Brake Disc - For tractor models (5100, 520, 7100, 7200 1965-1975), (5600, 5700, 6600, 6700, 7600, all 1975-1980), (5610, 6610, 6710, 7610, 7710, 7910, all 1981 and up). Intermediate Steel Brake Disc 8.819 inch O.D. and 2.086 inch I.D. 22 Teeth. 5/8 inch wide facing. C7NN2A097B, C5NN2A097A, 83956599, E6NN2A097AA, 83956599. (Item #: 122174, Ref: C7NN2A097B)$26.20
Brake Disc, 9 Inch - With 1-9/32 inch wide lining, this disc was used in later production than the 5/8 width lining. This disc is 8 7/8 inches outside diameter, 2 1/8 inches inside diameter, facing width 1.31 inches, 22 internal tooth count. Used with 9 inch actuators. This part replaces Ford part numbers E9NN2A097BA, E9NN2N097BA, 83989830, 81818854, 83956599, E6NN2A097AA, 87518036, C7NN2A097B. (Item #: 105499, Ref: E9NN2A097BA)$25.50
Brake Disc, Intermediate Steel - Used with 9 inch actuators, this intermediate steel disc measures 8.976 outside diameter and 5 inch inside diameter. This part replaces Ford OEM numbers E6NN2N315AA, E6NN2N615AA, 83956598. Used on the following with 9 inch actuator disc brakes: 3600, 4600, 5000, 5100, 5110, 5200, 532, 5340, 5500, 5550, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 650, 6500, 660, 6600, 661, 6610, 6610S, 6640, 6700, 6710, 681, 6810, 7000, 7010, 7100, 7200, 7410, 755, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8030, 8210, 8240, 8340, TS100, TS110, TS120A, TS6000 Brazilian, TS6020 Brazilian, TS6030 Brazilian, TS6040 Brazilian, TS80, TS90 (Item #: 105513, Ref: E6NN2N315AA)$14.70
Brake Pedal Shaft - For Ford tractor models 5000, 5100, 5110, 5200, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6810, 7000, 7100, 7200, 7600, 7610, 7700, 7800, 7810, Replaces Ford OEM number D2NN2478C, 83927298, D9NN2N337EA, (Item #: 154952)$31.00
Brake Shaft Felt Seal - This Brake Shaft Felt Seal measures 1.470 inch outside diameter, 0.925 inch inside diameter and 0.360 inch thick. Replaces 81826045, 8N3586, D2NN2N171A, 86553476, C5NN3586A (Item #: 124494, Ref: 8N3586)$2.20
Brake Shaft Seal - This Brake Shaft Seal measures 1.565 inch outside diameter, 1-1/16 inch inside diameter. It replaces original part numbers C5NN2473F, C5NN2473H, C5NN2N258C, D2NN2N258A, D8NN2N289AA, D9NN2N289AA, 65968, 83924047. (Item #: 150914, Ref: D9NN2N289AA)$3.30
Disc Brake Ball Bearing - Measuring 7/8 inches, this ball bearing is used in many disc brake systems. Typically 4 or 6 used per wheel. Replaces OEM numbers 09384AB, 150734A1, 16028R1, 166264, 16779X, 17028R1, 20063060, 2073622, 211-1028, 211-1328, 211-19, 211-221, 31-1750393, 33-0026328, 50A4272, 706039R1, 706039R2, 72073622, 7A2606, 0166264, 81716998, 81847078, 81866502, 82979987, 87554519, 87672308, 9170150, 920095936, 9959976, 9960587, BDB78, D5NN2N141A, E94FB9, E9NN2N324AA, E9NN2N324AB, GM145662, K963645, M830T, O9384AB (Item #: 126209, Ref: M830T)$2.90
Hand Brake Disc - Diameter 4 inches, 1-1/4 inch hub, 23 splines. Also replaces: D5NN2N625A and C5NN2N625B. Fits Tractors: (2000, 3000, 4000 all from 1965 and newer - UK), (2000, 3000, 4000 all from Jan/1972 and newer - USA), 2310, 2600, 2610, 2810, 2910, 3600, 3610, 3900, 3910, 4100, 4110, 4600, 4610, 5600, 5610, 5900, 6600, 6610, 6700, 7600, 7610, 7700, 7710. Fits INDUSTRIALS: 230, 231, 233, 234, 333, 335, 340, 3500, 3550, 420, 4400, 4500, 445, 450, 515, 531, 532, 540, 540, 545, 5500, 5550. Replaces C5NN2N625B, D5NN2N625A, E9NN2N625AB, 83906199, 81867258 (Item #: 105495, Ref: E9NN2N625AB)$32.00
Hand Brake Repair Kit - This Hand Brake Repair Kit contains Rod. Knob, Pawl and Spring. Replaces 81816243, C7NN2N606B, C7NN2N616D, C5NN2N615B, 81708853, E0A2744, 81819533, 81819534, 81876606 (Item #: 183910, Ref: S.66303)$18.50
Intermediate Steel Brake Disc - For tractor models (5100, 5200, 7100, 7200, all 1965-1975), (5600, 5700, 6600, 6700, 7600, 7700, all 1975-1980), (5610, 6610, 6710, 7610, 7710, 7910, all 1981 and up). Intermediate Steel Brake Disc, 9 inch diameter. (Item #: 105513, Ref: C5NN2N315A)$14.70
Clutch Kit, 10 SPLINE DISC - This new complete clutch kit includes: a 12 inch, 10 spline, with 1.75 inch hub, rigid clutch disc (E7NN7550DA), a 12 inch, 4 finger pressure plate (86634458), a sealed type release bearing that measures 2.49 inch inside diameter, 4.06 inch outside diameter, .87 inch width (83914247), a pilot bearing that measures 1.43 inch inside diameter, 2.68 inch outside diameter, .59 inch width (F0NNN779AA) and clutch alignment tool. For models: 4600, 4600SU, 5000, 5190, 5340, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 7000, 7600, 7700. (Item #: 112319, Ref: E0NN7550DA)$250.00
Clutch Kit, 13 Inch Single - This Kit contains 13 inch - 10 spline spring drive disc with 1 3/4 inch hub 82011593, 13 inch single pressure plate w/ring D8NN7563AB, pilot bearing F0NNN779AA and release bearing 83914247, includes pilot tool. Replaces 82006046, 82011593, D8NN7563AB (Item #: 112322, Ref: 11126087)$350.00
Clutch Kit, 25 SPLINE DISC - This new complete clutch kit includes: a new 12 inch, 4 finger pressure plate (86634458). A 12 inch, 25 spline, 1 5/8 inch hub rigid disc (C7NN7550Z). A new release bearing which measures 2.49 inch inside diameter, 4.06 inch outside diameter, .82 inch width (83914247), pilot bearing measures 1.43 inch inside diameter, 2.68 inch outside diameter, .59 inch width (F0NNN779AA) and clutch alignment tool. For tractor models 4600, 4600SU, 5000, 5190, 5340, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 7000, 7600, 7700. (Item #: 112321, Ref: E0NN7563CA-KITA)$310.00
Clutch Kit, 25 SPLINE DISC - Complete Kit is the same description as E0NN7563CA-KITA except Disc has springs not rigid. Disc, 12 inch, 25 spline SPRING disc, 1 5/8 inch hub, pressure plate is 4 finger, release bearing measures 2.49 inch inside diameter, 4.06 inch outside diameter, .82 inch width, pilot bearing measures 1.43 inch inside diameter, 2.68 inch outside diameter, .59 inch width and alignment tool. For tractor models 4600, 4600SU, 5000, 5190, 5340, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 7000, 7600, 7700. (Item #: 112320, Ref: E7NN7550DA-KIT)$273.00
Clutch Kit, Remanufactured - For Ford tractor models 5000 (10/71-9/75), 5100 (10/71-9/75), 5110 (10/71-9/75), 5190 (10/71-9/75), 5200 (10/71-9/75), 5340 (10/71-9/75), 5600, 5610, 5700, 5900, 6410, 6600, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7700, 7710, 7800 (with Dual Power), Clutch Diameter - 13", Clutch Hub Diameter - 1-3/4", Clutch Splines - 10, Clutch Center - Spring, Clutch Type - 6 Large Pads, Pressure Plate Size - 13", Pressure Plate Levers - 4, Pressure Plate Springs - 16, Pressure Plate Type - Single Stage, For a New version of this sku use Item #: 112322, Additional Handling and Oversize Fees Apply To This Item, (Item #: 202043)$506.40
Clutch Kit - Single - This new complete clutch kit (for flat flywheel step) contains: a 13 inch single pressure plate, with ring (D8NN7563AB), 13 inch 10 spline rigid 1.75 inch hub disc (82011593), a pilot bearing that measures 1.437 inch inside diameter, 2.6772 inch outside diameter, .59 inch wide (F0NNN779AA), a release bearing that measures 2.5 inch inside diameter, 4.125 inch outside diameter, .870 inch wide (83914247), and clutch alignment tool. For tractor models: 4600, 4600SU, 5000, 5110, 5190, 5340, 5600, 5610, 5610S, 5700, 6410, 6600, 6610, 6610S, 6700, 6710, 6810, 6810S, 7000, 7010, 7600, 7610, 7610S, 7700, 7710, 7810, 7810S, 7910, 8010, 8210. (Item #: 112322, Ref: D8NN7563AB-KIT)$350.00
Clutch Pack Housing - This Clutch Pack Housing comes without clutches. It replaces original part numbers 83931457, D0NN7R036A, D0NN7R036B, D2NN7R036A, D2NN7R036B, D3NN7R036A, D5NN7R036A, D5NN7R036B, D6NN7R036A, D8NN7R036AA, E0NN7R036AA, E0NN7R036AB. (Item #: 179282, Ref: E0NN7R036AB-B)$410.00
Clutch Pedal Return Spring - This Clutch Pedal Return Spring is used on multiple Ford/ New Holland Tractors and Industrial Models, build 1965 and later. It replaces original part numbers C7NN7N598A and 81820895 (Item #: 153432, Ref: C7NN7N598A)$5.10
No Picture
Clutch Plate - For Ford tractor models 4600, 4600SU, 5000, 5100, 5190, 5200, 5340, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 6810, 7100, 7200, 7600, 7700, Replaces Ford OEM number E0NN7563CA, 83925716, (Item #: 166027)$91.98
Clutch Unit - Diaphragm, Remanufactured - For Ford tractor models TW5, TW10, 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7800, 7810, 7840, 7910, 8000, 8100, 8200, 8210, 8240, 8340, 8400, 8530, 8600, 8700, 9000, 9200, 9600, 9700, Compatible with New Holland tractor models TS80, TS90, TS100, TS110, 8010, Clutch Diameter - 13", Clutch Hub Diameter - 1-3/4", Clutch Splines - 10, Clutch Center - Spring, Clutch Type - 6 Pads, Pressure Plate Size - 13", Pressure Plate Type - Diaphragm, Additional Handling and Oversize Fees Apply To This Item, (Item #: 205234)$485.01
Clutch Unit, Remanufactured - For Ford tractor models 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7800, Clutch Diameter: 13", Clutch Hub Diameter: 1-5/8", Clutch Splines: 25, Clutch Center: Solid, Clutch Type: Woven, Pressure Plate Size: 13", Pressure Plate Type: Single Stage, Includes pressure plate and engine clutch disc only, Does not include bearings, Additional Handling and Oversize Fees Apply To This Item, (Item #: 206258)$460.01
Pressure Plate Assembly - For Ford tractor models TW5, TW10, 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7800, 7840, 8240, 8340, 8530, 8600, 8700, 9000, 9200, 9600, 9700, Compatible with New Holland tractor models TS100, TS110, Pressure Plate Size: 13", Pressure Plate Levers: Diaphragm, Pressure Plate Springs: Diaphragm, Pressure Plate Type: Single Stage, For a Remanufactured version of this sku use Item #: 206267, (Item #: 122250)$341.00
Pressure Plate Assembly, Remanufactured, D8NN7563AB, 86634446 - For Ford tractor models TW5, TW10, 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7800, 7840, 8240, 8340, 8530, 8600, 8700, 9000, 9200, 9600, 9700 Replaces Ford OEM number D8NN7563AB, , Compatible with New Holland tractor models TS100, TS110, Replaces New Holland OEM number 86634446, Pressure Plate Size: 13", Pressure Plate Levers: 4, Pressure Plate Springs: 16, Pressure Plate Type: Single Stage, Additional Handling and Oversize Fees Apply To This Item, (Item #: 206209)$196.00
No Picture
Pressure Plate, Remanufactured, E0NN7563CA - For Ford tractor models 5000, 5100, 5200, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, Compatible with Ford Construction and industrial models 6500, Replaces Ford OEM number E0NN7563CA, 86634459, Pressure Plate Size: 12", Pressure Plate Levers: 4, Pressure Plate Springs: 16, Pressure Plate Type: Single Stage, For a New version of this sku use Item #: 130093, Additional Handling and Oversize Fees Apply To This Item, (Item #: 205233)$181.00
Pressure Plate Shim Kit - Ford 5600, 5610, 5900, 6600, 6700 Pressure Plate Shim Kit. This is a 4 pack of .060 inch shims for 12 inch single clutch. Replaces E0NN7N596AA. (Item #: 182828, Ref: F1815815)$27.60
Release Bearing - This Clutch Release Bearing. Inside diameter 2.4997 inches, outside diameter 4.0700 inches, width 0.8700 inches. This is used in multiple Ford Tractors. Replaces original part numbers D8NN7580AA, D8NN7580BA, D8NN7580BB, E4NN7580AA, 82010859, 83914247, 83933520, 83946908, 86534551 and N3004. (Item #: 112189, Ref: N1585)$21.70
Spring - Spring for Clutch and Brake Lever Assist. Tractors: 3550, 4000 (11/1972 and up), 5100, 7100 (1965 and up), 420, 515, 532, 535, 4600, 5600, 5700, 6600, 6700, 7600, 7700, (1975 to 1981). (Item #: 164364, Ref: C5NN2472H)$4.90
Cooling Fan - 4 Blade, Used - For Ford tractor models 2000, 2110, 2310, 2600, 2610, 2810, 2910, 3000, 3230, 3400, 3430, 3600, 3610, 3900, 3910, 3930, 4000, 4000SU, 4100, 4110, 4400, 4500, 4600, 4600SU, 4610, 4610SU, 5000, 5550, 5600, 6600, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 250C, 333, 334, 335, 340, 340A, 340B, 420, 450, 455, 515, 530A, 535, 540, 540A, 540B, 545, 550, 555, 555A, 555B, 655, 655A, Replaces Ford OEM number 87017802, C5NN8600B, 81805721, C5NN8600A, 4 Metal Blades, Outside Diameter: 16", For a new version of this item use Item #: 155455, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 455455)$26.94
No Picture
Cooling Fan - 7 Blade, Used - For Ford tractor models 4830, 5000, 5030, 5110, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7410, 7600, 7700, 7710, Replaces Ford OEM number D3NN8600A, 81829494, 83910793, 87010708, Metal Blade Fan, Diameter: 17", Pilot hole: 0.625" (5/8"), Mounting Holes: 1.750" Center to Center, For a new version of this item use Item #: 155457, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435984)$37.01
Fan Belt - Fits 2600, 3600, 4100, 4600, 5600, 5700, 6600, 6700, 7000, 7600, 7700, 2610, 3610, 4110, 4610, 5610, 6610, 6710, 230A, 231, 334, 335, 420, 515, 530A, 531, 532, 535, 545D 650, 750, 755, 755A, 755B. Some of these tractors used more than one type of belt. Verify part number before ordering. 1/2 Inch (13 mm) x 55 7/16 Inches (1408 mm) raw edge v-belt. (Item #: 118363, Ref: D4NN10C318A)$10.50
Fan Blade - (17 inch) 7 Blade, Metal. Center hole is 3.25 inch. Bolt holes are 2.5 inches apart (measured in a square pattern) AND 4 inches apart (measured diagonally). Fits (5600, 6600, 6700, 7600, 7700, 8/76> less Air Cond), (7600, 7700 9/76-9/80 with Air Cond), (7710 7/81-10/88 less Air Cond). (Item #: 155458, Ref: E7NN8600DA)$51.00
Fan Blade - 4 Blade - Fan Assembly, 4 Blade, 16 inch diameter, 0.625 inch pilot hole, and mounting holes on 2.5 inch center. For tractor models 2000, 2310, 231, 233, 234, 2600, 2610, 2810, 2910, 3000, 333, 334, 335, 3600, 3900, 3910, 4000, 4100, 4110, 420, 4400, 4500, 4600, 4610, 5100, 515, 531, 535, 5600, 6600. Replaces 87017802, 81805721, C5NN8600B, C5NN8600A (Item #: 155455, Ref: C5NN8600A)$45.00
Fan Blade, 7 Blade - This new 7 Blade Fan has a 17 inch diameter, 0.625 inch pilot hole, and mounting holes on 1.75 inch center. Replaces D3NN8600A, 81829494, 83910793, 87010708. (Item #: 155457, Ref: 87010708)$63.00
Fan Blade - 8 Blade - For 3 and 4 Cylinder 1965 and up: 2000, 2310, 2600, 2610, 2810, 2910, 3000, 3230, 3430, 3600, 3610, 3910, 3930, 4000, 4100, 4110, 4130, 4600, 4610, 4630, 4830, 5000, 5030, 5600, 5610, 6000, 6600, 6610, 6700, 6710, 7000, 7600. 8 Blade, blue PLASTIC 5/8 inch pilot hole, 4 bolt with 2 1/2 inch center to center on opposite holes, 16 inch outside diameter. (Item #: 178625, Ref: S.60579)$35.00
Fan Shroud - Fits 17.5 inch Fan. The Shroud is used on 5600, 5610, 6600, 6610, 6810, 7010, 7600, 7610 Tractors with 17.5 inch fans. It replaces original part numbers 81869055, D3NN8146A, E2NN8146BB, E6NN8146AA (Item #: 171767, Ref: E6NN8146AA)$125.00
Radiator - For the following tractors without Oil Cooler: 4100 or 4600 (Diesels with cab and AC 1977>), 4500, 5000 (1965 to 1975); 5600, 6600 (1975 to 1981); 535 (1975 to 1978). Industrials: 340 (< 9/1985), 445 (without Torque Converter 10/1978 - 9/1986). Replaces D6NN8005B, C5NN8005N, 83918041, 83916894, 83916415. Measures core size: 17.500 inches wide, 17.750 inches high, 3 rows of tubes. (Item #: 101872, Ref: 86531508)$230.00
Radiator - This Radiator, with Oil Cooler is copper core. Core size 18 inches wide, 17-3/4 inches high, 4 rows of tubes, 8 fins per inch. Replaces D8NN8005KA, D5NN8005A. For tractor models 5600, 6600, 7600. All with diesel engines. (Item #: 101700, Ref: D8NN8005KB)$400.00
Radiator - This new Radiator is designed and built to precise dimensional specifications to ensure an exact fit. Each Radiator has a stamped brass tank, undergoes a rigorous quality inspection, and is 100% leak tested. This Radiator without an Oil Cooler has 7 fins per inch and 3 rows of tubes. It is 17.75 inches tall and the core size is 18 inches wide. It has a 24 inch overall height and 18 3/4 inch overall width. Confirm measurements before ordering. This radiator fits: 5000, 5100, 5600, 6600. Replaces C5NN8005E, C7NN8005E, C5NN8005SE. (Item #: 101866, Ref: C7NN8005E)$270.00
Radiator - Radiator Assembly with Oil Cooler on engine side for: (345C, 445C 12-88/12-9, (4500, 5000, 5100, 5200 all 1965 and up), 535 with TORQUE CONV., 545 with TORQUE CONV. 7/11-88, 5600 1975, 6600 1975, 6600C. (Item #: 101698, Ref: D8NN8005SB)$340.00
Radiator Cap - 13 PSI Radiator CAP (FOR 2000, 3000, 4000, 5000, 7000 1965 TO 1975), (2600, 3600, 4100 4600, 5600, 5700, 6600, 6700, 7600, 7700 1975 TO 1981), (2610, 3610, 4110, 4610, 5610 6610, 7610, 7710 1981 and up). REPLACES D2AE8100A1A. (Item #: 123522, Ref: E2NN8100BA)$5.60
No Picture
Radiator Drain Faucet - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2000, 2031, 2100, 2600, 2610, 3000, 3230, 3430, 3600, 3610, 3930, 4000, 4100, 4110, 4600, 4610, 4630, 5000, 5110, 5600, 5610, 5640, 5900, 6000, 6410, 6600, 6610, 6640, 6710, 6810, 7000, 7410, 7610, 7700, Compatible with Ford Construction and industrial models 1801, 1811, 1821, 1841, 1871, 1881, 2030 Replaces Ford OEM number 81465471, C9NN8115A, C5NN8115B, , Compatible with New Holland Harvester (s) 1880, 1890, 1895, 1900, 1915, 2100, Compatible with New Holland Baler (s) 1283, 1425, 1426, Compatible with New Holland Hay Cutting (s) 1100, 1112, 1114, 1116, 1118, 1469, 1495, 1496, 1499, Replaces New Holland OEM number 81465471, Fits all models with 1/4" NPT threads, (Item #: 176414)$4.90
Radiator Hose, Lower - This Lower Hose has an inside diameter on the small end of 1.645 inches and 1.757 on the larger end. For tractor models 445 Diesel and Gas, 450 Diesel and Gas, 4500, 535, 540 Diesel, 545 Diesel, 6500 Construction, 335, 5000, 5100, 5600 (without Oil Cooler), 5900 (without Air Conditioning), 6600 (without Oil Cooler), 7000, 7100, 7600 (without Oil Cooler). (Item #: 116911, Ref: C5NN8286C)$9.50
Radiator Hose, Upper - This Upper Hose is for Gas engines. Hose inside diameter 1.5 inch. Fits radiator upper. For 2000, 2310, 2600, 2610, 2810, 2910, 3000, 335, 3600, 3610, 3910, 4000, 4100, 4110, 420, 4600, 4610, 515, 532, 535, 5600, 5700, 6700, 7600, 7700. (Item #: 113921, Ref: C5NN8260D)$9.30
Water Pump - This water pump comes with a dual belt pulley. For 340A, 340B, 420, 445, 445A, 450, 515, 535, 540, 540A, 545, 545A, 555E, 6500, 750, 2600, 3600, 4600, 5600, 6600, 6700, 7600, 7700, 2610, 2810, 2910, 3610, 3910, 4110, 4610, 5610, 6610, 6710, 6810, 7410, 7610, 7710 (1/1981-10/1988). Replaces EGPN8A513CA, FAPN8A513DD. Water Pump with Dual Pulley and Gasket. The proper fan for this pump is part number D9NN8600AA. Bolt pattern on the hub for the pulley is 2.5 inches center-to-center across. (Item #: 100559, Ref: EAPN8A513E)$76.00
Water Pump - This Water Pump comes with Single Groove Pulley and Gasket. Does not come with back housing. Comes with back housing gasket. Replaces FAPN8A513GG. For 2000, 3000, 4000, 5000, 7000, 2600, 3600, 4100, 4600, 5600, 5700, 6600, 6700, 7600, 2310, 2610, 2810, 2910, 3610, 3910, 4110, 4610, 5710, 5610, 6610, 6710, 7610, 7710. Also replaces FAPN8A513GG. Uses Fan blade with 2-1/2 inch bolt spacing center-to-center. (Item #: 100558, Ref: EAPN8A513F)$41.00
Water Pump - For Ford tractor models 2000, 2100, 2110, 2120, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3120, 3230, 3300, 3310, 3330, 3400, 3430, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4200, 4330, 4340, 4400, 4410, 4600, 4600SU, 4610, 4610SU, 4630, 5000, 5100, 5110, 5200, 5340, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 250C, 334, 335, 340, 340A, 340B, 345, 345C, 345D, 420, 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 515, 530, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 655, 655A, 3500, 3550, 4400, 4500, Replaces Ford OEM number D3NN8501A, 87800115, 81814205, 81838685, 83905629, 83914192, 83919542, 83926000, 83943914, 88NY8501AA, C5NE8501A, C5NN8501A, D8NN8501CA, D8NN8501UA, D8NN8501UB, D8NN8501UC, For models without heater plug or cab heater, With Single Pulley, Includes: pump to backplate gasket, backplate, backplate to block gasket, For pump with heater hole use Item #: 115341, (Item #: 140587)$84.00
Water Pump Gasket - Used on multiple Ford models built 1965 and later. Replaces original part numbers D6NN8507A, E5NN8507AA, E5NN8507AB, C5NE9513A. (Item #: 117437, Ref: E5NN8507AB)$1.10
Water Pump Gasket - This is the Water Pump to Pump Housing Gaskets used in Ford/New Holland equipment, 1965 and later. It replaces original part numbers 83959398, E6NN8513AA. (Item #: 117438, Ref: E6NN8513AA)$3.80
Water Pump with Backing Plate and Double Groove Pulley - For Ford tractor models 2310, 2600, 2610, 2810, 2910, 3230, 3430, 3600, 3610, 3900, 3910, 3930, 4100, 4110, 4130, 4600, 4600SU, 4610, 4610SU, 4630, 4830, 5100, 5110, 5600, 5610, 5700, 5900, 6410, 6500, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 333, 334, 335, 340, 340A, 340B, 420, 445, 445A, 450, 515, 530, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 550, 555, 555A, 555B, 650, 655, 655A, 750, 755, 755A, 755B, 7500, Replaces Ford OEM number D3NN8501B, E6NN8501CA, E6NN8501CB, D8NN8501DA, D8NN8501TA, D8NN8501TB, D8NN8501TC, D8NN8501TD, D5NN8501F, D8NN8501TE, Replaces New Holland OEM number 83914193, 83919541, 83925999, 83909539, 81876233, 3943913, 81868797, 81865549, 83943913, Grooves: Double Groove, Mounts with 5/16" and 7/16" bolts, Includes: Back Housing, Mounting and Block Gasket, (Item #: 169000)$151.00
Decals and Emblems
No Picture
Decal Set - For 5600. Hood only. (Item #: 100703, Ref: R0522)$33.00
Ford Decal Set, 5600 1975-81, Vinyl - For Ford tractor model 5600, Ford 5600 diesel, Complete decal set less gear shift pattern, Made in the USA, (Item #: 102012)$86.41
Drive Train
Axle Shaft Seal - Seal and Retainer Assembly, outer, for Rear Axle Shaft. For tractor models 5000, 5600, 5610, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. (Item #: 113922, Ref: C5NN4969E)$17.90
Ball Bearing Assembly - The is an open, deep groove bearing. It has applications in transmissions as well and is CAR MFWD front ends. It measures: 60mm (2.362 inches) inside diameter, 110mm (4.33 inches) outside diameter, 22mm (0.866 inches) wide. Replaces manufacturer part numbers: 6212, 32306, ST269A, 3114946R91, K261879, 83930318, 20141040, CAR25813, 28996590, C5NN7127B, 81804781, 80996590, 20140, 253072272, 8101-06212, 1440545X1, 24101-62124, 971043 (Item #: 156046, Ref: C5NN7127B)$16.98
Counter Shaft - This Transmission Counter Shaft is used on Ford 5000, 5100, 5200, 7000, 7100, 7200, 5600, 6600, 7600, 6700, 7700, 5610, 6610, 7610. It has a 2.065 inside diameter. Replaces original part numbers C9NN7111B and C5NN7111G. (Item #: 134480, Ref: C9NN7111B)$162.00
Counter Shaft - Note that there is some discrepancy in OEM numbers on this part. This Counter Shaft has an inside diameter of 2.125 inches. Measure before ordering. If you have 2.065 inside diameter, then order part number C9NN7111B. It replaces C5NN7111G, C9NN7111B, D0NN7N047A, D2NN7111A, 81826590, 81878438, 81822960, 82930758, 82987564, 82983059, 83948780, 83960001, E6NN7111AA, E4NN7110AA (Item #: 172859, Ref: E6NN7111AA)$190.85
Gear, 1st and 5th - Used on 8 speed transmissions on Ford models 5000, 5100, 5190, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6600, 6610, 6610S, 6640, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7840, 8010, 8240, TS100, TS90. This gear has 46 and 28 teeth. It replaces OEM numbers 83946988, 82987560, E6NN7N100BA, E2NN7N100AA, 83959993, D2NN7N100A, 81826587 (Item #: 179401, Ref: E6NN7N100BA)$175.00
Gear, 2nd and 6th - Gear has 28 and 43 teeth. It is used is some 8 speed transmissions of Ford Tractors. Replaces OEM numbers C5NN7N101B, D2NN7N101A, 81813520, E2NN7N101AA, 81826588, C5NN7N101D, E6NN7N101BA, 82987561, 83959996, 83945994 (Item #: 179205, Ref: E6NN7N101B)$143.00
Gear, 3rd and 7th - This gear is used on 250C, 260C, 340B, 345D, 445A, 445D, 5000, 530B, 545A, 545D, 5600, 5610, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7610, 7710. It has 28 and 35 teeth and a 1.555 inch inside diameter. Replaces C9NN7N315B, CNN7N315B, E6NN7N315AA, E6NN7N315BA, 81822962. (Item #: 165995, Ref: C9NN7N315B)$119.00
Gear, 3rd and 7th - Gear has 35 Teeth. It is used on 8 Speed Non Synchro transmission. Replaces OEM part numbers 83960029, 81822962, 83959997, 82987562, C9NN7N315B, E6NN7N315AA, E6NN7N315BA (Item #: 165995, Ref: E6NN7N315BA)$119.00
Gear, Differential Side - Part 1 in the picture. For tractor models (2000, 3000, 4000 all 1965-1975 LH with diff. lock, LH or RH without locks), (5000, 7000 all 1965-1975 RH with Diff. lock, LH/RH without diff locks), (2600, 3600, 4100, 4600 all 1975-1981 LH with diff. lock, LH/RH without locks), (5600, 5700, 6600, 6700, 7600, 7700 all 1975-1981 RH with Diff. lock, LH/RH without locks), (2610, 3610, 4110 all 1981 and up LH with diff lock, LH/RH without locks), (5610, 6610, 6710, 7610, 7710 all 1981 and up RH with diff lock, LH/RH without locks). (Item #: 170394, Ref: C5NN4236A)$85.51
Gear Shift Boot - This Gear Shift Boot can be used on multiple Ford/New Holland Tractors built 1965 and later. The top holes is 5/8 inch and the bottom hole is 2 1/2 inches. It replaces original part numbers C5NN27534, C5NN275394, C5NN7277D, D4NN7N309A, 82007346. (Item #: 164365, Ref: C5NN27534)$3.50
Gear Shift Cover Gasket - This Gear Shift Gasket is used with C5NN7222 Gear Shift Assembly. Replaces 83958298, D2NN7223A, E0NN7223BA, 81829229, E5NN7223AA (Item #: 164338, Ref: E5NN7223AA)$3.20
Gear Shift Knob - This Gear Shift Knob fits 5/16 inch x 24 thread and approx. 1.299 inch diameter. It replaces original part numbers E440GB9, 81800669 (Item #: 121228, Ref: E440GB9)$4.10
Hi-Low Shift Lever - For Ford tractor models 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5900, 6410, 6600, 6610, 6810, 7000, 7100, 7200, 7600, 7610, 7810, Replaces Ford OEM number C7NN7210AB, 81818562, (Item #: 154971)$5.98
Hydraulic Pump Drive Gear - Hydraulic Pump Drive Gear is 1.125 inch overall thickness at the bushing. It is used with Housing C9NN7049C and E0NN7049AA. It will not work on C5NN7049A housing. Replaces: C7NN873A, C7NNN883A, D3NN873A, D9NNN883AA, D3NNN883A, D9NN883AA, D9NNN883AA, 83919059. (Item #: 172845, Ref: D3NNN883A)$94.00
Input Shaft - This Input Shaft is used on Step Up Step Down Transmissions. It is 9 inches in length. Used in the following tractors, 1965 and later: 2000, 3000, 2600, 3600, 4600, 4600SU, 5600, 6600, 7600, 3400, 3500. Replaces C5NN7015T. (Item #: 179307, Ref: C5NN7015T)$223.00
Input Shaft Seal - The measurements on the seal are 2.283 inch inside diameter, 3.130 inch outside diameter, 0.375 inch wide. This seal replaces OEM numbers: D9NN7048BA, D6NN7048B, D2NN7048A, 81826482, C5NN77047A, D9NN7048AA, 83924926, 83912260, 83924160. Used on Ford 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 8010, 8240, TS100, TS90 (Item #: 172928, Ref: D9NN7048BA)$6.20
Input Shaft, Transmission - For tractor models 5000, 5100, 5600, 6600, 6700, 7100, 7200, 7600, 7700. All without dual power. 19.125 inches long. 20 and 25 Splines. Replaces original part numbers C5NN7017A 81804582. (Item #: 119206, Ref: C5NN7017A)$92.00
Input Shaft Tube - This Input Shaft Tube is used on 5000, 5100, 5200, 7000, 7100, 7200, 5600, 6600, 7600 Ford Tractors. Replaces original part numbers C5NN7N541B, 81805278 (Item #: 154957, Ref: C5NN7N541B)$162.00
Main Shaft - 30/18 teeth. For tractor models (5000 with dual power 6/1973 and up), (5600, 6600, 6700, 5610, 6610, 6710, 6810 with dual power), 7810, 8010, 5610S, 6610S, 7610S, 7810S, (5640, 6640, 7740, 7840, 8240, TS90, TS100, TS110 with 8 speed less dual power, 16 speed with dual power). Replaces E7NN7C094AA. (Item #: 182728, Ref: 82983066)$378.00
Main Shaft - This Transmission Main Shaft has 30 teeth, 18/16 splines. It is 9.937 inches long. When replacing C9NN7C094B in units manufactured before 11/02/1971 it will also be necessary to replace C9NN7N315B. Replaces C9NN7C094B, C5NN7C094C. (Item #: 170132, Ref: C9NN7C094B)$264.00
Main Shaft - This Transmission Main Shaft is used with Dual Power and PTOs. It has 30 and 18 Teeth. Replace original part numbers E2NN7C094DA, E7NN7C094AA (Item #: 179391, Ref: E2NN7C094DA)$231.22
Main Shaft Rear Bearing - The measurements on this bearing are 55mm inside diameter, 100mm outside diameter, 21mm wide. It replaces OEM numbers C7NN7118B, DDN7025A, E1ADDN7025A. Used on Ford 5000, 5600, 6600, 6700. (Item #: 186548, Ref: C7NN7118B)$31.74
Output Shaft and Coupling Assembly - Used on 8 speed transmissions on the following (7000 With or without Dual Power), (5600, 6600, 6700 all 5/1984 and later without Dual Power), (5900 1981 - 7/1987 with Dual Power), (5610, 6610, 6710 6810, 7610, 7710 1981-7/1987 with Dual Power), 5640, 6640, 7740, 7840, 8240. Note that the non-splined end is 0.75 inches in diameter. Replaces Ford part numbers 81833752, 81822960, 81826590, 81878438, 82983059, D0NN7N071A, D2NN7N071A, D2NN7N071B, 83959995, E6NN7N71BA, E6NN7N071BA (Item #: 182884, Ref: E6NN7N071BA)$178.00
Output Shaft Gear - Gear has 28 and 49 Teeth. It is used an many Ford / New Holland Models with 8 speed and 6x4 Manual Reversing Transmissions. Replaces OEM part numbers C5NN7145A, 83960022, E6NN7145BA, 81804812, E6NN7145AA (Item #: 165990, Ref: E6NN7145AA)$358.00
Rear Axle to Center Housing O-Ring - This Rear Axle to Center Housing O-Ring is used on multiple Ford / New Holland Models. It is number 1 in the image. This O-Ring should always be replaced when changing brake disc on oil immersed systems. 13.50 inch inside diameter x .139 inches thick. Replaces 379313S91, 83417133, VPJ7202, 47P3852 (Item #: 113943, Ref: 379313S91)$6.40
Reverse Idler Shaft - Used on Ford / New Holland 4 and 6 cylinder models with 8 speed transmissions, this shaft is 3.5 inches long. Replaces OEM numbers C7NN7140C, 81817885 (Item #: 182891, Ref: C7NN7140C)$51.00
Secondary Countershaft - With a teeth count of 16-35-16, this Secondary Countershaft replaces Ford part numbers D9NN7B281CA, 81822961, C9NN7113B. It is used on Ford models: 345C, 345D, 445, 5000, 5100, 5110, 5190, 5200, 5340, 545, 545C, 545D, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 8010, 8240 (Item #: 166071, Ref: C9NN7113B)$135.00
Secondary Output Shaft Bearing - With measurements of 19mm inside diameter, 53.9mm outside diameter, and 15.9mm this bearing and cone assembly replaces Ford / New Holland part numbers D0NN7N047A, D2NN7111A, 81823619, 81823620, 81822960, 82930758, E6NN7061BA, E6NN7106AA, D0NN7N048A (Item #: 182935, Ref: D0NN7N047A)$41.00
Secondary Transmission Countershaft - This Gear has 16-34-16 teeth. It replaces Ford part numbers 81823634, D0NN7113C. This gear is used on Ford models 5000, 5100, 5200, 5340, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7610, 7700, 7710 (Item #: 180174, Ref: D0NN7113C)$424.00
Shift Fork - This is a 2nd and 6th Shift Fork. It replaces C5NN7231B, E8NN7231AA, 81804917, 81804928, 83974360 (Item #: 167826, Ref: E8NN7231AA)$58.00
Shift Knob - For tractor models Dexta, Super Dexta, (Major from 8/1958 up to 1964) 2100, 2600, 2610, 3000, 3100, 3120, 3400, 3600, 3610, 4000, 4110, 4140, 4400, 4410, 4500, 4600, 4610, 5000, 5110, 5200, 5600, 5610, 5640, 5900, 6410, 6600, 6610, 6810, 7100, 7200, 7600, 7610, 7740. 5/16 Inch - 24 UNF Thread. 81804882, 957E7213, NAA7209A Note, this part may arrive spherical as shown, or more flattened like BB7213A. This part is differentiated by 5/16 Inch - 24 UNF Thread. (Item #: 116912, Ref: C5NN7213A)$7.00
Transmission 3rd / 7th Gear - Part number D2NN7N315A is the third / seventh gear in 8 speed transmissions on Ford models: 5000, 5100, 5200, 5340, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7610, 7700, 7710. This gear has 34 teeth. Verify before ordering. Replaces D2NN7N315A, 81826596 (Item #: 182870, Ref: D2NN7N315A)$123.00
Transmission Countershaft Seal - This Transmission Countershaft Seal replaces original part number E62GE9. New Holland 81717077. It measures 2.885 inches x 1.649 inches x 0.625 inches. (Item #: 172981, Ref: E62GE9)$6.50
Transmission Filler Plug / Dipstick - This Transmission Filler Plug / Dipstick is used on Ford 5000, 5200, 5600, 5610, 5900, 6600, 6610, `6700, 6710, 7000, 7200, 7600, 7610, 7700, 7710; (1965-1993). Replaces 81817892, C7NN7N255A (Item #: 125398, Ref: C7NN7N255A)$22.50
Transmission Front Plate - This Transmission Front Plate replaces D2NN7N054A and D2NN7N054B. For models 5000, 7000, 5600, 6600, 7600, 5610, 6610, 7610, 8210. (Item #: 180326, Ref: D8NN7N054BA)$132.08
Transmission Front Plate Gasket - This gasket is used on 2000, 3000, 4000, 5000, 7000, 2600, 3600, 4600, 5600, 5700, 6600, 6700, 7600, 7700, 2610, 2910, 3610, 2910, 4610, 5610, 6610, 7610, 7710. Replaces E6NN7N057AA. (Item #: 179306, Ref: E6NN7N057AA)$6.80
Transmission Gasket Set - This Transmission Gasket Set is used on FORD 5000, 7000, 5600, 6600, 7600, 5610, 6610, 7610 all with 6 and 8 speed non-syncro transmission. (Item #: 169726, Ref: TG5000)$26.80
Transmission Mainshaft Front Bearing - Used in the transmissions of some of the following Ford models: 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 8010, 8240, this bearing has an inside diameter of 65mm, outside diameter of 100mm and is 18mm wide. This bearing has applications not list. It replaces OEM numbers; Ford / New Holland 81804635, C5NN7N046A, 5181866, Kubota 8101-06013. Landini SKF6013, 339673X1, Massey Ferguson 339673X1, Yanmar 24101-060134, Zetor 971014, 971019 (Item #: 182963, Ref: C5NN7N046A)$43.00
Transmission Oil Tube - Used on Ford 5600, 5700, 6600, 6700, 7600, 7700 tractors, this Transmission Lubrication Tube replaces Ford part numbers D8NN7N460BA, 83918315 (Item #: 179894, Ref: D8NN7N460BA)$59.00
Transmission Output Shaft Seal - Measures 39.4mm inside diameter x 60.3mm outside diameter x 12.7mm wide. It replaces C5NN77086A, 81808572, D66412, D40772, 363514R93, 70800166, ATY3988, ATY4067, AM848T, AP19243H, ATY4124, 1860325M1, 195506M1, 1077452M1 (Item #: 155727, Ref: C5NN77086A)$6.00
Transmission Rear Coupling - This a a paired set used on many Ford New Holland Models. Replaces OEM part numbers 83908698, 82983825, 83960027, E6NN7N072BA, D6NN7N072B (Item #: 167824, Ref: E6NN7N072BA)$78.00
Electrical System
No Picture
Alternator - Lucas Style (12089N) - For Ford tractor models 2310, 2600 (, N, R, V), 2610, 2810, 2910, 3600 (, N, NO, R, V), 3610, 3900, 3910 (, H, N, R), 4100, 4110, 4600, 4600SU, 4610, 4610SU, 5110, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, 9030, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 333, 334, 335, 420, 455, 515, 530A, 531, 532, 535, 550, 555, 555A, 555B, 655, 655A, Compatible with Ford Engine (s) BSD332, BSD333, BSD442, BSD444, BSD444T, Replaces Ford OEM number E3NN10B376AB, E3NN10B376AC, E3NN10B376AD, Replaces Lucas manufacturer number LRA00530, Lucas Style, Design: IR/EF, Voltage: 12, Rotation: Clockwise, Amperage: 45, Regulator: Internal, Pulley: Class V1, Single Groove, NOTE 1:Battery sense through external thermistor on vehicle. Do not apply full voltage (14V) to wire, will damage regulator. Need to use 1/4 watt 200 ohm resistor between S-terminal wire (orange) to B+ to test., (Item #: 189295)$115.00
Alternator - Lucas Style (12152) - For Ford tractor models 2600, 2610, 2810, 2910, 3600, 3610, 3900, 3910, 4100, 4110, 4600, 4610, 5600, 6600, 6610, 6700, 6710, 7600, 7700, 8600, 9600, Compatible with Ford Construction and industrial models 420, 515, Replaces Ford OEM number D6NN10B376A, Replaces Lucas manufacturer number 23814, Replaces manufacturer number 12152, 280-305, 11.201.067, 11.201.505, IA 0067, IA 0505, AAG1111, AAK1345, 23814A/D, 23814A/E, 24211, Lucas Style, Voltage: 12, Rotation: Clockwise, Amperage: 43, Regulator: Internal, (Item #: 112135)$156.00
Ignition Key Switch - 5 Position, 7 Terminal - For Ford tractor models TW10, TW30, 650, 2000 (3 Cyl), 2310, 2600, 2610, 2810, 2910, 3000, 3230, 3310, 3330, 3400, 3600, 3610, 3910, 3930, 4000 (3 Cyl), 4100, 4110, 4600, 4630, 5000, 5100, 5110, 5200, 5600, 5610, 5700, 5900, 6600, 6610, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8210, 8530, 8630, 8700, 8730, 8830, 9000, 9700, Compatible with Ford Construction and industrial models 515, 531, 535, 550, 3500, 4400, 4500 Replaces Ford OEM number 82849085, C5NN11N572A, C5NN11N501A, D5NN11N501A, E8NN11N501AA, E7NN11N501AB, E7NN11N501AC, 82849165, D5NN11572A, , Compatible with New Holland tractor models 3010S, 8010, Replaces New Holland OEM number 82849085, For gas and diesel with or without cold start, 5 Position 7 spade Switch, Threaded stem measures 3/4 - 27, (Item #: 124296)$13.40
Ignition Switch, Keyed - This 5 position, 7 terminal ignition switch comes with 2 key. Used on many tractor models (2000, 3000, 4000, 5000, 7000 1965-1975), 8000-9700, TW10, TW20, TW30, all 1968-1982. For 2600-7700 1975-1981. For 230A, 231, 233, 234, 333, 334, 335, 420, 515, 530A, 532, 535, all 1981-1990. For 7810-8210 1982-10/1985. For TW5-TW35 to 5/1983-2/1990. 8530-8830 3/1990 and up. Starter and Heat Ignition Switch for tractors with cold start. Not for Shibaura built tractors. Replaces OEM 82849085, 81871583, 81838692, 83999543, 83902803, E7NN11N501AB, D3NN11N501A, D5NN11N501A, C5NN11N501A, E7NN11N501AC, 83959710, 83976890, E7NN11N501AA, E8NN11N501AA (Item #: 116913, Ref: E7NN11N501AB)$10.00
Ignition Switch, Keyed - This three position Ignition Switch has 5 terminals. Gas or diesel without cold start.It is widely used on Ford / New Holland Tractors 1965 and later. Comes with 2 keys. Replaces C5NN11N572A, D3NN11N572A, 81806736, 81838693, 82849165. (Item #: 185146, Ref: D3NN11N572A)$19.00
Point Set - For Ford tractor models 2000, 2600, 3000, 3600, 4000, 4100, 4600, 5000, 5600, 6600, Replaces Ford OEM number C5AF12171C, 21A155, C5AF12171BVA, 1965 and up, (Item #: 111780)$6.60
Starter, Diesel Engines - With single contact solenoid, 12 volt, 10 tooth, CW rotation. For tractor models TW10, TW20, TW25, TW30, TW35 1979-1983 with 6-401, 2000, 3000 1965-1975, 2310 1982-1985, 3-158, 2610 1982-85, W 3-175, 2810 1983-89 with 3-158, 2910 1983-89 with 3-175, 3000 1965-68 with 3-175, 3230 1990-95 with 3-192, 3430 1990-98 with 3-192, 3610 1982-83 with 3-192, 3910 1983-90 with 3-192, 3930 1990-96 with 3-201, 4000 1965-72 with 3-192 or 3-201, 4100 1978-81 with 3-183, 4110 1977-83 with 3-201, 4630 1989-96 with 3-201, 1990-99 with 3-192 diesel, 5000 1965-76 with 4-256, 5030 1992-96 with 4-256, 5600 1975-81 with 4-256, 5610 1981992 with 4-256, 5900 1985-93 with 4-256, 6600 1975-81 with 4-256 diesel, 6610 1982-92 with 4-268, 6700 1975-81 with 4-256, 6710 1982-85 with 4-256, 7000, 7100, 7200 1971-75 with 4-256), 7400 1975-76 with 4-256, 7600, 7700 1975-81 with 4-256, 7710 1982-91 with 4-268, 7810 1978-91 with 6-401, 8000 1968-87 with 6-401, 8210 1978-91 with 6-401. Replaces 26395, 26211, 26339A, SLU003. (Item #: 100300, Ref: SLU0002)$160.00
Starter, Diesel, Gear Reduction - Gear Reduction Starters offer higher torque than a direct drive starter. This can be useful for diesel engines. This is a gear reduction replacement for our part SLU0002. Replaces 81833782, 81859494, C7NN11000C, D4NN11000A, D0NN11000A, D2NN11000A, 81859398, 81826488, D7NN11000A, D6NN11000A, D8NN11000CD, D8NN11000CB, D8NN11000CA, E2NN11000AA, D2NN11000B, D5NN11001A, D4NN11000B, D7NN11000B, D8NN11000DA29Z, D8NN11000CE, E3NN11000AA, D9NN11000AA, K262761, K308650, LRS212, 26395, 26211, 26339A (Item #: 181969, Ref: 80855520)$191.07
Starter Safety Switch - For tractor models 2000, 3000, 4000, 5000, 7000 all with 8 speed, dual range, 10-1966 and up. For 2100, 3100, 3400, 3500, 3550, 4400, 4500, 10-1966 and up with Manual Reversing Transmission. Ind: 231, 233, 335, 2600, 3600 all with 6 speed 1975 and up. Ind: 231, 233, 333, 335, 420, 515, 531, 532, 535, 2600, 3600, 340, 445, 540, 545, 4100, 4600, 4600SU all 8 speed 1975 and up. For 5600, 6600, 7600 with 7 and 8 speed 1975 and up. For 5700, 6700, 7700 with 7 and 8 speed 8-1976 and up. For 335, 2600, 3600, 340, 420, 515, 535, 445, 540, 545 all with Manual Reversing Transmission 1975 and up. For 5700, 6700, 7700, all clutch controls 8-1976 and up. For 8000, 9000, TW10, all clutch controls 1968 and up. For TW20, TW30, both clutch controls 1979 and up. Replaces C7NN7A247A, 81817901 (Item #: 115052, Ref: C7NN7A247A)$15.00
Starter Solenoid - Hitachi Style, 12 Volt, 3 Terminal Solenoid. It is used on many Ford / New Holland Tractors and Industrial models using Hitachi Starter numbers: S13-61, S13-61A, S12-62, S13-32, S13-32A, S13-73, S13-74, S1361, S1361A, S1262, S1332, S1332A, S1373, S1374. Replaces Ford / New Holland part numbers E2NN11390AA, SBA185816070, SBA185816200, SBA185846183. Replaces Hitachi Part Numbers 2114-67006, 2130-17004, 2130-8700, 2114-37003. Replaces Isuzu Part Numbers 8-94216-6330, 8-94218-7720. (Item #: 128269, Ref: E2NN11390AA)$27.60
Starter Solenoid - For 2000, 3000, 4000, 5000, 3900, 3910, 4100, 4600, 5600, 6600, 7700 With 5 inch starter (Item #: 105691, Ref: D7NN11390B)$38.00
Starter Solenoid, 12-Volt - Relay assembly, 12 volt, 4 terminal. Grounded through the base. For most 12 volt GAS models 1955 and later including: 601, 801, 801, 1100, 2000, 2150, 2300, 230A, 231, 2310, 233, 234, 2600, 2610, 2810, 2910, 3000, 3055, 3110, 3120, 3150, 3300, 3310, 333, 3330, 334, 335, 340, 3400, 3500, 360, 3610, 3900, 3910, 4110, 4140, 420, 4330, 4340, 4400, 4410, 445, 450, 4500, 4600, 4610, 5000, 5110, 515, 530, 531, 5340, 535, 540, 545, 550, 5600, 5610, 5700, 5900, 6410, 655, 6600, 6610, 6710, 6810, 7000, 7410, 7600, 7700, 7710. Replaces 311007FR. I terminal DOES ground through the base. (Item #: 105689, Ref: D2AF11450AA)$9.60
Voltage Instrument Stabilizer - For (2000, 3000, 4000, 5000, 7000, 1965-1975), (2600, 3600, 4100, 4600, 5600, 6600, 7600, 1976 to 1981). Voltage Stabilizer for instrument cluster replaces C5NN10N507A. (Item #: 125560, Ref: C7NN10N507A)$29.20
Voltage Regulator - This is a 12v, 14.4 volt set, A-circuit, with battery temp sensor. Fits alternators: E7NN10B376AB, E7NN10B376BB, E3NN10B376AD, 81863039, 81863039, 81868798. Fits on the back of Lucas/Marelli alternators. Replaces E8NN10316AA, 83981529 (Item #: 182960, Ref: E8NN10316AA)$34.00
Voltage Regulator - 12 Volt - For Ford tractor models 2310, 2600, 2610, 2810, 2910, 3600, 3610, 3900, 3910, 4100, 4110, 4600, 4600SU, 4610, 4610SU, 5110, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 333, 334, 335, 420, 515, 530A, 531, 532, 535, 550, 555, 555A, 555B, 655, 655A, Compatible with Ford Engine (s) BSD333, BSD442, BSD444, Replaces Ford OEM number D4NN10316A, 81846029, (Item #: 127002)$25.50
Voltage Regulator, 12 Volt - Voltage Regulators for Motorola Style Alternator, numbers D5NN10300E, D5NN10300D, D6NN10300A, D7NN10300B or D5NN10300D used on models 231, 2310, 233, 234, 2600, 2610, 340, 340A, 3600, 3900, 4100, 420, 445, 4600, 515, 531, 532, 535, 540, 540A, 545, 550, 555, 555A, 555B, 5600, 5700, 650, 655A, 6600, 6700, 755, 755A, 755B, 7700, 8700, 9700. All with diesel engines and an alternator. Replaces D1NN10316A, D1NN10316B, 21A656, D7NN10316B, D3NN10316A. (Item #: 119939, Ref: D1NN10316A)$36.00
No Picture
Wiring Harness - Rear wiring harness. For Ford tractor models: 5600, 6600, 7600, all with Alternator and Fuse Panel. (Item #: 184385, Ref: C9NN14N104B)$44.00
No Picture
Wiring Harness, Front - Front wiring harness for Ford Models: 5600, 6600, 7600, all with Alternator and Fuse Panel. Replaces OEM part numbers C5NN14A103AE and C7NN14A103M. (Item #: 117371, Ref: C9NN14A103C)$74.00
Engine Bearings
No Picture
Ball Bearing - Power Steer Gear Assembly - For Ford tractor models Dexta, Super Dexta, 2310, 2600, 2810, 2910, 3230, 3600, 3610, 3910, 3930, 4000, 4100, 4110, 4130, 4600, 4600SU, 4610, 4630, 4830, 5000, 5030, 5100, 5600, 5610, 6600, 6610, 6710, 7000, 7100, 7410, 7600, 7610, 7710, Compatible with Ford Construction and industrial models 234, 334, 532 Replaces Ford OEM number C9NN3647A, 119811ES, , Compatible with Massey Ferguson tractor models 35, 35X, 135, 148, 230, 240, 250, Replaces Massey Ferguson OEM number 3900187M1, 3711715M1, 354466X1, 2971X, Replaces New Holland OEM number 81822004, Size: 5/16", Material: Carbon Steel, (Item #: 168936)$0.50
Camshaft Bearing - Single Camshaft Bearing fits the following gas and diesel tractors 1965 and up: 2000, 3000, 2600, 3600, 4000, 4600, 5000, 5600, 5700, 6600, 6700, 7000, 7600, 7700, 7610, 7710, 8000, 8200, 8600, 8700, TW10, 9000, 9200, 9600, 9700. (Item #: 106297, Ref: C5NE6261B)$6.40
Connecting Rod Bearing - .020" Oversize - Journal - For Ford tractor models 4830, 5000, 5030, 5100, 5600, 5610, 5900, 6600, 6610, 6700, 6710, Compatible with Ford Construction and industrial models 555C, 555D, 650, 655, 655A, 655C, Compatible with Ford Engine (s) 233 (gas or diesel), 268 (gas or diesel), Replaces Ford OEM number 87790307, Sold per journal, Bearing Size: .020", For Standard connecting rod bearing use Item #: 106369, (Item #: 106367)$9.40
Connecting Rod Bearing - .030" Oversize - Journal - For Ford tractor models 4830, 5000, 5030, 5100, 5600, 5610, 5900, 6600, 6610, 6700, 6710, Compatible with Ford Construction and industrial models 555C, 555D, 650, 655, 655A, 655C, Compatible with Ford Engine (s) 233 (gas or diesel), 268 (gas or diesel), Replaces Ford OEM number 87790308, Sold per journal, Bearing Size: .030", For Standard connecting rod bearing use Item #: 106369, (Item #: 106368)$6.98
Connecting Rod Bearing - .040" Oversize - Journal - For Ford tractor models 4830, 5000, 5030, 5100, 5600, 5610, 5900, 6600, 6610, 6700, 6710, Compatible with Ford Construction and industrial models 555C, 555D, 650, 655, 655A, 655C, Compatible with Ford Engine (s) 233 (gas or diesel), 268 (gas or diesel), Replaces Ford OEM number 87790327, Sold per journal, Bearing Size: .040" Oversize, For Standard connecting rod bearing use Item #: 106368, (Item #: 106369)$11.60
Flywheel With Ring Gear - This Flywheel with Ring Gear is used with 13 inch clutches. It has 128 teeth. Used on engines: BSD332, BSD333, BSD444, BSD444T Replaces F1NN6375AA, 81871636 (Item #: 159169)$690.00
LuK® Permium Clutch Pilot Bearing - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6410, 6500, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7800, 7810, 7840, 7910, 8000, 8100, 8200, 8210, 8240, 8340, 8400, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9200, 9600, 9700, Compatible with New Holland tractor models TS90, TS100, TS110, Replaces OEM number F0NNN779AA, 83992560, C5NNN779B, For Standard Duty use Item #: 108005, (Item #: 169092)$28.80
Main Bearings - .020" Oversize - Set - For Ford tractor models Super Major, 4830, 5000 (1965-3/68), 5030, 5100, 5600 (1975-9/80), 5610 (1981-'93), 5900, 6600, 6610 (1981-93), 6710, 7000, 7100, 7200, 7400, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models A62, 555C, 555D, 575D, 650, 655, 655A, 655C, 750, 755, 755A, 755B, Compatible with Ford Engine (s) 268, 268T, Replaces Ford OEM number 87790359, 87790492, Sold in complete set, Bearing Size: .020", Full groove upper with slot and small oil hole, For Standard main bearing use Item #: 106418, (Item #: 106416)$65.00
Main Bearings - .030" Oversize - Set - For Ford tractor models Super Major, 4830, 5000 (1965-3/68), 5030, 5100, 5600 (1975-9/80), 5610 (1981-'93), 5900, 6600, 6610 (1981-93), 6710, 7000, 7100, 7200, 7400, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models A62, 555C, 555D, 575D, 650, 655, 655A, 655C, 750, 755, 755A, 755B, Compatible with Ford Engine (s) 268, 268T, Replaces Ford OEM number 87790360, 87790493, Sold in complete set, Bearing Size: .030", Full groove upper with slot and small oil hole, For Standard main bearing use Item #: 106418, (Item #: 106417)$101.00
Main Bearing Set, .010 - Replaces 4-CFPN6333D and 1-EBPN6337D. For 5000, 5600, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. (Item #: 106415, Ref: MBK634-010)$75.00
Main Bearing Set, .020 - Replaces 4-CFPN6333E and 1-EBPN6337E. For 5000, 5600, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. (Item #: MBK634-020)$98.31
Main Bearing Set, .030 - Replaces 4-CFPN6333F and 1-EBPN6337F. For tractor models 5000, 5600, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. (Item #: MBK634-030)$94.36
Main Bearing Set, Std - Main Bearing Set. For tractor models: 5000, 5600, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. Replaces 4-CFPN6333B and 1-EBPN6337B. (Item #: 106414, Ref: MBK634)$101.00
No Picture
PTO Drive Clutch Piston - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600 (& C, O), 6610 (& O, S), 6640 (& O), 6700, 6710, 6810 (& S), 7000, 7100, 7200, 7410, 7600 (& C), 7610 (& O, S), 7700, 7710, 7740 (& O), 7810 (& O, S), 7840 (& O), 7910, 8000, 8200, 8210, 8240, 8340, 8530, 8600, 8630, 8670 (& A), 8700, 8730, 8770 (& A), 8830, 8870 (& A), 8970 (& A), 9000, 9030 (& E, V), 9200, 9600, 9700, Compatible with Ford Construction and industrial models 8400 Replaces Ford OEM number F1NNN786AA, D3NNN786A, C5NNN786C, C9NNN786A, , Compatible with New Holland tractor models TB80, TB85, TB90, TB100, TB110, TB120, TS90, TS100, TS110, TS115, TV140, TV145, TV6070, 7010, 8010, (Item #: 176508)$23.40
PTO Drive Shaft Bushing - Front - For Ford tractor models 5000, 5100, 5200, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7810S, 7840, Replaces Ford OEM number C5NN798A, Inside Diameter: 1.131", Length: .94", (Item #: 165270)$6.00
Rod Bearing, .010 - SINGLE Rod Bearing (.010 size) for the following 3-Cylinder Gas or Diesel Engines: 158, 175, 192, 201 and the following 4-Cylinder Diesel Engines: 233, 256 and the 401 6-Cylinder Diesel Engine. (you must order 1 bearing per cylinder for complete engine). For 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710, 8000, 8200, 8600, 8700, TW10. (Item #: 106375, Ref: DFPN6211D)$9.20
Rod Bearing, .020 - SINGLE Rod Bearing (.020 size) for the following 3-Cylinder Gas or Diesel Engines: 158, 175, 192, 201 and the following 4-Cylinder Diesel Engines: 233, 256 and the 401 6-Cylinder Diesel Engine. (you must order 1 bearing per cylinder for complete engine). For 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710, 8000, 8200, 8600, 8700, TW10. (Item #: 106376, Ref: DFPN6211E)$9.90
Rod Bearing, .030 - SINGLE Rod Bearing (.030 size) for the following 3-Cylinder Gas or Diesel Engines: 158, 175, 192, 201 and the following 4-Cylinder Diesel Engines: 233, 256 and the 401 6-Cylinder Diesel Engine. (you must order 1 bearing per cylinder for complete engine). For 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710, 8000, 8200, 8600, 8700, TW10. (Item #: 106377, Ref: DFPN6211F)$11.10
Rod Bearing, Standard - SINGLE Rod Bearing (standard size) for the following 3-Cylinder Gas or Diesel Engines: 158, 175, 192, 201 and the following 4-Cylinder Diesel Engines: 233, 256 and the 401 6-Cylinder Diesel Engine. (you must order 1 bearing per cylinder for complete engine). For 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710, 8000, 8200, 8600, 8700, TW10. (Item #: 106374, Ref: DFPN6211B)$9.00
No Picture
Thrust Washer - For Ford tractor models Major, Super Major, 2000, 2100, 2110, 2120, 2150, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3600, 3610, 3900, 3910, 4000, 4100, 4110, 4190, 4200, 4330, 4340, 4410, 4600, 4600SU, 4610, 5000, 5110, 5600, 5610, 5640, 5700, 5900, 6000, 6610, 6640, 6700, 6710, 6810, 7000, 7410, 7600, 7610, 7700, 7710, 7740, 7810, 7840, 7910, 8210, 8340, Compatible with Ford Construction and industrial models 3500, 3550, 4500, Replaces Ford OEM number 508E4230A, (Item #: 174131)$4.10
Engine Gaskets
Block to Rear Engine Plate Gasket - Block to Rear Engine Plate. Fits Ford tractors 1965 and later, gas and diesel. Replaces original part numbers C7NN6N008B, 81820964, C7NN6N008A, VPC5310, 1820964. (Item #: 123602, Ref: C7NN6N008B)$6.70
Gasket Set, Complete - For 233 CID DIESEL engine in: 5000 (1965 to 3/1968), (5600 and 5700, 1975 to 9/1980) . Contains upper and lower sets, and head gasket. (Item #: 184523, Ref: FS5000)$125.00
Gasket Set, Complete - For 256 GAS/DIESEL or 268 CID DIESEL engines in: 5000 (4/1968 to 1975), 5600, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. Contains upper and lower sets, and head gasket. (Item #: 184549, Ref: FS5670)$160.00
Upper Gasket Set - For 233 CID DIESEL 4.2 Inch BORE engine in: (5000, 1965 to 3/1968), 5600, 5700. Includes head gasket. (Item #: 106328, Ref: HS5000)$35.90
Upper Gasket Set, Less Head gasket - For 233/268 DIESEL or 256 GAS/DIESEL engines in: 5000, 5600, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. Does NOT include Head Gasket. (Item #: 172690, Ref: CFPN6008C)$20.80
Basic Engine Overhaul Kit, 256 Diesel - 256 CID 4 cylinder diesel 4.4 inch standard bore. Basic Engine Kit less rod and main bearings with standard pistons D4NN6108AA, rings, pin bushings, complete gasket kit. Order bearings separately. For 5000 (4/1968-1975), 5600 (10/1980-1981), 5700 (10/1980-1981), 6600 (1975-9/1980), 6700 (1975-9/1980). (Item #: 130787, Ref: BEKF2560D-LCB)$527.00
Basic In-Frame Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic in-frame kit with standard pistons, rings, valve grind gasket kit, oil pan gasket. For 5000 (1965-3/1968), 5600 (1975-9/1980), 5700 (1975-9/1980). (Item #: 184777, Ref: BIFF2330D)$354.00
Basic In-Frame Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic in-frame kit with .020 inch oversize pistons, rings, valve grind gasket kit, oil pan gasket. For 5000 (1965-3/1968), 5600 (1975-9/1980), 5700 (1975-9/1980). (Item #: BIFF2332D)$447.67
Basic In-Frame Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic in-frame kit with .030 inch oversize pistons, rings, valve grind gasket kit, oil pan gasket. For 5000 (1965-3/1968, 5600 (1975-9/1980), 5700 (1975-9/1980). (Item #: 189575, Ref: BIFF2333D)$280.00
Basic In-Frame Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic in-frame kit with .040 inch oversize pistons, rings, valve grind gasket kit, oil pan gasket. For 5000 (1965-3/1968), 5600 (1975-9/1980), 5700 (1975-9/1980). (Item #: BIFF2334D)$447.66
Basic In-Frame Overhaul Kit, 256 Diesel - 256 CID 4 cylinder diesel 4.4 inch standard bore. Basic in-frame kit with standard pistons, rings, valve grind gasket kit, oil pan gasket. For 5000 (4/1968-1975), 5600 10/1980-1981), 5700 10/1980-1981), 6600 (1975-9/1980), 6700 (1975-9/1980). (Item #: 184778, Ref: BIFF2560D)$323.00
Basic In-Frame Overhaul Kit, 256 Diesel - 256 CID 4 cylinder diesel 4.4 inch standard bore. Basic in-frame kit with .020 inch oversize pistons, rings, valve grind gasket kit, oil pan gasket. For 5000 (4/1968-1975), 5600 10/1980-1981), 5700 10/1980-1981), 6600 (1975-9/1980), 6700 (1975-9/1980). (Item #: 189651, Ref: BIFF2562D)$314.00
Basic In-Frame Overhaul Kit, 256 Diesel - 256 CID 4 cylinder diesel 4.4 inch standard bore. Basic in-frame kit with .030 inch oversize pistons, rings, valve grind gasket kit, oil pan gasket. For 5000 (4/1968-1975), 5600 10/1980-1981), 5700 10/1980-1981), 6600 (1975-9/1980), 6700 (1975-9/1980). (Item #: 189576, Ref: BIFF2563D)$318.00
Basic Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic Engine Kit. Contains standard pistons, rings, pin bushings, complete gasket kit. Order bearings separately. For 5000 (1965-3/1968), 5600 (1975-9/1980), 5700 (1975-9/1980). (Item #: 130777, Ref: BEKF2330D-LCB)$349.00
Basic Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic Engine Kit. Contains .020 inch pistons, rings, pin bushings, complete gasket kit. Order bearings separately. For 5000 (1965-3/1968), 5600 (1975-9/1980), 5700 (1975-9/1980). (Item #: 131032, Ref: BEKF2332D-LCB)$338.00
Basic Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic Engine Kit, contains .030 inch pistons, rings, pin bushings, complete gasket kit. Order bearings separately. For 5000 (1965-3/1968), 5600 (1975-9/1980), 5700 (1975-9/1980). (Item #: 131033, Ref: BEKF2333D-LCB)$349.00
Basic Overhaul Kit, 233 Diesel - 233 CID 4 cylinder diesel 4.2 inch standard bore. Basic Engine Kit, contains .040 inch pistons, rings, pin bushings, complete gasket kit. Order bearings separately. For 5000, 5600, 5700. (Item #: 131034, Ref: BEKF2334D-LCB)$338.00
Basic Overhaul Kit, 256 Diesel - 256 CID 4 cylinder diesel 4.4 inch standard bore. Basic Engine Kit, less rod and main bearings with .020 inch oversize pistons D4NN7108AC, rings, pin bushings, complete gasket kit. Order bearings separately. For 5000 (4/1968-1975), 5600 (10/1980-1981), 5700 (10/1980-1981), 6600 (1975-9/1980), 6700 (1975-9/1980). (Item #: 131035, Ref: BEKF2562D-LCB)$373.00
Basic Overhaul Kit, 256 Diesel - 256 CID 4 cylinder diesel 4.4 inch standard bore. Basic Engine Kit, less rod and main bearings with .030 inch oversize pistons D4NN6108AD, rings, pin bushings, complete gasket kit. Order bearings separately. For 5000 (4/1968-1975), 5600 (10/1980-1981), 5700 (10/1980-1981), 6600 (1975-9/1980), 6700 (1975-9/1980). (Item #: 131036, Ref: BEKF2563D-LCB)$384.00
Engine Overhaul Kit with Crankshaft - Used on 233 CID Four Cylinder Diesel Engine. 4.2 inch standard bore. This kit includes: Pistons, Pins, Rings, Retainers, overhaul gaskets set with crankshaft seals, new crankshaft, rod bearings and main bearings. This is a non-sleeved engine. If you need to sleeve your engine back to standard, sleeves are available as part number C5NN6055A. The crankshaft in this kit has a 1/2 inch wide balancer gear with 78 Teeth, 4.20 inch stroke. The piston height in this kit is 5.079 inches. This engine was originally used on 5000 (1965-68), 5600 (1975-80), 5700 (1975-80) (Item #: 183942, Ref: EKMC30)$1969.01
Engine Overhaul Kit with Crankshaft - Used on 256 CID Four Cylinder Diesel Engine. 4.4 inch standard bore. This kit includes: Pistons, Pins, Rings, Retainers, overhaul gaskets set with crankshaft seals, new crankshaft, rod bearings and main bearings. This is a non-sleeved engine. If you need to sleeve your engine back to standard, sleeves are available as part number D7NN6055A. The crankshaft in this kit has a 1/2 inch wide balancer gear with 78 Teeth, 4.20 inch stroke. The piston height in this kit is 5.079 inches. This engine was originally used on 5000 - 1968 and later, 5600 10/1980 and later, 5610 to 7/1987, 6600, 6700 to 9/1980. This kit will also work for later 5610 tractors but the pistons are not Humped Base Bowl Pistons and are replaced by earlier style pistons. (Item #: 183944, Ref: EKMC31)$1942.07
Engine Rebuild Kit - Less Bearings - .040" Oversize Pistons, BSD442, 256 - For Ford tractor models 5000 (4/68-12/74), 5100 (4/68-12/74), 5190 (4/68-12/74), 5200 (4/68-12/74), 5340 (4/68-12/74), 5600 (10/80-12/81), 5610 (1/81-7/87), 5900 (5/85-7/87), 6500 (3/73-10/75), 6600 (1/75-9/80), 6700 (1/75-9/80), Compatible with Ford Construction and industrial models 650 (11/75-12/77), 655 (7/85-7/87), 655A (6/85-7/87), 5500 (6/68-12/69), 5550 (1/70-12/73), Compatible with Ford Engine (s) BSD442, 256, Compatible with New Holland Hay Cutting (s) 907, 909, 910, 912, 1100, 1112, 1114, 1495, Standard Bore: 4.4007", Stroke: 4.203", Naturally aspirated, Models 4/68-7/87, 1.500" piston pin, Dished bowl, Rectangular top ring, Early rod, Kit includes: .040" Oversize Pistons, Piston Ring Set, Connecting Rod Bushings, and Gasket set with Crank Seals, Kit does not include connecting rod or main bearings, For standard connecting rod bearing use Item #: 106417, (Item #: 131037)$384.00
Engine Rebuild Kit with Valve Train - Less Bearings, BSD439, 233 - For Ford tractor models 5000 (1/65-3/68), 5100 (1/65-3/68), 5190 (1/65-3/68), 5200 (1/67-3/68), 5600 (1/75-9/80), 5700 (7/78-9/80), Compatible with Ford Construction and industrial models 5500 (1/67-5/68), Compatible with Ford Engine (s) BSD439, 233, Bore: 4.2007", Stroke: 4.203", Models 1/65-9/80, Kit includes: Pistons, Piston Ring Set, Connecting Rod Bushings, Gasket set with Crank Seals, and Valve Train Set, Kit does not include connecting rod or main bearings, For standard connecting rod bearing use Item #: 106417, (Item #: 130803)$207.98
Engine Rebuild Kit with Valve Train - Less Bearings, BSD442, 256 - For Ford tractor models 5000 (4/68-12/74), 5100 (4/68-12/74), 5190 (4/68-12/74), 5200 (4/68-12/74), 5340 (4/68-12/74), 5600 (10/80-12/81), 5610 (1/81-7/87), 5900 (5/85-7/87), 6500 (3/73-10/75), 6600 (1/75-9/80), 6700 (1/75-9/80), Compatible with Ford Construction and industrial models 650 (11/75-12/77), 655 (7/85-7/87), 655A (6/85-7/87), 5500 (6/68-12/69), 5550 (1/70-12/73), Compatible with Ford Engine (s) BSD442, 256, Compatible with New Holland Hay Cutting (s) 907, 909, 910, 912, 1100, 1112, 1114, 1495, Bore: 4.4007", Stroke: 4.203", Naturally aspirated, Models 4/68-7/87, 1.500" piston pin, Dished bowl, Rectangular top ring, Early rod, Kit includes: Pistons, Piston Ring Set, Connecting Rod Bushings, Gasket set with Crank Seals, and Valve Train Set, Kit does not include connecting rod or main bearings, For standard connecting rod bearing use Item #: 106417, (Item #: 130824)$463.00
No Picture
In Frame Engine Overhaul Kit - For 5600, 5700 all 1975-9/1980, 233 CID Diesel, 4 cylinder, 4.2 inch bore. In Frame Engine Overhaul Kit includes Piston Liner kit, Connecting Rod Bearing kit, and Overhaul Gasket set. When ordering, specify in comments section Piston Size of Standard, .020, .030 or .040, Bearing size of Standard, .010, .020, .030 or .040. (Item #: IK196)$633.10
No Picture
In Frame Engine Overhaul Kit - For (5600, 5700 all 10/1980-1981), (6600, 6700 all 1975 to 9/1980) all with 256 CID Diesel, 4 cylinder 4.4 inch bore. In frame engine overhaul kit includes piston liner kit, connecting rod bearing kit and overhaul gasket set. When ordering, specify in comments section piston size of standard, .020 inch, .030 inch or .040 inch. Bearing size of Standard, .010 inch, .020 inch, .030 inch or .040 inch. (Item #: IK197)$457.79
Piston and Rings - .040" Oversize - For Ford tractor models 650, 5000, 5100, 5190, 5200, 5340, 5550, 5600, 5610, 5900, 6500, 6600, 6700, Compatible with Ford Engine (s) BSD442, 256 Replaces Ford OEM number D4NN6108A-40, , Compatible with New Holland Hay Cutting (s) 907, 909, 910, 912, 1100, 1112, 1114, 1495, Naturally Aspirated, Bore: 4.4007", Stroke: 4.203", (Item #: 166078)$88.00
Piston and Rings - .040" Oversize - For Ford tractor models 2610, 2910, 3000, 3100, 3300, 3310, 3330, 3600, 5000 (1965-3/'68), 5600 (1975-9/'80), Compatible with Ford Construction and industrial models 335, 340, 340A, 340B, 420, 445, Compatible with Ford Engine (s) BSD329, BSD439, 175, 233, Replaces Ford OEM number D6NN6108L-40, Standard Bore: 4.2007", Includes: .040" Oversize Piston, Rings, Pin and Retainers, For standard use Item #: 128696, (Item #: 166088)$98.00
Piston and Rings - Standard - Single Cylinder - For Ford tractor models 3230, 3430, 3610, 3910, 4830, 5000 (4/'68-1975), 5030, 5100, 5600 (10/'80-1981), 5610, 5900, 6600 (1975-9/'80), 6700, Compatible with Ford Construction and industrial models 345C, 445C, 455, 555C, 555D, 650, 655, 655A, Compatible with Ford Engine (s) BSD332, BSD442, 192, 256, Replaces Ford OEM number F2NN6K100EA, Replaces OEM number HCD4NN6108A, Compression height of piston: 2.779", Standard Bore: 4.401", Pin and retainers included, (Item #: 128695)$100.00
No Picture
Rebore Kit - Re-bore sleeve and piston kit. For 5000, 5600, 5700, 6600, 6700. Contains Pistons, sleeves, rings, pins and pin retainers. (Item #: RBK679)$956.52
Rebore Kit - 0.030 - For Ford tractor models 650, 5000, 5100, 5190, 5200, 5340, 5550, 5600, 5610, 5900, 6500, 6600 Replaces Ford OEM number D4NN6108A-30, , Compatible with New Holland Hay Cutting (s) 907, 909, 910, 912, 1100, 1112, 1114, 1495, Replaces New Holland OEM number D4NN6108A-30, (Item #: 167126)$66.00
Engine Parts
Balancer Gear - Left Hand - For Ford tractor models 4830, 5000, 5030, 5100, 5110, 5600, 5610, 5700, 5900, 6410, 6600, 6700, 6810, 7000, 7600, 7610, 7700, 7710, Replaces Ford OEM number 81874001, Fits Left Hand Side, 15.4 MM Wide, (Item #: 162574)$168.00
Balancer Gear - Right Hand - For Ford tractor models 4830, 5000, 5030, 5100, 5110, 5600, 5610, 5700, 5900, 6410, 6600, 6700, 6810, 7000, 7600, 7610, 7700, 7710, Replaces Ford OEM number 81873999, Fits Right Hand Side, 15.4 MM Wide, (Item #: 162573)$156.00
Ball Type Governor with Umbrella - For the following Ford models made after 1965: 2000 (3 cylinder), 2600, 3000, 3600, 4000 (3 cylinder), 4600, 5000, 5600. Replaces 377509-S, 500901, 81806923, 81817221, 83417081, C5NE12471A, and C5NE12B462A. (Item #: 183844, Ref: C7NN12471A)$179.00
Camshaft - For 4-cylinder gas or diesel engine in tractors 5000 (1965 to 1975); 5600, 5700, 6600, 6700, 7600, 7700, (1975 to 1981); 5610, 5900, 6610, 6710, 7710, (1981 to 1991). Industrial: 650, 6500, 750, 755, 755A, 7500, (1972 to 7-1987); 755B, (8-1987 to -); 655, 655A, (6-1985 to 10-1988). With 3/16 inch Keyway. Replaces C7NN6250B, E1TN6250AA, E6NN6250AA. (Item #: 150911, Ref: 87800353)$113.00
Camshaft Gear - This camshaft gear is for Models 2310, 2810 and 2910 all with 158 CID Diesel (BDS326), model 2610 with 175 CID Diesel (BSD329), models 3610 and 3910 both with 192 CID Diesel (BSD329), models 4000, 4110, 4600 and 4610 all with 201 CID Diesel (BSD333), models 5600 and 5700 with 233 CID Diesel (BSD439), models 4830, 5030, 5110, 5610, 5900, 6600 and 6700 all with 256 CID Diesel (BSD442), and model 7600 with 256 CID Turbo Diesel (BSD442T). Replaces E3NN6N251AB, 83963173 (Item #: 191987, Ref: E3NN6N251AB)$316.00
Camshaft Plug - Used on Ford engines: 158, 175, 192, 201, 233, 256, 268, 401 this camshaft plug replaces part numbers C5NND851B, 83994133, C5NND851A, 1816594 (Item #: 166919, Ref: C5NND851B)$42.90
Clutch Disc - For Ford tractor models TW10, TW20, TW30, 5110, 5600, 5610, 5640, 5700, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7410, 7610, 7710, 7740, 7810, 7840, 7910, 8000, 8200, 8210, 8600, 8700, 9000, 9200, 9600, 9700 Replaces Ford OEM number C0NN7B442A, , Compatible with New Holland tractor models TS80, TS90, TS100, TS110, 7010, 8010, Replaces New Holland OEM number 81805123, (Item #: 155502)$18.60
Clutch Disc - For Ford tractor models 5000, 5100, 5190, 5200, 5340, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7700, 8000, 8200, 8700, 9000, 9200, 9600, 9700, Compatible with Ford Construction and industrial models 8400, Replaces Ford OEM number D2NN7R000A, C9NN7R000A, 6.820" Major / 6.640" Minor Inner Diameter, 9.005" Outer Diameter, 0.082" Width, 80 Teeth, (Item #: 155517)$79.00
Clutch Disc - For Ford tractor models TW10, TW20, TW30, 5110, 5600, 5610, 5640, 5700, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, 7740, 7810, 7840, 7910, 8000, 8200, 8210, 8600, 8700, 9000, 9200, 9600, 9700 Replaces Ford OEM number E0NN7Z031AA, , Compatible with New Holland tractor models TS80, TS90, TS100, TS110, TS120, 7010, 8010, Replaces New Holland OEM number 83925696, (Item #: 155540)$11.90
Connecting Rod - This new Connecting Rod used a 1.50 inch piston pin. It is used on Ford diesel engines: 192, 201, 233, 256, 268, 401 and Ford gas engines: 192, 201, 233, 256. It replaces OEM part numbers C7NN6205. Casting numbers: C7NN6205A, E5NN6205AA, E1TN6205AD. VERIFY CASTING NUMBERS BEFORE ORDERING. (Item #: 128642, Ref: C7NN6205)$96.00
Connecting Rod Assembly (36mm Journal) - New. Replaces C7NN6200A, E3HN6200AC, E4NN6200AB, E9NN6200AB, E9NN6200CA, F9NN6200AB, 81864279, 81875622, E3HN6200AC42, F2NN6200BA (*NOTE: Replace the complete set when replacing C5NE6200A Gas 1965-3/1968).C7NN6200A (Item #: 128642, Ref: C7NN6205)$96.00
Connecting Rod Bolt - These Connecting Rod Bolts are for gas and diesel Models: 1965 and later: 2000, 3000, 4000, 5000, 7000, 8000, 9000, 2600, 3600, 4100, 4600, 5600, 5700, 6600, 6700, 7600, 7700, 8600, 8700, 9600, 9700, 2610, 3610, 4110, 4610, 5610, 6610, 6710, 7610, 7710, TW5, TW10, TW15, TW20, TW25, TW30, TW35. Replaces C5NE6214A, E4TN6214AB, E8NN6214AA, E9NN6214BA. 3 1/4 inches long, 7/16 diameter. Priced each. Uses 385279S2 nut, not included. (Item #: 114721, Ref: E4TN6214AA)$3.70
Connecting Rod, Used - For Ford tractor models Super Major, TW5, TW10, 3230, 3430, 3610, 3910, 3930, 4000 (1965-1975), 4110, 4120, 4130, 4140, 4330, 4340, 4600, 4610, 4630, 4830, 5000 (1965-1975), 5030, 5100, 5600 (1975-1981), 5610, 5900, 6600 (1975-1981), 6610, 6700, 6710, 7810, 7910, 8000, 8210, 8530, 8600, 8700, Compatible with Ford Construction and industrial models A64, 345, 445, 455, 515, 535, 540, 545, 545D, 550, 555, 655, Replaces Ford OEM number C7NN6205A, C7NN6205, E5NN6205AA, E1TN6205AD, Solid non-drilled Beam, ID Pin Bushing: 1.500", For a new version of this item use Item #: 128642, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435947)$40.01
Crankshaft - 4 cylinder, 4.2 inch stroke, 12.5 mm 78 tooth Balancer Gear. Uses 36 mm wide Rod Bearings. NOTE: Measure Balancer Drive Gear before ordering. Do not mix sizes. Used on 5000, 5100, 5190, 5200, 5600, 5610, 5700, 6000, 6500, 6600, 6610, 6700, 6710, 7000, 7100, 7200, 7600, 7610, 7700, 7710, Fits Ford Construction and Industrial (s) A62, 650, 655, 750, 5500, 5550, 7500. Replaces 81804029, C5NE6303K, F0NN6300FB (Item #: 100552, Ref: C5NE6303K)$847.74
Crankshaft - 76 Tooth Gear - Late - For Ford tractor models Super Major, 5000, 5100, 5190, 5200, 5600, 5610, 5700, 6000, 6500, 6600, 6610, 6700, 6710, 7000, 7100, 7200, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models A62, 650, 655, 750, 5500, 5550, 7500, Compatible with Ford Engine (s) BSD442, 256, Replaces Ford OEM number 81804029, C5NE6303K, F0NN6300FB, Replaces Casting number 6110A, Engine: 256 CID - 4.2 Stroke, 4 Cylinder, Flange: Centering Ring, 6 Bolt Holes, 1 Dowel Hole, Balance Drive Gear: 76 Tooth Right Hand Helix, 15MM Wide - Installed, Snout: 1 Bolt Hole, 1 Keyway, Verify gear tooth count before ordering, Additional Handling and Oversize Fees Apply To This Item, (Item #: 100553)$428.58
Crankshaft Balancer Assembly - For Ford tractor models 4830, 5030, 5110, 5600, 5610, 5900, 6500, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models 550, 555, 555A, 555B, 555C, 555D, 575D, 650, 655A, 655C, 655D, 675D, 750, 755A, 755B, 7500, Replaces Ford OEM number F1NN6A311AA, E5NN6A311AA, 81873989, E3NN6A311AA, Teeth: 39, 5/8" wide gears, (Item #: 169723)$492.80
Crankshaft Pulley - Used on Ford / New equipment built 1965 and later. This is a single groove pulley. This pulley is not for Shibaura built compacts. Replaces D5NN6A312A, 83903583 (Item #: 154921, Ref: D5NN6A312A)$139.00
Crankshaft Pulley Spacer - Used on many Ford / New Holland models, 1965 and later, this is a keyed spacer. It fits behind the crankshaft pulley. Replaces OEM part numbers 83995427, 1811427, 81811427, C5NE6B306A, C5NE6C306A (Item #: 154924, Ref: C5NE6B306A)$20.40
No Picture
Crankshaft Pulley, Used - For Ford tractor models 2000, 2100, 2110, 2120, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3120, 3190, 3230, 3300, 3310, 3330, 3400, 3430, 3500, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4140, 4190, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 5190, 5200, 5340, 5550, 5600, 5610, 5700, 5900, 6410, 6500, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models 230A, 231, 234, 250C, 260C, 333, 334, 335, 340, 340A, 340B, 345C, 345D, 420, 445A, 445C, 445D, 450, 455, 455C, 455D, 515, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 575D, 650, 655, 655A, 655C, 655D, 675D, 750, 755, 755A, 755B, 3500, 3550, 4140, 4400, 4500, 5500, 5550, 6500, 7500 Replaces Ford OEM number D5NN6A312A, 83903583, , Compatible with New Holland tractor models TB80, TB85, TB90, TB100, TB110, TB120, Compatible with New Holland Skid Steer Loader(s) L783, L785, Compatible with New Holland Hay Cutting(s) 1118, 1499, Replaces New Holland OEM nos D5NN6A312A, For a new version of this item use Item #: 154921, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 443383)$81.00
No Picture
Crankshaft, Remanufactured, E5NN6303EA - For Ford tractor models 5000 (with 233 engine), 5600, 5610, 6600, 6700, 7000, 7600, 7700, Replaces Casting number E5NN6303EA, E5NN6303GA, Engine: 256 after 9/4/86 with 4.2" stroke, Teeth: 76 helical cut left to right if looking from rear, Our remanufactured crankshafts are cleaned, magnafluxed, measured and reground if necessary, the journals are then polished., (Item #: 203838)$580.01
No Picture
Crankshaft, Remanufactured, F1NN6300BD - For Ford tractor models 5110, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, 9030, Compatible with Ford Construction and industrial models 555C, 555D, 575D, 650, 655C, 655D, 675D, 750, 755, 755A, 755B, 7500, Compatible with Ford Engine (s) BSD442, BSD444 Replaces Ford Casting number F1NN6300BD, , Compatible with New Holland Hay Cutting (s) 1118, Replaces OEM number 81873979, 4.4" Stroke, Left Hand Helical Cut Gear, (Item #: 209964)$810.01
Crankshaft Repair Kit - Speedi Sleeve Crankshaft Repair Kit will sleeve the end of the crankshaft that has a wear groove worn by the crankshaft seal. Ultra thin sleeve slides over damaged crank. Allows the use of standard seal E5NN6701BA. For 2000, 2600, 2610, 2810, 2910, 3000, 3110, 3600, 3610, 3910, 4000, 4110, 4600, 4610, 5000, 5600, 5610, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. (Item #: 106355, Ref: 99472)$173.00
Cylinder Head Overhaul Kit - Engine Kit, Valve Overhaul. For 5600, 5700, 6600 (Item #: 120296, Ref: VOKF256)$114.00
No Picture
Cylinder Head, Remanufactured, C0NN6090C - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 6710, 7000, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) 256 (Diesel), 268 (Diesel), Replaces Ford Casting number C0NN6090C, C5NE6090B, C5NE6090E, C5NN6090B, C7NN6090AC, C7NN6090AL, C7NN6090N, C7NN6090T, C5NN6090L, Not a welded head, Ports: Intake - Square, Exhaust - Square, Cylinders 4, 1/2" head bolts, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, Has two coolant ports on intake side of head - One between Cylinders 1 and 2 and second after cylinder 4 -Uses intake gasket 82845236 / C6NE9439A, (Item #: 200152)$970.01
No Picture
Cylinder Head, Remanufactured, D3NN6090E - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 6710, 7000, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) 256 (Diesel), 268 (Diesel), Replaces Ford Casting number D3NN6090E, D3NN6090L, D5NN6090E, D5NN6090L, D9NN6090BA, Ports: Intake - Round, Exhaust - Square, Not a welded head, Cylinders 4, 1/2" head bolt, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, 4 coolant ports on intake manifold side of head - Between all cylinders and after cylinder 4, Uses Ford intake gasket D9NN9439AA, E8NN9439BA, or 83964125, (Item #: 200142)$520.01
No Picture
Cylinder Head, Remanufactured, E6NN6090AB - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 6710, 7000, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) 256 (Diesel), 268 (Diesel), Replaces Ford Casting number E6NN6090AB, 87800097, Ports: Intake - Square, Exhaust - Square, Cylinders: 4, 9/16" head bolts, Not a Welded Head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, 4 coolant ports on intake manifold side of head - Between all cylinders and after cylinder 4, Uses Ford intake gasket E6NN9439AB, For a Remanufactured version of this sku use Item #: 210686, (Item #: 210685)$520.01
Cylinder Head, Used - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 6710, 7000, 7600, 7610, 7700, 7710, Compatible with Ford Engine(s) 256 (Diesel), 268 (Diesel), Replaces Ford Casting number C0NN6090C, C5NE6090B, C5NE6090E, C5NN6090B, C7NN6090AC, C7NN6090AL, C7NN6090N, C7NN6090T, C5NN6090L, Ports: Intake - Square, Exhaust - Square, Cylinders: 4, 1/2" head bolts, Our used cylinder heads have been visually inspected for cracks, Cylinder head may require further cleaning, inspection, or machining before use, Has two coolant ports on intake side of head, One between Cylinders 1 and 2 and second after cylinder 4, Uses intake gasket 82845236 - C6NE9439A, For a Remanufactured version of this part use Item #: 204489, (Item #: 400152)$321.01
No Picture
Cylinder Head with Valves, Remanufactured, C0NN6090C - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 6710, 7000, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) 256 (Diesel), 268 (Diesel), Replaces Ford Casting number C0NN6090C, C5NE6090B, C5NN6090B, C7NN6090AC, C7NN6090AL, C7NN6090N, C7NN6090T, C5NE6090E, C5NN6090L, Not a welded head, Ports: Intake - Square, Exhaust - Square, Cylinders: 4, 1/2" head bolts, Our remanufactured cylinder heads are reconditioned and ready for assembly, with valves installed, Cleaned and tested for cracks, Has two coolant ports on intake side of head - One between Cylinders 1 and 2 and second after cylinder 4 -Uses intake gasket 82845236 / C6NE9439A, (Item #: 204489)$1050.01
Cylinder Head with Valves, Remanufactured, D5NN6090L - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 6710, 7000, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) 256 (Diesel), 268 (Diesel), Replaces Ford Casting number D5NN6090L, D3NN6090E, D3NN6090L, D5NN6090E, Not a Welded Head, Ports: Intake - Round, Exhaust - Square, Cylinders: 4, 1/2" head bolt, Our remanufactured cylinder heads are reconditioned and ready for assembly, with valves installed, Cleaned and tested for cracks, 4 coolant ports on intake manifold side of head - Between all cylinders and after cylinder 4, Uses Ford intake gasket D9NN9439AA, E8NN9439BA, or 83964125, (Item #: 205177)$1050.01
No Picture
Cylinder Head, with Valves, Remanufactured, E6NN6090AB - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 6710, 7000, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) 256 (Diesel), 268 (Diesel), Replaces Ford Casting number E6NN6090AB, 87800097, Ports: Intake - Round, Exhaust - Square, Cylinders: 4, 9/16" head bolts, Not a Welded Head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with valves installed, Cleaned and tested for cracks, 4 coolant ports on intake manifold side of head - Between all cylinders and after cylinder 4, Uses Ford intake gasket E6NN9439AB, For a Remanufactured version of this sku use Item #: 210685, (Item #: 210686)$1050.01
Engine Balancer - For 2000 3 cylinder gas, 3000 gas, 4000 3 cylinder gas, 5000 gas and diesel, 5600, 6600, 6610, 6700, 6710, 6810, 7000, 7410, 7600, 7610, 7700, 7710. Replaces 87802137, D9NN6A311AD, 83924287. Used through 8/1986. 1/2 inch wide gears. (Item #: 168875, Ref: D9NN6A311AD)$393.00
No Picture
Exhaust Valve - .003" Oversize Stem - For Ford tractor models TW5, TW10, TW20, TW30, 5600, 5700, 6000, 6600, 6610, 6700, 6710, 7000, 7600, 7700, 7710, 8700, 9000, 9200, 9600, 9700, Compatible with Ford Engine (s) 256, 256T, 268, 268T, 401, 401T, Replaces Ford OEM number D8NN6505BA, Replaces manufacturer number VPA1571, Size: .003" Oversized Stem, (Item #: 176472)$17.80
Flywheel With Ring Gear - Used on Ford 3400 (1/1/65-5/31/68), 5000, 5100, 5190, 5200, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 335, 340, 3500 (1/1/65-5/31/68) all with 12 inch clutches. This new flywheel includes E2NN6384AA - 128 tooth ring gear. This part replaces E0NN6375HA (Item #: 159167, Ref: E0NN6375HA)$867.00
Freeze Plug - Used on Ford / New Holland tractors 1965 and later, this freeze plug is 1.18 inches in diameter (Item #: 173014, Ref: 390625S)$2.10
Front Engine Plate, Used - For Ford tractor models 2000, 2100, 2110, 2120, 2150, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3120, 3190, 3230, 3300, 3310, 3330, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4140, 4190, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4600SU, 4610, 4610SU, 4630, 4830, 5000, 5030, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7810, 7810S, 8240, 8340, 9030, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 250C, 260C, 276, 333, 334, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 515, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 555E, 575D, 575E, 650, 655C, 655D, 655E, 675D, 675E, 750, 755, 755A, 755B, Compatible with Ford Engine(s) BSD332, BSD333, 256 Replaces Ford OEM nos E5NN6C044A, 83956700, , Compatible with New Holland tractor models TB80, TB85, TB90, TB100, TB110, TB120, TS90, TS100, TS110, TS115, 5610S, 6610S, 6640, 6810S, 7010, 7610S, 7740, 7840, 8010, 8340, Compatible with New Holland Skid Steer Loader(s) L781, L783, L785, L865, LS180, LX865, LX885, Compatible with New Holland Hay Cutting(s) 1499 (s/n 540289-later), 2450 (s/n 606630-earlier), 2550 (s/n 606630-earlier), Replaces New Holland OEM nos E5NN6C044A, 83956700, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 434395)$30.01
Gear Selector Arm - For Ford tractor models 5000, 5600, 5610, 5610S, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7600, 7610, 7700, 7710, 7810S, Replaces Ford OEM number C5NN7346A, E5NN7346AA, 83955498, (Item #: 161525)$58.00
No Picture
Gear Selector Arm, Used - For Ford tractor models 5000, 5600, 5610, 5610S, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7600, 7610, 7700, 7710, 7810S, Replaces Ford OEM number C5NN7346A, E5NN7346AA, 83955498, For a new version of this item use Item #: 161525, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 436264)$38.01
Idler Pulley With Bracket - This Idler Pulley With Bracket is used on multiple Ford / New Holland Agriculture and Industrial models. It replaces part numbers 83986807, E6NN8A614AB (Item #: 160935, Ref: E6NN8A614AB)$112.00
Intake Valve Seal - Used on Ford / New Holland equipment, 1965 and later with BSD diesel engines (not Shibaura engines), this seal replaces OEM numbers 81804329, 86602420, C5NE6571A, 1804329. Used on 3, 4 and 6 cylinder engines. One used per intake valve. Sold individually. (Item #: 166331, Ref: C5NE6571A)$0.80
Push Rod - For 2600, 3600, 3900, 4100, 4600, 5600, 5700, 6600, 6700, 7700, 231, 233, 333, 420, 515, 532, 535. All with 3 or 4 cylinder Diesel from 1975 to 1981. Push Rod 12.17 inches long. (Item #: 165225, Ref: C5NE6567B)$5.60
Push Rod, Used - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2000, 2100, 2110, 2120, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3120, 3190, 3230, 3300, 3310, 3330, 3400, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4140, 4190, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8200, 8210, 8400, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9030, 9200, 9600, 9700, Compatible with Ford Construction and industrial models A62, A64, A66, 230A, 231, 233, 234, 250C, 260C, 276, 333, 334, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 515, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 675D, 750, 755, 755A, 755B, 5500, 5550, 6500, 7500, Compatible with Ford Engine(s) BSD332, BSD333, BSD442, BSD444, BSD444T, BSD666, BSD666T Replaces Ford OEM nos 81813399, , Compatible with New Holland Skid Steer Loader(s) L783, L785, L865, LS180, LX865, LX885, Compatible with New Holland Hay Cutting(s) 1118, 1499 Replaces New Holland OEM nos 81813399, , Compatible with Versatile Hay Cutting(s) 4750, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 443449)$3.86
Rear Engine Seal Retainer - Used Ford / New Holland engines BSD442, BSD444, BSD444T, BSD666, BSD666T on equipment 1975 and later. The retainer is used with E5NN6701BA crankshaft seal and E9NN6N305AB gasket, sold separately. This part replaces original part numbers E5HN6N306AB, E5HN6N306AC, 81868536 (Item #: 168950, Ref: E5HN6N306AB)$163.00
Ring Gear, Flywheel - This ring gear is for gas and diesel. Measures 16.115 outside diameter, 14.52 inside diameter, .625 width and has 128 teeth. For models 2000, 3000, 4000, 5000, 6000, 7000, all 1965-1975. For 2600, 3600, 4600, 5600, 6600, 7700, all 1975-1981. For 5000 gas 6/1971-1975. For 3230, 3430, 3930, 4130, 4430, 4830, 5030, 3/1990 and up. Also used on many industrials and later models. Replaces C5NE6384AA, 83949153, 82954183, 9710967, 500791, 18042303, 80873368, 873368, 3949153. Starter Flywheel Ring Gear. (Item #: 111310, Ref: E2NN6384AA)$39.00
Seal Retainer Plate, Used - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2310, 2600, 2610, 2810, 2910, 3230, 3430, 3600, 3610, 3900, 3910, 3930, 4100, 4110, 4130, 4600, 4610, 4630, 4830, 5030, 5110, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8200, 8210, 8400, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9030, 9200, 9600, 9700, Compatible with Ford Construction and industrial models A64, A66, 230A, 231, 233, 234, 250C, 260C, 276, 333, 334, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 515, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 555, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 675D, 755A, 755B, Compatible with Ford Engine(s) BSD332, BSD333, BSD442, BSD444, BSD444T, BSD666, BSD666T Replaces Ford OEM nos E5HN6N306AC, , Compatible with New Holland Combine(s) TR86, TR87, TR96, TR97, TX36, Compatible with New Holland Skid Steer Loader(s) L783, L785, L865, LS180, LX865, LX885, Compatible with New Holland Bale Movers(s) 1078, 1079, 1085, Compatible with New Holland Hay Cutting(s) 1118, 1499, Compatible with Versatile Hay Cutting(s) 4750, No Holes in bottom of seal, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 434438)$31.01
Valve Lifter, Used - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2000, 2310, 2610, 2810, 3000, 3230, 3430, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4600, 4610, 4630, 4830, 5000, 5030, 5110, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7410, 7600, 7610, 7700, 7710, 7740, 7810, 7840, 7910, 8000, 8160, 8200, 8210, 8260, 8340, 8360, 8530, 8560, 8600, 8630, 8700, 8730, 8830, 9000, 9600, 9700, Compatible with Ford Construction and industrial models 550, 555, 555E, 575E, 655, 655E, 675E, Compatible with Ford Engine(s) BSD326, BSD329, BSD332, BSD333, BSD442, BSD442T, BSD444, BSD444T, BSD666, BSD666T Replaces Ford OEM number C7NN6500B, C5NE6500C2, 83946434, E4HN6500AA, 83957729, C5NE6500C, , Compatible with New Holland tractor models TB90, TB100, TB110, TB120, TS80, TS90, 7010, 8010, 8240, For a new version of this item use Item #: 112190, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435585)$4.76
No Picture
Valve Service Kit - For tractor models 5000, 5600, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. Contains: springs and locks, (no valves). (Item #: VSKF233)$44.16
Valve Spring - Used on for 158, 175, 192, 201, 256, 268 and 401 CID gas and diesel engines. One used per valve. It replaces C7NN6513A, D6NN6513A, 81817098, 83911693. (Item #: 166305, Ref: D6NN6513A)$3.10
Engine Pistons and Sleeves
Piston and Ring Kit - .020 inch oversize Piston and Ring Kit. For 5000, 5600, 5700. (Item #: 166363, Ref: PRK233-020)$59.22
Piston and Ring Kit - .030 inch oversize Piston and Ring Kit. For 5000, 5600, 5700. (Item #: PRK233-030)$288.45
Piston and Ring Kit - .040 inch oversize Piston and Ring Kit. For 5000, 5600, 5700. (Item #: PRK233-040)$395.09
Piston and Ring Kit - .020 inch oversize Piston and Ring Kit. For 5000, 5600, 5700, 6600, 6700. (Item #: PRK256-020)$413.67
Piston and Ring Kit - .030 inch oversize Piston and Ring Kit. For 5000, 5600, 5700, 6600, 6700. (Item #: PRK256-030)$303.77
Piston and Ring Set .030 - .030 inch oversize piston and ring set for tractor models with 175 CID 3 cylinder and 233 4 cylinder diesel engines, 4.2 inch standard bore, 2.763 inch compression distance. This is a piston and ring set for one cylinder. Three or four are required for complete engine. Replaces D6NN6108L-30 YTO PRK175-030 (Item #: 166372, Ref: PRK175-030)$98.00
Piston Pin Bushing - Fits 158 CID gas and diesel, 175 CID gas and diesel, 192 CID gas, 201 CID diesel, 233 CID diesel, 256 CID gas and diesel and 268 CID diesel. For tractor models 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710. (Item #: 128600, Ref: C5NE6207A)$5.00
Piston Sleeve - (FORD) Sleeve- Cylinder - Finished - Sleeve only. 4.4 inch bore diesel engine. Replacement for re-bore kits listed. Finished bore and honed. (Item #: 160021, Ref: RBS514)$36.00
Piston Sleeve - Engines 401 CID Diesel and Turbo Diesel, 192 CID Gas, 201 Gas and Diesel, 256 CID Gas and Diesel, 256 Turbo Diesel, 233 Diesel, 268 Non Turbo and Turbo Diesel. Semi-Finished 4.4 inch bore used when boring Non Sleeved Engine. For tractor models 3000, 4000, 4600, 4610, 5000, 5600, 5700, 6000, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 8000, 8200, 8600, 8700, 9000, 9200, 9600, 9700, TW10, TW20, TW30. (Item #: 160021, Ref: SD753)$36.00
Piston Sleeve, 4.2 Inch Bore - This is a semi-finished straight sleeve (no lip) for 4.2 inch bore engines. It is used when repairing non-sleeved engines, boring and honing required. Inside diameter 105.530mm (4.200 inches). Outside diameter 110.870mm (4.362 inches). Overall height 209.550mm (8.250 inches). Replaces 81815327, 87295246, C5NN6055A (Item #: 160001, Ref: C5NN6055A)$35.00
Piston Sleeve, 4.4 Inch Bore - This is a semi-finished straight (non-flanged) sleeve for 4.4 inch bore engines. It is used when boring non sleeved engines. Length 8.21 inches, Inside Diameter 4.4 inches and Outside Diameter 4.6 inches. Replaces 81823241, 83912946, C9NN6055A, D0NN6055B, D7NN6055A (Item #: 108763, Ref: D7NN6055A)$46.00
Piston Sleeve, 4.4 Inch Bore - This is a semi-finished flanged sleeve for 4.4 inch bore engines. Inside diameter of 4.4 inches, outside diameter 4.50 inches, Flange lip .100 inches, diameter at flange 4.738 inches and overall length is 8.21 inches. This sleeve is for boring non-sleeved engines. Block must be counterbored for sleeve flange. Replaces 83912946, 81823241, 81829308, C9NN6055A, D7NN6055A (Item #: 160021, Ref: D7NN6055AFL)$36.00
Piston with Pin - Standard Bore Piston, 4.2 inch standard bore. This piston has a pin diameter of 1.50 inches and compression height from the center of the piston pin to the top of the piston is 2.770 inches. For tractor models 3000, 3600, 5000, 5600, 5700. All with either 175 CID or 233 CID 3 Cylinder Diesel Engines. (Item #: 172902, Ref: D4NN6108L)$130.00
Piston with Pin - .040 inch Oversize Piston, 4.2 inch standard bore. This piston has a pin diameter of 1.50 inches and compression height from the center of the piston pin to the top of the piston is 2.770 inches. For tractor models 3000, 3600, 5000, 5600, 5700. All with either 175 CID or 233 CID 3 Cylinder Diesel Engines. (Item #: 184686, Ref: D4NN6108S)$40.98
Piston with Pin, .030 - .030 inch Oversize Piston, 4.2 inch standard bore. This piston has a pin diameter of 1.50 inches and compression height from the center of the piston pin to the top of the piston is 2.770 inches. For tractor models 3000, 3600, 5000, 5600, 5700. All with either 175 CID or 233 CID 3 Cylinder Diesel Engines. (Item #: 173481, Ref: D4NN6108R)$84.00
Piston with Pin and Rings - .020 inch Oversize Piston, 4.2 inch standard bore. This piston has a pin diameter of 1.50 inches and compression height from the center of the piston pin to the top of the piston is 2.770 inches. For tractor models 3000, 3600, 5000, 5600, 5700. All with either 175 CID or 233 CID Diesel Engines. Replaces D4NN6108N, 83910852, 83910853, D6NN6108N. (Item #: 166363, Ref: D4NN6108N)$59.22
Piston With Pin, STD - For 256 Diesel Engine (Standard 4.4 inch bore) in: 5000, 5600, 5700, 6600, 6700. (Item #: 172695, Ref: D4NN6108AA)$34.98
No Picture
Piston with Rings - For tractor models (3000 1965-1975), (5000 1965-3/1968), (5600, 5700 1975-9/1980). (Item #: 128696, Ref: RK156)$98.00
Piston and Rings, .020" - For Ford tractor models 650, 5000, 5100, 5190, 5200, 5340, 5550, 5600, 5610, 5900, 6500, 6700, Compatible with Ford Construction and industrial models 655, 655A, Compatible with Ford Engine (s) 256 Replaces Ford OEM number D4NN6108A-20, , Compatible with New Holland Hay Cutting (s) 907, 909, 910, 912, 1100, 1112, 1114, 1495, .020", (Item #: 167119)$128.00
Piston Pin Bushing - For Ford tractor models TW5, TW15, TW25, TW35, 2600, 3600, 3900, 4100, 4600, 4600SU, 5110, 5600, 5610, 5640, 5700, 5900, 6600, 6610, 6640, 6700, 6710, 6810, 7410, 7610, 7710, 7740, 7810, 7840, 7910, 8210, 8240, 8340, 8530, 8630, 8730, 8830, Compatible with Ford Construction and industrial models 231, 233, 333, 335, 420, 515, 531, 532, 535, Replaces Ford OEM number F0NN6207BA, (Item #: 166314)$22.90
Piston Rings, Diesel, .020 - Piston Rings FOR 1 PISTON, Diesel 4.2 inch bore, 3 and 4 Cylinder Engines, 158, 175 and 233 CID. .020 inch Oversize Ring Kit for 1 Piston. For: 2000, 2600, 3000, 3500, 3600, 5000, 5600, 5700. (Item #: 120761, Ref: CFPN6149AT)$6.00
No Picture
Piston Ring Set, .020, 201 CID Diesel - .020 inch Oversize Ring Set for 1 Cylinder. For 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710, 8000. Sold per Cylinder. (Item #: CFPN6149BD)$22.37
No Picture
Piston Ring Set, .030, 201 CID Diesel - .030 inch Oversize Ring Set for 1 Cylinder. For 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710, 8000. Sold per Cylinder. (Item #: CFPN6149BE)$26.07
No Picture
Piston Ring Set, Diesel, .030 - Diesel 4.2 inch bore, 3 and 4 Cylinder Engines, 158, 175 and 233 CID. .030 inch Oversize Ring Kit for 1 Piston. For: 2000, 2600, 3000, 3500, 3600, 5000, 5600, 5700. (Item #: 120762, Ref: CFPN6149AU)$20.40
No Picture
Piston Ring Set, Diesel, .040 - Diesel 4.2 inch bore, 3 and 4 Cylinder Engines, 158, 175 and 233 CID. .040 inch Oversize Ring Kit for 1 Piston. For: 2000, 2600, 3000, 3500, 3600, 5000, 5600, 5700. (Item #: 120763, Ref: CFPN6149AV)$16.90
No Picture
Piston Ring Set, Diesel, STD - Diesel 4.2 inch bore, 3 and 4 Cylinder Engines, 158, 175 and 233 CID. Contains 3 Compression Rings at 3/32 and 1 Oil Ring at 3/16. Standard Ring Kit for 1 Piston for: 2000, 2600, 3000, 3500, 3600, 5000, 5600, 5700. (Item #: 120760, Ref: CFPN6149AS)$19.80
No Picture
Piston Ring Set, STD, Diesel - Standard Ring Set for 1 Piston. 4.4 bore. Compression rings at 3/32 inch, and Oil ring at 3/16 inch. For Tractor Models 4000, 4600, 5000, 5600, 5700, 6600, 6610, 6700, 6710, 8000. 3, 4 or 6 needed depending on Engine. Sold per Cylinder. (Item #: 120770, Ref: CFPN6149BC)$20.60
Exhaust System
Exhaust Manifold, Vertical - Fits the following 4 cylinder 1975 and newer (NON Turbo) tractors: 5030, 5600, 5610, 6610, 6700, 6710. Does not come with gasket. Gasket can be ordered as part number C5NE9448B. (Item #: 101526, Ref: D3NN9430B)$46.98
Manifold Gasket - The Gasket is used with Manifolds: D1NN9430A, C5NE9430D, D3NN9430B. It replaces original part numbers 83983680C5NE9448B, E8NN9448AA, E8NN9448BA (Item #: 101525, Ref: C5NE9448B)$6.90
Air Cleaner Dust Collector - This Air Cleaner Dust Collector Valve has a 3 inch inside diameter. It is used on multiple Ford/New Holland models. It replaces original part numbers 81870839, D2NN9C673B, F0NN9C673AA. (Item #: 121925, Ref: T23262)$6.00
Air Cleaner Hose - This Air Cleaner Hose fits 231, 233, 2600, 2600V, 333, 335, 3600, 3600V, 3900, 4600, 4600SU, 5110, 515, 531, 532, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710. The large end diameter is 2 1/2 inches and the small end is 2 inch. It replaces OEM part number D9NN9B640AA. (Item #: 182918, Ref: D9NN9B640AA)$12.70
No Picture
Air Filter, Inner - This Inner Filter measures 13 3/8 inches long and 3 inches diameter. For tractor models 2310, 2610, 2810, 2910, 3230, 3430, 3610, 3910, 4110, 4130, 4610, 4630, (5600, 5700, 6600, 6700 from 4/1976 and up), 5610, 5900. (Item #: 126019, Ref: D6NN9R500B)$43.00
No Picture
Air Filter, Outer - This Outer Air Filter measures 5 3/8 outside diameter, .437 inch inside diameter on top and 3.063 inches diameter on the bottom. Overall length is 15 inches. For tractor models 2310, 2610, 2810, 2910, 3230, 3430, 3610, 3910, 3930, 4110, 4130, 4610, 4630, (5600, 5700, 6600, 6700 from 4/1976 and up), 5610. (Item #: 181888, Ref: D6NN9601B)$46.00
Breather Cap - 2-1/2" - For Ford tractor models 4100, 4600, 5600, 6600, 6700, Replaces Ford OEM number 81837758, D3NN9A660D, For Tractors With 2-1/2" Intake Pipe, (Item #: 112382)$25.00
Double Filter Head - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2310, 2600, 2610, 2810, 2910, 3600, 3610, 3900, 3910, 4100, 4110, 4600, 4610, 5110, 5600, 5610, 5700, 6410, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8210, 8530, 8630, 8730, 8830, Compatible with Ford Construction and industrial models A64, A66, 230A, 231, 233, 234, 333, 334, 335, 420, 515, 530A, 531, 532, 535, 550, 555, 555A, 555B, 655, 655A, Compatible with Ford Engine(s) BSD332, BSD333, BSD442, BSD444, BSD444T, BSD666, BSD666T Replaces Ford OEM number 83914031, D8NN9N180AA, 84515567, D9NN9165AA, , Compatible with Massey Ferguson tractor models 3090, 3630, 3650 Replaces Massey Ferguson OEM nos 1895160M1, , Compatible with New Holland Hay Cutting(s) 1118, (Item #: 165353)$31.00
Electric Fuel Lift Transfer Pump - For Ford tractor models 2600, 3600, 3900, 4100, 4600, 5600, 5610, 5700, 6600, 6700, 6710, 7600, 7700, 7710, Compatible with Ford Construction and industrial models 231, 233, 333, 335, 420, 515, 531, 532, 535, Replaces Ford OEM number 87029971, 83928144, D8NN9350BB, 12 Volt, Minimum Shut off Pressure 4 PSI, Maximum Shut off Pressure 5.5 PSI, Fitting Type: 1/8" -27 Internally Threaded, Minimum Dry Lift: 24", Includes Anti-Siphon Valve, (Item #: 159080)$171.00
Foot Accelerator Control Kit - For Ford tractor models 5100, 5600, 6100, 6600, 7100, 7600, Replaces Ford OEM number D2NN9735C, 81827473, (Item #: 154927)$43.10
Friction Disc for Throttle Control Lever - This Throttle Friction Disc is 3 inches in diameter and has a 1/2 inch center hole. Replaces part number C5NN518B, 83924272, 83977032, 9N518, E6NN9R536AA, 311503. (Item #: 111446, Ref: C5NN518B)$1.90
Fuel Cap, Vented - This silver Fuel Cap is for Under Hood Fuel Tank. 2-7/8 inch outside diameter, 1/4 inch tall, Zinc finish, 1.788 inch edge of tang to edge of tang. Vented Verify OEM number for tractor models 1100, 1120, 1120, 1200, 1210, 1215, 1220, 1300, 1210, 1320, 1500, 1510, 1520, 1620, 1700, 1710, 1715, 1720, 1900, 1910, 2110, 2120, 3415, 2000, 2310, 2600, 2610, 2810, 2910, 3000, 3600, 3610, 3900, 3910, 4000, 4100, 4110, 4600, 4610, 5000, 5600, 5610, 5700, 6000, 6600, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8200, 8210, 8530, 8630, 8700, 8700, 8830, 9000, 9200, 9700. Replaces 83961128, SBA360300080, E7NN9030AA. There are other Fuel Caps for some of these tractors please verify OEM number and measurements. (Item #: 184806, Ref: C5NN9030B)$8.80
Fuel Filter Assembly, Double - Universal Double Fuel Filter Assembly fits most Ford Diesels 1965 and newer that use CAV type Double Filter Assembly. Comes complete with filters. Filter brands may vary. Replaces EBPN9N166AA, E5NN9165BA, C5NN9165C and D2NN9165C. This assembly has two connections on each side to accommodate 1 inlet and 1 outlet ON EACH SIDE. You may have to reconfigure your inlet and outlet hoses. 1/2 inch x 20 UNF Ports. Outer ports in, inner ports out. (Item #: 113747, Ref: S.60426)$29.30
Fuel Filter Assembly, Single - This Fuel Filter assembly comes with a metal bowl. For Diesel tractors using CAV type injection system. Includes filter. Uses replacement filter CAV7111296. (Item #: 115053, Ref: S.60425)$21.60
Fuel Filter Assembly, Single - This is a Single Filter Assembly with Glass Bowl. Ports are 1/2 inch x 20 pitch. Includes bleeder port and screw. Replaces original part numbers 83937061, C5NE9165C, C7NN9162B, D9NN9165BA. Replacement filter for this unit is CAV7111296. (Item #: 183733, Ref: 1446017M91)$35.00
Fuel Filter Bolt Assembly - Fuel bowl bolt assembly Replaces 9918145, 9918125, 81825363 May be used in other applications, such as : Claas, Fendt, Fiat, JCB, Kioti, Landini, Land Rover, Lamborghini, Leyland, Long Tractor, Matbro, McCormick, Merlo, Mitsubishi, Nuffield, Renault, Same, Satoh, Volvo (Item #: 179323, Ref: 81825363)$15.30
Fuel Injection Pump, Remanufactured, E4NN9A543DC, Simms, P5498A - For Ford tractor models 5000, 5600, 5610, 5900, 6600, 6610, 6700, 6710, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) BSD442 (1/1981 and Later), BSD444 (1/1981 and Later), BSD444T (1/1981 and Later), Replaces Ford OEM number E4NN9A543DC, D9NN9A543GA, E4NN9A543DA, E4NN9A543DB, Replaces Simms manufacturer number P5498A, P55982E, For LH Throttle Lever Applications, (Item #: 210687)$2320.01
Fuel Injection Pump, Remanufactured, E4NN9A543DC, Simms, P5498A - For Ford tractor models 5000, 5600, 5610, 5900, 6600, 6610, 6700, 6710, 7600, 7610, 7700, 7710, Compatible with Ford Engine (s) BSD442 (S/N 1/1981 and later), BSD444 (S/N 1/1981 and later), BSD444T (S/N 1/1981 and later), Replaces Ford OEM number E4NN9A543DC, D9NN9A543GA, E4NN9A543DA, E4NN9A543DB, Replaces Simms manufacturer number P5498A, P55982E, For RH Throttle Lever Applications, (Item #: 210688)$2320.01
Fuel Injections Line Set - Used on Ford Equipment 1975 and later with DPA/CAV injection pumps. This set contains (1) D9NN9A555BA, (1) D9NN9A556BA, (1) D9NN9A557BA, (1) D9NN9A558AA. The set replaces D5NN9A555B, D3NN9A556C, D5NN9A558B. Used on Ford models: 5600, 5610, 5700, 5900, 650, 6600, 6610, 6700 (Item #: 162821, Ref: FPL200)$62.00
Fuel Injector, Remanufactured, D9NN9F593CA - For Ford tractor models TW5 (6 Cylinder), TW15 (6 Cylinder), TW25 (6 Cylinder), TW35 (6 Cylinder), 2600 (3 Cylinder), 3600 (3 Cylinder), 3900 (3 Cylinder), 4100 (3 Cylinder), 4600 (3 Cylinder), 4600SU (3 Cylinder), 5110 (3 Cylinder), 5600 (4 Cylinder), 5610 (4 Cylinder), 5700 (4 Cylinder), 5900 (4 Cylinder), 6410 (4 Cylinder), 6500 (4 Cylinder), 6600 (4 Cylinder), 6610 (4 Cylinder), 6700 (4 Cylinder), 6710 (4 Cylinder), 6810 (4 Cylinder), 7410 (4 Cylinder), 7600 (4 Cylinder), 7610 (4 Cylinder), 7700 (4 Cylinder), 7710 (4 Cylinder), 7810 (6 Cylinder), 7910 (6 Cylinder), 8210 (6 Cylinder), 8530 (6 Cylinder), 8630 (6 Cylinder), 8730 (6 Cylinder), 8830 (6 Cylinder), Compatible with Ford Construction and industrial models A62 (4 Cylinder), A64 (4 Cylinder), A66 (4 Cylinder), 231 (3 Cylinder), 233 (3 Cylinder), 333 (3 Cylinder), 335 (3 Cylinder), 420 (3 Cylinder), 515 (3 Cylinder), 531 (3 Cylinder), 532 (3 Cylinder), 535 (3 Cylinder), 650 (4 Cylinder), 750 (4 Cylinder), 755 (4 Cylinder), 755A (4 Cylinder), 755B (4 Cylinder), 7500 (4 Cylinder), Compatible with Ford Engine (s) BSD442, BSD444, BSD444T, BSD666, BSD666T Replaces Ford OEM number D9NN9F593CA, 3919128, D9NN9F593LAR, , Compatible with New Holland Hay Cutting (s) 1118, For a New version of this sku use Item #: 119909, (Item #: 210593)$164.01
Fuel Injector, Remanufactured, D9NN9F593DA - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2600, 3600, 3900, 4600, 4600SU, 5110, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8200, 8210, 8400, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9200, 9600, 9700, Compatible with Ford Construction and industrial models A62, A64, A66, 231, 233, 333, 335, 420, 515, 531, 532, 535, Compatible with Ford Engine (s) BSD442, BSD444, BSD666, Replaces Ford OEM number D9NN9F593DA, For a New version of this sku use Item #: 119904, (Item #: 210002)$165.01
Fuel Injector Seal Kit - For (1) injector on: post 1965 tractors with 3 -6 cylinders models. Includes cork dust seal, copper compression seal and 2 aluminum return line seals. Replaces Replaces: 380428S, 380428S43, 81806142, 81806277, 81821105, 81867564, 83995430, C5NE9E529A, C5NE9F596A, C5NE9G546A (Item #: 156291, Ref: C5NE9F596A)$2.20
Fuel Pump Repair Kit - This Fuel Pump Repair Kit is used to repair fuel pump part numbers: D8NN9350AB, 510E-9350, 3912071, 83991467, 86525137, D3NN9350A, D8NN9350AA, D8NN9350AB, DDN9355. (Item #: 172699, Ref: S40569)$20.60
No Picture
Fuel Sending Unit - This Fuel Sending Unit is mounted with 6 bolts and is for 4 cylinder engine. For 5600, 6600, 7610, 5610S, 6610S, 7610S, 7810, 5110, 531, 532, 5900, 6410, 6600 and 8010S. Also replaces D8NN9A316LA. (Item #: 119735, Ref: D8NN9A316LB)$81.00
Fuel Shut-Off Cable - Cable Assembly, Fuel Shut-Off, 60 inch long. For Diesel Tractors 2000, 3000, 4000, 5000, 7000, (1965 to 1975); 2600, 3600, 3900, 4100, 4600, 5600, 6600, 7600, 233, 333, 335, 515, (1975 to 1981); 4610, 5610, 6610, 7610, 7710, with quiet cab (1981 to 1991). (Item #: 121221, Ref: E5NN9C331EA)$8.60
Fuel Tank - For tractor models: 5000, 5100, 5600, 6600, 7600. Fuel Tank. NOT FOR 5600 OR 6600 MODELS WITH CAB. Not for SIMM injection pump. (Item #: 103895, Ref: D5NN9002AE)$147.00
Fuel Tank - For Diesel 5000 (with CAV injection pumps, 1965-1975), 5600, 6600, 7600 (1975-1981). Not for SIMM injection pump. (Item #: 103895, Ref: D0NN9002B_)$147.00
Fuel Tank, Diesel - For Diesel Models: 5000 with CAV injection pumps (1965-1975), 5600, 6600, 7600 (1975-1981), 5610, 6610, 7610. This Tank can be adapted to Gas by plugging the return line. This tank uses D8NN9A316JA Sending Unit, C5NN9030D Cap, C5NN9N283A Fuel Sender Lock Ring and E2NN9276AA Fuel Sender Lock Ring Seal, each sold separately. Not for SIMM type injection pump. (Item #: 103895, Ref: D8NN9002HA)$147.00
Fuel Tank Valve - plastic handle - For Ford tractor models Major, Super Major, 2000, 2310, 2600, 2610, 2810, 2910, 3000, 3230, 3430, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4600, 4610, 4630, 5000, 5550, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7600, 7610, 7700, 7710, 8000, 8200, 8400, 8600, 9000, 9200, 9600, Compatible with Ford Construction and industrial models 230A, 233, 234, 340A, 340B, 345C, 345D, 550, 555 (DTC), 655, 5500 Replaces Ford OEM number D1NN9N024B, 83935915, 83917402, C5NN9N024A, D1NN9N024A, D2NN9N024C, E1ADDN9189B, E0NN9N024AA, E2NN9N024AA, E2NN9N200A, , Compatible with New Holland tractor models TB80, TB85, TB90, TB100, TB110, TB120, TT55, TT75, Replaces New Holland OEM number D8NN9N024AB, 81830037, 83926534, D8NN9N024AA, Plastic Knob, 1/2" Pipe Thread Inlet, 5/16" Tube Outlet, For brass handle use Item #: 181076, (Item #: 111712)$7.98
Fuel Tank Valve Tap - Metal Fuel Tap with Screen for Gas and Diesel: Major, Super Major, 2000 (1965 and up), 2310, 2600, 2610, 2810, 2910, 3000, 3230, 3430, 3600, 3610, 3900, 3910, 3930, 4000 (1965 and up), 4100, 4110, 4130, 4600, 4610, 4630, 5000, 5600, 5610, 5700, 5900, 6600, 7000, 7600, 7610, 7700, 7710, 8000, 8600, 9000, 9600, 9700, TW10, TW20, TW30. INDUSTRIALS: 550, 555A, 555B, 655, 655A. Tank tap is 7/8" tapered by 14 pitch (1/2 pipe thread), fuel line is 1/2" by 20 pitch UNF (5/16 inch tubing nut). Replaces D1NN9N024B, 83935915, 83917402, C5NN9N024A, D1NN9N024A, D2NN9N024C, E1ADDN9189B, E0NN9N024AA, E2NN9N024AA, E2NN9N200A, D8NN9N024AB, 81830037, 83926534, D8NN9N024AA (Item #: 181076, Ref: E2NN9N024AA)$8.80
Fuel Transfer Pump - Lift Pump, 2-bolt. Mounts to Injection Pump. For Super Major (8-1961/1964), 2000, 2100, 2120, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3100, 3120, 3230, 3300, 3310, 3400, 3500, 3600, 3610, 3910, 4000, 4100, 4410, 5000, 5100, 5110, 5200, 5610, 6600, 6610, 7000, 7100, 7200, 7610, 7710. Fuel Transfer Pump. Used on 3, 4 and 6 Cylinder Diesel Engines. Replaces: 510E-9350, 3912071, 83991467, 86525137, D3NN9350A, D8NN9350AA, D8NN9350AB, DDN9355. Uses S40569 Repair Kit. (Item #: 106200, Ref: D8NN9350AB)$21.60
No Picture
Injection Line - #1 Cylinder - For Ford tractor models 5600 (1/75-5/80), 5610 (1/81-later), 5700 (1/75-5/80), 5900 (1/81-later), 6600 (1/75-12/76), 6610 (1/81-later), 6610 (O, 1/81-later), 6700 (1/75-12/76), Compatible with Ford Construction and industrial models 650 (1/75-12/77), Compatible with Ford Engine (s) BSD442 (1/81-9/85), 256, Replaces Ford OEM number D9NN9A555BA, 83919548, (Item #: 171495)$20.80
No Picture
Injection Line - #2 Cylinder - For Ford tractor models 5600 (1/75-5/80), 5610 (1/81-later), 5700 (1/75-5/80), 5900 (1/81-later), 6600 (1/75-12/76), 6610 (1/81-later), 6610 (O, 1/81-later), 6700 (1/75-12/76), Compatible with Ford Construction and industrial models 650 (1/75-12/77), Compatible with Ford Engine (s) BSD442 (1/81-9/85), 256, Replaces Ford OEM number D9NN9A556BA, 83919551, (Item #: 171585)$19.70
No Picture
Injection Line - #3 Cylinder - For Ford tractor models 5600 (1/75-5/80), 5610 (1/81-later), 5700 (1/75-5/80), 5900 (1/81-later), 6600 (1/75-12/76), 6610 (1/81-later), 6610 (O, 1/81-later), 6700 (1/75-12/76), Compatible with Ford Construction and industrial models 650 (1/75-12/77), Compatible with Ford Engine (s) BSD442 (1/81-9/85), 256, Replaces Ford OEM number D9NN9A557BA, (Item #: 171587)$19.60
No Picture
Injection Line - #4 Cylinder - For Ford tractor models 5600 (1/75-5/80), 5610 (1/81-later), 5700 (1/75-5/80), 5900 (1/81-later), 6600 (1/75-12/76), 6610 (1/81-later), 6610 (O, 1/81-later), 6700 (1/75-12/76), Compatible with Ford Construction and industrial models 650 (1/75-12/77), Compatible with Ford Engine (s) BSD442 (1/81-9/85), 256, Replaces Ford OEM number D9NN9A558AA, (Item #: 171588)$20.22
Injection Line Set - This Injection Line Set us used on 4 Cylinder Engines with CAV Rotary Injection Pump Fits Models 5600, 6600, 7600, 7700, 5610, 6610, 7610, 7710. Replaces D9NN9A555BA, D9NN9A556BA, D9NN9A557BA, D9NN9A558AA (Item #: 162821, Ref: FPL200)$62.00
No Picture
Injection Line Set - 3 Cylinder - For Ford tractor models 2600 (3 cyl, 1/75-12/81), 2600 (N, 3 cyl, 1/75-12/81), 2600 (R, 3 cyl, 1/75-12/81), 3600 (3 cyl, 1/75-12/81), 3600 (N, 3 cyl, 1/75-12/81), 3600 (NO, 3 cyl, 1/75-12/81), 3600 (V, 3 cyl, 1/75-12/81), 3600 (R, 3 cyl, 1/75-12/77), 3900 (3 cyl, 1/75-12/81), 4100 (3 cyl, 1/75-12/81), 4600 (3 cyl, 1/75-12/81), 4600 (O, ), 4600 (NO, 3 cyl, 10/75-12/81), 4600SU (3 cyl, 1/75-7/81), 5600 (4 cyl, 1/75-12/81), 5610 (4 cyl, 1/81-12/93), 5700 (4 cyl, 7/78-9/80), 5900 (4 cyl, 5/85-12/93), 6600 (4 cyl, 1/75-12/81), 6600 (O, 4 cyl, 1/75-12/81), 6600 (C, 4 cyl, 1/75-9/76), 6610 (4 cyl, 1/81-12/93), 6610 (O, 4 cyl, 1/81-10/91), 6700 (4 cyl, 1/75-12/80), Compatible with Ford Construction and industrial models 231 (3 cyl, 1/75-12/81), 233 (3 cyl, 1/75-12/81), 256V (3 cyl, 1/74-12/84), 333 (3 cyl, 1/75-12/81), 335 (3 cyl, 10/75-9/78), 420 (3 cyl, 10/75-9/78), 515 (3 cyl, 10/75-9/78), 531 (3 cyl, 1/75-12/81), 532 (3 cyl, 10/75-9/78), 535 (3 cyl, 10/75-9/78), Compatible with Ford Engine (s) BSD442 (4 cylinder, 1/81-later), 256 (Diesel), Replaces Ford OEM number D9NN9A555BA, D9NN9A556BA, D9NN9A557BA, For cylinders #1, #2, #3, Will fit some 4 cylinders, #1, #2, #3 cylinders lines, For Injection Line #1 only use Item #: 171587, (Item #: 169713)$61.00
Injection Pump Cover Plate - This Cover Plate is used with CAV injection pumps. Replaces Ford OEM nos C7NN9G578A, 81827350, 83903026, 83926998, D2NN9G578A, D4NN9G578A, E0NN9G578AA (Item #: 113720, Ref: E0NN9G578AA)$53.00
No Picture
Injector Nozzle - For tractor models (250C up to 3/1990), 334, 340B, 450, 540, 3610, 3910, (5600 from 10/1980 and up), (6610 5/1987 to 7/1987), (332 up to 9/1989), (442 up to 8/1987). (Item #: 182775, Ref: D9NN9E527BA)$22.98
Injector Nozzle - For tractor models 333, 335, 340, 340A, 445, 445A, 3600, 3900, 4100, 420, (5600 up to 9/1980). (Item #: 160121, Ref: D4NN9E527A)$34.00
Pre-Cleaner Assembly - 2" Inlet Pipe - For Ford tractor models 501, 600, 700, 800, 1800, 2000, 2110, 2120, 2130, 2300, 2310, 2600, 3000, 3055, 3120, 3190, 3300, 3310, 3330, 3400, 3500, 3600, 4000, 4030, 4110, 4120, 4130, 4190, 4330, 4340, 4400, 4410, 4500, 4600, 5000, 5190, 5340, 5600, 6600, 6700, Compatible with Ford Construction and industrial models 231, 233, 333, 335, 340, 420, 445, 531, 532, 535, 540, 545, 2030, 3550, 4040, 4140, Replaces Ford OEM number 86555327, B9NN9A660A, Pre-Cleaner Assembly For 2" Inlet Pipe, Small Bowl [7"], Color may vary, (Item #: 112376)$28.90
Precleaner Bowl - Precleaner Bowl of clear plastic with 10 1/2 inch outside diameter. Designed for tractors with a 3" to 4" inlet. Outer diameter measures 10-1/2 inches at the top. Side height measures 3 inches. Inner diameter of the cone measures 5-9/16 inches at the top. Overall height measures 4 inches. Replaces C9NN9A663A, 594075, 80330381, 81821685 (Item #: 107972, Ref: C9NN9A663A)$9.80
Throttle Rod Connector - This Throttle Rod Connector is made from plastic. It is used on Ford 2000, 3000, 4000, 4000SU, 5000, 7000, 2600, 3600, 4600, 4600SU, 5600, 6600, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4610SU, 5610, 6610, 7610, 7810, 5900, 5640, 6640, 7740, 7840, 8240, 8000, 9000, 8600, 9600, 9700, 231, 335, 531, 340, 540, 3400, 3500, 445, 4500, 250C, 340, 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 655, 655A. Replaces C5NN9740A, 81811646 (Item #: 167626, Ref: C5NN9740A)$8.40
Throttle Rod Grommet - This Throttle Rod Grommet is used on Ford Tractors 1953 to 1974. It Replaces original part numbers: 353873S, 83416731, 83935151. (Item #: 164360, Ref: 353873S)$2.50
Fuel Sending Unit - For tractor models 5000, 5100, (5110, 5610, 5900, 6410, 6610, 6810, 7610, before 11/1983), 5600, 6600, 7000, 7100, 7600. Used on Tank D8NN9002HA. C5NN9N283A Fuel Sender Lock Ring and E2NN9276AA Fuel Sender Lock Ring Seal, each sold separately. Replaces C5NN9A316A, D8NN9A316DA, D8NN9A316DB, D8NN9A316JA, D8NN9A3316DB, 81805895, 83914076, 83917491, 83917697 (Item #: 119734, Ref: D8NN9A316JA)$50.00
Fuel Sending Unit - This Fuel Sending Unit is mounted with 5 bolts and is for 4 cylinder engine. For 5600, 6600, 7610, 5610S, 6610S, 7610S, 7810, and 8010S. (Item #: 119737, Ref: E3NN9A316BA)$60.00
Fuel Sending Unit Lock Ring Seal - This Fuel Sending Unit Lock Ring Seal is used with C5NN9N283A Lock Ring and on tanks E2NN9002BA, C5NN9002AC and D8NN9002HA. Replaces original part number E2NN9276AA (Item #: 178193, Ref: E2NN9276AA)$4.40
Instrument Cluster - Speedometer moves counter clockwise. Metal Casting. For tractor models 2600, 3600, 4100, 4600, 5600, 6600, 7600 (1975 to 1981) also fits 2310, 2610, 2810, 2910, 3610, 3910, 4110, 4610, (1981 to 1990), 5610, 5900, 6610, 7610, (1981 to 9-1985), 230A, 234, 334, 335, 530A (1981 to 2-1990). Includes Instrument Stabilizer C7NN10N507A (not used in all applications). Replaces C7NN10849C, E5NN10849BA, D8NN10849TA, D8NN10849TB, D5NN10849A, 83904448, 83927301, 83958741, 83953544, E7NN10849BA (Item #: 103890, Ref: E5NN10849BA)$112.80
Instrument Cluster Seal - Instrument Cluster Gauge Gasket for 2000, 2600, 3000, 3600, 3400, 3500, 4400, 4600, 4000, 4610, 5600, 6600, 7600. Note, this seal does not have inset fasteners. That version of the seal is not available. (Item #: 127448, Ref: C5NN10A949C)$13.30
Sending Unit Lock Ring - For various fuel tanks such as E2NN9002BA, C5NN9002AC and D8NN9002HA which use a lock ring to secure the fuel sender (like the D8NN9A316KA). Fits many Ford Models, 1965 and later. Order Seal E2NN9276AA separately if needed. Replaces C5NN9N283A, 81811218. (Item #: 152001, Ref: C5NN9N283A)$5.00
Temperature Sender - Temperature Sender, Water. The part may come with a spade terminal which might require changing your wire end. 3/8 Inch NPT Thread.Replaces: 81818428, 83904449, 83904448, 81837742, 83911735, 83948391, 8712608, 82028131, 9712608, D8NN10884AA, E1NN10884AA, 2080406, 3917490, 73403367 (Item #: 128314, Ref: D5NN10884A)$9.70
Castle Nut - This is a 1 inch UNF Thread Castle Nut. It is used with E4NNF537AA Lower Link Pin and other applications where a 1 inch UNF thread Castle Nut is needed. It replaces 390767S36, 83958917, 14H920 (Item #: 158239, Ref: 390767S36)$4.30
Hook Bracket, Used - For Ford tractor models 5100, 5110, 5200, 5340, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, Replaces Ford OEM nos C5NNN876A, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 444323)$110.01
Hydraulic Lift Ram Arm - For Ford tractor models 5100, 5200, 5340, 5600, 5700, 5900, 6600, 6700, 7600, 7700, Replaces Ford OEM number C7NN545D, Hydraulic Lift Ram Arm, (Item #: 170953)$177.00
Hydraulic Lift Rocker - For Ford tractor models 5000, 5100, 5110 (2 pin), 5200, 5340, 5600, 5610, 5700, 6600, 6610 (2 pin), 6700, 6710 (2 pin), 6810 (2 pin), 7100, 7200, 7410 (2 pin), 7600, 7610 (2 pin), 7700, 7710 (2 pin), 7810, 7910, 8210, Replaces Ford OEM number E0NN535DA, For models with 2 speed PTO, (Item #: 162982)$120.00
Hydraulic Lift Rod - For Ford tractor models 5000, 5100, 5110, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7810, 7840, 7910, 8100, 8210, 8240, 8340 Replaces Ford OEM number C7NN526D, , Compatible with New Holland tractor models TB80, TB85, TB90, TB100, TB110, TB120, TS90, TS100, TS110, TS115, TV140, TV145, Replaces New Holland OEM number 81817891, (Item #: 155016)$34.30
No Picture
Leveling Arm - For Ford tractor models 5000, 5100, 5110, 5200, 5340, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7810, 7910, 8210, Replaces Ford OEM number C5NNB863C, C7NNA935C, Left hand, Adjusts from 25" to 31", Catagory 2, Additional Handling and Oversize Fees Apply To This Item, (Item #: 115657)$95.00
No Picture
Leveling Arm - For Ford tractor models 5000, 5100, 5110, 5200, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8210, Replaces Ford OEM number 81802073, C5NNB863C, E0NNA935AA, Left hand, Adjusts from 28" to 34", Catagory 2, Additional Handling and Oversize Fees Apply To This Item, (Item #: 115659)$114.00
Leveling Box - Box Assembly, Leveling Right Hand, Category II, adjustment is 25 inches to 31 inches. For 5000, 5600, 5610, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710 Replaces C5NNN983B, C7NNA935C, D2NNN983A, E0NN569KA, E2NNN983A, E0NN569BB, 81826365, 81831205. (Item #: 113625, Ref: D2NNN983AWF)$149.00
Leveling Rod - Leveling Rod and Yoke, Left Hand. For tractor models 5000, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 7910. (Item #: 115635, Ref: C5NNB863C)$49.00
No Picture
Lift Arm - For Ford tractor models 5000, 5100, 5200, 5340, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7700, Replaces Ford OEM number D2NN555E, C7NN555C, C7NN555K, D1NN555B, D1NN555E, Left hand / Right Hand, Category 2, Length: 35" Center to center, Additional Handling and Oversize Fees Apply To This Item, (Item #: 122630)$133.00
Lift Arm - For Ford tractor models 5000, 5600, 5610, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710, Replaces Ford OEM number F0NN555AA11B, 82002013, F0NN555AA, Left hand / Right Hand, Category 2, Length: 37" Center to center, Additional Handling and Oversize Fees Apply To This Item, (Item #: 122631)$180.00
Lower Lift Arm - This lower pull arm is catagory II and can be use on the right or left side. It measures 36 5/8 inches from center of hole to center of hole, 3 15/16 wide and 9/16 inches thick. Replaces D2NN555D, EE8TZ555AA, F0NN555AA, 82023435, 82002013, 81826806. Typically found on models 5000, 5110, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7410, 7610, 7700, 7710, 7740 (Item #: 153318, Ref: D2NN555D)$148.00
Lower Lift Fork Pin - For Ford tractor models 5000, 5600, 5700, 6600, 6700, 7000, 7600, 7700, Replaces Ford OEM number C5NNN939A, 3" Long, (Item #: 113796)$17.90
Lower Lift Link Pin - Replaces original part number 83949240, E4NNF537AA. It uses 390767S36, 1 inch UNF Thread Castle Nut, not included. (Item #: 170281, Ref: E4NNF537AA)$29.40
Pin, Lift Link, Lower - For Ford tractor models 2810, 2910, 3000, 3055, 3230, 3430, 3550, 3900, 3910, 3930, 4000, 4100, 4110, 4200, 4330, 4340, 4410, 4600, 4600SU, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 5200, 5340, 5600, 5610, 5700, 5900, 6000, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, Compatible with Ford Construction and industrial models 420, 515, 532, 535, 3550, 4400, 4500, Replaces Ford OEM number C0NNC893A, 81812094, 3/4" x 2-1/2", (Item #: 170308)$24.30
Rod Leveling - Leveling Rod Assembly, Left Hand, adjustment is 27 inches to 33 inches. For 5000, 5600, 5610, 5700, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. (Item #: 180013, Ref: C5NNB863CWKF)$81.00
Single Chain Assembly - Single Chain Assembly; does not include brackets or u-bolt. For tractor models 5000, 5600, 5610, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. (Item #: 155027, Ref: CFPND936B-LB)$37.00
Stabilizer Pin - For Ford tractor models Major, Power Major, Super Major, 3230, 3430, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4600, 4600SU, 4610, 4630, 4830, 5000, 5030, 5110, 5600, 5610, 5610S, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7410, 7600, 7610, 7700, 7710, 7810, 7810S, 7910, 8210, Replaces Ford OEM number 355278S36, 81824450, 5/8" x 2 3/8", (Item #: 173864)$5.10
Telescopic Bar Hole Stabilizer, Right Hand - For Ford tractor models 600, 700, 2310, 2600, 2610, 2810, 2910, 3310, 3600, 3610, 3900, 3910, 4100, 4110, 4200, 4600, 4610, 5000, 5100, 5110, 5200, 5600, 5610, 5700, 5900, 6000, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8100, 8200, 8210, 8600, 8700, 9200, 9600, 9700, Replaces OEM number FTS15610, Max Length: 28 -3/4", Min Length: 18 -5/16", Additional Handling and Oversize Fees Apply To This Item, (Item #: 169818)$120.00
Top Link Ball End - Cat. II Left Hand threaded repair end. 1 1/4 Inch Left Hand Thread, 1 Inch Ball ID, 13 Inch Overall Length. Replaces DONNA914B, 82001389 (Item #: 168087, Ref: D0NNA914B)$36.95
Top Link Rocker - For 5000 1969 and up, 7000, 5900, (5600, 6600, 6700, 7600, 7700 with Single Speed PTO), (6610, 6710, 6810, 7610, 7710 with 3 Pins). Also Replaces E0NN535CA (Item #: 155001, Ref: C7NN535A)$153.00
Clamp, Double Break-Away, Hydraulic - For use with Pioneer series 4000 and Safeway type S20-4 and S40-4 Couplers. Quik-Cover Assembly HV4957 fits this clamp. Used on tractors with Single Pump Hydraulic System, 1955 thru 1981 models. For tractor models 500, 600, 700, 800, 900, 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 6600. (Item #: 112480, Ref: S42-4)$29.95
Cylinder, Side Link - Side Link Hydraulic Cylinder. (Item #: 178907, Ref: HSL3201)$344.00
Cylinder, Top Link - Top Link Hydraulic Cylinder. (Item #: 167107, Ref: HTL3101)$345.00
Hydraulic Filter - This Spin-on type hydraulic filter measures 3.79 inches outside diameter, 6.42 inches long and 1.125 inches inside diameter hole. VERIFY DIMENSIONS. For tractor models: 4100, 2310 with TANDEM MOUNTED PUMPS 1981 THRU 1983, 2600 with GEAR TYPE PUMPS, 2610 with TANDEM MOUNTED PUMPS 1981 THRU 1983, 3600 with GEAR TYPE PUMPS, 3610 with TANDEM MOUNTED PUMPS 1981 THRU 1983, 3910, 4110, 4600, 4610, 5600, 5610 with VERTICAL EXHAUST, 6600, 6610 with VERTICAL EXHAUST, 6700, 6710 with VERTICAL EXHAUST, 7600, 7610 with VERTICAL EXHAUST, 7700, 7710 with VERTICAL EXHAUST. Replaces 83918631, 81836728, 83901265, 47622189, 83912256, 83903433, D3NNB486B, D4NNB486D, F0NNB486AA, D6NNB486A, D3NNB486A, D8NNB486CA, D8NNB486AA, D4NNB486A, 84263773, 81863229, 81844732, 83984236 (Item #: 125956, Ref: D6NNB486A)$16.30
Hydraulic Filter, Steel Mesh - Steel Mesh Hydraulic Filter replaces OEM number 81802002. Used on 2000, 3000, 4000, 2600, 3600, 3900, 4600, 5600, 6600, 6700, 7600, 7700, 231, 335, 420, 515, 531, 532, 535. Measures 2 3/4 inch tall, 2 1/8 inch Diameter with a 3/4 inch center 3 prong hole. Does not include rubber seals and we do not have them available. YTO C5NNN832B (Item #: 113711, Ref: C5NNN832B)$10.60
Hydraulic Pump - Hydraulic Pump, Gear Type, mounted in Center Housing. For tractor models 5600, 6600, 6700, 7600, 7700. (Item #: 104228, Ref: D8NN600KB)$482.00
Hydraulic Pump - For tractor models 5100, 5600, 5610, 6600, 6610, 6710, 7100, 7600, 7610, 7700, 7710, 7810, 7910, 8210, all with transmission mounted, Gear Type Pump. Also replaces E0NN600AB. Hydraulic Pump. (Item #: 103150, Ref: E0NN600AC)$367.00
Hydraulic Pump - For tractor models 5600, 5700, 6600, 6700, 7600, 7700 all 1975-1981 with transmission mounted Gear Type Pump. (Item #: 104228, Ref: D8NN600KA)$482.00
Hydraulic Pump Gasket - Hydraulic Pump Gasket is used on fits pumps D8NN600KB and D8NN600LB. It replaces original part numbers 83961379, D4NN915A, E7NN915AA (Item #: 156043, Ref: D4NN915A)$12.14
Hydraulic Remote Valve - Single Spool Double Acting Hydraulic Remote Valve Kit is used on 5000, 6600, 7000, 5600, 7600 tractors. Does not work on 10 series or compact tractors. (Item #: 166388, Ref: FDS4447)$260.00
Hydraulic Valve Kit - Valve, Hydraulic, with handle, Single-Spool Multi-Valve. No relief, tandem (4-way) spool, convertible to 3-way, spring center to neutral, with 90 degree rotated handle. Fits Models: 500, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 850, 900, 950, 960, 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 6600. (Item #: 183392, Ref: HV4012)$327.42
Hydraulic Valve Kit - Valve with handles, two-spool, 2000 psi. Relief, one-spool tandem (4-way) float position with spring center to neutral and one spool tandem (4-way) spring center to neutral. Fits Models: 500, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 850, 900, 950, 960, 2000, 2600, 3000, 3600, 4000, 4600, 5000, 5600, 6600. (Item #: 185318, Ref: HV4021)$725.00
Pivot Pin Nut - This Nut is used with D2NNH889A Pivot Pin. Replaces C9NNH891A, 86632551 (Item #: 180243, Ref: C9NNH891A)$0.50
Rock Shaft Bushing - This Rock Shaft Bushing is used on FORD 5000, 5100, 5200, 7000, 7100, 7200, 5600, 6600, 7600, 6700, 7700, 5610, 6610, 7610, 6710, 7710, 5640, 6640, 7740, 7840, 8240, 8340. Associated seal is part number C5NNC944A and is sold separately. Replaces C5NN531A, E2NN531AA, 83933328. (Item #: 170952, Ref: E2NN531AA)$23.10
Rockshaft Seal - This Rockshaft Seal is used with E2NN531AA Bushing. (Item #: 180345, Ref: C5NNC944A)$2.80
Rod Pivot - Pivot for Hydraulic Control Valve Handle. For 2000, 2600, 2610, 3000, 3600, 3610, 4000, 4600, 4610, 500, 5000, 5600, 600, 6600, 700, 800, 900. (Item #: 183852, Ref: C9NND912A)$26.20
Valve Kit, 1 Spool - These kits include Single Spool Valve (Non-Detent/Spring Centering), Hoses, Hose Couplers, Coupler Bracket, Self Closing Dust Covers and Handle Mounting Kit. Valves are current OEM design and bolt to tractor top hydraulic cover in place of accessory plate. Control handles are operated from RH side of operators seat. For tractor models 500, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 850, 900, 950, 960, 2000, 3000, 4000 all 1965 and before. 2000, 3000, 4000, 5000 all 1965-1975. 2600, 3600, 4600, 5600, 6600 all 1975-1981. 2610, 3610, 4610 equipped with single pump hydraulic system, all 1981 and up. (Item #: 180000, Ref: DGPNB950S1-KIT)$954.00
Valve Lever Pivot Pin, Pack of 2 - This Valve Lever Pivot Pin is for factory remote valves. It is used with: C9NNH891A Nut, D3NNB936A Lever and C9NND912A Pivot. Replaces D2NNH889A, 81834237 (Item #: 133463, Ref: D2NNH889A)$11.90
Lights
Headlight Reinforcement Plate - Fits Ford tractors from 1939 and up. (Item #: 111329, Ref: FAA13102A)$9.00
Headlight Ring - Rubber ring is 4 3/4 inches outside diameter and approximately 1 inch wide. Verify OEM part number. For Fords with original Ford fender or cab mounted lights, 1968 and up. Replaces 1027218M1, 83936004, D5NN13N056A, D6NN13N056A (Item #: 155307, Ref: 1027218M1)$8.40
Headlight Switch - Headlight Switch and Nut is used on Ford 2000, 3000, 4000, 5000, 7000, all 1965 to 1975. For 2600, 3600, 4600, 5600, 7600, all 1975 to 1981. For 2310, 2610, 2810, 2910, 3610, 3910, 4110, 4610, all 1981 to 8/1985. For 5110, 5610, 6410, 6610, 6710, 6810, 7610, 7710, all 1981 to 8/1985, 7910, 8210, both 1983 to 8/1985. This is an NON-FUSED replacement. Replaces C5NN11654C, D6NN11N650A, EDPN11654AA. (Item #: 178059, Ref: C5NN11654A)$14.20
Headlight Switch - Headlight Switch and Nut is used on Ford 2000, 3000, 4000, 5000, 7000, all 1965 to 1975. For 2600, 3600, 4600, 5600, 7600, all 1975 to 1981. For 2310, 2610, 2810, 2910, 3610, 3910, 4110, 4610, all 1981 to 8/1985. For 5110, 5610, 6410, 6610, 6710, 6810, 7610, 7710, all 1981 to 8/1985, 7910, 8210, both 1983 to 8/1985. Can use D4NN11666RPL knob, not included. This is a fused switch. Replaces C5NN11654C, D6NN11N650A, EDPN11654AA. (Item #: 121154, Ref: 251405)$16.10
Headlight Washer - Used with light part number 164089AS. Replaces 82858740, 83917547, C5NN13N020B, D8NN13N020AA. For the following tractors: 515, 530, 531, 532, 535, 540, 545, 550, 555, 655, 750, 755, 665, 775, 2600, 2610, 2810, 2910, 6600, 8000, 9000, 3600, 3610, 3910, 4600, 4610, 5600, 5610, 6610, 7600, 7610 (Item #: 154899, Ref: 504781M1)$5.40
LED Lamp, 12 Volt - This LED Floodlight is for 12-volt Negative Ground Systems only. It is polarity specific. It is a direct replacement for 4410, 4411 sealed beam or halogen. Features 6-LED, 1440 Lumens, 18 Watts. 4-1/2 Inch diameter. The flood beam is an excellent work light that illuminates wide and short areas. Replaces 239804, 1164605, 70239804, 71164605, 4410, A42294, A43639, A47179, D33182, L30464, 105774A, 30-3169898, 209495, 251534, C0NN15330A, C5NN13007F, E3NN15330AA, 126470C1, 131203C1, 131348C1, 131508C1, 390756R91, AE31263, AR104119, AR21059, AT25451, H7606, RE285628, RE336111, RE35168, RE561116, 285871M1, 505281M1, 509652M91, 10P2645, 105774A, 166407A, 30-3169898, 735606A (Item #: 127096, Ref: L4411LED)$33.00
Light Bulb, Sealed Beam, 12 Volt - This 12-Volt Sealed Beam has Double Contact. It is 35 Watt. Has a 4.365 inch outside diameter. Used with flat top fenders. Replaces: L4411, 277073, 312555, 80277073. (Item #: 111241, Ref: 373662R91)$9.10
Light Switch Knob - This Light Switch Knob can be used with 251405 light switch or original equipment. Replaces part numbers D4NN11666A, D4NN11666RPLGV, D4NN11666RPL. (Item #: 180202, Ref: D4NN11666RPL)$8.70
Light Switch, Rotary Type - This Rotary Type Light Switch is used on many Ford / New Holland Tractors and Industrials, 1965 and later. It replaces original part numbers C5NN11654A, C5NN11654D, C7NN11654B, C7NN11654C, D5NN11654B, E7NN11654AA, 83959708, D10026500, 83959708, 81818781, 81818408, 83905863. (Item #: 121197, Ref: E7NN11654AA)$13.20
Safety Light Amber - 12 volt amber safety light, 4-1/4 inch diameter, 3/8 inch diameter by 5/8 inch mounting stud. Does not include flasher. Replaces 10A26292, 164177AS, 199954A1, 1K7361F, 248110, 249139, 30-3390705, 3123675R92, 394129R1, 512566M91, 512567M91, 513058M91, 531627R91, 602603ASA, 67538C92, 677540, 70248110, 70249139, A143600, A34853, AA34967, AH164497, AR38456, AR50580, AT22066, AT23467, C5NNA3N359E, D49734, D4NN13N359A, D6NN13N359B, D9NN13N359AA, W164177AS, 130609, L660A-12V, L725-12V, SW02981, TP-AR50580, WN-WL810, 122128 (Item #: 122128, Ref: S.61357)$18.70
Sealed Beam Bulb - This Sealed Beam Bulb is 12 Volt, 40 Watt, 3 Lug Terminal Type. It is 4-1/2 inch diameter. Replaces 83910047, 3072947R91, 3070494R91, K962146, D6NN13N007A, 54051293, 81806938, C5NN13N007A, ATJ8746, 535505M1, K915874 (Item #: 124720, Ref: D6NN13N007A)$27.50
Headliner Retainers - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2600, 3600, 4100, 4600, 5600, 5610, 5700, 6600, 6610, 6700, 6710, 7600, 7610, 7700, 7710, 7810, 7910, 8210, 8700, 9700, Compatible with Ford Construction and industrial models 233, 333, 16 Pack, (Item #: 172200)$34.00
Hydraulic Lift Cylinder Piston - For Ford tractor models 5000, 5100 (1975-12/31/76), 5200 (1975-12/31/76), 5340 (1975-12/31/76), 5600 (1975-12/31/76), 5700 (1975-12/31/76), 6600 (1975-12/31/76), 6700 (1975-12/31/76), 7000, 7200 (1975-12/31/76), 7600 (1975-12/31/76), 7700 (1975-12/31/76), Replaces Ford OEM number C5NN530C, D3NN530D, Diameter: 3.75", For lift cylinder O-ring use Item #: 140609, (Item #: 155013)$25.98
Hydraulic Shaft - For Ford tractor models 5000, 5100, 5110, 5200, 5340, 5600, 5700, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7700, 7710, 7810, 7910, 8210, Replaces Ford OEM number 81801593, C5NN544B, (Item #: 119855)$123.00
Lift Arm - Left - For Ford tractor models 5000, 5100, 5200, 5340, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7700, Replaces Ford OEM number C5NN839F, E3NN839AA, (Item #: 154997)$104.00
Lift Arm - Right - For Ford tractor models 5000, 5100, 5200, 5340, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7700, Replaces Ford OEM number C5NN838F, E3NN838AA, (Item #: 154995)$108.58
No Picture
Weather Strip Seal Kit - Side Window - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 3600, 4600, 4610, 5600, 5610, 6600, 6610, 6700, 6710, 7600, 7610, 7700, 7710, 8210, 8630, 8700, 8730, 8830, 9700, Replaces Ford OEM number D8NN9429732BC, D8NN9429732BB, D8NN9429733BC, Replaces OEM number 83947573, D8NN9429733BB, 83947572, Sold as a pair, Right and Left Hand side windows, Weather Seal must be glued in., (Item #: 170442)$303.48
No Picture
Weather Strip Seal - Rear Glass Molding Kit - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 5110, 5600, 5610, 5700, 6600, 6610, 6700, 6710, 6810, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8210, 8530, 8630, 8700, 8730, 8830, 9000, 9700, Replaces Ford OEM number E7NN9442082AA, 83961300, D8NN9442082GC, For Sliding/American Style Rear Glass, Length: 159", Molding makes full circle, Molding must be glued in, (Item #: 170491)$225.00
Ford, C7NN6A605A, 81817359, Used - For Ford tractor models TW5, TW10, 2000, 2100, 2110, 2120, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 3330, 3400, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4140, 4190, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4610, 4610SU, 4830, 5000, 5030, 5100, 5190, 5200, 5340, 5550, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7600, 7610, 7700, 7710, 7810, 7910, 8210, 8600, 8700, 9000, 9200, 9600, 9700, Compatible with Ford Construction and industrial models A62, A64, A66, 230A, 231, 233, 234, 250C, 333, 334, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445C, 445D, 455C, 455D, 515, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 650, 655, 655A, 655C, 655D, 675D, 750, 755, 755A, 755B, 5500, 6500, 7500, Compatible with Ford Engine(s) 158, 175, 192, 201, 233, 256, 268, 401 Replaces Ford OEM number C7NN6A605A, 81817359, C7NN6A605, , Compatible with New Holland Skid Steer Loader(s) L783, L785, LS180, Compatible with New Holland Hay Cutting(s) 907, 909, 910, 912, 1100, 1112, 1114, 1118, 1495, 1499, For a new version of this item use Item #: 169650, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 444465)$6.01
Oil Dipstick - This Dipstick is 7 7/8 inches long. It is used on many Ford agriculture and industrial models, 1975 and later. Replaces: 87801534, C7NN6750C, C9NN6750A, D3NN6750C, D3NN6750D, D3NN6750E, D4NN6750B, D4NN6750D, D6NN6750B, E9NN6750BA, 81816867, 81822073, 81837146, 81837147, 81843818, 83902286, 83905287, 83918846, 83982499 (Item #: 113916, Ref: E9NN6750BA)$8.80
Oil Pressure Switch - This oil pressure switch is made with 2 types of connectors and you may receive a typical space connector or a round connector. Whichever wire connector you have on your tractor will fit either switch. The are interchangeable. For tractor models 2000, 3000, 4000, 5000, 7000, 8000, 8600, 8700, 9000, 9600, 9700, 2600, 3600, 3900, 4100, 4600, 5600, 5900, 6600, 6700, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4110, 4610, 5610, 5610S, 6610, 6610S, 6710, 6810, 7610, 7610S, 7710, 7810, 7810S, 7910, 8010, 8210, 3230, 3430, 3930, 4130, 4630, 4830. Replaces 81873524, F1NN9278AA, D8NN9278AA. (Item #: 153774, Ref: D8NN9278BD)$7.87
Clutch Pack Assembly, Independent PTO - Includes 4 Discs and 4 Plates. For tractor models: 5000, 5600, 5900, 6600, 7000, 7600, 7700. Note, on 5000 and 7000, when switching from 3 disc to 4 disc assembly, you will also need change your hub to E0NNN750AA. (Item #: 178948, Ref: D2NNN751D)$267.00
Dual Power/ PTO Disc - This Dual Power/PTO Disc measures 5.84 inches outside diameter, 4.500 inside diameter with 52 teeth. It replaces original part numbers C9NNP743A, C9NNP743D, D3NNP743A, 81822308, 81830023, 81830026. (Item #: 109833, Ref: C9NNP743D)$13.60
Idler Gear Support - Hydraulic Pump Idler Gear Support part number C7NN7049D has a 2.999 inch bearing outside diameter. The tube is 2.060 inches in length. It is used on the following, all 01/01/1965 through 04/30/1971: 5000, 5100, 5200, 7000, 7100, 7200, 5600, 6600, 7600, 6700, 7700, 5610, 6610, 7610, 6710, 7710 It replaces original part number C7NN7049D C7NN7N085B, D9NN7N087A. (Item #: 179989, Ref: C7NN7049D)$46.00
Idler Gear Support - Hydraulic Pump Idler Gear Support part number C7NN7049D has a 2.890 inch Bearing outside diameter. The tube is 1.610 inches in length. This is used on (5000, 5100, 5200, 7000, 7100, 7200, All 05/01/1971 and up) 5600, 6600, 7600, 6700, 7700, 5610, 6610, 7610, 6710, 7710. Replaces C9NN7049C. (Item #: 170969, Ref: C9NN7049C)$84.00
Oil Seal, PTO Input Shaft - This PTO Input Shaft Oil Seal measures 1.125 inch inside diameter, 1.565 inch outside diameter, 0.250 inch wide. For models 5000, 5600, 5610, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 8000, 8600, 8700, 9000, 9600, 9700. All for tractors with a 7 or 8 speed transmission. Replaces 81801990, C5NN2N258A, C5NN2N258C, C5NN799A, C5NNE2A258B. (Item #: 165141, Ref: 195501M1)$5.15
PTO Cap - This PTO Cap is 4 inches long. It will not work on 5 inch PTO shafts. It has 65mm outside threads. It replaces OEM numbers: C5NN726B C5NN726A, SBA378110020, 81801856, 47811118 (Item #: 155020, Ref: C5NN726A)$22.10
PTO Clutch Pack Sealing Ring - This PTO Clutch Pack Sealing Ring is used with D2NNN751D and E0NNN751BA Clutch Packs. 2.375 Inch Outside Diameter. Three used per tractor. Replaces 8313283, 81809513 and 313283. (Item #: 168315, Ref: 313283)$4.10
PTO Clutch Plate - This is a Steel PTO Clutch Plate. It measures 6.062 inches outside diameter, 4.448 inch inside diameter and has 60 teeth. It replaces original part numbers 81808607, D6NNC730A, PBB77573A, PBB77573AA, 1102-5506, 81565601. (Item #: 104211, Ref: PBB77573A)$5.30
PTO Drive Clutch Housing - Is some applications require replacing OE C9NN7R007A with OE D5NN7R007A when used with single speed PTO. Used on 3600, 4600, 5000, 5100, 5110, 5190, 5200, 532, 5340, 5600, 5700, 5900, 6600, 6700, 7000, 7100, 7200, 7600, 7700. This part replaces Ford New Holland part numbers: D5NNN707A, D5NNN07A, 83903939, 81827131 (Item #: 151874, Ref: D5NNN707A)$255.00
PTO Drive Clutch Hub - For 5700, 5900, 6410, 6810, 7410, 7810, 7910, 8210, (5000, 7000, both 1965 and up with Single/Two Speed), (5600, 5610, 6600, 6610, 6700, 6710, 7600, 7610, 7700, 7710, all with Single/Two Speed). PTO Drive Clutch Hub replaces D2NNN750A. For tractor models with 8 or 10 Plate Independent PTO Clutch. 25 teeth and 52 teeth. (Item #: 165269, Ref: E0NNN750AA)$135.00
PTO Friction Disc - PTO Friction Disc with Internal Splines. Used on PTO with 2-Speed Transmission. For tractor models 5000, 7000 (6/1973-1975), 5600, 5700, 6600, 6700, 7600 (single and 2-speed, 1975-1981). (Item #: 109833, Ref: D3NNP743A)$13.60
PTO Output Cover Gasket - Used on many Ford / New Holland Tractors built 1965 and later. Replaces OEM part numbers C5NN7086A, 81815558 (Item #: 179414, Ref: C5NN7086A)$4.10
PTO Output Shaft Seal - Note that two size seals were used on the output shaft on many of the models listed. Verify measurements or OEM number before ordering. This seal measures 74.62mm inside diameter x 95.24mm outside diameter x 9.5mm wide (3.75 inches x 2.85 inches x 0.375 inches wide). Used on Ford 3600, 4600, 5000, 5100, 5110, 5190, 5200, 532, 5340, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8010, 8210, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9600, 9700, TW10, TW15, TW20, TW25, TW30, TW35, TW5. Replaces Ford / New Holland part numbers D9NNN710BB, D9NNN710B, 83944032 (Item #: 189274, Ref: D9NNN710B)$12.80
PTO Output Shaft Seal - Note that two size seals were used on the output shaft on many of the models listed. Verify measurements or OEM number before ordering. This seal measures 74.6mm inside diameter x 95.6 outside diameter x 12.5mm wide (3.75 inches x 2.85 inches x 0.56 inches wide). Used on Ford / New Holland 3600, 4600, 5110, 532, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 6810S, 7010, 7410, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8200, 8210, 8240, 8340, 8530, 8600, 8630, 8670, 8670A, 8700, 8730, 8770, 8770A, 8830, 8870, 8870A, 8970, 8970A, 9200, 9700, TS100, TS100 Brazilian, TS110, TS110 Brazilian, TS115, TS120 Brazilian, TS80, TS90, TV140, TW10, TW15, TW20, TW25, TW30, TW35, TW5. Replaces 81819768, 83955173, 9823545, 89823545, D9NNN710BC, D9NN710BC (Item #: 128143, Ref: 9823545)$27.70
PTO Piston O-Ring - This is the Inner PTO Piston O-Ring Seal. Replaces 373227S 83416992. (Item #: 172963, Ref: 373227S)$1.90
PTO Piston O-Ring - This is the Outer PTO Piston O-Ring Seal. It replaces C0NN7A548A, CFPN6333A/B, 81805281 (Item #: 172955, Ref: C0NN7A548A)$4.40
PTO Piston Return Spring - Replacing Ford / New Holland part numbers 81871420, 83935173, C0NN7C151A, 9823824, D7NNC732A, 81804819, this Spring is used in tractors with independent PTOs. Used on Ford / New Holland models: 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7410, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8000, 8010, 8210, 8240, 8340, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9600, 9700, TS100, TS90, TW10, TW15, TW20, TW25, TW30, TW35, TW5 (Item #: 124549, Ref: D7NNC732A)$20.50
PTO Shaft - For tractor models (5100, 5200, 7100, 7200, all with 2 Speed after 6/1973), (8000, 9000, both with 2 speed 1968-1978), (5600, 5700, 6600, 6700, 7600, 7700, all with 2 speed after 1975). PTO Shaft 540 RPM. 11.475 inches Long. 36 and 38 tooth splines. (Item #: 109834, Ref: D2NNB728A)$95.00
PTO Shaft - For tractor models (5100, 5200, 7100, 7200, all with 2 speed after 6/1973), (8000, 9000, both with 2 speed 1968-1978), (5600, 5700, 6600, 6700, 7600 both with 2 speed 1975 and later). PTO Shaft 1000 RPM. 11.475 inches long, 38 tooth splines on tractor side, 21 splines on implement side. Replaces D2NNB728B, C7NNB728E, 81827171 (Item #: 110628, Ref: D2NNB728B)$222.00
PTO Shaft - For tractor models (5110, 5610, 5900, 6410, 5410 UK, 6610, 6710, 6810, 7610, 7710, all with single speed PTO 10/1989 and later), (5640, 6650, 7740 all with single speed 11/1990 and later). PTO Shaft 540 RPM. 11.764 inches long, 28 tooth drive splines. (Item #: 111990, Ref: E8NN710AA)$336.00
PTO Shaft - For 5100, 5110, 5600, 5610, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7100, 7200, 7600, 7610, 7700, 7710, all less sync trans. PTO Shaft 39.87 inches long, 20 and 25 spline. (Item #: 111991, Ref: E1NN7A684AB)$176.80
PTO Shaft, Rear Lower - This PTO shaft measures 12.03 inches in length and has 29 splines. It is for Single-Speed 540 RPM Independent PTO Drive Shaft. Tractors: 5000, 7000 (6/1973-1975), 5600, 5700, 6600, 6700, 7600, 7700 (1975-1981), 5610, 6610, 6710, 7610, 7710 (1981-9/1989), 5610S, 6610S, 7610S (1/1994-12/1994). Replaces D2NNN752B, E3NNN752AA. (Item #: 129295, Ref: E4NNN752AA)$99.00
PTO Shaft Seal - This new PTO Shaft Seal fits the following tractors with single speed PTO's: 5000, 5600, 5610, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7600, 7610, 7700, 7710. It has an inside diameter of 1.42 inches (36.07 mm), outside diameter of 2.5 inches (63.65 mm) and a thickness of 0.30 inch (7.84 mm). It replaces original part numbers C5NN701B, C5NN710B, C5NNN710A, C5NNN710B, D9NNN710CA, D9NNN710DA, 81819064. (Item #: 164442, Ref: C5NN710B)$4.80
PTO Shaft Support - Support, for PTO Shaft and Drive Clutch Valve. DOES NOT have relief oil hole in support. For tractor models 5000, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. Replaces original part numbers C2NNN776A, D2NNN776A and 81826819. (Item #: 111897, Ref: D2NNN776A)$22.80
Suspension Seat - New Ford/New Holland replacement seat. Complete seat with suspension, blue. Fits Ford / New Holland Compact tractor models: 1110, 1210, 1310, 1510, 1710, 1910; Fits Industrial/Construction models: 340A, 340B, 345D, 3500, 445, 445A, 445C, 445D, 450, 515, 540A, 540B, 545A, 545C, 545D; Tractor models: 2100, 2110, 2120, 2150, 2300, 231, 2310, 234, 2600, 2810, 2910, 3000, 3055, 3100 3300, 3310, 3330, 3600, 3610, 3910, 4000, 4100, 4110, 4200, 4330, 4340, 4400, 4410, 4600, 4610, 5000, 5100, 5200, 531, 532, 5600, 5900, 6600, 6700, 7000, 7100, 7200. There is a plate on the bottom that is 4 inches wide and 8 1/4 inches long. In the center of this plate are 2 slots that are 3/8 inches wide, 1/4 inch from each edge and 1/2 inch apart and they are about 4 inches long. Overall width is 19.5 inches, overall length of base is 15.25 inches, overall height of base is 9.25 inches. (Item #: 101226, Ref: CSA698-8V)$227.00
Fender Bracket LH/RH - For 2810, 2910, 3910, 4600, 4610, 4630, 4830, 5030, 5600, 5610, 6600, 6610, 7600, 7610. Fender Bracket for Left or Right Side (price is for each). Add $10 extra for shipping each piece due to weight of 32 pounds each. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 112023, Ref: D3NN16N319C)$179.00
Fender, LH - Flat Top. For tractor models 2600, 2610, 2810, 2910, 335, 3600, 3610, 3910, 3930, 4100, 4110, 420, 4600, 4600SU, 4610, 4610SU, 4630, 4830, 5030, 515, 532, 535, 5600, 5610, 6600, 6610, 7600, 7610. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Ships freight (Item #: 105559, Ref: E5NN16313DA)$240.00
Fender, RH - Flat Top. For tractor models 2600, 2610, 2810, 2910, 335, 3600, 3610, 3910, 3930, 4100, 4110, 420, 4600, 4600SU, 4610, 4610SU, 4630, 4830, 5030, 515, 532, 535, 5600, 5610, 6600, 6610, 7600, 7610. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 105558, Ref: D8NN16312ABB)$240.00
Front Bumper - Axle Mount - High quality bumper with mounting brackets. Mounts to axle. Blue. (Item #: 113401, Ref: D8NN17750AA)$317.27
Front Bumper - Frame Mount - For Ford tractor models 4000, 4500, 5000, 5100, 5600, 5610, 6600, 6610, 7100, 7600, 7610, Replaces Ford OEM number C5NN17750C, 8391579, 87045743, Frame mount, Measurements 21-1/8 " inside bracket to inside bracket, Bolt Hole Pattern 4 " on C to C, Comes primered (color may vary). Prior to painting check fitment, Additional Handling and Oversize Fees Apply To This Item, (Item #: 109631)$139.98
Front Shell - Front Cap Shell Assembly For 4600, 5600, 6600, 515 - Oil Bath Breather Type - Right Side Hole for Air Cleaner. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 164194, Ref: D5NN8N202A)$312.00
Grill - One Piece Grill with holes for lights for 1968 and up. Measures 18 1/2 inches wide and 23 3/4 inches tall. (Item #: 111518, Ref: D5NN8200C)$40.00
Grill Screen - Metal Grill Screen for 2000, 2600, 3000, 3600, 4100, 4140, 4600, 4600SU, 5200, 5600, 5900, 6600, 7200, 7600, 231, 531, 532. One piece plastic construction like original. Grill screw clips (2 needed on most applications) available as S.60436. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 104063, Ref: D5NN8200A-OEM)$37.00
Grill Screen Clip - For tractor models 2000, 2600, 3000, 3600, 4100, 4140, 4600, 4600SU, 5200, 5600, 5900, 6600, 7200, 7600, 231, 531, 532 (2 needed on most applications). Please verify quantity needed from your tractor. Replaces 45264S2, C9NN8B151B, D4NN8N213A, 83901581 (Item #: 118786, Ref: S.60436)$5.80
Grill Screen Clip - This Grill Clip fits the following tractor models: 2000, 3000, 4000, 5000, 5600, 6600, 7000, and 7600. Replaces part numbers: 81816917 and C7NN8A067A. (Item #: 163166, Ref: C7NN8A067A)$2.00
Hood - Hood Panel, engine left hand side, Vertical Exhaust, without cab. 41 3/4 inches long. For 5100, 5110, 5600, 5610, 5900, 6400, 6410, 6600, 6610, 7100, 7600, 7610. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 155812, Ref: D5NN16626B)$77.00
Hood Handle - Handle Assembly, engine hood right hand side. For 2000, 231, 2310, 233, 2600, 2610, 2810, 2910, 3000, 3230, 333, 335, 3430, 3600, 3610, 3900, 3930, 4000, 4110, 4140, 420, 4600, 4610, 4830, 5000, 5030, 515, 531, 532, 535, 5600, 5610, 5910, 6600, 6610, 7000, 7600, 7610. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Replaces C5NN16N644B, D6NN16N644A, 83909243. (Item #: 113917, Ref: D6NN16N644A)$8.80
Hood Hinge - THESE FIT AFTERMARKET HOODS ONLY. These will NOT work for original hoods. Replaces 81811486, C5NN16N631B, C9NN16N631A (Item #: 179348, Ref: C5NN16N631B)$19.60
Hood Prop Rod - This hood prop rod is 17 1/2 inches and used on 2000, 3000, 4000, 4000SU, 5000, 7000, 2600, 3600, 4600, 4600SU, 5600, 6600, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4610SU, 5610, 6610, 7610, 7810, 5900, 231, 335, 531, 340, 540, 3400, 3500, 445, 4500, 250C, 340, 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 540, 540A, 540B, 545, 545A, 545C, 545D. It Replaces original part number C7NN8042A. (Item #: 178161, Ref: C7NN8042A)$9.22
Hood, RH - 41.750 inches long. For tractor models 5100, 5600, 6600, 7100, 7600. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 155815, Ref: D5NN16N768B)$92.00
Instrument Panel - For tractor models 2310, 2600V, 4110, 420, 4400, 4410, 445, 4500, 4610SU, 5100, 5110, 515, 531, 532, 535, 540, 540A, 545, 5600, 5610, 5900, 6600, 6610, 6810, 7100, 7600, 7610, (2110 from 1965 to 1975). Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 172723, Ref: D8NN16948DB)$260.00
Instrument Panel - Fits 2000, 3000, 4000, 5000, 7000, 5900, 2600, 3600, 3900, 4100, 4600, 5600, 6600, 7600, 2310, 2610, 2810, 2910, 3610, 4110, 4610, 5610, 6610, 7610, 230A 231, 334, 335, 340A, B, 420, 445A, 450, 515, 530A, 531, 535, 540A, B, 545A (less Select-o-speed, Dual Power, Cab, Torque Converter). Replaces D0NN16N627R and D8NN16948DB. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 172723, Ref: D0NN16N627R)$260.00
No Picture
Radiator Shell Cowling - This Radiator Shell Cowling is for models (4000, 5000 after 1986), 5600 and 6600. Uses Grill D5NN8200A-OEM. (Item #: 104061, Ref: D4NN8N202M)$404.52
No Picture
Radiator Shell Cowling - This Radiator Shell Cowling is for models (4000, 5000 after 1986), 5600 and 6600. Uses Grill D5NN8200A-OEM. (Item #: 104061, Ref: D4NN8N202M)$404.52
Rubber Hood Pads - For all models after 1965 with Front Cowling that surrounds the Grill/Radiator. These rubber pads fit onto cowling under hood. Models: 231, 233, 333, 515, 2000, 2600, 3000, 3600, 3900, 4000, 4100, 4110, 4600, 4600SU, 5000, 5600, 6600, 7000. Replaces C5NN16N655B, C5NN16N655A. (Item #: 113797, Ref: C5NN16N655B)$1.20
Running Board, LH - 20.5 inches long, 8.5 inches wide. For tractor models 2000, 2600, 3000, 3600, 5600, 6600, 7600. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 122145, Ref: D3NN16451D)$73.00
Running Board, RH - 20.5 inches inches long, 8.5 inches wide. Replaces D4NN16472B. For tractor models: 2000, 2600, 3000, 3600, 5600, 6600, 7600. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 122146, Ref: D5NN16472C)$80.00
Steering Sector Cover - For Ford tractor models 3120, 4000, 5100, 5600, 6600, 7100, 7600, Replaces Ford OEM number C7NN3R654A, 81822068, Comes primered (color may vary). Prior to painting check fitment, sanding and skim coat may be needed, (Item #: 159308)$95.00
Wheel Weight, Rear - For Ford tractor models TW5, TW15, 2810, 2910, 3000, 3600, 3910, 4000, 4600, 4610, 5000, 5600, 6600, 6610, 7600, 7610, 7710, 7810, Compatible with New Holland tractor models 7010, 8010, Replaces New Holland OEM number 82004206, 820026905, 82029581, OD: 18-3/8 ", ID: 10-1/8 ", Thickness: 2-3/8 ", Weight: 100 lbs each, Hole Pattern: 3 @ 10-3/4", Item ships via freight carrier please call 1-800-853-2651 for a freight quote, (Item #: 128842)$168.00
Steering
Axle Carrier Housing, LH - Used on ZF Axle APL1351. This left side hub carrier replaces OEM numbers L35603, P4468358031, 3230954R1, 83953218. Verify axle number before ordering. Used on Ford models: 5600, 5700, 6600, 6700 (Item #: 124660, Ref: L35603)$250.00
Axle Carrier Housing, RH - Used on ZF Axle APL1351. This right side hub carrier replaces OEM numbers L35604, ZP4468358032, 3230955R1, 83953219, ZP1927585. Verify axle number before ordering. Used on Ford models: 5600, 5700, 6600, 6700 (Item #: 124661, Ref: L35604)$243.00
Axle Knee, Left Hand - This is a Left Hand Axle Knee used on Ford 5000, 7000, 5600, 6600, 7600, 5610, 6610, 7610. It replaces original part number C5NN3007A (Item #: 169481, Ref: C5NN3007A)$273.00
Axle Knee, Right Hand - This is a Right Hand Axle Knee used on Ford 5000, 7000, 5600, 6600, 7600, 5610, 6610, 7610. It replaces original part number C5NN3006A (Item #: 192769, Ref: C5NN3006A)$345.65
Axle Pin, Front - This Heavy Duty Front Axle Pin is threaded. 1.750 inch outside diameter, 4.71 inch long, 4.00 inch usable length. For the following models built after 7/1958: 601, 701, 801, 901, 2000, 2100, 2600, 2610, 2810, 2910, 3100, 3600, 3610, 3910, 4000, 4100, 4110, 4600, 4610, 5100, 5600, 5610, 6600, 6610, 7100, 7600, 7610. Uses C5NN3128B Flange. (Item #: 172932, Ref: 312659)$101.00
Axle Pin Locking Plate - This locking plate is used with 312659 Pin. Replaces C5NN3128B. (Item #: 153968, Ref: C5NN3128B)$12.00
Axle Pivot Pin Bushing - For Ford tractor models TW10, TW20, TW30, 3500, 4400, 5000, 5100, 5110, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7100, 7600, 7610, 7700, 7710, 7740, 8000, 8240, 8340, 8600, 8700, 9000, 9600, 9700, Compatible with Ford Construction and industrial models 3550, Replaces Ford OEM number C5NN3446A, 81802940, 81941357, 1.50" O.D., 1.247" I.D., 1.375" Long, Rear Bushing, (Item #: 111730)$3.80
Axle Shaft - Used in ZF Mechanical Four Wheel Drive axles, this part replaces AL33349, ZP1927860, 1502272C1, 3232082R91, 81927860. (Item #: 124723, Ref: AL33349)$249.00
Axle Shaft and Yoke, MFWD - Used on ZF APL1351 Mechanical Four Wheel Drive front end, this shaft is 9.39 inches long with 21 teeth. Replaces OEM numbers 3216599R91, 81927571, AL32883, ZP1927571. Ford models: 5600, 5700, 6600, 6700 (Item #: 115716, Ref: AL32883)$159.00
Axle Shaft with Yoke - Used on ZF APL351 Mechanical Four Wheel Drive front ends, this shaft and yoke is 35.50 inches from center of the u-joint to the end. It has 21 teeth. This part replaces OEM numbers ZP1927573, 3230278R1, AL32884. Ford models: 5600, 5700, 6600, 6700 (Item #: 160162, Ref: AL32884)$338.00
Ball Bearing Assembly - The is an open, deep groove bearing. It has applications in transmissions as well and is CAR MFWD front ends. It measures: 60mm (2.362 inches) inside diameter, 110mm (4.33 inches) outside diameter, 22mm (0.866 inches) wide. Replaces manufacturer part numbers: 6212, 32306, ST269A, 3114946R91, K261879, 83930318, 20141040, CAR25813, 28996590, C5NN7127B, 81804781, 80996590, 20140, 253072272, 8101-06212, 1440545X1, 24101-62124, 971043 (Item #: 156046, Ref: C5NN7127B)$16.98
Ball Bearing, Steering Gear - Used with E1ADKN3556 Ball Race. 14 used for main nut, 10 used in upper shaft bearing, 10 used in lower shaft bearing. For tractor models Major, Super Major, 2600, 2610, 3600, 3610, 4000, 4100, 4110, 4600, 4610, 5000, 5600, 5610, 6600, 6610, 7000, 7600. Replaces 353075S. (Item #: 167684, Ref: 83424343)$0.50
Bushing - Bushing Assembly, Upper. For tractor models 2600, 3600, 4100, 4600 (4/1976-1981); 5600, 6600, 7600 with manual steering (4/1976-1981);2610, 3610, 4110, 4610, 5610, 6610, 7610 with power steering (1981-3/1985).D5NN3517A (Item #: 114044, Ref: C5NN3517A)$6.20
Bushing - Bushing, 1.375 long. For Power Steering Center Arm Pivot Shaft, Upper Bushing. For tractor models 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. (Item #: 153967, Ref: C5NN3179B)$4.10
Bushing - Steering Rocker Shaft - For Ford tractor models Super Major, 2000, 2600, 3000, 3600, 5100, 5110, 5600, 5610, 5900, 6410, 6610, 7100, Replaces Ford OEM number C5NN3N652A, E27N3109A, E27N3110A, 81717388, 81717391, 81803198, 81803202, 87295840, O.D.: 1.625", I.D.: 1.498", Length: 2.0", (Item #: 146687)$8.90
Center Arm - Center Arm, for Power Steering Pivot Shaft. For tractor models 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. (Item #: 100667, Ref: D6NN3N670A)$82.00
Drag Link - Drag Link for power steering, 50.50 inch center post to center post. For 5000, 5600, 6600, 7000, 7600. Replaces C7NN3304B, E0NN3308CA, 81822052, 83925158. (Item #: 100689, Ref: E0NN3304CA)$66.00
Drag Link End - Front - For Ford tractor models 5000, 5100, 5600, 5610, 6410, 6600, 6610 (81 with manual steering), 7000 (68 - 75), 7100 (with manual steering), 7600 (75 - 81 with manual steering), Replaces Ford OEM number C7NN3A300A, 81825395, 877554825, C5NN3A300D, Front Drag Link End, Length 7.875", Diameter .935", (Item #: 104617)$32.00
Drag Link End - Rear - For Ford tractor models 3430, 3930, 4610, 4630, 4830, 5030, 5600, 6600, 7600 (All with Power Steering), Replaces Ford OEM number E1NN3307AA, 83932651, Diameter 1.125", Length 41.190" from center of ball stud to end of tube, (Item #: 104588)$67.00
Drag Link End - Rear - For Ford tractor models 5000 (65-75 replacement thread style link used 65-12/67), 5100 (with manual steering), 5600 (71-81 with manual steering), 5610 (81 with manual steering), 6410 (with manual steering), 6600 (71-81 with manual steering), 6610 (81 with manual steering), 7000 (65-75 replacement thread style link used 65-12/67), 7100 (with manual steering), 7600 (71-81 with manual steering), Replaces Ford OEM number C7NN3304C, C5NN3304T, Length 47.500" long from center of ball joint to end, (Item #: 104615)$133.00
Drag Link End - Rear - For Ford tractor models 5000 (68-75 and 65-12/67 when replacing non thread link), 5100 (with manual steering), 5600 (75-81 with manual steering), 5610 (81 with manual steering), 6410 (with manual steering), 6610 (81 with manual steering), 7000 (68-75 and 65-12/67 when replacing non thread link), 7100 (with manual steering), 7600 (75-81 with manual steering), 7610 (with manual steering), Replaces Ford OEM number C5NN3307N, C7NN3307B, Rear Drag Link End, Length 47.500", (Item #: 104619)$72.87
Drop Arm - For Ford tractor models 5000, 5600, 5610, 5900, 6600, 6610, 7000, 7600, 7610, Replaces Ford OEM number C7NN3590B, 81822063, (Item #: 154911)$102.00
Front Axle Bushing - This Front Axle Pin Bushing is used on 5000, 5100, 7000, 7100, 5600, 6600, 7600, 5610, 6610, 7610, 8000, 9000, 8600, 9600, 9700, TW5, TW10, TW15, TW20, TW25, TW30, TW35, 3500, 4400. It has a 2.132 inch outside diameter, a 1.893 inch inside diameter and is 2 inches long. It replaces original part number C5NN3153A (Item #: 111728, Ref: C5NN3153A)$6.40
Front Axle Pin, Front - Front Axle Pin, Manual or Power Steering. For tractor models 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. (Item #: 162989, Ref: C5NN3N159A)$34.90
Front Axle Pin, Rear - 1.250 inch outside diameter, 5.150 inches long, Manual or Power Steering. For tractor models 3550, 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. Replaces C5NN3N160A, 81802839, 81802839GV, E6NN3N160AA (Item #: 128484, Ref: C5NN3N160A)$28.80
Front Axle Support - For models: (5000 from 9/1970 and up), 7000, 5600, 5900, 6600, 7600, 5610, 6610, 7610. Steering Shaft Bushings (C5NN3179B and C5NN3179A) not included. Replaces Part Numbers E5NN3029BA D0NN3029A. (Item #: 153934, Ref: E5NN3029BA)$940.00
No Picture
Hydraulic Lift Cylinder Piston Ring - For Ford tractor models 5000, 5600, 5700, 6600, 6700, 7000, 7600, 7700, Replaces Ford OEM number D1NN473B, Piston Diameter: 3.75", (Item #: 176453)$5.10
Pitman Arm - This Steering Pitman Arm is used on manual and power steering gear boxes with a single drop arm. It has 36 splines and replaces original part numbers C5NN3590A and 81803153. For tractor models 2310, 2610, 2910, 3430, 3610, 3910, 3930, 4110, 4130, 4600, 4610, 4630, 4830, 5030, 535, 5100, 5110, 5600, 5610, 6600, 6610 and 7600. (Item #: 104740, Ref: C5NN3590A)$189.54
Power Steering Control Valve Housing - This Power Steering Control Valve Housing is used on Ford Models: 5000, 7000, 5600, 6600, 7600. It replaces original part number C9NN3C516B (Item #: 180253, Ref: C9NN3C516B)$125.00
Power Steering Cylinder End - Power Steering End right hand (inner), .875 inch-14 thread female, 3.625 inches long to center of post. Tractors: 3010S, 4010S, 5100, 5110, 5600, 5610, 5610S, 5900, 6410, 6600, 6610, 6610S, 6710, 6810, 6810S, 7010, 7100, 7600, 7610, 7610S, 7810, 7810S, 8010. Verify Part number to ensure proper fit. (Item #: 100683, Ref: E3NN3B539AA)$33.00
Power Steering Hose Assembly - Flexible Power Steering Hose designed to replace rigid Ford tube assemblies. 54 inches long, 3/8 inch inside diameter. SAE 100 R1A single wire braid hose with 5/8 inch-18 thread, straight SAE flare female swivel on one end, 5/8 inch-18 thread SAE straight inverted flare on other. For tractor models 2000, 2600, 3000, 3500, 3600, 4000, 4600, 5000, 5600, 6600, 7000, 7600. Can replace tube assemblies C5NN3A562C, C7NN3A562C, C5NN3A541A, C7NN3A541A, C7NN3A541B, D0NN3A562A. (Item #: 178207, Ref: FPH54)$63.00
No Picture
Power Steering Hydraulic Pump - For Ford tractor models 2000, 2100, 2110, 2120, 2150, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3150, 3400, 3500, 3550, 3600, 3610, 3900, 3910, 4000, 4100, 4110, 4140, 4330, 4340, 4400, 4410, 4600, 4600SU, 4610, 4610SU, 5000, 5100, 5200, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7700, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 333, 334, 335, 420, 515, 530A, 531, 532, Replaces Ford OEM number D7NN3A674B, E6NN3K514DA, 83959532, Front inlet hole size: 9/16" UNF, Front outlet hole size: 5/8" UNF, Inner maximum liters per minute: 12.5, Inner maximum gallon per minute: 2.75, Top hole spacing: 107, (Item #: 170931)$522.48
Power Steering Pump - This power steering pump used with flair fitting on models using Steering Gear Box, pump has Relief Valve. For tractor models 2310, 234, 2610, 2810, 2910, 3230, 334, 335, 3430, 3910, 3930, 4100, 4110, 4130, 4600, 4610, 4630, 4830, 5030, 5100, 5600, 5610, 5900, 6600, 6610, 6710, 7100, 7600, 7610, 7710. Rated Pressure 725-1305 at 500-2000rpm. Safety valve Opening Pressure 942-1087 PSI, Safety Valve Full Open: 1087-1305 PSI. Unit designed for o-ring fitting, not supplied w/pump. This pump fits tractors with JIC fittings. Replaces 82858430, E6NN3K514PA99M (Item #: 113208, Ref: E6NN3K514PA99M)$262.00
Power Steering Pump - This Power Steering Pump replaces pumps with an internal Relief Valve (will not replace external relief valve. For 3500, 3550 5/1970 and up, 5100, 7100 7/1970 and up, 4100 4/1970 and up, 4600, 5600, 6600, 7600 5/1981 and up, 5610, 6610, 7610 4/1985 and up. Power Steering Pump with reservoir. Pressure relief valves set at 1100 PSI, 2.74 GPM. This pump can replace: 83949432, E6NN3K514DA. 2000, 3000 10/1968 and up, 2600, 3600, 4100, 2610, 3610, 4110 less cab, 83959550 - E6NN3K514CA. 4000 (10/1968-3/1970), 2600, 3600, 4110 with cab. Fits others replacing the following OEM numbers: D8NN3K514GA, D8NN3K514GB, D8NN3K514GC, E6NN3K514EA, 83917191, 83923736, 83924995, 83959533, 87759440, A709527 (Item #: 113209, Ref: E6NN3K514EA)$165.00
Power Steering Pump - E6NN3K514CA - For Ford tractor models 2000 (1/65-12/74), 2100 (3/65-12/74), 2110 (1/65-12/74), 2600 (1/75-12/81), 2600 (R (1/75-12/81), 2600 (N (1/75-12/81), 2600 (V (10/75-9/76), 3000 (1/65-12/74), 3100 (1/65-12/74), 3600 (R (1/75-12/77), 3600 (1/75-12/81), 3600 (N (1/75-12/81), 3600 (NO, V (1/75-12/81), 3900 (1/75-12/81), 4000 (1/65-12/74), 4100 (1/65-12/74), 4100 (1/75-12/81), 4110 (1/65-12/74), 4600 (1/75-12/81), 4600 (O (1/75-12/81), 4600 (NO (10/75-12/81), 4600SU (1/75-7/78), 5000 (1/65-1/75), 5100 (1/65-12/74), 5200 (1/67-12/74), 5600, 5700, 6600, 6600 (O), 6600, 6700, 7000, 7100, 7200, 7600, 7600, 7700, For Ford Construction and industrial models 231, 233, 333, 335, 420, 515, 531, 532, Replaces Ford OEM number E6NN3K514CA, 83959550, 850 PSI at 1000 RPM, 2.74 GPM, To validate your warranty: A contaminated system should be completely flushed by an authorized dealer. Use new, clean fluid and filters, (Item #: 157811)$307.00
Power Steering Pump Repair Kit - Kit repairs the following pumps: E6NN3K514EA, D8NN3K514KC, E0NN3K514AB, and E6NN3K514AB. For tractor models (2000, 3000, 4000, 5000 1965-9/1968), (8000, 8600, 9000, 9600 1/1968-2/1973), (Industrials 3400, 3500, 4400, 4500 1965-4/1970). NOTE: This kit is for pumps that used 2 - single lip seals. If your pump uses one double lip seal, use kit 83910651. (Item #: 113930, Ref: DHPN3A674B)$11.00
Power Steering Pump Repair Kit - This Seal and O-Ring Kit is for Power Steering Pumps with External Reservoirs. Fits; (2000, 3000, 4000 and 5000 1/1965-9/1968), (7000, 8000, 8600, 9000, 9600 1/1968-2/1973), Industrial; (3400, 3500, 4400, 4500 1/1965-4/1970), (2110LCG, 4110LCG 1965-9/1968). Contains: (2) D2NN3R542A O-Ring, (2) D2NN3R543A O-Ring, (2) E0NN3N529AA Seal, (1) E1ADKN994567 Seal, (2) 9861410 O-Ring, (1) 134373 O-Ring, (1) 9991976 O-Ring, (1) 379275S94 O-Ring, (1) 9617873 O-Ring. Replaces OEM part number DHPN3A674A. (Item #: 168490, Ref: DHPN3A674A)$61.00
Power Steering Pump Repair Kit - Kit repairs the following pumps: E6NN3K514EA, D8NN3K514KC, E0NN3K514AB, and E6NN3K514AB. Note, this kit contains 1 -Double Lip Seal. If your pump uses 2 - Single Lip Seals, use part number DHPN3A674B (Item #: 187034, Ref: 83910651)$13.30
Power Steering Seal Kit - Orbital Control Valve and Gear Box Gasket and Seal Kit. For tractor models (4000, 5000 from 7/1970 and up), 4600, 5600. 5610, 6600, 6610, 7000, 7600, 7610. NOTE If you are working on a 5600, 6600, 7600, 5610, 6610 or 7610 you will also need three E0NN3A590AA Teflon seals, sold seperately. Replaces EGPN3N503AA, C9NN3R668A, E1NN3N632AA, C9NN3N598A, C9NN3R669A, C9NN3C615A, 81803034. (Item #: 164631, Ref: EDPN3500A)$15.50
Power Steering Seal Kit - This Power Steering Seal Kit is used on steering gear assemblies. It contains (1) C9NN3747A, (1) C9NN3E614A, (2) C9NN3A590A, (2) C9NN3D624B, (1) E1NN3N632AA. Replaces EGPN3N503AA, 83957121 (Item #: 168433, Ref: EGPN3N503AA)$9.20
Power Steering Valve Seal - Teflon Seals for Steering Valve. This Seal is used with EDPN3500A Power Steering Seal Kit when used on 5600, 6600, 7600, 5610, 6610, 7610. Order 3. Price is for one. (Item #: 185754, Ref: E0NN3A590AA)$9.00
Reservoir Cap, Power Steering Pump - Used on E6NN3K514EA, D8NN3K514GC, C9NN3A674D Power Steering Pumps. For tractor models 231, 233, 2600, (3500, 3550 5/1970 to 1975), 3600, (4100 4/1970 to 1975), (420, 4600, 5600, 6600, 7600 1975 to 1981), 4600SU, (5100, 7100 7/1970 to 1975) and others. (Item #: 121241, Ref: D2NN3A006B)$3.70
Sector Shaft Oil Seal - Oil Seal, inner for Pitman Arm Sector Shaft. Used on 5000, 7000 (1965-1975), 5600, 6600, 7600 (1975-1981), 5610, 6610 (1981 and UP), POWER STEERING 5000, 7000 (1965-7/1970). Measures 2.000 Inches Outside Diameter, 1.500 Inches Inside Diameter and 0.250 Inches Wide. Wide. Replaces 81803190, C5NN3C615B (Item #: 161888, Ref: C5NN3C615B)$8.50
Shaft - Pivot Shaft for Center Power Steering Arm, 4.28 inches long. For tractor models: 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. (Item #: 152060, Ref: C5NN3N703C)$28.00
Spindle Bushing, Bearing and Seal Kit - This Spindle Bushing, Bearing and Seal Kit contains: 2 - C5NN3109A (1 5/8 inch X 2 inch X 1 7/8 inch) Bushings, 2 - C5NN3110A (1 3/4 inch X 2 inch X 1 7/8 inch) Bushings, 2 C0NN3A299A (2 inch ID X 2 7/8 inch OD) Thrust Bearings, 2 - C0NN3A208A (1 1/2 inch X 2 inch X 1/4 inch) Dust Seals. Used on Ford New Holland 5000, 5100, 5110, 5200, 5600, 6410, 6600, 6610, 6810, 7000, 7100, 7200, 7600, 7610 (Item #: 104568, Ref: SBBSKIT05)$37.00
Spindle Bushing, Lower - This Lower Spindle Bushing is measures 2.004 inch outside diameter, 1.760 inch inside diameter, wall thickness .119 inch, 1.860 inch long. It is used on Ford / New Holland 3010S, 4010S, 5000, 5100, 5110, 5340, 5600, 5610, 5610S, 5900, 6410, 6600, 6610, 6610S, 6810, 6810S, 7000, 7100, 7600, 7610, 7610S, 7700, 7810, 7810S, 8000, 8400, 8600, 9000, 9200, 9600. Replaces 81802797, C5NN3110A (Item #: 100641, Ref: C5NN3110A)$4.80
Spindle Bushing, Upper - This Upper Spindle Bushing measures 2 inch outside diameter, 1.645 inch inside diameter, 1.856 inch long, and wall thickness .176 inches. It is used on Ford / New Holland 3010S, 4010S, 5000, 5100, 5110, 5340, 5600, 5610, 5610S, 5900, 6410, 6600, 6610, 6610S, 6810, 6810S, 7000, 7100, 7600, 7610, 7610S, 7700, 7810, 7810S, 8000, 8400, 8600, 9000, 9200, 9600. Replaces 81802792, C5NN3109A (Item #: 100640, Ref: C5NN3109A)$5.40
Spindle, Heat Treated - Left Hand - For Ford tractor models 5100, 5600, 5610, 5900, 6410, 6600, 6610, 6810, 7100, 7600, 7610, Replaces Ford OEM number D6NN3106A, Dimension A: 16.000", Dimension B: 1.498", Dimension C: 1.638", Dimension D: 1.784", Dimension E: 1.625", Dimension F: .842", Left Side, Front wheel bearing kit use Item #: 100663, (Item #: 104547)$163.98
Spindle, Heat Treated - Right Hand - For Ford tractor models 5100, 5600, 5610, 5900, 6410, 6600, 6610, 6810, 7600, 7610, Replaces Ford OEM number D6NN3105A, Dimension A: 16.000", Dimension B: 1.498", Dimension C: 1.638", Dimension D: 1.748", Dimension E: 1.625", Dimension F: .842", Right Side, (Item #: 104549)$264.00
Spindle, High Clearance - LH - For Ford tractor models 5100 (1/1968-later), 5200, 5340 (1/1968-later), 5600 (1/1975-10/31/75), 6600 (1/1975-10/31/75), 7000 (10/1971-12/74), 7100 (1/1968-later), 7200, 7600 (1/1975-10/31/75), Replaces Ford OEM number C5NN3106K, Length: 16", Diameter: 1.75", Stem Diameter: 1.625", Stem Diameter: .843", Fits Left Hand Side, (Item #: 161169)$505.00
Spindle, High Clearance - RH - For Ford tractor models 5100 (1/1968-later), 5200, 5340 (1/1968-later), 5600 (1/1975-10/31/75), 6600 (1/1975-10/31/75), 7000 (10/1971-12/74), 7100 (1/1968-later), 7200, 7600 (1/1975-10/31/75), Replaces Ford OEM number C5NN3105N, Length: 16", Diameter: 1.75", Stem Diameter; 1.625", Stem Diameter: 0.843", Fits Right hand side, (Item #: 160192)$563.00
Spindle Left Hand - If you are using 10.00 x 16 inch tires on your Ford Tractor, this may be the left hand spindle you need. The measurements are A - 10.687 inches, B - 1.498 inches, C - 1.748 inches, D - 1.797 inches, E - 1.125\ inches. This spindle uses C0NN3A299A Thrust Bearing, C5NN3109A Upper Bushing, C5NN3110A Lower Bushing, -WBKFD7 Wheel Bearing Kit and 313020 Front Wheel Hub, 6 Bolt. Used on some of the following models: 3600, 4100, 4600, 5000, 5100, 5600, 6600, 7000, 7100, 7600. (Item #: 100639, Ref: D2NN3106C)$321.00
Spindle, LH - This spindle is used on tractor models 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. Uses Bushing Kit SBK6581. Uses front wheel hub part number C9NN1104D. Also uses wheel bearing kit part number WBKFD6. (Item #: 100643, Ref: C5NN3106J)$85.00
Spindle Nut - Fits on Front Spindles. Castle Nut 3/4 inch x 16 UNF. Replaces P2060, VLG3307, 351129S, 353928X1, 354573S36, 387930S36, 646060M1, 83416613, 83900513, 83910701, 880284M1, 9073, 98A750N. (Item #: 156038, Ref: 387930S36)$1.10
Spindle Nut - Fits on front spindles. Castle Nut 3/4 inch x 16 UNF. Replaces P2060, VLG3307, 351129S, 353928X1, 354573S36, 387930S36, 646060M1, 83416613, 83900513, 83910701, 880284M1, 9073, 98A750N. (Item #: 156038, Ref: 387930S36)$1.10
Spindle, RH - This spindle is for tractor models 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. Uses Bushing Kit SBK6581. Uses front wheel hub part number C9NN1104D. Also uses wheel bearing kit part number WBKFD6. (Item #: 100642, Ref: C5NN3105M)$84.00
Spindle, Right Hand - If you are using 10.00 x 16 inch tires on your Ford Tractor, this may be the right hand spindle you need. The measurements are A - 10.687 inches, B - 1.498 inches, C - 1.748 inches, D - 1.797 inches, E - 1.125\ inches. This spindle uses C0NN3A299A Thrust Bearing, C5NN3109A Upper Bushing, C5NN3110A Lower Bushing, -WBKFD7 Wheel Bearing Kit and 313020 Front Wheel Hub, 6 Bolt. Used on some of the following models: 3600, 4100, 4600, 5000, 5100, 5600, 6600, 7000, 7100, 7600. (Item #: 100638, Ref: D2NN3105C)$282.00
Spindle Seal MFWD - On Mechanical Front Wheel Drive tractors, the seal (o-ring) goes between the axle housing and the spindle. It is used on many ZF Axles. Replaces OEM part numbers 81296C1, 83946009, 8603728, 3147244R1, ZP0634303409, 1390411028, 81296C1, 1964258C1, 3147244R1 (Item #: 124682, Ref: 83946009)$0.50
Spindle Thrust Bearing - This Spindle Thrust Bearing measures: 2 3/64 inch (51mm) inside diameter, 2 15/16 inch (75mm) outside diameter, 5/8 inch (16mm) wide. Replaces 81802870, C0NN3A299A, 138712, 00138712, VPJ2403 (Item #: 100629, Ref: C0NN3A299A)$7.40
Steering Arm Dust Seal - This Steering Arm Dust Seal fits between the Steering Arm and the Spindle. It measures 1 7/8 Inches (48mm) Outside Diameter, 1 1/2 Inches (38mm) Inside Diameter, 1/4 Inches (6mm) Thick. Replaces 81802845, C0NN3A208A (Item #: 104573, Ref: C0NN3A208A)$4.10
Steering Arm - Left Hand - For Ford tractor models 5000, 5100, 5340, 5600, 5610, 5900, 6600, 6610, 7000, 7100, 7600, 7610, Replaces Ford OEM number C5NN3131A, All Models With Power Steering, Left Side, Tie Rod attaches from bottom of steering arm, (Item #: 100665)$66.00
Steering Arm - Left Hand - For Ford tractor models 5100, 5110, 5600, 5610, 5900, 6410, 6600, 6610, 6810, 7100, 7600, Replaces Ford OEM number E3NN3131AA, LH Steering Arm, (Item #: 104739)$126.00
Steering Arm, Left Hand - This Left Hand Steering Arm is used on Ford / New Holland Tractors: 5000, 5100, 5340, 5600, 5610, 6600, 6610, 7000, 7100, 7200, 7600. Replaces C5NN3131B, C5NN3131J, 81813163 (Item #: 104737, Ref: C5NN3131B)$192.00
Steering Arm - Left Hand, Used - For Ford tractor models 5000, 5100, 5340, 5600, 5610, 5900, 6600, 6610, 7000, 7100, 7600, 7610, Replaces Ford OEM number C5NN3131A, All Models With Power Steering, Left Side, Tie Rod attaches from bottom of steering arm, For a new version of this item use Item #: 100665, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 410665)$35.01
Steering Arm - Right Hand - For Ford tractor models 5000, 5100, 5340, 5600, 5610, 5900, 6600, 6610, 7000, 7100, 7600, 7610, Replaces Ford OEM number C5NN3130A, With Power Steering, Right Side, Tie Rod attaches from bottom of steering arm, (Item #: 100666)$71.44
Steering Arm - Right Hand - For Ford tractor models 5100, 5110, 5600, 5610, 5900, 6410, 6600, 6610, 6810, 7100, 7600, 7610, Replaces Ford OEM number E3NN3130AA, RH Steering Arm, Tie rod attaches to top of steering arm, (Item #: 104738)$145.00
Steering Arm Right Hand - For 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7700. Right Hand Steering Arm used with D2NN3105C, C5NN3105M, C7NN3105D. (Item #: 104736, Ref: C5NN3130J)$61.00
Steering Arm - Right Hand, Used - For Ford tractor models 5000, 5100, 5340, 5600, 5610, 5900, 6600, 6610, 7000, 7100, 7600, 7610, Replaces Ford OEM number C5NN3130A, With Power Steering, Tie Rod attaches from bottom of steering arm, Right Hand, For a new version of this item use Item #: 100666, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 410666)$44.01
Steering center arm pivot shaft bushing - Bushing, 1 inch long, for power steering center arm pivot shaft. Tractors 5000, 7000, 2 used from 1965 to 1/1966. Upper bushing for center arm pivot shaft, 1 used on tractors 5000, 7000 (2/1966-1975); 5600, 6600, 7600 (1975-1981); 5610, 6610, 7610 (1981-3/1985). (Item #: 153962, Ref: C5NN3179A)$5.10
Steering Gear Assembly, Manual - Manual Steering Gear, does not include drop arm. (Fits some models with power assist steering). Fits: 5100, 5110, 5340, 5600, 5610, 5900, 6410, 6600, 6600C, 6600O, 6700, 7100, 7600, 7600C, 7600O. Replaces D2NN3503A, D7NN3503A, D5NN3503D, 83912775, C5NN3503F. Note: When making a right hand turn, the steering are moves counter clockwise. (Item #: 161569, Ref: D7NN3503A)$661.00
Steering Sector Shaft Seal - Two of these felt seals are used per tractor. It measures 1.470 inch outside diameter, 0.925 inch inside diameter and 0.360 inch thick. Replaces 81826045, 8N3586, D2NN2N171A, 86553476 (Item #: 124494, Ref: 8N3586)$2.20
Steering Shaft Bearing - Bearing is for the upper and lower ends of the steering shaft. Verify measurements of .49 inches wide, 2.04 inches outside diameter and 1.18 inches inside diameter. For tractor models Major, Power Major, Super major. Replaces 353075S. (Item #: 169746, Ref: E1ADKN3556)$11.90
Steering Shaft Bushing - Bushing assembly, upper consists of a rubber splined piece with a metal bushing. Fits many Ford Tractors 1965 and up, with manual and power steering. Replaces C5NN3517A, 81811803, 83903807, D5NN3517A (Item #: 114044, Ref: C5NN3517A)$6.20
Steering Shaft Seal - This Steering Shaft Seal is for 2-wheel drive models steering box with 2 arms. Goes in the base of the steering shaft. It measures 1.386 inch outside diameter, 0.866 inch inside diameter and 0.374 inch in width. Tractors: 2100, 2110, 2120, 2150, 3055, 3100, 3120, 3150, 3400, 4110, 4140, 4410 (1965-1975), 2600, 3600, 3900, 4100, 4600SU, 335, 532 (with or w/o cab, 1975-3/1976; w/o cab 4/1976-1981), 2310, 2610, 2910, 3610, 3910, 3910SU, 4110SU, 4610SU, 230A, 234, 334, 530A (w/o cab 1981-9/1984). Replaces D5NN3N632A, E1NN3N632AA and 83929295. (Item #: 164336, Ref: E1NN3N632AA)$9.90
Steering Shaft with Nut - This Steering Shaft for manual steering is 28.750 inches long. It has right hand spiral. Turning the steering wheel clockwise causes the worm nut to travel up the shaft. It replaces original part numbers C5NN3A710B, D2NN3A710A and 81842811. If you need steering wheel nut order D5NN3N602A also. (Item #: 114039, Ref: D2NN3A710A)$79.00
Steering Wheel - This 3 spoke (covered spoke) steering wheel measures 18 inches in diameter on an 11/16 (tapered) 36 splined hub. Not like original. For 4 cylinder models, 8N, NAA, 600, 700, 800, 801, 900, 2000, 4000, 2600, 2610, 3000, 3600, 3610, 4100, 4110, 4600, 4610, 5000, 5600, 6600, 6610, 7000. (Item #: 101425, Ref: D6NN3600B)$34.00
Taper Roller Bearing - Measuring; Width - 0.548 inches, Inside Diameter - 3.740 inches, Outside Diameter - 5.315 inches, this bearing is used in ZF Axles on tractors with mechanical four wheel drive. This bearing also has other applications. Replaces OEM numbers: ZP0750117062, 5136951, 83946047, 81312C1, 83927807, 47539809, 1-31-741-019, 05136951, 85136951, 85806002, 1966169C1, CAR118378, 83983456, AL38099, RE45944, 819310, 819349/819310, 819349 (Item #: 156177, Ref: ZP0750117062)$73.00
Tie Rod - For Ford tractor models 5100, 5110, 5600, 5610, 6410, 6600, 6610, 7600, 7710, Replaces Ford OEM number 81816513, C5NN3282F, Dimension A: 18:625", Dimension B: .937", (Item #: 104638)$16.30
Tie Rod Assembly - For Ford tractor models 5600, 5700, 6600, 6700 (APL1351 4WD Front Axle), Replaces Ford OEM number 81927851, 81927505, (Item #: 160203)$383.00
Tie Rod Clamp - For Ford tractor models 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610 (All 01/65 - later), Replaces Ford OEM number C5NN3287C, 81816724, (Item #: 104623)$9.70
Tie Rod End - End, Tie Rod, left hand outer, 17.500 inches to center of post and .940 inch diameter. For tractor models: 5000, 5600, 5610, 660, 6610, 7000, 7600. (Item #: 104621, Ref: C7NN3280F)$36.10
Tie Rod End - End, Tie Rod, right hand outer, female end 0.937 inch 16 right hand threads, 4.250 inches to center of post. For tractor models: 5000, 5600, 5610, 6600, 6610, 7000, 7600. (Item #: 104622, Ref: C7NN3289E)$31.00
Tie Rod End - For Ford tractor models 4400, 4410, 5000, 5100, 5200, 5600, 5610, 6000, 6600, 6610, 7000, 7100, 7200, 7600, 7610, 8000, 8200, 8400, 8600, 8700, 9000, 9200, 9600, 9700, Replaces Ford OEM number E3NN3307AA, C5NN3307F, 3.812" Long, 1" Diameter, 16 Right Hand Thread, (Item #: 100687)$18.20
Tie Rod Inner - End, right hand inner, 1.00 inch-16 thread. For tie rod with power steering, 3.75 inch to center of post. For 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610, 8000, 8200, 8600, 9000, 9200, 9600. (Item #: 100682, Ref: C7NN3289D)$14.50
Tie Rod Inner - End, left hand inner, for tie rod with power steering, 18.125 inches to center of post. For tractor models: 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. Replaces 81822048, D6NN3B161A. (Item #: 100681, Ref: C7NN3B161A)$22.00
Tie Rod Outer - End, right hand outer, 15.375 inch to center of post, .937 inch diameter. For Tie Rod with Power Steering. For 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. Replaces C5NN3280E, 1802851, 81802851, 81822049, 1822049, 81859488, C5NN3208B, C5NN3280C. (Item #: 100680, Ref: C7NN3280E)$22.60
Tie Rod Outer - End, left hand outer, 15.375 inches to center of post. Rod diameter is 0.937 inches. For Tie Rod with Power Steering. For 5000, 5600, 5610, 6600, 6610, 7000, 7600, 7610. Replaces C5NN3281B, C5NN3281B, 81822050, 1822050. (Item #: 100679, Ref: C7NN3281A)$25.00
Tie Rod - Right Hand - For Ford tractor models 5600 (Hi-Clearance), 5610 (L/ FWD), 5900 (L/ FWD), 6600 (Hi-Clearance), 7600 (Hi-Clearance), 7610 (L/ FWD), Replaces Ford OEM number D8NN3280GA, Length: 12.562", Diameter: 0.937", Fits Right Hand Side, (Item #: 161155)$34.98
Tie Rod Tube - This is a Right Hand Tie Rod Tube used on 5000, 7000, 5600, 6600, 7600, 5610, 6610, 7610 (1981-3/1985). 16 inches. Replaces 86547157, C7NN3B624B. (Item #: 153561, Ref: C7NN3B624B)$37.00
Universal Joint - The measurements on this Universal Joint are 27mm cup diameter and 82mm across. Side greaser included. This Universal Joint is used on Carraro 4WD front axles. Replaces OEM numbers CAR96867, CAR116859, 3230277R1, 3216550R91, 137700420834, 1967554C1, 84512487, NH80715, 9961774, 9962244, 87760752, K965331, CAR041121, CAR116859, 83934724, 81927841, ZP1927504, ZP1927841, 3230277R1, 84512487, 83957857, AL32885, 137700000000, 3475808M91, 3475808M1, 3427352M91, 1895699M1 (Item #: 156129, Ref: CAR96867)$43.00
Wheel Hub Pin - Also known as a King Pin, this Wheel Hub Trunnion Pin is used on ZF APL1351 Mechanical Four Wheel Drive front ends. This part replaces, L35606, ZP1927576, 3216588R1, 81927576. Some of the models listed used more than one 4 wheel drive front end. Verify part number or axle number before ordering. Used on Ford 5600, 5700, 6600, 6700 (Item #: 124686, Ref: L35606)$32.00
Wheels
No Picture
15" x 30" 8 Loop Rear Rim, Silver Mist - For Ford tractor models 2310, 2600, 2610, 2910, 3000, 3500, 3610, 3900, 3910, 4000, 4100, 4110, 4140, 4190, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4610, 5000, 5110, 5190, 5200, 5600, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8210, 8530, 8630, 8730, 8830, Compatible with Ford Construction and industrial models 230A, 234, 334, 335, 420, 515, 530, 532, 535, Replaces Ford OEM number C5NN1100AE, D2NN1150L, D9NN1036GA, D9NN1050GA, Width: 15", Diameter: 30", Type: 8 Loop, Bolt Circle of Loops: 24.25", From Centerline to inside of Loop: 2.062", From Centerline to outside of Loop: 3.625", Valve stem side: 1, Rim Thickness: .187", Rim Color: Silver Mist, (Item #: 110436)$440.00
Front Hub, Heavy Duty / Industrial - Used on Heavy Duty and Industrial Front Ends. 3000, 4000 (4cyl, heavy duty front axle), 5100, 5110 (heavy duty axle), 5200, 5190, 5600 (10x16 tire), 5610 (heavy duty axle), 5700 (10x16 tire), 6600 (10x16 tire), 6610 (heavy duty axle), 6700 (10x16 tire), 6710 (heavy duty axle), 7100, 7200, 7410 (heavy duty axle), 7600 (10x16 tire), 7610 (heavy duty axle), 7700 (10x16 tire), 7710 (heavy duty axle), 8000, 8010, 9000, TW10, TW20, TW30, Industrial: 250C, 260C, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445D, 450, 515, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 1801, 3400, 3500, 3550, 4400, 4500, 4410. It uses C5NN1107F studs, and WBKFD7 wheel bearing kit, not included. Replaces OEM part number 313020. Verify part number before ordering. (Item #: 100662, Ref: 313020)$68.00
Front Rim - This is a 5.5 inch x 18 inch Front Wheel Rim. Used with 7.50 x 18 Tires. It has a pilot hole of 4.656 inches. It uses 6 bolts in a 6 inch bolt pattern. Verify size of old rim before ordering. Replace 3121425R91, 804711R91, K301046, K949731, 3121425R91, 83960329, C7NN1007B, 83918556, 81825697, 81820016, D1NN1007C, D8NN1007CA, 82005057, 82033932, E6NN1007CA, D4NN1007N, JD3211, AL82491, 3827583M91, 186319M91, 1861319M91 (Item #: 167680, Ref: FW55186)$146.00
Front Rim - Heavy Duty - Front Rim with weight holes. 5.5 inch x 16 inch, 3300 lb. capacity. 6 bolt, 6 inch circle, 4.62 inch pilot. For 7.5 inch x 16 inch tires. Additional $25 shipping due to size and weight. Replaces 82005056, 83960327, 83926073, 83954658, 81816955, E6NN1007BA, C7NN1007J, C9NN1007C, 83936990, D2NN1007N, D2NN1007R29Z, D2NN1007S, 83900159, C5NN1007A (Item #: 116854, Ref: FW55166)$70.00
Hub Cap, Cast Iron - This is a threaded, Cast Iron Hub Cap, used on Ford / New Holland 3010S, 4010S, 5000, 5110, 5190, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7410, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8210, TS100, TS110, TS90. Replaces C5NN1130A, 81811270, 81802363 (Item #: 100664, Ref: C5NN1130A)$6.00
Hub Cap, Stamped Steel - This is a threaded, Stamped Steel Hub Cap, used on Ford / New Holland 3010S, 4010S, 5000, 5110, 5190, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7410, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8210, TS100, TS110, TS90. Replaces C5NN1130A, 81811270, 81802363 (Item #: 167593, Ref: C5NN1130ASS)$6.10
Rear Axle Stud - This Rear Axle Stud connects the rear axle to the wheel center disc. It is used with C5NN1120E nut. 3/4 inch x 2 5/16 inch 16 (UNF) Thread. Replaces C5NN1N118J, C5NN1N118H, 81815740, 81815607, 81815739 (Item #: 115382, Ref: C5NN1N118H)$4.20
Rear Spinout Rim Stop - For 90 degree drilled rim rail. For spin out rims with 4 sided rectangle shaped stops. Limited applications, verify style before ordering. Will NOT fit the spinout rims that we offer. Replaces 232274, 1755060M1, 230832, 70230832, 7023227, E5NN1057BA, K917337, T14751 (Item #: 152053, Ref: 1755060M1)$19.50
Rear Wheel Center - This disc is used on multiple Ford models. Check measurements before ordering. Disc, rear wheel 28 inch and 32 inch, 8-bolt hub, 6-bolt rim. Center hole: 4-5/16 inches, hub pattern: 8 lug - 6 inch bolt pattern. Replaces Ford OEM numbers D9NN1036CA, F1NN1036KA, 86512668, C5NN1036D, 957E1017B. Additional $35 shipping due to weight. (Item #: 149804, Ref: D9NN1036CA)$220.00
Rim Center - Rear Wheel, 28" and 32" with 8 holes, Used - For Ford tractor models NAA, 2N, 8N, 9N, 501, 540, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 761, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2031, 2100, 2110, 2111, 2120, 2130, 2131, 2310, 2600, 2610, 2910, 3000, 3055, 3100, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3600, 3610, 3900, 3910, 4000, 4030, 4031, 4100, 4110, 4120, 4121, 4130, 4131, 4140, 4600, 4610, 5600, 5700, 6600, 6700, 7600, 7700, Compatible with Ford Construction and industrial models 230A, 233, 234, 333, 334, 335, 420, 515, 530A, 531, 535, 541, 1800, 1801, 1811, 1821, 1841, 1881, 2030, 3500, 4040, 4140 Replaces Ford OEM number D9NN1036CA, F1NN1036KA, 86512668, C5NN1036D, 957E1017B, , Compatible with Massey Ferguson tractor models F40, TE20, TEA20, TO20, TO30, 35, 50, 130, 133, 135, 140, 148, 150, 154, 154-4, 155, 158, 165, 168, 174, 174-4, 175, 178, 180, 184, 184-4, 185, 188, 194, 194-4, 202, 204, 230, 235, 240, 245, 250, 550, 2135 Replaces Massey Ferguson OEM nos 193701M1, 772861M1, 1678566M1, 1882977M1, 963613M1, , Compatible with Massey Harris tractor models 50, For rear rims 28" or 32" both 6 loop, Center hole: 4-5/16", Hub pattern: 8 lug - 6" bolt pattern, For a new version of this item use Item #: 149804, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435978)$125.01
Rim Center - Rear Wheel, 28" and 32" with 8 holes, Used - For Ford tractor models NAA, 2N, 8N, 9N, 501, 540, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 761, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2031, 2100, 2110, 2111, 2120, 2130, 2131, 2310, 2600, 2610, 2910, 3000, 3055, 3100, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3600, 3610, 3900, 3910, 4000, 4030, 4031, 4100, 4110, 4120, 4121, 4130, 4131, 4140, 4600, 4610, 5600, 5700, 6600, 6700, 7600, 7700, Compatible with Ford Construction and industrial models 230A, 233, 234, 333, 334, 335, 420, 515, 530A, 531, 535, 541, 1800, 1801, 1811, 1821, 1841, 1881, 2030, 3500, 4040, 4140 Replaces Ford OEM number D9NN1036CA, F1NN1036KA, 86512668, C5NN1036D, 957E1017B, , Compatible with Massey Ferguson tractor models F40, TE20, TEA20, TO20, TO30, 35, 50, 130, 133, 135, 140, 148, 150, 154, 154-4, 155, 158, 165, 168, 174, 174-4, 175, 178, 180, 184, 184-4, 185, 188, 194, 194-4, 202, 204, 230, 235, 240, 245, 250, 550, 2135 Replaces Massey Ferguson OEM nos 193701M1, 772861M1, 1678566M1, 1882977M1, 963613M1, , Compatible with Massey Harris tractor models 50, For rear rims 28" or 32" both 6 loop, Center hole: 4-5/16", Hub pattern: 8 lug - 6" bolt pattern, For a new version of this item use Item #: 149804, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435978)$125.01
Rim Clamp, Used - For Ford tractor models 3230, 3430, 3930, 4000, 4030, 4100, 4110, 4130, 4190, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7840, 8000, 8200, 8210, 8240, 8340, 8400, 8600, 8700, 9000, 9200, 9600, 9700, Compatible with New Holland tractor models TS90, TS100, TS110, TS115, Replaces OEM nos 81821553, Replaces Casting nos C9NN1043F, For Power Adjust Wheels, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 497001)$37.01
Rim Stop Screw - For Ford tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35, 2000, 2100, 2110, 2120, 2150, 2300, 2310, 2600, 2610, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 3330, 3400, 3430, 3500, 3600, 3610, 3910, 3930, 4000, 4100, 4110, 4130, 4140, 4190, 4200, 4330, 4340, 4400, 4410, 4500, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6000, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7840, 8000, 8200, 8210, 8340, 8400, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9030, 9600, 9700, Compatible with Ford Construction and industrial models 256V, 276, Compatible with New Holland tractor models TS100, TS110, Replaces New Holland OEM number 81811263, C0NN1058A, Screw for stop body, Use with power adjust rims PAR10X28, C5NN1050J, and C5NN1050H, Rear rim stop screw, (Item #: 151948)$7.70
Spindle Tab Washer - This Tab Washer is used on some Ford Tractors 1939-and later. Measures 1.516 inch outside diameter, 0.78 inch inside diameter, 0.089 inch thick. It replaces original part numbers C5NN1N195A, 81811561, 9N1195. (Item #: 164443, Ref: C5NN1N195A)$3.40
Spindle Tab Washer - This Tab Washer is used on some Ford Tractors 1939-and later. Measures 1.50 inches (38.20mm) outside diameter, .775 inch (19.70mm) inside diameter, 0.0625 (1.23mm) inch thick. It replaces original part numbers 957E1195, 81802388, 83910701, 898349M2, 180010M1, 180010M2 (Item #: 173191, Ref: 957E1195)$1.50
Stop Body Screw, Single - This stop body screw for the rear wheel rim is used with power adjust rims PAR10X28, C5NN1050J and C5NN1050H. Replaces: 81811263, C0NN1058A. YOU MAY RECEIVE A HEX HEAD OR SQUARE HEAD. (Item #: 155118, Ref: C0NN1058A)$6.90
Wheel Hub Kit - For Ford tractor models 5000, 5100, 5110, 5600, 5610, 5640, 5700, 5900, 6410, 6640, 6700, 6710, 6810, 7000, 7100, 7600, 7610, 7700, Replaces Ford OEM number C9NN1104D, C5NN1130A, E2156T9, EHPN1200D, C5NN1107F, (Item #: 113372)$86.00
Wheel Nut - This Cone Wheel Nut is 3/4 - 16 Thread (UNF). It is used for the center disc to rear axle. It is used with C5NN1N118H Studs. Replaces 81816136, 81833776, C5NN1120E, D3NN1120B (Item #: 156987, Ref: C5NN1120E)$3.60
Wheel Rim, Rim Size: 10 x 28 - The Assembly Contains a 10 x 28 Rim, the center disc and hardware. Comes assembled. Suitable for Tire size: 12.4 x 28, Alternative Tire size: 11.2 x 28. The rim measures 10 Inches from bead to bead where the tire rests. Center hole: 4-5/16 inches, hub pattern: 8 lug - 6 inch bolt pattern. Verify all measurements before ordering. Replaces D9NN1036CA, D9NN1036CA, F1NN1036KA, 86512668, C5NN1036D, 957E1017B, C0NN1050F, NCA1020B, 33806S34, 33806S36, 33806S7, 350719S8, 370938S36, 370938S43, 408, 81821369. Additional $35 shipping due to weight. (Item #: 178951, Ref: S61968)$635.00
Universal Parts and Accessories Category: Accessories / Supplies
Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127)$365.01
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153)$100.55
Cooling System
Thermostat Housing to Block Gasket - Tractors: all 4-cylinder, 1953-1964, gas and diesel. Bolt holes measure 3/8 inch in diameter, and center to center of bolt hole spacing is 2 3/4 inches. Sold and Priced as Each. (Item #: 191970, Ref: EAF8255A)$5.20
Decals and Emblems
Decal, Fear This Ford - 12-1/2 inches x 3 inches. For all Ford tractors. (Item #: 183476, Ref: S.67825)$15.87
Sherman Transmission Instruction Plate - For Ford models with Sherman step up step down transmission. Installs under steering wheel nut. (Item #: 178113, Ref: SHERMAN)$20.90
Drive Train
Shift Cover Plate Gasket - For all models with 5-SPEED transmission built between 1955-1964. Not for tractors made overseas, such as Major, Dexta, etc. (Item #: 178105, Ref: NDA7223A)$10.00
Electrical System
NOTE
Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.
NOTE
No Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE)$84.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209)$13.10
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302)$25.20
No Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010)$55.00
No Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85)$5.50
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425)$4.50
NOTE
Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!
NOTE
Starter Solenoid, 12 Volt - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. (Item #: 150223, Ref: DR1467)$18.50
Switch, Push Button - This 2 terminal switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch overall length. Check measurements before ordering if using as a universal part. Applications include ether switch, horn button, cold start, starter switch, and manifold heater switch. It replaces 22702, 240962, 242988, 245866, 245936, 70253322, 71191589, 72160068, VT507, 86900358, A30858, O9995AB, T18524, TG07803, TO18117, TO7803, 271179R91, 367678R91, 373611R91, 393209R91, AR46184, AR47373, AR47374, R39554, 189158M91, 767828M91, 105386A, 10A972, 1K7392C, UT2421, 1K7392A, 7A7392. (Item #: 121141, Ref: R7994)$11.70
Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR)$10.60
Engine Parts
NOTE
Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).
NOTE
Engine Pistons and Sleeves
No Picture
Seal Kit - Seal kit, for cylinder E2NN3A540BA. Piston rod is retained with 1" snap ring and 1-3/4" threaded spanner nut. (Item #: E2NN3X-SK)$64.99
Engine Rings
NOTE
Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").
NOTE
Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C)$76.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C)$103.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C)$123.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR)$106.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR)$167.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C)$147.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C)$170.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR)$89.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114)$3.30
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134)$4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138)$2.80
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214)$4.58
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234)$8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300)$7.30
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312)$8.90
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400)$8.70
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500)$14.30
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799)$10.10
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800)$9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802)$11.10
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804)$11.40
Rain Cap - This rain cap is for a 4.00 inch pipe. (Item #: 108645, Ref: R1807)$11.00
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14)$14.30
Rain Cap - This rain cap is for a 5.00 inch pipe. (Item #: 108750, Ref: WC15)$18.38
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A)$6.80
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A)$7.50
Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231)$12.60
Filter Screen and Gasket for Sediment Bowl - 1-1/2 inch outside diameter seal (for a 1 9/16 inside diameter housing and a 1 3/8 inch outside diameter screen. Measure before ordering. For tractor models (1958-1964 All with 134 cubic inch engines), 2000 4 cylinder, 501, 601, 701, (1958-1960 all with 172 cubic inch engines up to 126524), 801, 901, 1801. (Item #: 150700, Ref: ABC346)$5.60
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949)$9.92
Gauges
Ammeter, Black, Flat Bezel - For all models to 1958. Terminal type ammeter. 30-0-30. Black ring. Replaces FAD10850A. (Item #: 110410, Ref: A0NN10670A-BLAC)$7.00
No Picture
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771)$58.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672)$41.00
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095)$14.90
Hitch / Drawbar
Drawbar - Number Of Drawbar Holes: 11 Hole``Made of 1" x 2-1/2" high carbon steel``Category: 1``Length: 26"``End Pins: 7/8"``Hitch Pin Holes - 3/4" (Item #: 103174, Ref: 9N5182)$44.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X)$11.50
Link End - Plated, forged, 1-1/4 inch thread, left hand, 1 inch hole. (Item #: 180473, Ref: RE1717L)$20.50
Link End - Plated, forged, 1-1/4 inch thread, right hand, 1 inch hole. (Item #: 174507, Ref: RE1718R)$24.50
Stabilizer Arm HD - Arm only, made of alloy spring steel, for kit 231253XHD, red only. 7/8 inch hole diameter. 31 1/2 inches center to center. (Item #: 110516, Ref: 230042XHD)$15.20
Top Link - Forged Top Link, 12 inch body, Category I implement ends. Adjusts 17.5 to 24 inches overall. 3/4 inch pin holes and both eyelets are 1 3/4 inch wide. Dichromate plated. (Item #: 103162, Ref: JSA1012C)$24.00
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2)$37.00
Hydraulic System
Coupler Flange - FORD: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b (Item #: 108772, Ref: L36-6)$119.41
Coupler Flange - Drive flange; 3/4 inch round bore with set screw 1/4 inch x 3/8 inch. 1-15/16 inch spacing. For Morflex series 302. Replaces: L363, 191061, 1752219M91, L36-3 (Item #: 112104, Ref: 191061)$22.00
Coupler for Pump Shaft - The Hydraulic Pump Shaft Coupler is 1-1/2 Outside Diameter and 2-1/4 inches long. It 7/8 inch 13 splined inside. It replaces 1631413, 350-1631413, S340 (Item #: 114586, Ref: S340)$37.00
Cylinder Seal Kit, For 2 inch cylinders - For TISCO side and top link replacement cylinders. Seal Repair Kit for 2 inch cylinders. For cylinder numbers: HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. (Item #: 183971, Ref: HSK2002)$22.50
Cylinder Seal Kit, For 3 inch Cylinders - For TISCO brand side and top link replacement cylinders ONLY. Seal Repair Kit for 3" cylinders. For cylinder numbers: HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. (Item #: 179480, Ref: HSK3002)$29.50
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023)$25.70
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021)$15.20
Hub - 7/8 inch, 13 spline threaded, 3-7/8 inch hole spacing. For 730 LOADER. Used with C5NNN879A hub. (Item #: 160204, Ref: 291315)$65.00
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12)$11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180)$55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24)$13.50
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30)$16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48)$16.50
Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199)$21.10
Hydraulic Pump for Loader - Part Description: Pump, Hydraulic For 730 LOADER, 735 LOADER. SPECS: CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, PORT SIZE INLET: 1-5/8 inches-12 ORB, PORT SIZE OUTLET: 1-5/16 inches-12 ORB, MOUNTING: 2 bolt SAE "B", FORD PUMP APPLICATION: 730 and 735 loaders, CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, MOUNTING: 2 bolt SAE "B", INLET: 1-5/8 inches-12 ORB, OUTLET: 1-5/16 inches-12 ORB. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inches and Maximum is 6 7/8 inches. (Item #: 127269, Ref: 7702425-29Z)$770.00
Hydraulic Pump, Front Mounted - This Hydraulic Pump is used with some 701, 702 and 703 Loaders. It is 14 Gallons Per Minute at 2000 RPM. The shaft is 3/4 inch round with a key way. Left Hand Rotation. Inlet is 1 Inch NPT. Outlet is 3/4 Inch NPT. Mounting bolt spacing 4 3/16 inches center to center. Comes with two adapters. Contains: 1-720FSO-3/4X3/4 HC4008 adapter, 1-720FSO-1X1-1/4 HC4009 adapter. This Pump may work in other loader application. Verify Specs before ordering. (Item #: 182700, Ref: L827-10X-LB)$585.00
Hydraulic Valve Kit - Valve with handles, three-spool, 2000 p.s.i. Relief, all spools tandem (4-way) spring center to neutral. (Item #: HV4030)$787.98
LBP Coupler Center - Center member. Center member. 3-5/8" O.D., four 5/16" holes, 2-1/4" bolt circle (L52-10) For tractor models 352. (Item #: 178931, Ref: 192169)$70.00
LBP Hydraulic hose Assembly - Hydraulic hose assembly. For Ford model 740 LOADER. (Item #: 179521, Ref: 7701142)$29.20
Morflex Center Member - This is a 1-302 Morflex Center member. It measures 3-1/8 inch diameter, four 1/4 inch holes, 1-15/16 inch bolt circle. Replaces part numbers 893129, 191192, L5227, 1506097M91, 1086870M1, 191192LBP, 1752218M91, L52-27 (Item #: 116952, Ref: 191192LBP)$55.00
Top Link, Hydraulic - FORD: Hydraulic top link cylinder. All ports 9/16 inch-18 O-ring boss with two adapters 9/16 inch-18 ORBM x 1/4 inch NPTM 90 degree swivel. 3 inch cylinder bore, 8 inch stroke length, 26 inch closed length, 12-7/16 inch barrel length, 1 inch rod end diameter, 1-3/4 inch rod end width, 1 inch diameter base end. (Item #: 167145, Ref: HTL3103)$276.00
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000)$16.10
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60)$16.10
Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317)$15.50
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269)$183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215)$123.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH)$39.00
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311)$51.00
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH)$53.00
No Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP)$21.50
No Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP)$21.50
Lights
Headlight Assembly, 12 Volt - (Single) Headlight Assembly 12-volt, blue - Sealed beam headlamp assembly in heavy gauge steel housing with Rubber bezel. Does not look like original. (Item #: 184496, Ref: L525HB-12V)$56.00
Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R)$16.60
No Picture
Sealed Beam Bulb, 12 Volt - Red/white combination work/tail light, 4-1/2 inch diameter. (Item #: 116014, Ref: S.52670)$24.50
Tail Light Lens - Plastic 4 inch lens for DUOLAMP with FOMOCO stamped on lens (has 2 mounting screw holes spaced 3 1/8 inches apart). Fits tractors 1953 and newer. (Item #: 178144, Ref: FDV13450A)$16.50
Miscellaneous
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B)$245.00
Tractor Umbrella with Frame & Mounting Bracket - Blue - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without Additional Handling & Oversize Fees Apply To This Item, tools, (Item #: 161190)$118.00
Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250)$24.00
No Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP)$8.50
No Picture
Paint, Brownish Medium Gray, 1 Quart - Ford Brownish Medium Gray was used for the same applications as TP240Ford Medium Gray. This is a lighter shade. Since the tractors did not come off the production line all the same, the darker or light shades are completely up to the desires of the customer. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184575, Ref: TP245QT)$50.00
No Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL)$69.00
No Picture
Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT)$29.50
No Picture
Paint, Empire Blue, 1 Gallon - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100713, Ref: TP360GAL)$56.00
No Picture
Paint, Empire Blue, 1 Quart - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100712, Ref: TP360QT)$23.50
No Picture
Paint, Empire Blue, Spray Can - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100711, Ref: TP360SP)$7.30
No Picture
Paint, Ford White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108135, Ref: TP470GAL)$82.00
No Picture
Paint, Ford White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108133, Ref: TP470SP)$11.60
No Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL)$56.00
No Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT)$23.60
No Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP)$8.50
No Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT)$22.50
No Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100120, Ref: TP2700SP)$8.30
No Picture
Paint, Industrial Yellow, Spray - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100723, Ref: TP760SP)$7.90
No Picture
Paint, Light Gray, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100716, Ref: TP330GAL)$57.00
No Picture
Paint, Light Gray, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100715, Ref: TP330QT)$23.50
No Picture
Paint, Light Gray, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100714, Ref: TP330SP)$8.50
No Picture
Paint, Medium Gray, 1 Quart - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100718, Ref: TP240QT)$22.10
No Picture
Paint, Medium Gray, Spray Can - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100717, Ref: TP240SP)$8.80
No Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL)$62.00
No Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT)$23.50
No Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT)$17.00
No Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP)$7.90
No Picture
Paint, Vibrant Blue, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156586, Ref: TP365GAL)$92.00
No Picture
Paint, Vibrant Blue, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156587, Ref: TP365QT)$38.00
No Picture
Paint, Vibrant Blue, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156585, Ref: TP365SP)$10.50
No Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL)$84.67
No Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL)$68.39
No Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT)$99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R)$45.00
PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY)$176.91
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33)$339.00
NOTE
PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.
NOTE
PTO Overide Clutch - This 6 spline Override Coupler converts a 1 1/8 inch diameter PTO shaft to 1 3/8. It has a 1 1/8 inch female at one end and 1 3/8 inch male at the other end). Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103169, Ref: C670F)$51.00
PTO Overide Clutch - Override coupler for 1 3/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 191020, Ref: C680F)$73.00
PTO Overide Clutch - Override coupler for 1 1/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103167, Ref: C690F)$76.00
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164)$258.00
Seats
Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V)$1518.86
Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056)$2161.57
Seat Cushion, Black - Cover with piping and Ford script logo. Fits all 1939-1964 models with a 17 inch wide steel seat pan. (Item #: 115058, Ref: 8N401BLK)$59.00
Tie-On Seat Cover - Blue and White, 19 inches wide. Deluxe with 2 inches of foam. (Item #: 101353, Ref: R1013)$36.00
Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP)$100.00
Sheet Metal / Body Parts
Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140)$41.19
Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K)$178.00
Steering
Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417)$49.00
Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16 inches x 5/8 inch x 5/8 inch, 1 15/16 inches x 3/4 inch, 3/4 inch, and 1 3/8 inches x 1 inch x 1/2 inch. (Item #: 183427, Ref: TIERODBOOTS)$14.30
Tools
No Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891)$24.30
Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. (Item #: 103768, Ref: FW60166)$100.00
Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166)$70.00
Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB)$17.15
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R)$45.00
Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050)$17.50
No Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058)$63.00
No Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062)$67.00
Wheel Clamp - Wheel clamp holding disc to rim for double ramp type on power adjustable rims. For 28 inch rim on tractors 2000, 3000, 4140, (10-1968 to 1975); 2600, 3600, 4100, 4600SU except Baseldon models, (1981 to 3-1990); 3230, 3430, 3930, 4130, 4630, 4830LCG, (3-1990 to -) Use with rims PAR10X18 and C5NN1050J and C5NN1050H. Also replaces 3615259M1, 70235676 and 7000000241, E5NN1043AA. (Item #: 124526, Ref: 898021M1)$18.10
Wheel Front 8X16 - Front Wheel 8 inch x 16 inch ; 6 bolt, 6 inch circle, 4.62 inch pilot. (Item #: 180445, Ref: D5NN1007A)$112.00
If you will be servicing or maintaining your tractor, we highly recommend that you have a manual to refer to. We searched the tractor manual database and found the following items. They may or may not apply to your tractor, please read the descriptions carefully. Our search engine isn't perfect... yet!
YESTERDAY's TRACTORS
has been a leading tractor parts supplier on
the internet since 1995. Join thousands of happy customers
who have purchased parts and more for their antique tractor from us!
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
