FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Ford 3600V Tractor Parts

[Categories] [All Ford Models] [Print]

Clutch

Clutch Alignment Tool - For a Double Clutch. The Large Spline is 1-7/8 inches with 29 Splines. The Small Spline 1 inch with 15 Splines. Pilot Diameter is 0.670 inches. This can also be used for 15 spline single clutches that match pilot and 1 inch by 15 spines. (Item #: 122258, Ref: AG15) $24.80

Clutch Disc, 11 Inch - 15-Spline, 1 inch Hub, Woven Facing. For Tractors including: (2000 and 3000 1965 to 9-1969) Replaces C7NN7550C. Models with 7 and 8 speed transmissions and PTO. Also fits the following models (less PTO): (4100, 4110, 4200 1965 to 9-1969), (4100 10-1971 and up). 83971425, C7NN7550V, E8NN7550BA, C7NN7550B (Item #: 122241, Ref: C7NN7550V) $73.00

Clutch Kit - This single stage clutch kit contains a 11 inch, 10 spline rigid drive clutch disc (87295808), a 11 inch single pressure plate with six bolt mount, (used 1969 and later) (C9NN7563D), a pilot bearing which measures 1.575 inches OD, .669 inch ID, .472 inches wide (C5NN7600A), new release bearing which measures 4.0700 inches outside diameter, 2.4997 inches inside diameter, 0.8700 inches wide (83914247), and clutch alignment tool. **NOTE** Some tractors use a release bearing which measures 2.0625 inches inside diameter, 3.515 inches outside diameter and .840 inches in width. If you need this smaller bearing, also order part number N1087. For tractor models 2110, 2120, 2150, 2300, 230A, 231, 2310, 233, 234, 2600, 2600V, 2610, 2810, 2910, 3000, 3055, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 334, 335, 345C, 345D, 3600, 3600V, 3610, 3900, 4110, 4140, 4190, 4330, 4340, 4400, 4410, 445C, 445D, 4500, 4600, 4600SU, 4610, 5000, 5190, 530A, 5340, 545C, 545D. (Item #: 183011, Ref: D0NN7563A-KIT) $258.00

Clutch Kit, 11 Inch IPTO - Kit contains 11 inch 10 spline four pad ceramic disc. (Note, this replaces a three pad triangular type drive disc) C7NN7550AC, 11 inch 29 spline IPTO hub pressure plate with four finger design that will also replace three finger type with six (6) bolt mounting design D8NN7563DB, release bearing 83914247, pilot bearing C5NN7600A, and 1 inch by 10 spline and 1-7/8 inch by 29 spline pilot tool. (Item #: 192660, Ref: 1112-6113) $338.00

Clutch Kit, 11 Single - This Clutch Kit contains 11 inch 15 spline spring drive disc E8NN7550AA, 11 inch single pressure plate C9NN7563D, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool. Used on some Ford tractors 1965 and later. (Item #: 119878, Ref: FC563ZNKIT) $339.00

Clutch Kit, 13 Inch Single - This Kit contains 13 inch - 10 spline spring drive disc with 1 3/4 inch hub 82011593, 13 inch single pressure plate w/ring D8NN7563AB, pilot bearing F0NNN779AA and release bearing 83914247, includes pilot tool. Replaces 82006046, 82011593, D8NN7563AB (Item #: 112322, Ref: 11126087) $360.00

Clutch Pedal Return Spring - This Clutch Pedal Return Spring is used on multiple Ford/ New Holland Tractors and Industrial Models, build 1965 and later. It replaces original part numbers C7NN7N598A and 81820895 (Item #: 153432, Ref: C7NN7N598A) $5.10

Clutch Plate - Pressure Plate Assembly, 11 inch. 1.875 inch 29 spline center. Replaces D8NN7563DA, C9NN7563F, C7NN7563J. (Item #: 135020, Ref: D8NN7563DB) $186.00

Pressure Plate Assembly - This is an 11 inch Double Clutch with a 29 Spline 8 1/2 inch PTO Disc with 1 7/8 inch hub, and a 1.750 inch Flywheel Step. It replaces part numbers 86634451, D8NN7502AA, D8NN7502BA, D8NNY502AA and 83939291. (Item #: 159119, Ref: D8NN7502BA) $338.00

Release Bearing - This clutch release bearing has an inside diameter of 2.4997 inches, an outside diameter of 4.0700 inches, and is 0.8700 inches wide. This release bearing is used in multiple Ford Tractors. Replaces original part numbers D8NN7580AA, D8NN7580BA, D8NN7580BB, E4NN7580AA, D8NN7580CA, C7NN7580A, 82010859, 83914247, 83933520, 83946908 and 86534551. (Item #: 112189, Ref: N1585) $22.50

Cooling System

Water Pump Gasket - This is the Water Pump to Pump Housing Gaskets used in Ford/New Holland equipment, 1965 and later. It replaces original part numbers 83959398, E6NN8513AA. (Item #: 117438, Ref: E6NN8513AA) $3.80

Drive Train

Countershaft Gear - Replacing Ford / New Holland part numbers 81804753, C5NN7113B, 81869991, this Transmission Countershaft Gear has 16 and 35 teeth. It is used on Ford models 2000, 2100, 2110, 2110LCG, 2120, 2150, 230, 2300, 230A, 231, 2310, 233, 234, 250C, 2600, 2600N, 2600V, 260C, 2610, 2610V, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 333, 3330, 334, 335, 340, 3400, 340A, 340B, 3430, 345C, 345D, 3500, 3550, 3600, 3600N, 3600V, 3610, 3610V, 3900, 3910, 3910N, 3910V, 3930, 3930N, 4000, 4100, 4110, 4110LCG, 4110N, 4110V, 4130, 4130N, 4140, 4190, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 445C, 445D, 4500, 455, 4600, 4600SU, 4610, 4610N, 4610SU, 4610V, 4630, 4630N, 4830, 4830N, 5000, 5030, 5100, 515, 5200, 530, 530A, 531, 532, 5340, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 655, 655A, 7000, 7100, 7200 (Item #: 172893, Ref: C5NN7113B) $383.00

Gear Shift Boot - This Gear Shift Boot can be used on multiple Ford/New Holland Tractors built 1965 and later. The top holes is 5/8 inch and the bottom hole is 2 1/2 inches. It replaces original part numbers C5NN27534, C5NN275394, C5NN7277D, D4NN7N309A, 82007346. (Item #: 164365, Ref: C5NN27534) $3.60

Main Shaft Connecting Coupling - For tractor models 2000, 3000, 8N, NAA, Jubilee and others all with 4 speed transmission. Main shaft connecting coupling has 21 teeth, 16 spline. Replaces 83959995, 957E7106 (Item #: 172715, Ref: E6NN7106AA) $68.00

Mainshaft Front Bearing - Measuring 30mm inside diameter, 72mm outside diameter, and 20.75mm wide, this bearing replaces OEM numbers D0NNN755B, 46805, 26800340. It is used on Ford models 2000, 2100, 2110, 2600, 2600N, 2600V, 2810, 2910, 3000, 3100, 3330, 335, 3400, 3500, 3550, 3600, 3600N, 3600V, 3900, 3910, 3910N, 3910V, 4000, 4100, 4110, 4110N, 4110V, 4140, 420, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4600SU, 4610, 4610N, 4610SU, 4610V, 5000, 5100, 515, 5200, 532, 5340, 535, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7700 (Item #: 182968, Ref: D0NNN755B) $24.90

PTO Input Housing Gasket - Used on many Ford / New Holland tractors, 1965 and later. It replaces OEM part numbers 81804647, 81804648, 83959976, C5NN7N051A, C5NN7N051B, E7NN7N051AA (Item #: 179416, Ref: C5NN7N051B) $1.10

Electrical System

Fuse Holder - Mounts in 5/8 inch diameter hole. 2 spade connectors. Replaces: 22-226, 578489, 7020480, C7NN14411A, H340505, P41894 (Item #: 112273, Ref: 376852R91) $10.90

Ignition Switch, Keyed - This 5 position, 7 terminal ignition switch comes with 2 key. Used on many tractor models (2000, 3000, 4000, 5000, 7000 1965-1975), 8000-9700, TW10, TW20, TW30, all 1968-1982. For 2600-7700 1975-1981. For 230A, 231, 233, 234, 333, 334, 335, 420, 515, 530A, 532, 535, all 1981-1990. For 7810-8210 1982-10/1985. For TW5-TW35 to 5/1983-2/1990. 8530-8830 3/1990 and up. Starter and Heat Ignition Switch for tractors with cold start. Not for Shibaura built tractors. Replaces OEM 82849085, 81871583, 81838692, 83999543, 83902803, E7NN11N501AB, D3NN11N501A, D5NN11N501A, C5NN11N501A, E7NN11N501AC, 83959710, 83976890, E7NN11N501AA, E8NN11N501AA (Item #: 116913, Ref: E7NN11N501AB) $9.80

Engine Gaskets

Oil Pan Gasket - For the following 3 Cylinder Gas or Diesel Engines: 158, 175, 192, 201 CID, used in tractors 1965 and newer: 2000, 2100, 2110, 2110LCG, 2120, 2150, 230, 2300, 230A, 231, 2310, 233, 234, 2600, 2600N, 2600V, 2610, 2610V, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3230, 3300, 3310, 333, 3330, 334, 335, 3400, 340A, 3430, 345C, 345D, 3500, 3550, 3600, 3600N, 3600V, 3610, 3610V, 3900, 3910, 3910N, 3910V, 3930, 3930N, 4000, 4100, 4110, 4110LCG, 4110N, 4110V, 4130, 4130N, 4140, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 445C, 445D, 450, 4500, 455, 455C, 455D, 4600, 4600SU, 4610, 4610N, 4610SU, 4610V, 4630, 4630N, 5000, 5100, 515, 5200, 530A, 531, 532, 5340, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 55A, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7630, 7700. Replacing 83990594, D0NN6710B, 87295239, 81824481, 1824481, F0NN710AA. (Item #: 106335, Ref: F0NN6710AA) $9.20

Rear Seal Gasket - Gasket, Crankshaft Rear Seal Retainer. For 230A, 231, 2310, 233, 234, 250C, 2600, 2600N, 2600V, 2610, 2610V, 2810, 2910, 3000, 3230, 333, 334, 335, 3430, 345C, 345D, 3600, 3600N, 3600V, 3610, 3610V, 3900, 3910, 3910N, 3910V, 3930, 3930N, 4000, 4100, 4110, 4110N, 4110V, 4130, 4130N, 4140, 420, 4200, 4330, 445C, 445D, 4600, 4600SU, 4610, 4610N, 4610SU, 4610V, 4630, 4630N, 4830, 4830N, 5000, 5030, 5110, 515, 530A, 531, 532, 535, 545C, 545D, 550, 555, 555A, 555C, 555D, 5600, 5610, 5700, 575D, 5900, 6410, 655, 655A, 655C, 655D, 6600, 6610, 6700, 6710, 675D, 6810, 7100, 7200, 7410, 755, 755B, 7600, 7610, 7630, 7700, 7710, 7810, 7910, 8000, 8030, 8200, 8210, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9200, 9600, 9700, TW10, TW15, TW20, TW25, TW30, TW35, TW5. Replaces 3959128, 83959128, 83957246, 81813951, E9NN6N305AA, 81864478, 81864478GV, 87554506, E5HN6N305AC, E9NN6N305AB, VPC5311 (Item #: 172805, Ref: E9NN6N305AB) $4.10

Engine Parts

Idler Pulley With Bracket - This Idler Pulley With Bracket is used on multiple Ford / New Holland Agriculture and Industrial models. It replaces part numbers 83986807, E6NN8A614AB (Item #: 160935, Ref: E6NN8A614AB) $117.00

Ring Gear, Flywheel - For gas and diesel. Measures 16.115 outside diameter, 14.52 inside diameter, .625 width and has 128 teeth. For models 2000, 3000, 4000, 5000, 6000, 7000, all 1965-1975. For 2600, 3600, 4600, 5600, 6600, 7700, all 1975-1981. For 5000 gas 6/1971-1975. For 3230, 3430, 3930, 4130, 4430, 4830, 5030, 3/1990 and up. Also used on many industrials and later models. Replaces C5NE6384AA, 83949153, 82954183, 9710967, 500791, 18042303, 80873368, 873368, 3949153. Starter Flywheel Ring Gear. (Item #: 111310, Ref: E2NN6384AA) $39.00

Fuel System / Air Intake

Air Cleaner Bowl - Clear plastic pre-cleaner bowl for the air intake system. Bowl outside diameter at top approximately 7-1/4 inch, side height 3 inches, cone inside diameter at top 3-1/2 inch, overall height 4-1/8 inch. Commonly used on pipe inlets ranging from 2-3 inches. For tractor models 2000, 2310, 2600, 2610, 2810, 2910, 3000, 3600, 3610, 3900, 3910, 4000, 4100, 4110, 4600, 4610, 5000, 531, 5600, 5610, 5700, 540, 6000, 6600, 3600V, 4000SU, 4120, 4121, 4130, 4131, 4140, 4190, 4200, 4330, 4340, 4410, 4600SU, 5100, 5200, 5340, 5900, 6610, 6700. Can replace Donaldson P02-0227, also replaces 101965A, 10P871, 1125804, 1508881M1, 3119347, 365413R1, 71125804, 73186, 73533, 80073533, C0NN9A663A, F3446R, L60631, R28794. (Item #: 157279, Ref: R28794) $7.80

Air Cleaner Cover Assembly - For tractor models 230, 231, 233, 234, 2600, 2600N, 2600V, 333, 334, 335, 3600, 3600N, 3600V, 3900, 4100, 4600, 515, 530, 531, 532, 5600, 6600, 7600. Replaces D0NN9661B, D1NN9661A, D5NN9661A, D8NN9661BA (Item #: 113722, Ref: D8NN9661AA) $105.00

Carburetor - This New Zenith Style carburetor outperforms the original carbs used on: 2600, 3000, 3400, 3600. New replacement Zenith carburetor. For 3 cylinder 175 CID engine. Replaces OEM# 13916, 13914, C5NE9510C, C5NN9510M, C7NN9510C, C9NN9510B, D3NN9510B, D6NN9510B, D8NN9510BA, D8NN9510C, E1NN9510BA, E1NN9510EA, R4100, R4120, R4120-1, R6863, R7893, R7896, R8553. Center to center on the 2 mounting bolts is 2 11/16 inches. Throttle linkage 3/4 inch from center of ball to center of shaft. (Item #: 184577, Ref: 13914B) $276.00

Carburetor - Zenith carburetor outperforms the original carbs used on: 2600, 3600N, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 334, 335, 340, 3400, 3500, 3600, 3600R, 3600V, 3610, 3610N, 3610V, 420. New replacement Zenith carburetor. For 3 cylinder 158 and 175 CID engine. Replaces OEM# C5NE9510C, C5NN9510M, C7NN9510C, C9NN9510B, D3NN9510B, D6NN9510B, D8NN9510BA, D8NN9510C, E1NN9510BA, E1NN9510EA, LIST6852, R3013-3, R4100, R4120, R4120-1, R6863, R7893, R7896, R8553 . Center to center on the 2 mounting bolts is 2 11/16 inches. The throttle linkage 3/4 inch from center of ball to center of shaft. Made in USA, 1 year warranty. (Item #: 100760, Ref: 13914) $564.00

Friction Disc for Throttle Control Lever - This Throttle Friction Disc is 3 inches in diameter and has a 1/2 inch center hole. Replaces part number C5NN518B, 83924272, 83977032, 9N518, E6NN9R536AA, 311503. (Item #: 111446, Ref: C5NN518B) $1.80

Fuel Cap, Vented - 2-7/8 inch outside diameter, silver finish, 1-3/4 inches edge of tang to edge of tang, vented, includes gasket. For tractor models 2111, 2120, 2130, 2131, 2150, 2300, 2310, 2600, 2600V, 2610, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 3330, 3430, 3600, 3600V, 3610, 3900, 3910, 3930, 4000, 4030, 4031, 4040, 4100, 4110, 4121, 4130, 4131, 4140, 4190, 4200, 4330, 4340, 4410, 4500, 4600, 4600SU, 4610, 4630. (Item #: 184806, Ref: C5NN9030D) $9.00

Fuel Filter Screw Kit - Used on many tractors, this screw kit is used in CAV style diesel fuel filter assemblies. Replaces OEM numbers D2NN9N090B, 81829151, 7111-604, 7111-860. Used on Ford: 2000, 2100, 2110, 2120, 2300, 231, 2310, 233, 2600, 2600N, 2600V, 2610, 2810, 2910, 3000, 3055, 3100, 3120, 3300, 3310, 333, 3330, 335, 3400, 3500, 3550, 3600, 3600N, 3600V, 3610, 3900, 3910, 4000, 4100, 4110, 4140, 420, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4600SU, 4610, 5000, 5100, 5110, 515, 5200, 531, 532, 5340, 535, 5600, 5610, 5700, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8210 (Item #: 179631, Ref: D2NN9N090B) $8.00

Fuel Injector Seal Kit - For (1) injector on: post 1965 tractors with 3 -6 cylinders models. Includes cork dust seal, copper compression seal and 2 aluminum return line seals. Replaces Replaces: 380428S, 380428S43, 81806142, 81806277, 81821105, 81867564, 83995430, C5NE9E529A, C5NE9F596A, C5NE9G546A (Item #: 156291, Ref: C5NE9F596A) $2.10

Injection Line Set - Used with rotary injection pump. For tractor models: 2310 (1/1/81-2/28/90), 2600, 2600, 2610 (1/1/81-2/28/90), 2610 (V, 1/1/81-2/28/90), 2810 (1/1/81-2/28/90), 2910 (1/1/81-2/28/90), 3600, 3610 (1/1/81-2/28/90), 3610V, 3610 (NO, 1/1/81-2/28/90), 3900 (1/1/75-later), 3910, 4110 (1/1/81-2/28/90), 4600, 4600SU (1/1/75-later), 4610 (1/1/81-2/28/90), 4610 (V, 1/1/81-2/28/90), 4610 (N, NO, 1/1/81-2/28/90), 4610SU (1/1/81-2/28/90). Compatible with Ford Construction and Industrials: 230A (1/1/81-2/28/90), 231 (1/1/75-later), 233 (1/1/75-later), 234 (1/1/81-2/28/90), 333 (1/1/75-later), 334 (1/1/81-2/28/90), 335 (1/1/81-2/28/90), 340, 340A, 340B, 420 (1/1/75-later), 445, 445A, 455 (7/1/87-11/30/88), 515 (1/1/75-later), 530A (1/1/81-2/28/90), 531 (1/1/75-later), 532 (1/1/75-later), 535 (1/1/75-later), 540, 540A, 540B, 545, 545A, 550, 555, 555A, 555B Replaces E0NN9A555AA, D9NN9A557AA, D9NN9A556AA. (Item #: 162827, Ref: FPL500) $46.00

Injector Pump Gasket Set - Fits CAV rotary pumps only. Replaces CAV9094713GV, CAV9094-713GV. (Item #: 178115, Ref: CAV9094-713) $37.00

Injector Pump Repair Kit - Fits DPA CAV 3, 4, 6 Cylinder Rotary Pumps only. Replaces OEM part number CAV7135-110. (Item #: 129312, Ref: CAV7135-110) $14.00

Hitch / Drawbar

Lower Lift Arm Pin Nut - Used on Category I lower lift arms, where the arm attaches to the axle housing, this nut is 5/8 UNF thread. Verify size before ordering. Many models have different size nuts. Replaces OEM numbers 83904384, 86637930, 87446, 33987S, 33987S36, 81419279, 701647, 353927X1, 170917423, 70917423, 6217938M1 (Item #: 178033, Ref: 353927X1) $1.80

Lower Lift Arm Pin Nut - Used internally on Category I lower lift arms, where the arm attaches to the axle housing, this nut is 5/8 UNF thread. Nylon Lock Nut. Verify size before ordering. Many models have different size nuts. Replaces OEM numbers 376450X1, 376267X1, 360262X1, 1679532M1 (Item #: 190743) $0.60

$Ford 3600V Lower Lift Arm R\H (Cat 1\1)$
Lower Lift Arm R/H (Cat 1/1) - Lower Link Lift Arm R/H (Cat 1/1) measures 32 7/8 inches in length, 3 9/16 in width, and 5/8 in thickness. Applicable for 20 0-4000 (4 cyl) 2000, 2100, 2110, 2120, 2150, 230, 231, 2310, 233, 2600, 2600N, 2600V, 2610, 2810, 2910, 3000, 3100, 3120, 3310, 333, 3330, 334, 335, 3400, 3500, 3600, 3600N, 3600V, 3610, 3610N, 3910, 3910N, 4000, 4110, 4110N, 4140, 4600, 4610, 4610N, 530, 531, 600, 601, 700, 701, 800, 801, 900, 901. Replaces 81815827 and E5NN555AA11Z. (Item #: 191080, Ref: C5NN555AN) $44.98

$Ford 3600V Lower Link Lift Arm (CAT 1\2)$
Lower Link Lift Arm (CAT 1/2) - Ford Lower Lift Arm R/H (CAT 1/2) measures 35 5/8 inches of length, 3 1/2 inches wide, and 11/16 in thickness. Applicable for 2000, 2000 US Built, 2100, 2110, 2110LCG, 2120, 2150, 2300, 230A, 230A US Built, 230AInd., 231, 231 US Built, 2310, 233, 250C, 2600, 2600 US Built, 2600N, 2600V, 2610, 2610 US Built, 2610V, 2810, 2910, 3000, 3000 US Built, 3055, 3100, 3120, 3300, 3310, 333, 3330, 334, 335, 335 US Built, 340, 3400, 340A, 340B, 345C, 345D, 3500, 3550, 3600, 3600 US Built, 3600N, 3600V, 3610, 3610 US Built, 3610N, 3610V, 3900, 4000, 4100, 4110, 4140, 420, 4200, 4330, 4340, 4400, 4410, 445, 445 US Built, 445A, 4500, 4600, 4600SU, 4610SU, 515, 530A, 531, 531 US Built, 532, 535, 540, 540A, 540B, 545, 545 US Built, 545A, 545C, 545D. Replaces 83954401. (Item #: 122628, Ref: E5NN555AA) $112.00

$Ford 3600V Lower Link Lift Arm L\H (CAT 1\2)$
Lower Link Lift Arm L/H (CAT 1/2) - Ford Lower Lift Arm L/H (CAT 1/2) measures 35 5/8 inches of length, 3 1/2 inches wide, and 11/16 in thickness. Applicable for 2000, 2000 US Built, 2100, 2110, 2110LCG, 2120, 2150, 2300, 230A, 230A US Built, 230AInd., 231, 231 US Built, 2310, 233, 250C, 2600, 2600 US Built, 2600N, 2600V, 2610, 2610 US Built, 2610V, 2810, 2910, 3000, 3000 US Built, 3055, 3100, 3120, 3300, 3310, 333, 3330, 334, 335, 335 US Built, 340, 3400, 340A, 340B, 345C, 345D, 3500, 3550, 3600, 3600 US Built, 3600N, 3600V, 3610, 3610 US Built, 3610N, 3610V, 3900, 4000, 4100, 4110, 4140, 420, 4200, 4330, 4340, 4400, 4410, 445, 445 US Built, 445A, 4500, 4600, 4600SU, 4610SU, 515, 530A, 531, 531 US Built, 532, 535, 540, 540A, 540B, 545, 545 US Built, 545A, 545C, 545D. Replaces 83954402. (Item #: 122627, Ref: E5NN556AA) $113.00

Hydraulic System

Hydraulic Lift Rocker Pin - This pin is used with C7NN535B, C7NN535C and E0NN535AA Top Link Rockers. The pin is number 4 in the image. Used on Ford 3500, 2000, 2100, 2110, 2120, 2150 1/70-12/74, U.K. Only, 330A, 2300, 231, 2310, 233, 2600, 2600N, 2600R, 2600V, 2610, 2610V, 3000, 333, 334, 335, 3600, 3600N, 3600R, 3600V, 3610V, 4000, 4110, 4600SU, 531 (Item #: 189212) $28.50

Hydraulic Pump Piston - Hydraulic pump piston with and diameter of 9/16. 6 used per piston, sold individually. Measure old piston before ordering as 2 different diameters were used on some models. Replaces 81801695 and C0NN882B. For models: 2000 3 cylinder, 2150, 2300, 2600, 2600V, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3600, 3600V, 4000 3 cylinder, 4000SU, 4100, 4190, 4200, 4330, 4340, 4410, 4600, 4600SU. (Item #: 184020, Ref: C5NN615A) $13.50

Hydraulic Pump Piston - Hydraulic pump piston with an diameter of 5/8. 6 used per piston, sold individually. Measure old piston before ordering as 2 different diameters were used on some models, Replaces 81801696. For models: Jubilee, NAA, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000 3 cylinder, 2000 4 cylinder, 2031, 2111, 2120 4 cylinder, 2131, 2150, 2300, 2310, 2600, 2600V, 2610, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3600, 3600V, 3610, 4000 3 cylinder, 4000 4 cylinder, 4000SU, 4031, 4100, 4120, 4121, 4131, 4190, 4200, 4330, 4410, 4600, 4600SU, 4610, 6000. (Item #: 184993, Ref: NCA615C) $11.10

Hydraulic Pump Repair Kit - Major repair kit for engine mounted pumps: C5NN600AA, C7NN600Y, C5KNN600AB, C7NN600Z all 1965 and up. D477600C and D6NN600A both 1975 and up. (Item #: 107998, Ref: CKPN600A) $35.00

Lift Cylinder Safety Valve - For tractor models: 2000 (4 cylinder 2120, 2150, 2300, 230A, 231, 2310, 233, 234, 2600, 2610, 2810, 2910, 3000, 3055, 3110, 3120, 3150, 3300, 3310, 333, 3330, 334, 335, 340, 3400, 340A, 340B, 3500, 3600, 3600V, 3610, 3900, 3910, 4000, (4110, 4120, 420, 445, 445A, 450, 4600, 4600SU, 4610, 515, 545A, 600, 6000, 601 1962-1964, ) 650, 660, 701, 800, 801, Dexta, Super Dexta. Also replaces 957E9842 and C5NN984A. (Item #: 169627, Ref: 957E984B) $21.00

Lights

Light Switch, Rotary Type - This Rotary Type Light Switch is used on many Ford/New Holland models 1965 and later. It replaces original part numbers C5NN11654A, C5NN11654D, C7NN11654B, C7NN11654C, D5NN11654B, E7NN11654AA, 83959708, D10026500, 83959708, 81818781, 81818408, 83905863. (Item #: 121197, Ref: E7NN11654AA) $13.20

Sealed Beam Bulb - This Sealed Beam Bulb is 12 Volt, 40 Watt, 3 Lug Terminal Type. It is 4-1/2 inch diameter. Replaces 83910047, 3072947R91, 3070494R91, K962146, D6NN13N007A, 54051293, 81806938, C5NN13N007A, ATJ8746, 535505M1, K915874 (Item #: 124720, Ref: D6NN13N007A) $26.80

Oil System

Oil Filter, Spin-On - Spin on style oil filter measures with dimensions of 5 13/32 inches in length, 3 11/16 inches O.D. Fits Tractor Models: NAA, Jubilee, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 2600, 2610, 3000, 3600, 3610, 4000, 4600, 4610, 5000, 5600, 5610, 6600, 6610 from 1965 to 10/1969. For use with spin on filter adapter 309825. (40538S)Replaces 237000, 4511629, 70237000, 74511629, C9NN6714A, 1959757C1, 388227R1, 918266R93, 920203C1, A146696, A17415, A33487, A37189, E36534, G45210, G45306, 500462, 86546614, 86546614DS, C1AZ6731A, C3AE6714A, C5NE6737B, D9NN6714EA, E7NN6714A, E7NN6714AA, 1851658, TY9425, TY9425E, 159045A, 83963907, 87800083, 83947505, 89832924. Please verify OEM number before ordering. (Item #: 118399, Ref: E7NN6714AA) $14.20

PTO / Driveline

PTO Cap - Fits most Ford Tractors 1939 and later. Replaces part numbers 81809440, 310088, 80310088, 310088F, 0310088F (Item #: 109510, Ref: 310088) $7.80

Steering

Power Steering Pump - This Power Steering Pump replaces pumps with an internal Relief Valve (will not replace external relief valve. For 3500, 3550 5/1970 and up, 5100, 7100 7/1970 and up, 4100 4/1970 and up, 4600, 5600, 6600, 7600 5/1981 and up, 5610, 6610, 7610 4/1985 and up. Power Steering Pump with reservoir. Pressure relief valves set at 1100 PSI, 2.74 GPM. This pump can replace: 83949432, E6NN3K514DA. 2000, 3000 10/1968 and up, 2600, 3600, 4100, 2610, 3610, 4110 less cab, 83959550 - E6NN3K514CA. 4000 (10/1968-3/1970), 2600, 3600, 4110 with cab. Fits others replacing the following OEM numbers: D8NN3K514GA, D8NN3K514GB, D8NN3K514GC, E6NN3K514EA, 83917191, 83923736, 83924995, 83959533, 87759440, A709527 (Item #: 113209, Ref: E6NN3K514EA) $182.80

Power Steering Seal Kit - This Power Steering Seal Kit is used on steering gear assemblies. It contains (1) C9NN3747A, (1) C9NN3E614A, (2) C9NN3A590A, (2) C9NN3D624B, (1) E1NN3N632AA. Replaces EGPN3N503AA, 83957121 (Item #: 168433, Ref: EGPN3N503AA) $8.70

Reservoir Cap, Power Steering Pump - Used on E6NN3K514EA, D8NN3K514GC, C9NN3A674D Power Steering Pumps. For tractor models 231, 233, 2600, (3500, 3550 5/1970 to 1975), 3600, (4100 4/1970 to 1975), (420, 4600, 5600, 6600, 7600 1975 to 1981), 4600SU, (5100, 7100 7/1970 to 1975) and others. (Item #: 121241, Ref: D2NN3A006B) $3.60

No
Picture
Spindle Bushing - For tractor models 2000 (4-cylinder, 1962-1964), 2110, 2120, 2150, 2300, 230A, 231, 2310, 233, 234, 2600, 2600V, 2610, 2810, 2910, 3000, 3055, 3110, 3120, 3150, 3300, 3310, 333, 3330, 334, 335, 3600, 3600V, 3610, 3900, 3910, 4000 (4-cylinder, 1962-1964), 4110, 4120, 4140, 4600SU, 530A, 531, 541, 600, 601 Series, 800, 801 Series, Dexta, Super Dexta. Measures 1.352 inch inside diameter, 1.474 inch outside diameter and 1.490 inch length. Also replaces 81717392, 83928345 and 957E3110B. (Item #: 100632, Ref: NCA3110A) $4.40

Spindle, Left Hand - Has the following measurements (see image): A- 11.687 inches, B- 1.246 inches, C- 1.340 inches, D- 1.250 inches, E- 0.750 inches. It is used on the Left Side of the following VINEYARD models, 2300V, 2600V, 3300V, 3600V, 3910V, 4110V, 4610V. It replaces original part number C5NN3106S (Item #: 104531, Ref: C5NN3106S) $292.88

Spindle, Right Hand - Has the following measurements (see image): A- 11.687 inches, B- 1.246 inches, C- 1.340 inches, D- 1.250 inches, E- 0.750 inches. It is used on the Right Side of the following VINEYARD models, 2300V, 2600V, 3300V, 3600V, 3910V, 4110V, 4610V. It replaces original part number C5NN3105V (Item #: 104530, Ref: C5NN3105V) $156.98

Wheels

Lug Nut, Rear Wheel - 5/8-18 (UNF) Thread. Uses a 1 1/16 inch wrench. Replaces C5NN1120F, 8N1134, 881162M2. (Item #: 109991, Ref: 8N1134) $1.90

Rear Rim Bolt Kit - This Rear Rim Bolt Kit is a set of six bolts, nuts and washers. They are 5/8 inches-18 x 2.82 inches long. Replaces: 33806S34, 33806S36, 33806S7, 350719S8, 370938S36, 370938S43, 408, 81821369. (Item #: 184824, Ref: 350719KIT) $23.50

Rear Wheel Bolt - This Rear Wheel Bolt is used from rear axle to center disc. 5/8 inch-18 thread (UNF) x 2-3/16 inch Use with nut 8N1134. Used on tractors 1965 and later. Verify measurements and part numbers before ordering. Replaces C5NN1117D, C5NN1117K, C5NN1117R, VPH6506, VPH6534, 184272M1, 81815835, 893017M1, 98A625 (Item #: 108655, Ref: C5NN1117R) $2.88

Spindle Tab Washer - This Tab Washer is used on some Ford Tractors 1939-and later. Measures 1.50 inches (38.20mm) outside diameter, .775 inch (19.70mm) inside diameter, 0.0625 (1.23mm) inch thick. It replaces original part numbers 957E1195, 81802388, 83910701, 898349M2, 180010M1, 180010M2 (Item #: 173191, Ref: 957E1195) $1.50

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $365.01

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Cooling System

Thermostat Housing to Block Gasket - Tractors: all 4-cylinder, 1953-1964, gas and diesel. Bolt holes measure 3/8 inch in diameter, and center to center of bolt hole spacing is 2 3/4 inches. Sold and Priced as Each. (Item #: 191970, Ref: EAF8255A) $5.20

Decals and Emblems

Decal, Fear This Ford - 12-1/2 inches x 3 inches. For all Ford tractors. (Item #: 183476, Ref: S.67825) $15.87

Sherman Transmission Instruction Plate - For Ford models with Sherman step up step down transmission. Installs under steering wheel nut. (Item #: 178113, Ref: SHERMAN) $20.40

Drive Train

Shift Cover Plate Gasket - For all models with 5-SPEED transmission built between 1955-1964. Not for tractors made overseas, such as Major, Dexta, etc. (Item #: 178105, Ref: NDA7223A) $7.10

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $94.00

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.50

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.90

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.20

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter Solenoid, 12 Volt - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. (Item #: 150223, Ref: DR1467) $19.70

Switch, Push Button - This 2 terminal switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch overall length. Check measurements before ordering if using as a universal part. Applications include ether switch, horn button, cold start, starter switch, and manifold heater switch. It replaces 22702, 240962, 242988, 245866, 245936, 70253322, 71191589, 72160068, VT507, 86900358, A30858, O9995AB, T18524, TG07803, TO18117, TO7803, 271179R91, 367678R91, 373611R91, 393209R91, AR46184, AR47373, AR47374, R39554, 189158M91, 767828M91, 105386A, 10A972, 1K7392C, UT2421, 1K7392A, 7A7392. (Item #: 121141, Ref: R7994) $12.00

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Pistons and Sleeves

No
Picture
Seal Kit - Seal kit, for cylinder E2NN3A540BA. Piston rod is retained with 1" snap ring and 1-3/4" threaded spanner nut. (Item #: E2NN3X-SK) $64.99

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $78.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $108.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $176.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00

Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00

$Ford 3600V Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10

$Ford 3600V Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$Ford 3600V Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.80

$Ford 3600V Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40

$Ford 3600V Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60

$Ford 3600V Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40

Rain Cap - This rain cap is for a 4.00 inch pipe. (Item #: 108645, Ref: R1807) $11.00

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60

Rain Cap - This rain cap is for a 5.00 inch pipe. (Item #: 108750, Ref: WC15) $16.90

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.50

Fuel System / Air Intake

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $12.70

Filter Screen and Gasket for Sediment Bowl - 1-1/2 inch outside diameter seal (for a 1 9/16 inside diameter housing and a 1 3/8 inch outside diameter screen. Measure before ordering. For tractor models (1958-1964 All with 134 cubic inch engines), 2000 4 cylinder, 501, 601, 701, (1958-1960 all with 172 cubic inch engines up to 126524), 801, 901, 1801. (Item #: 150700, Ref: ABC346) $5.40

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.10

Gauges

Ammeter, Black, Flat Bezel - For all models to 1958. Terminal type ammeter. 30-0-30. Black ring. Replaces FAD10850A. (Item #: 110410, Ref: A0NN10670A-BLAC) $6.98

No
Picture
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $59.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $39.90

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $14.90

Hitch / Drawbar

Drawbar - Number Of Drawbar Holes: 11 Hole``Made of 1" x 2-1/2" high carbon steel``Category: 1``Length: 26"``End Pins: 7/8"``Hitch Pin Holes - 3/4" (Item #: 103174, Ref: 9N5182) $44.30

Drawbar Check Chain Kit - This Drawbar Check Chain Kit includes: right hand/left hand anchors, 2 eyelets, 2 chains, 4 clevis with pins, and hardware. Fits: Jubilee, NAA, NAB, 2000 3 Cylinder, 2000 4 cylinder, 2600V, 2N, 3600V, 4000 4 Cylinder, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 2030, 2031, 2100, 2110, 2111, 2120, 2121, 2130, 2131, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3110, 3120, 3300, 3330, 3600, 3610, [4030, 4130, 4140 (4 cylinder)], 4031, 4040, 4100, 4110, 4120, 4121, 4131, 9N, Industrial: 231, 233, 333, 334, 335, 1801, 1811, 1821, 1841, 1871, 1881, 230A, 3400, 3500, 530A, Dexta, Super Dexta. Replaces: 957E597, 957E596, CBPN598A, NCA597B, NCA596B. (Item #: 115051, Ref: NCA596B) $38.00

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.28

Link End - Plated, forged, 1-1/4 inch thread, left hand, 1 inch hole. (Item #: 180473, Ref: RE1717L) $20.50

Link End - Plated, forged, 1-1/4 inch thread, right hand, 1 inch hole. (Item #: 174507, Ref: RE1718R) $21.58

Stabilizer Arm HD - Arm only, made of alloy spring steel, for kit 231253XHD, red only. 7/8 inch hole diameter. 31 1/2 inches center to center. (Item #: 110516, Ref: 230042XHD) $15.30

Top Link - Forged Top Link, 12 inch body, Category I implement ends. Adjusts 17.5 to 24 inches overall. 3/4 inch pin holes and both eyelets are 1 3/4 inch wide. Dichromate plated. (Item #: 103162, Ref: JSA1012C) $19.98

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System

Coupler Flange - FORD: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b (Item #: 108772, Ref: L36-6) $119.41

Coupler Flange - Drive flange; 3/4 inch round bore with set screw 1/4 inch x 3/8 inch. 1-15/16 inch spacing. For Morflex series 302. Replaces: L363, 191061, 1752219M91, L36-3 (Item #: 112104, Ref: 191061) $22.00

Coupler for Pump Shaft - The Hydraulic Pump Shaft Coupler is 1-1/2 Outside Diameter and 2-1/4 inches long. It 7/8 inch 13 splined inside. It replaces 1631413, 350-1631413, S340 (Item #: 114586, Ref: S340) $36.00

Cylinder Seal Kit, For 2 inch cylinders - For TISCO side and top link replacement cylinders. Seal Repair Kit for 2 inch cylinders. For cylinder numbers: HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. (Item #: 183971, Ref: HSK2002) $23.90

Cylinder Seal Kit, For 3 inch Cylinders - For TISCO brand side and top link replacement cylinders ONLY. Seal Repair Kit for 3" cylinders. For cylinder numbers: HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. (Item #: 179480, Ref: HSK3002) $31.40

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $25.70

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $14.70

Hub - 7/8 inch, 13 spline threaded, 3-7/8 inch hole spacing. For 730 LOADER. Used with C5NNN879A hub. (Item #: 160204, Ref: 291315) $65.00

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199) $21.10

Hydraulic Pump for Loader - Part Description: Pump, Hydraulic For 730 LOADER, 735 LOADER. SPECS: CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, PORT SIZE INLET: 1-5/8 inches-12 ORB, PORT SIZE OUTLET: 1-5/16 inches-12 ORB, MOUNTING: 2 bolt SAE "B", FORD PUMP APPLICATION: 730 and 735 loaders, CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, MOUNTING: 2 bolt SAE "B", INLET: 1-5/8 inches-12 ORB, OUTLET: 1-5/16 inches-12 ORB. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inches and Maximum is 6 7/8 inches. (Item #: 127269, Ref: 7702425-29Z) $760.00

Hydraulic Pump, Front Mounted - This Hydraulic Pump is used with some 701, 702 and 703 Loaders. It is 14 Gallons Per Minute at 2000 RPM. The shaft is 3/4 inch round with a key way. Left Hand Rotation. Inlet is 1 Inch NPT. Outlet is 3/4 Inch NPT. Mounting bolt spacing 4 3/16 inches center to center. Comes with two adapters. Contains: 1-720FSO-3/4X3/4 HC4008 adapter, 1-720FSO-1X1-1/4 HC4009 adapter. This Pump may work in other loader application. Verify Specs before ordering. (Item #: 182700, Ref: L827-10X-LB) $585.00

Hydraulic Valve Kit - Valve with handles, three-spool, 2000 p.s.i. Relief, all spools tandem (4-way) spring center to neutral. (Item #: HV4030) $787.98

LBP Coupler Center - Center member. Center member. 3-5/8" O.D., four 5/16" holes, 2-1/4" bolt circle (L52-10) For tractor models 352. (Item #: 178931, Ref: 192169) $71.00

LBP Hydraulic hose Assembly - Hydraulic hose assembly. For Ford model 740 LOADER. (Item #: 179521, Ref: 7701142) $29.70

Morflex Center Member - This is a 1-302 Morflex Center member. It measures 3-1/8 inch diameter, four 1/4 inch holes, 1-15/16 inch bolt circle. Replaces part numbers 893129, 191192, L5227, 1506097M91, 1086870M1, 191192LBP, 1752218M91, L52-27 (Item #: 116952, Ref: 191192LBP) $52.92

Top Link, Hydraulic - FORD: Hydraulic top link cylinder. All ports 9/16 inch-18 O-ring boss with two adapters 9/16 inch-18 ORBM x 1/4 inch NPTM 90 degree swivel. 3 inch cylinder bore, 8 inch stroke length, 26 inch closed length, 12-7/16 inch barrel length, 1 inch rod end diameter, 1-3/4 inch rod end width, 1 inch diameter base end. (Item #: 167145, Ref: HTL3103) $273.00

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.60

Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.60

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $120.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.70

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.80

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $98.00

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights

Headlight Assembly, 12 Volt - (Single) Headlight Assembly 12-volt, blue - Sealed beam headlamp assembly in heavy gauge steel housing with Rubber bezel. Does not look like original. (Item #: 184496, Ref: L525HB-12V) $51.00

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

No
Picture
Sealed Beam Bulb, 12 Volt - Red/white combination work/tail light, 4-1/2 inch diameter. (Item #: 116014, Ref: S.52670) $23.60

Tail Light Lens - Plastic 4 inch lens for DUOLAMP with FOMOCO stamped on lens (has 2 mounting screw holes spaced 3 1/8 inches apart). Fits tractors 1953 and newer. (Item #: 178144, Ref: FDV13450A) $16.50

Miscellaneous

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Tractor Umbrella with Frame & Mounting Bracket - Blue - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without Additional Handling & Oversize Fees Apply To This Item, tools, (Item #: 161190) $119.00

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40

No
Picture
Paint, Brownish Medium Gray, 1 Quart - Ford Brownish Medium Gray was used for the same applications as TP240Ford Medium Gray. This is a lighter shade. Since the tractors did not come off the production line all the same, the darker or light shades are completely up to the desires of the customer. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184575, Ref: TP245QT) $50.00

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $68.00

No
Picture
Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20

No
Picture
Paint, Empire Blue, 1 Gallon - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100713, Ref: TP360GAL) $56.00

No
Picture
Paint, Empire Blue, 1 Quart - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100712, Ref: TP360QT) $23.30

No
Picture
Paint, Empire Blue, Spray Can - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100711, Ref: TP360SP) $7.40

No
Picture
Paint, Ford White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108135, Ref: TP470GAL) $82.00

No
Picture
Paint, Ford White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108133, Ref: TP470SP) $10.20

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $55.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100120, Ref: TP2700SP) $8.90

No
Picture
Paint, Industrial Yellow, Spray - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100723, Ref: TP760SP) $7.80

No
Picture
Paint, Light Gray, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100716, Ref: TP330GAL) $57.00

No
Picture
Paint, Light Gray, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100715, Ref: TP330QT) $20.70

No
Picture
Paint, Light Gray, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100714, Ref: TP330SP) $8.90

No
Picture
Paint, Medium Gray, 1 Quart - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100718, Ref: TP240QT) $22.10

No
Picture
Paint, Medium Gray, Spray Can - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100717, Ref: TP240SP) $8.30

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $60.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $16.90

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.90

No
Picture
Paint, Vibrant Blue, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156586, Ref: TP365GAL) $91.00

No
Picture
Paint, Vibrant Blue, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156587, Ref: TP365QT) $37.20

No
Picture
Paint, Vibrant Blue, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156585, Ref: TP365SP) $10.40

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $44.10

PTO / Driveline

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $173.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

NOTE

PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.

NOTE

PTO Overide Clutch - This 6 spline Override Coupler converts a 1 1/8 inch diameter PTO shaft to 1 3/8. It has a 1 1/8 inch female at one end and 1 3/8 inch male at the other end). Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103169, Ref: C670F) $51.00

PTO Overide Clutch - Override coupler for 1 3/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 191020, Ref: C680F) $79.00

PTO Overide Clutch - Override coupler for 1 1/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103167, Ref: C690F) $67.80

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $279.00

Seats

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57

Seat Cushion, Black - Cover with piping and Ford script logo. Fits all 1939-1964 models with a 17 inch wide steel seat pan. (Item #: 115058, Ref: 8N401BLK) $51.00

Tie-On Seat Cover - Blue and White, 19 inches wide. Deluxe with 2 inches of foam. (Item #: 101353, Ref: R1013) $36.10

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $103.00

Sheet Metal / Body Parts

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $178.00

Steering

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $48.40

Steering Wheel Spinner Assortment - Complete wheel spinner assortment: includes 2 blue, 2 green, 3 red, 2 yellow and 3 black. (Item #: 185079, Ref: WSV125A) $123.80

Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16 inches x 5/8 inch x 5/8 inch, 1 15/16 inches x 3/4 inch, 3/4 inch, and 1 3/8 inches x 1 inch x 1/2 inch. (Item #: 183427, Ref: TIERODBOOTS) $13.00

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $24.30

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $307.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. (Item #: 103768, Ref: FW60166) $92.00

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166) $70.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $18.30

No
Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $64.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $66.00

Wheel Clamp - Wheel clamp holding disc to rim for double ramp type on power adjustable rims. For 28 inch rim on tractors 2000, 3000, 4140, (10-1968 to 1975); 2600, 3600, 4100, 4600SU except Baseldon models, (1981 to 3-1990); 3230, 3430, 3930, 4130, 4630, 4830LCG, (3-1990 to -) Use with rims PAR10X18 and C5NN1050J and C5NN1050H. Also replaces 3615259M1, 70235676 and 7000000241, E5NN1043AA. (Item #: 124526, Ref: 898021M1) $18.00

Wheel Front 8X16 - Front Wheel 8 inch x 16 inch ; 6 bolt, 6 inch circle, 4.62 inch pilot. (Item #: 180445, Ref: D5NN1007A) $106.00