outside diameter is 2 1/8 and an overall height of 2 3/8. For the following models using a 2 3/8 inch tall glass bowl: O12, O14, O4, O6, OS4, OS6, T340, T5, T6 (up to serial number 29964), W12, W14, W30, Super W4, W4, W40, Super W6, Super W6TA, W6, Super W9, W9, WR9S, F12, F14, F20, F30, 100, 130, 140, 200, 230, 300, 340, 350, 400, W400, 450, W450, 460, 560, 656, 660, 706, 756, 766, 806, 826, 856. Replaces 51344VA and 357957R1. (Item #: 105365, Ref: S.65504) $6.10
Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. Replaces: 13194D, 25854, 49923D (Item #: 105364, Ref: 49923D) $3.50

Gauges
Amp gauge - Gauge, ammeter has 20-0-20 range. Not Exactly like original. IH Logo. Fits 2 inch diameter hole, stainless steel bezel, black background, white letters and white pinter for tractors: Cub, A, B, Super A, A1, AV, AV1, C, Super C, H, HV, Super H, HV, M, MV, MDV, MD, Super M, MTA, O-4, OS-4, O-6, OS-6, W4, W6, WD-6, W-9, WR-9, WDR-9. Replaces 725-3023, 925-3141, IHS418. (Item #: 102133, Ref: 354473R91) $20.70
Amp Gauge - 20-20 style - with IHC Logo. For A, B, C, H, M, W-4, W-6, W-9 (to 1946). (Item #: 121653, Ref: R4186) $27.00
Amp Gauge, Original Style - Gauge, ammeter has 20-0-20 range. Original Style. IH Logo. Fits 2 inch diameter hole, stainless steel bezel, black background, white letters and white pinter for tractors: Cub, A, B, Super A, A1, AV, AV1, C, Super C, H, HV, Super H, HV, M, MV, MDV, MD, Super M, MTA, O-4, OS-4, O-6, OS-6, W4, W6, WD-6, W-9, WR-9, WDR-9. Replaces 725-3023, 925-3141, IHS418, 354473R91 (Item #: 121652, Ref: 354473R91OE) $29.74
Oil Gauge - Oil pressure gauge, 80 pound, fits 2 inch diameter hole. For 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, W4, 400, W6, W9, A, B, C, H, M, Super C, Super W9, Super A. Replaces 536962R1, 536962R2. (Item #: 110411, Ref: FAD9273A) $14.70
Oil Pressure Gauge - For International / Farmall tractor models H, I4, I6, I9, M, O4, O6, O9, W4, W6, W9, Replaces International OEM number 31041DBH, IHC Logo on Face, Black Face, Includes Mounting Studs, (Item #: 108049) $18.60
Oil Pressure Gauge - For International / Farmall tractor models I6, M, Super M, Super MTA, Super W6, Super W9, TD6, TD9, W6, W9, Replaces International OEM number 258634R91, 702027C1, IH Logo on Face, Dash Mounted, 0-45 PSI, (Item #: 121660) $47.00
Oil Pressure Gauge - Zone Style - with IH Logo with studs - Does not include bracket. For H, Super H, M, Super M, Super MTA, W-4, Super W4, W-6, Super W6, W-9, Super W9 (from 1947). (Item #: 110849, Ref: 41934DB) $45.20

Hitch / Drawbar
Drawbar Pin Retainer Plate - Used on the following Farmall / International models: H, M, 560, 806, 1066, MD, MTA, W6TA, W9, O4, WD9, WR9, Super WDR9, OS4, Super H, Super M, Super MD, Super MTA, Hydro 84, Super W4, Super W6, Super W6TA, Super WD6, Super WD9, W4, W6, WD6, WDR9, WR9S, 300, 330, 340, 350, 400, 450, 454, 460, 464, 504, 544, 574, 600, 606, 650, 656, 660, 664, 666, 674, 706, 756, 766, 826, 284, 856, 966, 1026, 385, 484, 584, 684, 686, 784, 884, Super MDTA, Super WD6TA, Super WR9S, Super W9, WD6TA, this part measures 1.480 inches long, 1 inch wide and has a 0.377 inch hole diameter and 0.193 inch thick. Many of the listed models used a round plate rather than the rectangular one. This part will replace the round version. Replaces OEM numbers 132794H1, 491390, 49139D, 57654D, 57655D, 58657D (Item #: 112643, Ref: 49139D) $7.50

Hydraulic System
Hydraulic Manifold - Hydraulic Pump Flange, Hydraulic Manifold, Port Block is used on (M, Super M, 400, 450 Gas or Diesel), Super W6, Super W9, Super WD6, Super WD9, W6, W9, WD6, WD9, 600, 650. 3/4 inch NPT inlet and outlet. Threaded for hydraulic hose. Must use rubber hose lines. (Item #: 115188, Ref: IHS1240) $71.00

Lights
Headlight Lens - Replacement Glass Lens is 4.75 inch outside diameter for IH (45640DB) Headlight Assemblies. Models: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650, A, B, C, Cub, Cub Lo-Boy, H, M, MD, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super W4, Super W6, W4, W6, W9, WD6, WD9. (Item #: 111330, Ref: GC200) $15.30
Headlight Reflector - Item is interchangeable with your original and measures 4-1/2 inch measure directly across the top of the housing. For the following tractors: Cub up to serial number 165152, Super C up to serial number 159454, TD with bulb style light, (Super WDR9, WD9 up to serial number 1041), W6 up to serial number 3950, (Super H, Super HV up to serial number 19233), ( Super AV, Super A, W4 all early up to 1953), (Super M, Super MD up to serial number F28174 and Louisville built up to serial number L504508), A, B, C, H, M, I4, I6, I9, ID6, ID9, AV, BN, MDV, MTA, MV, TD6, W9, O4, WR9, O6, ODS6, OS4, OS6, Super MD, Super MTS, Super W4, WD6, WR9S. Replaces 53523D, AA3238R. (Item #: 112482, Ref: AA3238R) $12.00
Headlight Trim Ring - Moulding trim ring for 5 inch teardrop headlights or rear lights on tractors (painted). For tractor models 100, 130, 140, 200, 230, 240, 300, 340, 350, 400, 450, 600, 650, A, AV, B, C, Cub, Cub Lo-Boy, H, HV, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super C, Super H, Super HV, Super M, Super MD, Super MTA, Super WD9, Super A, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S. (Item #: 112980, Ref: 53525DA) $17.20
Light Clamp - Clamp, lamp assembly for tractors. For tractor models 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650, A, B, C, Cub, Cub Lo-Boy, H, M, MD, O4, O6, OS4, OS6, Super C, Super H, Super M, Super W6, Super A, W4, W6, W9, WD6, WD9. (Item #: 178025, Ref: 350920R1) $10.00
Light Switch, 12 Volt - 4 position with Old style knob, replaces cut out switch when converted to regulator. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 125672, Ref: R5362) $46.70
Light Switch, 12 Volt - 3 position with Old style knob, with regulator only. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 107984, Ref: R5364) $32.98
Light Switch, 12 Volt - 4 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 178354, Ref: R5366) $61.00
Light Switch, 12 Volt - 3 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 107095, Ref: R5368) $40.70
Light Switch, 6 Volt - 4 position with Old style knob, replaces cut out switch when converted to regulator. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 178387, Ref: R5361) $61.00
Light Switch, 6 Volt - 3 position with Old style knob, with regulator only. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 125715, Ref: R5363) $49.40
Light Switch, 6 Volt - 4 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 178351, Ref: R5365) $29.98
No Picture Light Switch, 6 Volt - 3 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 107094, Ref: R5367) $27.00
Light Switch Knob - Old style for rotary light switches. For tractor models A, AV, B, BN, C, H, HV, M, MD, MV, MDV, W4, W6, W9, WD6, WD9, WR9, WDR9, O4, OS4, I4, I6, I9, ID6, ID9, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MD, Super MV, Super MDV, Super MTA, Super W4, Super W6, Super W6TA, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, Cub. (Item #: 179711, Ref: 57313D) $11.10
Rear Combo Light Assembly -6Volt - Replaces 355911R91, manufactured to restoration standards. Rear combo light assembly, 6 Volt. Includes red jewel light with rotary switch. For: Cub, Super A and AV, C, Super C, H, HV, Super H and HV, M, MD, MDV, MV, Super M and MTA, O4, o6, ODS6, OS6, W6, WD6, W6TA, Super W6, W9, WDR9, WR9, Super W9, 100, 130, 140, 230, 240, 300, 330, 340, 350, 400, 450. (Item #: 105335, Ref: 355914R91-6V) $73.00
No Picture Rotary Light Switch. Early - This 4 position, 6 volt light switch is for models with CUT OUT RELAY, not a voltage regulator. Cut our telays have 2 terminals on one side and 1 terminal on the other. Voltage regulators have 3 terminals on 1 side and 1 terminal on the other. OFF is a position (of the 4). For models A, AV, B, H, M, MV, O4, O6, OS4, OS6, W4, W6, WR9, C, Cub, HV, W9, WD6, WD9. Replaces 57310DX, 57310DY and 1994019. (Item #: 126644, Ref: 47890DX) $135.00

Miscellaneous
Gear Shift Boot - For International / Farmall tractor models I9, W9, 600, 650, Replaces International OEM number 61064D, Shaft 1.395" Hole, Base 2.160" Hole, Height: 4-1/8", (Item #: 126660) $44.00

Oil System
Oil Filter - Oil filter element, cartridge type with gasket. For gas engines: C248, C335, C350, in tractors: M and MV to serial number 59393, I6 and W6 to serial number 4242, W9, 600, 650. For diesel engines D248, D264, D281, D335, D350, tractors: MD, Super MD, ODS6, WD6, Super WD6, For 400, 4252, 450, 6, 600, 650, M, MD, MV, ODS6, Super MD, Super WD6, Super WD9, W6, W9, WD6, WD9. Filter is 3 7/8 inches in diameter and 7 inches overall length. Replaces: 376376R91, 257867R92, 360432R91, 63884D, 63885D. (Item #: 185572, Ref: 376376R91) $22.00
Oil Pan Drain Plug - White Zinc Finish, 7/8 inch - 18 UNF. Fits multiple models. Order EBU6734A if washer is needed. Replaces: 688067C1, 359875R1. (Item #: 126591, Ref: C5NE6730B) $8.10
Oil Pan Drain Plug Washer - This washer is used with C5NE6730B 7/8 inch Oil Drain Plug. (Item #: 140612, Ref: EBU6734A) $1.60
Oil Pressure Gauge - Zone Style - with IHC Logo with Studs For H, M, W-4, W-6, W-9 (To 1946) (Item #: 113566, Ref: R2737) $49.98

PTO / Driveline
PTO Seal - Measures 1.306 inch inside diameter, 2.220 inch outside diameter. THIS SEAL IS .312 InchES WIDE. VERIFY THE WIDTH OF YOUR OLD SEAL. YOU NEED TO INSTALL 2 OF THESE IF YOUR OLD SEAL IS WIDER. For tractor models Super A, H after serial number 118000, (M, MD, Super M, Super MTA and Super MD after serial number 59957), Late W4, W6, W9, Super W4, Super W6, Super W9, B250, B275, B414; Also fits the following models with transmission driven PTO (not Live PTO): MTA, 300, 330, 350, 354, 364, 384, 400, 424, 434, 444, 450, 454, 544, 600, 650, 2300, 3414, 3514, 3616. Replaces 3065217R91, 358772R91, 358812R91, 50702D, 372394R91, S90957, 708107R91. (Item #: 114730, Ref: 45702D) $9.80

Seats
No Picture Seat Custom with Fold Up Arms - Black vinyl assy. with fold up arm rests fits, 1030, 1031, 1032, 1070, 1175, 1190, 1200TK, 1290, 1390, 1470TK, 200, 230, 240, 2504, 300, 330, 340, 350, 400, 404, 450, 460, 480B, 503, 504, 560, 580B, 600, 606, 650, 660, 730, 740, 830, 840, 870, 930, 940. MUST USE ADAPTER FOR FOLLOWING MODELS, A, B, C, H, HV, M, MDV, MD, MV, Super H, Super A, Super M, W9, WD9, WDR9, WR9S. (USE ADAPTER # CSA300). (Item #: 101387, Ref: CS108-1V) $116.00
Seat Pan - Steel Black vinyl without drain hole Fits tractor models, 100, 140, 200, 230, 240, 300, 340, 350, 460 DSL, 600, 650, A, AV, B, C, Cub, Cub Lo-Boy, H, HV, M, MD, MDV, MTD, MV, Super H, Super M, W9, WD9, WDR9, WR9S (Item #: 191059, Ref: 357518R92-1) $205.00
No Picture Seat Pan - Steel Silver vinyl Fits Models, 100, 140, 200, 230, 240, 300, 340, 350, 460 DSL, 600, 650, A, AV, B, C, H, HV, M, MD, MDV, MTD, MV, Super H, Super M, W9, WD9, WDR9, WR9S. (Item #: 101246, Ref: 357518R92-18) $148.00

Sheet Metal / Body Parts
Battery Box - This restoration quality battery box comes with a lid and fits the following tractor models: I6, O6, OS6, Super W6, Super WD9, Super WDR9, W6, W9, WR9, 600 Diesel, and 650 Diesel. Please note that Diesel model tractors require 2. It measures: 7 3/16 inches x 11 3/4 inches inside, and is 9 1/8 inches tall. It replaces the part number 60700D. (Item #: 179384, Ref: 60700DR) $146.44
Battery Hold Down Rubber - The battery hold down rubber is3/4 inches tall, inserts into the retainers in the battery box lid. These are sold EACH. For tractor models Cub, Cub Lo-Boy, A, AV, B, (BN, C 51690D), AI, H, HV, M, MV, MD, MDV, W6, W9, WD6, Super A, Super C, Super H, Super HV, Super M, Super MTA, Super W6, 100, 130, 140, 200, 230, 600, 650. Replaces: 51690D. (Item #: 116587, Ref: R5103) $4.60
Fender Extension Mounting Kit - One kit used per tractor. For tractor models H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDTA, O4, Super W4, W6, WD6, Super W6, Super W6TA, W9, WD9, Super WD9, 100, 130, 140, 400, 230, 240, 300, 330, 340, 350, 400, 450. Fender mounting Kit includes 2 fender flat brackets with (34 Pieces) all mounting hardware. Replaces IHS364. (Item #: 103989, Ref: 8000072) $90.00
No Picture Grille Screen - For International / Farmall tractor models A, B, C, Cub (s/n 222500-earlier with round hood / grille), Cub Lo-Boy (s/n 17200-earlier with round hood / grille), H, HV, I4, I6, I9, M, MD, MTA, O4, O6, O9, OS4, OS6, Super A, Super C, Super H, Super HV, Super M, Super MTA, W4, W6, W9, 100, 130, 140 (s/n 23300-earlier), 200, 230, 240, 300, 330, 340, 350, 400, 450, 460, 560, 600, 650, 660, Size: 2' x 3' with 5 squares per inch, Wire Grille Screen Clips use Item #: 108001, Additional Handling and Oversize Fees Apply To This Item, (Item #: 112471) $17.98

Steering
Steering Wheel - For M, MD, W9, WD9, WR9, 400, 450, 600, 650. Steering Wheel 20 inches in diameter, 3/4 inch keyed hub, 4 spokes. (Item #: 101430, Ref: 557282R91) $43.60
Steering Wheel - 17-5/8 inch diameter, 3/4 inch hub, for keyed shaft. 3 Spoke. Super A serial number 356000 and up, C, Super C, H, Super H, M, Super M, MD, W4, Super W4, W6, Super W6, W9, 100, 130, 200, 230, 240 and 300, 350, 400, 450 without Power Steering. Metal Spokes. Replaces IHS328. (Item #: 101429, Ref: 60070D-OE) $42.00
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00

Wheels
Front Wheel / Rim Clamp - Used on many Farmall / IH tractors, this clamp 1.485 inch over all length with a 0.540 inch hole. Three or more used per wheel. Sold individually. Replaces 48976DA (Item #: 152052, Ref: 48976DA) $13.00
Rear Wheel Rim Clamp Bolt - For International / Farmall tractor models H, HV, M, MD, MTA, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super W9, W4, W6, W9, WD9, 300, 400 (s/n 5180-earlier), Replaces International OEM number 48985DA, 13491R1, 4.25" x 5/8" NC, Square head 1", Grade 5, Single Dot Square Head, (Item #: 126624) $13.60
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $357.14
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.60
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $16.90
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.30
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $4.80
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.80
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.10
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $29.70
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $35.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.50
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.80
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $4.80
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $13.80
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.30
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.10
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.10
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.40
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $13.80
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $24.80
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.20
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.10
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.10
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.40
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $13.60
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.20
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.00

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.80
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.30
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.80
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.30
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.70
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $18.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.70
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $26.50

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $82.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $138.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $102.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $171.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $169.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $110.21
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.70
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $10.30
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.40

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $13.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.50
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $28.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $58.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $37.40
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $45.20
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $373.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $444.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $444.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.50
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $33.30

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.60
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.70
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.00
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.00