FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Ford 8010 Tractor Parts

[Categories] [All Ford Models] [Print]

Brakes

Brake Actuator Rod - For tractor models (5610, 5900, 6610, 6710, 6810, 7610, 8010 all 5/1989 and up), 5610S, 6610S, 7610S, 7810S, 5640, 6640, 7740, 7840, 8240, 8340, TS90, TS100, TS110. (Item #: 182778, Ref: E8NN2466DA) $23.20

Brake Cross Shaft Bushing - Outside diameter 1 1/4 inches, inside diameter 1 1/8 inches, length 1 inch. Fits 2000, 3000, 4000, 5000, 7000, 2600, 3600, 3900, 4100, 4600, 5600, 5900, 6600, 6700, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4110, 4610, 5610, 6610, 6710, 7610, 7710, 7810, 7910, 8010, 8210, 3230, 3930, 4130, 4630, 4830, 5030, 5640, 6640, 7740, 7840, 8240, TS90, TS100, TS110. INDUSTRIALS: 230A, 231, 234, 250C, 260C, 2110LCG, 334, 335, 340A, 345C, 3400, 3500, 3550, 420, 445, 450, 4400, 4500, 530A, 531, 532, 535, 540, 545, 550, 555, 5500, 650, 655, 6500, 750, 755, 7500. (Item #: 151822, Ref: C5NN2N477A) $5.70

Brake Disc, 9 Inch - With 1-9/32 inch wide lining, this disc was used in later production than the 5/8 width lining. This disc is 8 7/8 inches outside diameter, 2 1/8 inches inside diameter, facing width 1.31 inches, 22 internal tooth count. Used with 9 inch actuators. This part replaces Ford part numbers E9NN2A097BA, E9NN2N097BA, 83989830, 81818854, 83956599, E6NN2A097AA, 87518036, C7NN2A097B. (Item #: 105499, Ref: E9NN2A097BA) $26.10

Brake Disc, Intermediate Steel - Used with 9 inch actuators, this intermediate steel disc measures 8.976 outside diameter and 5 inch inside diameter. This part replaces Ford OEM numbers E6NN2N315AA, E6NN2N615AA, 83956598. Used on the following with 9 inch actuator disc brakes: 3600, 4600, 5000, 5100, 5110, 5200, 532, 5340, 5500, 5550, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 650, 6500, 660, 6600, 661, 6610, 6610S, 6640, 6700, 6710, 681, 6810, 7000, 7010, 7100, 7200, 7410, 755, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8030, 8210, 8240, 8340, TS100, TS110, TS120A, TS6000 Brazilian, TS6020 Brazilian, TS6030 Brazilian, TS6040 Brazilian, TS80, TS90 (Item #: 105513, Ref: E6NN2N315AA) $14.50

Brake Rod Seal - For tractor models 3000, 4000, 5000, 7000, 3900, 4100, 4600, 5600, 5900, 6600, 6700, 7600, 7700, 2810, 2910, 3910, 4110, 4610, 5610, 5610S, 6610, 6610S, 6710, 6810, 7610, 7610S, 7710, 7810, 7810S, 7910, 8010, 8210, 3230, 3430, 3930, 4130, 4630, 4830, 5030, (5640, 6640, 7740, 7840, 8240, 8340 with 8 x 2 or 16 x 4 transmission), 250C, 260C, 335, 340, 340A, 340B. Replaces E7NN2N336A, 85999093. (Item #: 105644, Ref: C5NN2N336A) $3.50

Brake Shaft Felt Seal - This Brake Shaft Felt Seal measures 1.470 inch outside diameter, 0.925 inch inside diameter and 0.360 inch thick. Replaces 81826045, 8N3586, D2NN2N171A, 86553476, C5NN3586A (Item #: 124494, Ref: 8N3586) $2.10

Brake Shaft Seal - This Brake Shaft Seal measures 1.565 inch outside diameter, 1-1/16 inch inside diameter. It replaces original part numbers C5NN2473F, C5NN2473H, C5NN2N258C, D2NN2N258A, D8NN2N289AA, D9NN2N289AA, 65968, 83924047. (Item #: 150914, Ref: D9NN2N289AA) $3.30

Clutch

Clutch Bearing - Pilot - Pilot Ball Bearing, for PTO Drive Plate. Inside diameter 1.4370 inch, outside diameter 2.6772 inch, width 0.5906 inch. Replaces 83992560, F0NNN779AA (Item #: 108005, Ref: F0NNN779AA) $15.20

Clutch Disc - 13 inch, 10 spline, 1-3/4 inch hub, rigid woven disc. Tractors: 5000 (1/1965-9/1969) Dual power, 5110 (1/981-12/1992) Dual power, 5200, 5340 (1/1965-9/1969) Dual power, 5640 (11/1991-), 5700 (1/1975-) Dual power, 6410 (1/1981-12/1992), 6600, 6700 (10/1975-10/1981) Dual power, 6610 (1/1981-) Dual power, 6640 (11/1991-), 6710 (1/1981-) Dual power, 7000 (10/1971-9/1975) Dual power, 7100, 7200 (10/1971-9/1975) Dual power, 7600, 7700 (10/1971-9/1975) Dual power, 8010, 8210 (4/1996-), TS90, TS100, TS110 (11/1997-). (Item #: 178334, Ref: 82011594) $145.00

Clutch Disc - 13 inch, 10 spline, 1-3/4 inch hub, 6 pad, dampened disc. Tractors: 5610 (1/81-), 5640 (11/91-), 6610 (1/81-) Dual power, 6640 (11/91), 7100, 7200 (10/71-9/75) Dual power, 7600, 7700 (10/71-9/75) Dual power, 7610, 7710 (1/81-) Dual power, 7740, 7840 (11/91-), 7810, 7910 (10/85-3/88), 8010, 8210 (4/96-), 8340 (11/91-), TS90, TS100, TS110 (11/97-). (Item #: 158737, Ref: E8NN7550PA) $264.00

Clutch Kit - This new single stage clutch kit contains a new 13 inch pressure plate assembly with a 2.5 inch hub (D8NN7563AB), a new 13 inch, 25 spline, 1.625 inch hub, rigid drive disc (D2NN7550A), new release bearing (83914247), new pilot bearing (F0NNN779AA), and a clutch alignment tool. Fits Tractors 4600, 4600NO, 4600SU, 5000, 5100, 5190, 5200, 5340, 5600, 5610, 5610S, 5700, 6410, 6600, 6600C, 6610, 6610S, 6700, 6810S, 7000, 7010, 7100, 7200, 7600, 7600C, 7610, 7610O, 7610S, 7700, 7710, 7810, 7810S, 7910, 8010, 8210, 9610. (Item #: 112323, Ref: FD13P25RD) $282.00

Clutch Kit, 13 Inch Single - This Kit contains 13 inch - 10 spline spring drive disc with 1 3/4 inch hub 82011593, 13 inch single pressure plate w/ring D8NN7563AB, pilot bearing F0NNN779AA and release bearing 83914247, includes pilot tool. Replaces 82006046, 82011593, D8NN7563AB (Item #: 112322, Ref: 11126087) $350.00

Clutch Kit - Single - This new complete clutch kit (for flat flywheel step) contains: a 13 inch single pressure plate, with ring (D8NN7563AB), 13 inch 10 spline rigid 1.75 inch hub disc (82011593), a pilot bearing that measures 1.437 inch inside diameter, 2.6772 inch outside diameter, .59 inch wide (F0NNN779AA), a release bearing that measures 2.5 inch inside diameter, 4.125 inch outside diameter, .870 inch wide (83914247), and clutch alignment tool. For tractor models: 4600, 4600SU, 5000, 5110, 5190, 5340, 5600, 5610, 5610S, 5700, 6410, 6600, 6610, 6610S, 6700, 6710, 6810, 6810S, 7000, 7010, 7600, 7610, 7610S, 7700, 7710, 7810, 7810S, 7910, 8010, 8210. (Item #: 112322, Ref: D8NN7563AB-KIT) $350.00

Clutch Pedal Return Spring - This Clutch Pedal Return Spring is used on multiple Ford/ New Holland Tractors and Industrial Models, build 1965 and later. It replaces original part numbers C7NN7N598A and 81820895 (Item #: 153432, Ref: C7NN7N598A) $4.60

Release Bearing - This Clutch Release Bearing. Inside diameter 2.4997 inches, outside diameter 4.0700 inches, width 0.8700 inches. This is used in multiple Ford Tractors. Replaces original part numbers D8NN7580AA, D8NN7580BA, D8NN7580BB, E4NN7580AA, 82010859, 83914247, 83933520, 83946908, 86534551 and N3004. (Item #: 112189, Ref: N1585) $24.70

Cooling System

Radiator Mounting Pads, Pack of 2 - This pack of 2 radiator mounting pads is for tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 3000, 4000, 5000, 7000, 2600, 3600, 4600, 5600, 6600, 7600, 6700, 7700, 2310, 2610, 3610, 3910, 4610, 5610, 6610, 7610, 6710, 7710, 7810, 8010. Replaces B9NN8125A, 81811605 and C5NN8125A. Two are used per tractor on the bottom of the radiator. (Item #: 109978, Ref: 180705M1) $2.50

Water Pump - This water pump comes with gasket, without backplate. It is completely new, from the seal to the housing. It fits multiple Ford / New Holland Tractor models. TB120, 7810 (2-1-88 >), 7810S (1-1-94 >), 8010 (After Serial Number 800001M). Replaces EJPN8A513BA, EJPN8A513BA, VPE1038, 81863835, 83926130, 83961310, SW06499 (Item #: 108528, Ref: FAPN8A513CC) $217.65

Water Pump Gasket - Used on multiple Ford models built 1965 and later. Replaces original part numbers D6NN8507A, E5NN8507AA, E5NN8507AB, C5NE9513A. (Item #: 117437, Ref: E5NN8507AB) $1.00

Water Pump Gasket - This is the Water Pump to Pump Housing Gaskets used in Ford/New Holland equipment, 1965 and later. It replaces original part numbers 83959398, E6NN8513AA. (Item #: 117438, Ref: E6NN8513AA) $3.20

Drive Train

Ball Bearing Assembly - The is an open, deep groove bearing. It has applications in transmissions as well and is CAR MFWD front ends. It measures: 60mm (2.362 inches) inside diameter, 110mm (4.33 inches) outside diameter, 22mm (0.866 inches) wide. Replaces manufacturer part numbers: 6212, 32306, ST269A, 3114946R91, K261879, 83930318, 20141040, CAR25813, 28996590, C5NN7127B, 81804781, 80996590, 20140, 253072272, 8101-06212, 1440545X1, 24101-62124, 971043 (Item #: 156046, Ref: C5NN7127B) $19.30

Counter Shaft - This Transmission Counter Shaft is used on Ford 5000, 5100, 5200, 7000, 7100, 7200, 5600, 6600, 7600, 6700, 7700, 5610, 6610, 7610. It has a 2.065 inside diameter. Replaces original part numbers C9NN7111B and C5NN7111G. (Item #: 134480, Ref: C9NN7111B) $151.00

Coupling, Counter Shaft Sliding Gear - 21 teeth, 16 spline. For tractor models 2000, 2100, 2110, 2110LCG, 2120, 2150, 230, 2300, 230A, 231, 2310, 233, 234, 250C, 2600, 260C, 2610, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 333, 3330, 334, 335, 340, 3400, 340A, 340B, 3430, 345C, 345D, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4110LCG, 4130, 4140, 4190, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 445C, 445D, 4500, 455, 4600, 4610, 4630, 4830, 5000, 5030, 515, 530, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 5600, 5610, 5610S, 5640, 5700, 5900, 655, 655A, 6600, 6610, 6610S, 6640, 6700, 6710, 7010, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810S, 7840, 8010, 8240, TS100, TS90 all with 8 speed transmission. Replaces C5NN7106B, C7NN7106E, C5NN7102F, D2NN7106B, C5NN7106D, 81819184, 81826589, 81823632, 81813478, E0NN7106BA, 83934545 (Item #: 170135, Ref: E0NN7106BA) $65.00

Differential Lock Coupler - Used in Ford equipment with differential lock, 1965 and later, this part replaces Ford / New Holland part numbers: C5NN4N064A, 81812261, 81871527. This part is used on the following models: 250C, 260C, 2810, 2910, 3000, 3055, 3230, 335, 340, 340A, 340B, 3430, 345C, 345D, 3550, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4140, 4190, 420, 4200, 4330, 4340, 4400, 445, 445A, 445C, 445D, 450, 4500, 455, 455C, 455D, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 515, 5190, 5200, 532, 5340, 535, 540, 545, 550, 5500, 555, 5550, 555A, 555B, 555C, 555D, 555E, 5600, 5610, 5610S, 575D, 575E, 5900, 650, 6500, 655, 655A, 655C, 655D, 655E, 6600, 6610, 6610S, 6700, 6710, 6810, 7000, 750, 7500, 755, 755A, 755B, 7600, 7610, 7610S, 7700, 7710, 7810, 7810S, 7910, 8010, 8210, TS100, TS90 (Item #: 180499, Ref: C5NN4N064A) $105.00

Drive Plate Bearing - Measuring 2.68 inches outside diameter, 1.43 inches inside diameter, 0.59 wide. It is listed here as a Transmission Drive Plate bearing but has other applications. Replaces OEM numbers 47508382, 81811675, 81816675, C5NNN779A, C5NN779B, 83992560, F0NN779AA, C5NNN779B, F0NNN779AA. Used on Ford 4400, 4500, 4830, 5000, 5030, 5100, 5110, 5190, 5200, 5340, 5550, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7410, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8000, 8010, 8030, 8100, 8200, 8210, 8240, 8340, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9200, 9600, 9700, TS100, TS110, TS80, TS90, TW10, TW15, TW20, TW25, TW30, TW35, TW5 (Item #: 108005, Ref: C5NNN779B) $15.20

Gear, 1st and 5th - Used on 8 speed transmissions on Ford models 5000, 5100, 5190, 5200, 5340, 5600, 5610, 5640, 5700, 5900, 6600, 6610, 6610S, 6640, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7840, 8010, 8240, TS100, TS90. This gear has 46 and 28 teeth. It replaces OEM numbers 83946988, 82987560, E6NN7N100BA, E2NN7N100AA, 83959993, D2NN7N100A, 81826587 (Item #: 179401, Ref: E6NN7N100BA) $171.00

Gear, 2nd and 6th - Gear has 28 and 43 teeth. It is used is some 8 speed transmissions of Ford Tractors. Replaces OEM numbers C5NN7N101B, D2NN7N101A, 81813520, E2NN7N101AA, 81826588, C5NN7N101D, E6NN7N101BA, 82987561, 83959996, 83945994 (Item #: 179205, Ref: E6NN7N101B) $128.61

Gear Shift Boot - This Gear Shift Boot can be used on multiple Ford/New Holland Tractors built 1965 and later. The top holes is 5/8 inch and the bottom hole is 2 1/2 inches. It replaces original part numbers C5NN27534, C5NN275394, C5NN7277D, D4NN7N309A, 82007346. (Item #: 164365, Ref: C5NN27534) $3.60

Gear Shift Cover Gasket - This Gear Shift Gasket is used with C5NN7222 Gear Shift Assembly. Replaces 83958298, D2NN7223A, E0NN7223BA, 81829229, E5NN7223AA (Item #: 164338, Ref: E5NN7223AA) $4.50

Gear Shift Knob - This Gear Shift Knob fits 5/16 inch x 24 thread and approx. 1.299 inch diameter. It replaces original part numbers E440GB9, 81800669 (Item #: 121228, Ref: E440GB9) $2.90

Input Drive Shaft - This Input Drive Shaft, is hollow. It has a Length of 19.22 inches, 10 Spline, 20 Teeth. Spline Flange is 1.46 from end. Replaces original part numbers E2NN7017EA, 83946987. (Item #: 179309, Ref: E2NN7017EA) $234.00

Input Shaft Seal - The measurements on the seal are 2.283 inch inside diameter, 3.130 inch outside diameter, 0.375 inch wide. This seal replaces OEM numbers: D9NN7048BA, D6NN7048B, D2NN7048A, 81826482, C5NN77047A, D9NN7048AA, 83924926, 83912260, 83924160. Used on Ford 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 8010, 8240, TS100, TS90 (Item #: 172928, Ref: D9NN7048BA) $6.20

Main Shaft - 30/18 teeth. For tractor models (5000 with dual power 6/1973 and up), (5600, 6600, 6700, 5610, 6610, 6710, 6810 with dual power), 7810, 8010, 5610S, 6610S, 7610S, 7810S, (5640, 6640, 7740, 7840, 8240, TS90, TS100, TS110 with 8 speed less dual power, 16 speed with dual power). Replaces E7NN7C094AA. (Item #: 182728, Ref: 82983066) $360.00

Main Shaft Connecting Coupling - For tractor models 2000, 3000, 8N, NAA, Jubilee and others all with 4 speed transmission. Main shaft connecting coupling has 21 teeth, 16 spline. Replaces 83959995, 957E7106 (Item #: 172715, Ref: E6NN7106AA) $68.00

Output Shaft Bearing - Measures 41.3mm inside diameter, 73.4mm outside diameter and 19.8mm wide. Replaces: LM501349/501310, 663558R1, 81277C1, 81278C1, GHB142, 663557R91, 86512015, 5132342, 4999261, WAA4221A, 860270, 860297, WAA4222A, WAA4220A, 05132342, 67370, 67371, 644321, 81803417, 860299, 860301, 860302, 860304, 81803412, 860295, 86512015, 5132342, 83992412, 81854761, 81854361, JD8237, JD8902, 663556R91, 663558R1, 86512015, 663557R91, 109706396, GHB142, MBU1044, 113571M1 (Item #: 150013, Ref: 86512015) $14.60

Output Shaft Gear - Gear has 28 and 49 Teeth. It is used an many Ford / New Holland Models with 8 speed and 6x4 Manual Reversing Transmissions. Replaces OEM part numbers C5NN7145A, 83960022, E6NN7145BA, 81804812, E6NN7145AA (Item #: 165990, Ref: E6NN7145AA) $358.00

Rear Axle to Center Housing O-Ring - This Rear Axle to Center Housing O-Ring is used on multiple Ford / New Holland Models. It is number 1 in the image. This O-Ring should always be replaced when changing brake disc on oil immersed systems. 13.50 inch inside diameter x .139 inches thick. Replaces 379313S91, 83417133, VPJ7202, 47P3852 (Item #: 113943, Ref: 379313S91) $6.40

Reverse Idler Shaft - Used on Ford / New Holland 4 and 6 cylinder models with 8 speed transmissions, this shaft is 3.5 inches long. Replaces OEM numbers C7NN7140C, 81817885 (Item #: 182891, Ref: C7NN7140C) $48.30

Secondary Countershaft - With a teeth count of 16-35-16, this Secondary Countershaft replaces Ford part numbers D9NN7B281CA, 81822961, C9NN7113B. It is used on Ford models: 345C, 345D, 445, 5000, 5100, 5110, 5190, 5200, 5340, 545, 545C, 545D, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 8010, 8240 (Item #: 166071, Ref: C9NN7113B) $100.98

Secondary Output Shaft Bearing - With measurements of 19mm inside diameter, 53.9mm outside diameter, and 15.9mm this bearing and cone assembly replaces Ford / New Holland part numbers D0NN7N047A, D2NN7111A, 81823619, 81823620, 81822960, 82930758, E6NN7061BA, E6NN7106AA, D0NN7N048A (Item #: 182935, Ref: D0NN7N047A) $40.20

Transmission Input Shaft with Dual Power - 8.78 inches long. For tractor models (5000, 7000 1/1973 and up), 5600, 6600, 6700, 7600, 7700, 5610, 5610S, 6610, 6610S, 6710, 7610, 7610S, 7710, 8010, 6640, 7740, 7840, 8240, TS90, TS100, TS110. (Item #: 168900, Ref: D2NN7017A) $219.00

Transmission Mainshaft Front Bearing - Used in the transmissions of some of the following Ford models: 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 8010, 8240, this bearing has an inside diameter of 65mm, outside diameter of 100mm and is 18mm wide. This bearing has applications not list. It replaces OEM numbers; Ford / New Holland 81804635, C5NN7N046A, 5181866, Kubota 8101-06013. Landini SKF6013, 339673X1, Massey Ferguson 339673X1, Yanmar 24101-060134, Zetor 971014, 971019 (Item #: 182963, Ref: C5NN7N046A) $41.50

Transmission Rear Coupling - This a a paired set used on many Ford New Holland Models. Replaces OEM part numbers 83908698, 82983825, 83960027, E6NN7N072BA, D6NN7N072B (Item #: 167824, Ref: E6NN7N072BA) $91.00

Electrical System

Alternator - This is a 70 amp unit with battery sensor. D+, D+, B+ and W terminals. Has 'Lucor' connector as well under plastic terminal protector. It replaces 81863039, 82857207, E7NN10B376AB, F0NN10B376BB, 54022336, 54022336D, 63324273, LRA02690, MG0283, MG283, MAN141 (Item #: 111070, Ref: E7NN10B376BB) $131.00

Alternator New - Alternator Assembly, 70 amp. For 250C, 260C, 3230, 3430, 345C, 345D, 3930, 4130, 445C, 445D, 455C, 455D, 4639, 4830, 5030, 545C, 545D, 555C, 555D, 5610S, 575D, 655C, 655D, 6610S, 675D, 7010S, 7610S, 7810S, 8010. (Item #: 111070, Ref: E7NN10B376BB) $131.00

Ignition Switch, Keyed - This 5 position, 7 terminal ignition switch comes with 2 key. Used on many tractor models (2000, 3000, 4000, 5000, 7000 1965-1975), 8000-9700, TW10, TW20, TW30, all 1968-1982. For 2600-7700 1975-1981. For 230A, 231, 233, 234, 333, 334, 335, 420, 515, 530A, 532, 535, all 1981-1990. For 7810-8210 1982-10/1985. For TW5-TW35 to 5/1983-2/1990. 8530-8830 3/1990 and up. Starter and Heat Ignition Switch for tractors with cold start. Not for Shibaura built tractors. Replaces OEM 82849085, 81871583, 81838692, 83999543, 83902803, E7NN11N501AB, D3NN11N501A, D5NN11N501A, C5NN11N501A, E7NN11N501AC, 83959710, 83976890, E7NN11N501AA, E8NN11N501AA (Item #: 116913, Ref: E7NN11N501AB) $9.30

Voltage Regulator - This is a 12v, 14.4 volt set, A-circuit, with battery temp sensor. Fits alternators: E7NN10B376AB, E7NN10B376BB, E3NN10B376AD, 81863039, 81863039, 81868798. Fits on the back of Lucas/Marelli alternators. Replaces E8NN10316AA, 83981529 (Item #: 182960, Ref: E8NN10316AA) $37.70

Engine Bearings

Flywheel With Ring Gear - This Flywheel with Ring Gear is used with 13 inch clutches. It has 128 teeth. Used on engines: BSD332, BSD333, BSD444, BSD444T Replaces F1NN6375AA, 81871636 (Item #: 159169) $700.00

Engine Gaskets

Crank Seal, Front - Fits 3, 4 and 6 Cylinder Engines in: 2000, 2600, 3000, 3600, 3610, 3910, 4000, 4600, 4610, 5000, 5600, 5700, 6000, 6600, 6610, 6640, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 8000, 8160, 8200, 8240, 8260, 8340, 8360, 8560, 8600, 8700, 9000, 9200, 9600, 9700, TS80, TS90, TW10, TW20, TW30. 60MM X 89MM X 12MM. Replaces 81813951, 81815927, 83999512, 1815927, F0NN6700CA, 83908809, 87800348, 87800696, 87802755, C5NN6700A, D5NN6700A (Item #: 106352, Ref: D5NN6700A) $8.50

Engine Parts

Crankshaft Pulley Spacer - Replace Ford part numbers F0NN6B306AA and 87800706, this space (collar) measures 44mm inside diameter, 60mm outside diameter and 21mm long. It is used on Ford / New Holland models: 345C, 345D, 545C, 545D, 555C, 555D, 555E, 575D, 575E, 650, 655D, 655E, 675D, 675E, 750, 755, 755A, 755B, 6640, 7740, 3230, 3430, 3930, 4130, 4630, 4830, 5030, 5610, 5610S, 5640, 5900, 6610, 6610S, 6710, 6810, 6810S, 7500, 7610, 7610S, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8210, 8240, 8340, 8530, 8630, 8730, 8830, 9030E, 9030V, L865, LB110, LB115, LB115.B, LB75.B, LB90, LS180, LS190, LX865, LX885, LX985, TB100, TB110, TB120, TB80, TB90, TS90, TS100, TS110, TS115, TW5, TW15, TW25, TW35 (Item #: 168951, Ref: F0NN6B306AA) $27.90

Crankshaft Pulley Spacer - Used on many Ford / New Holland models, 1965 and later, this is a keyed spacer. It fits behind the crankshaft pulley. Replaces OEM part numbers 83995427, 1811427, 81811427, C5NE6B306A, C5NE6C306A (Item #: 154924, Ref: C5NE6B306A) $20.30

Ring Gear, Flywheel - This ring gear measures 16.115 outside diameter, 14.52 inside diameter, .625 width and has 128 teeth. For gas and diesel models 2000, 3000, 4000, 5000, 6000, 7000, all 1965-1975. For 2600, 3600, 4600, 5600, 6600, 7700, all 1975-1981. For 5000 gas 6/1971-1975. For 3230, 3430, 3930, 4130, 4430, 4830, 5030, 3/1990 and up. Also used on many industrials and later models. Replaces C5NE6384AA, 83949153, 82954183, 9710967, 500791, 18042303, 80873368, 873368, 3949153. Starter Flywheel Ring Gear. (Item #: 111310, Ref: E2NN6384AA) $39.20

Fuel System / Air Intake

Air Cleaner Dust Collector - This Air Cleaner Dust Collector Valve has a 3 inch inside diameter. It is used on multiple Ford/New Holland models. It replaces original part numbers 81870839, D2NN9C673B, F0NN9C673AA. (Item #: 121925, Ref: T23262) $6.30

Fuel Cap, Vented - 2-7/8 inch outside diameter, silver finish, 1-3/4 inches edge of tang to edge of tang, vented, includes gasket. For tractor models 4830, 5000, 5030, 5100, 5110, 5190, 5200, 5340, 5530, 5600, 5610, 5640, 5700, 5900, 6000, 6000 Commander, 6410, 6600, 6610, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7740, 7810, 7840, 7910, 8000, 8010, 8210, 8240, 8340, 8400, 8530, 8630, 8700, 8730, 8830, 9000, 9200, 9600, 9700. (Item #: 184806, Ref: C5NN9030D) $8.90

No
Picture
Fuel Sending Unit - This Fuel Sending Unit is mounted with 6 bolts and is for 4 cylinder engine. For 5600, 6600, 7610, 5610S, 6610S, 7610S, 7810, 5110, 531, 532, 5900, 6410, 6600 and 8010S. Also replaces D8NN9A316LA. (Item #: 119735, Ref: D8NN9A316LB) $82.00

Precleaner Assembly - For tractor models 7000 10/1971-1974, 7600 and 7700 1975-1981, (2310, 2610, 2810, 2910, 3610, 3910, 4110, 230A, 234, 334, 335, 530A, all 1981-2/1990), (5610, 6610, 6710, 7610, 7710, all 1981-1991), (7810, 7910, 8210, 8530, TW5, all 1982-10/1991). Precleaner Assembly, dry for 3 inch pipe. 10 Inch Diameter. Replaces 82926173, 81821684, C9NN9A660C (Item #: 112379, Ref: C9NN9A660C) $34.20

Hydraulic System

Hydraulic Filter Spin-On, Intake - Outside diameter 5.38 inch, inside diameter 1.75 inch, height 9.62 inch. For tractor models 6510S, 6610S, 7610S, 8010, 5640, 6640, 7740, 7840, 8240, 8340, 8160, 8260, 8360, 8560. Replaces F0NNB486BB. (Item #: 126239, Ref: 82005016) $49.80

Hydraulic Plug - Hydraulic Plug measures 1 5/8 x 12 thread. For tractor models 2000, 2100, 2110, 2120, 2150, 2300, 230A, 231, 2310, 2310, 233, 234, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 333, 3330, 334, 335, 340, 3400, 340A, 340B, 3500, 3550, 3600, 3610, 3900, 3910, 4000, 4100, 4100, 4110, 4140, 4190, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 450, 4500, 4600, 4610, 5000, 5100, 5110, 515, 5190, 5200, 530A, 531, 532, 5340, 535, 540, 540A, 540B, 545, 545A, 550, 555, 555A, 555B, 5600, 5610, 5900, 6410, 655, 655A, 6600, 6610, 6810, 7010, 7100, 7200, 745, 7600, 7610, 8000, 8010, 8200, 8400, 8600, 8700, 9000, 9200, 9600, 9700, DEXTA, FMD, SUPER DEXTA, TB100, TB110, TB120, TB80, TB85, TB90, TW10, TW20, TW30. Replaces 83911792, D6NN7222A, 81804565, 83911793, D6NN7222B. VERIFY DIMENSIONS OR OEM BEFORE ORDERING. (Item #: 113703, Ref: 957E7010) $15.10

Hydraulic Pump - This is a Gear Type Pump. It will mount to the engine in the same location as a Piston Style Pump, but the hydraulic lines will have to be changed. For tractor models: 231, 233, 333, 531, 2600, 3600 1975-1981, 234, 2310, 2610, 3610 1981-3/1983, 5610, 6610, 6710, 7610, 7710 1981-9/1985, 7210, 8210 1982-10/1991, TW5, TW15, TW25, TW35, all with Engine Mounted Pump. (3500, 3350, 4400, 4500, 3000, 3055, 3100, 3120, 3150, 3300, 3310, 3330, 3400, 4000, 4100, 4200, 4330, 4340, all 1965 to 9/1969 w/ Ind PTO). Uses E4NN911AA gasket, not included. Used with filter D6NNB486A with vertical exhaust or D8NNB486EA with horizontal exhaust. Hydraulic Pump also replaces 83996272, 83996336, E1NN600AA, E1NN600AB, E2NN600AB, C5NN600AA, D3NN600A, D3NN600H, D4NN600B, ESL11276, E1NN600AA-E, E1NN600AB, VPK1014, 81836735, 81844738, 83900640, 83928509, 83996272. YTO E1NN600AB (Item #: 155909) $375.51

Hydraulic Pump Gasket - This gasket is used to mount Engine Mounted Hydraulic Pumps on many Ford Tractors, including E1NN600AB Pump. Replaces original part numbers 83948101, E4NN911AA. (Item #: 162462, Ref: E4NN911AA) $2.00

Lift Cylinder Safety Valve - This Lift Cylinder Safety Valve has 3/4 x 16UNF Right Hand Threads. It is used on Ford / New Holland 231, 2310, 233, 234, 250C, 2600, 260C, 2610, 2810, 2910, 3230, 333, 334, 335, 340, 340A, 340B, 3430, 345C, 345D, 3600, 3610, 3900, 3910, 3930, 4100, 4110, 4130, 420, 445, 445A, 445C, 445D, 4500, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 515, 5200, 531, 532, 5340, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7410, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8210, 8240, 8340, 8530, 8630, 8730, 8830, TS100, TS90, TW15, TW25, TW35, TW5. Replaces 81838679, D3NN984C, D5NN984A, 83911832 (Item #: 170948, Ref: D5NN984A) $40.70

Lights

Light Switch, Rotary Type - This Rotary Type Light Switch is used on many Ford / New Holland Tractors and Industrials, 1965 and later. It replaces original part numbers C5NN11654A, C5NN11654D, C7NN11654B, C7NN11654C, D5NN11654B, E7NN11654AA, 83959708, D10026500, 83959708, 81818781, 81818408, 83905863. (Item #: 121197, Ref: E7NN11654AA) $13.20

Miscellaneous

Thermostart Plug - Intake Manifold Heater. For tractor models 230A, 234, 250C, 260C, 2610, 2810, 2910, 3430, 345C/D, 3610, 3910, 3930, 4110, 445/A/C/D, 4610, 4630, 545/A/C/D, 5610, 6610, 6710, 7610, 7710, 7810, L783, L785, 3230, 4130AP, 4830, 5030, 5640, 6640, 7010, 7740, 7840, 8010, 8240, 8340, L865, L885, LX865, LX885, 334, 335, 550, 2310N, 530A, 5110, 6810, 8160, 8260, 836, 856. Replaces 80858863, 83933675, 87800843, C5NE9A436A, E1NN9A436AA, 603922 (Item #: 118792, Ref: 3583543M2) $11.80

Oil System

Oil Pan Drain Plug - This 3/4 inch Oil Pan Drain Plug is for Ford tractor models: 230A, 231, 233, 234, 333, 334, 335, 420, 445, 445A, 450, 515, 531, 532, 535, 540, 540A, 540B, 545, 545A, 550, 555, 555A, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 755, 755A, 755B, 2000, 2600, 2910, 3000, 3230, 3400, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4110LCG, 4130, 4400, 4500, 4610, 4630, 4830, 5000, 5030, 5500, 5550, 5600, 5610, 5900, 6500, 6600, 6610, 6700, 6710, 7000, 7500, 7600, 7610, 7700, 7710, 7810, 7810S, 7840, 7910, 8000, 8010, 8160, 8210, 8240, 8260, 8340, 8360, 8530, 8560, 8600, 8630, 8670, 8700, 8730, 8770, 8830, 8970, 9000 1970 and up. Uses C9NN6734A washer, not included. Replaces C9NN6730B. (Item #: 140610, Ref: C9NN6730B) $3.70

Oil Pan Drain Plug Washer - Used with C9NN6730B 3/4 inch Oil Pan Drain Plug. Fits models: 230A, 231, 233, 234, 333, 334, 335, 420, 445, 445A, 450, 515, 531, 532, 535, 540, 540A, 540B, 545, 545A, 550, 555, 555A, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 755A, 755B, 2000, 2110LCG, 2600, 2810, 2910, 3000, 3230, 3400, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4110LCG, 4130, 4400, 4500, 4610, 4630, 4830, 5000, 5030, 5500, 5550, 5600, 5610, 5900, 6500, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 7810, 7810S, 7840, 7910, 8000, 8010, 8160, 8210, 8240, 8260, 8340, 8360, 8530, 8560, 8600, 8630, 8670, 8700, 8730, 8770, 8830, 8970, 9000. (Item #: 140611, Ref: C9NN6734A) $1.60

Oil Pressure Switch - This oil pressure switch is made with 2 types of connectors and you may receive a typical space connector or a round connector. Whichever wire connector you have on your tractor will fit either switch. The are interchangeable. For tractor models 2000, 3000, 4000, 5000, 7000, 8000, 8600, 8700, 9000, 9600, 9700, 2600, 3600, 3900, 4100, 4600, 5600, 5900, 6600, 6700, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4110, 4610, 5610, 5610S, 6610, 6610S, 6710, 6810, 7610, 7610S, 7710, 7810, 7810S, 7910, 8010, 8210, 3230, 3430, 3930, 4130, 4630, 4830. Replaces 81873524, F1NN9278AA, D8NN9278AA. (Item #: 153774, Ref: D8NN9278BD) $5.90

PTO / Driveline

Driven Gear - This is the 540 RPM Driven Gear for a two speed. For 540/1000 RPM two speed Independent PTO System. It has 70 and 8 teeth. Replaces 83927911, E0NNA726AB, E0NNA726AD. (Item #: 163803, Ref: E0NNA726AD) $316.00

Gear, IPTO Driven - Used in two speed, independent PTO tractors, this gear is used in the 1000 RPM setting. It has 8 splines and 84 helical teeth. Used on Ford / New Holland models: 5110, 5610, 5610S, 5640, 5900, 6410, 6610, 6610S, 6640, 6710, 6810, 7010, 7410, 7600, 7610, 7610S, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8210, 8240, 8340, TS100, TS110, TS120A, TS90. Replaces E0NNA726BA, 83926452 (Item #: 163802, Ref: E0NNA726BA) $360.00

PTO Driven Gear - This gear has 20 and 41 teeth. It is used with 540/1000 RPM two speed independent PTO. Replaces original part numbers E0NN745AA, 83924763. (Item #: 166637, Ref: E0NN745AA) $267.00

PTO Drive Plate - This PTO Drive Plate has 20 splines. If you need 15 splines, order C5NNN777A. Used on 5000, 5600, 5610, 5610S, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7600, 7610, 7610S, 7700, 7710, 7810, 7810S, 7910, 8000, 8010, 9000. Replaces E1NNN777AB, E2NN777AA (Item #: 104264, Ref: E1NNN777AB) $79.00

PTO Drive Shaft - PTO Drive Shaft 22 spline. For tractor models (5610, 6610 11/91-> 8 speed Non synchro), 5610S, 6610S, 7610S, 7810S, 7010, 8010, (5640, 6640, 7740, 7840, 8240, 8x2 OR 16x4 Ttans), TB80, TB85, TB90. (Item #: 155573, Ref: E9NN7A684AA) $171.00

PTO Output Shaft Seal - Note that two size seals were used on the output shaft on many of the models listed. Verify measurements or OEM number before ordering. This seal measures 74.62mm inside diameter x 95.24mm outside diameter x 9.5mm wide (3.75 inches x 2.85 inches x 0.375 inches wide). Used on Ford 3600, 4600, 5000, 5100, 5110, 5190, 5200, 532, 5340, 5600, 5610, 5700, 5900, 6410, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7600, 7610, 7700, 7710, 7810, 7910, 8000, 8010, 8210, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9600, 9700, TW10, TW15, TW20, TW25, TW30, TW35, TW5. Replaces Ford / New Holland part numbers D9NNN710BB, D9NNN710B, 83944032 (Item #: 189274, Ref: D9NNN710B) $12.10

PTO Output Shaft Seal - Note that two size seals were used on the output shaft on many of the models listed. Verify measurements or OEM number before ordering. This seal measures 74.6mm inside diameter x 95.6 outside diameter x 12.5mm wide (3.75 inches x 2.85 inches x 0.56 inches wide). Used on Ford / New Holland 3600, 4600, 5110, 532, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 6810S, 7010, 7410, 7600, 7610, 7610S, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8200, 8210, 8240, 8340, 8530, 8600, 8630, 8670, 8670A, 8700, 8730, 8770, 8770A, 8830, 8870, 8870A, 8970, 8970A, 9200, 9700, TS100, TS100 Brazilian, TS110, TS110 Brazilian, TS115, TS120 Brazilian, TS80, TS90, TV140, TW10, TW15, TW20, TW25, TW30, TW35, TW5. Replaces 81819768, 83955173, 9823545, 89823545, D9NNN710BC, D9NN710BC (Item #: 128143, Ref: 9823545) $26.80

PTO Piston Return Spring - Replacing Ford / New Holland part numbers 81871420, 83935173, C0NN7C151A, 9823824, D7NNC732A, 81804819, this Spring is used in tractors with independent PTOs. Used on Ford / New Holland models: 5000, 5100, 5110, 5190, 5200, 5340, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7410, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8000, 8010, 8210, 8240, 8340, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9600, 9700, TS100, TS90, TW10, TW15, TW20, TW25, TW30, TW35, TW5 (Item #: 124549, Ref: D7NNC732A) $20.40

PTO Shaft Support - Support, for PTO Shaft and Drive Clutch Valve. DOES NOT have relief oil hole in support. For tractor models 5000, 5600, 5610, 5700, 5900, 6600, 6610, 6700, 6710, 7000, 7600, 7610, 7700, 7710. Replaces original part numbers C2NNN776A, D2NNN776A and 81826819. (Item #: 111897, Ref: D2NNN776A) $23.30

Sheet Metal / Body Parts

Grill - Metal Replacement Grill for 2310, 2610, 2810, 2910, 3430, 3610, 3910, 3930, 4110, 4130, 4610, 4630, 4830, 5030, 5110, 5610, 6410, 6610, 6810, 7610, 7810, 8010. Replaces E0NN8200AA, E0NN8200AA27G and E0NN8200AA27V. This grill is for use on tractors with external mounted headlights. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 111517, Ref: E0NN8200AA98M) $86.00

Grill, With Light Holes - Metal Replacement Grill For 2310, 2610, 2810, 2910, 3430, 3610, 3910, 3930, 4110, 4130, 4610, 4630, 4830, 5030, 5110, 5610, 6410, 6610, 6810, 7610, 7810, 8010. With light holes towards the bottom of the grill. Mounting bolt holes are 5 1/2 inches from the top. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 112426, Ref: E1NN8200AA) $82.00

Steering

Axle Pivot Bushing - On Carraro 4WD front ends, this the outer most bushing on the pivot assembly. Measures 135mm outside diameter, 124mm inside diameter, 42 mm wide. This part replaces OEM part numbers CAR1234751, CAR123475, 83971641, 9968007, 83957129, 337255A1 (Item #: 156147, Ref: CAR1234751) $32.30

Axle Support Bushing - Used on Carraro 4WD front ends, this bushing measures 4.921 inches outside diameter, 4.527 inches inside diameter and is 1.653 inches long. Replaces OEM numbers K965756, K965265, 1-33-241-048, 9967992, K965265, CAR101575/1, CAR123477, CAR1015751, 9967992, 83930079, 83930554, R113767, 3541395M1 (Item #: 156131, Ref: CAR1015751) $92.58

Cross and Bearing Kit - A= 1.18 inch, B= 1.18 inch, C= 3.62 inch, D= 3.62 inch. For tractor models 5110, 5610, 5610S, 6410, 6610, 6610S, 6810, 6810S, 7010, 7610, 7610S, 7710, 7810, 7810S, 7910, 8010, 8210 all with MFWD. Replaces E7NN4635AA. (Item #: 156127, Ref: 83959516) $48.40

Front Axle - Differential Housing Bushing - The measurements on this bushing are: 4.525 inches outside diameter, 4.127 inches inside diameter, 1.730 inches long. This bushing is used on Carraro 4WD front end. Replaces OEM numbers 101565, K965266, CAR1015651, 83945601, CAR101565/1, CAR123478, 83930062, 9967993, R113766, 3541396M1, 040953R1 (Item #: 156132, Ref: CAR1015651) $79.00

Front Axle Oil Seal - Used on some Carraro 4WD front ends, the seal replaces OEM numbers 153326217, 5122548, 5105932, CAR115715, 83944350, K262811, K395039, EQ501510 (Item #: 156134, Ref: CAR115715) $8.70

Front Axle O-Ring - Many Carraro 4WD front axle equipped use this o-ring at the front of the pivot assembly. This part replaces OEM numbers 83957130, 83959520, CAR28556, N805193S91, 85807958, K965267, 28103 (Item #: 156146, Ref: CAR28556) $1.20

Front Axle Sleeve - Used on the pivot pin assembly on Carraro 4WD front axles, this bushing measures 115mm inside diameter, 125mm outside diameter, and 44mm wide. Replaces OEM numbers 09968010, 83957128, 83961191, 337253A1, 9968010, CAR123476, CAR124592 (Item #: 156145, Ref: CAR124592) $75.00

Front Axle Thrust Washer - Used in some Carraro Mechanical Four Wheel Drive front axles, this part replaces CAR115776, 47109296, CAR123478, 83944351, 9967994, K395022 (Item #: 156133, Ref: CAR115776) $23.90

Half Shaft Bushing - Many Carraro Mechanical Four Wheel Drive front axles use this inner half shaft bearing. This part replaces OEM numbers 09968000, 9968000, 87313791, 83952334, CAR118547, K395019 (Item #: 156140, Ref: CAR118547) $11.02

Half Shaft Bushing - This bushing is closest to the wheel on the Carraro front axle shaft. Replaces OEM numbers 09968019, 109972, 5194292, CAR109972, 83930156, 9968019, 1967535C1, 05194292 (Item #: 156143, Ref: CAR109972) $9.60

Hub Seal, MFWD - Extensively used on Carraro mechanical four wheel drive front axles, this hub seal measures 149mm (5.86614 inches) x 176mm (5.86614 inches) x 16mm (0.629921 inches). Replaces OEM numbers 9968085, K395102, 47108806, 83996064, 82920209, 294169A1, 247877A1, 130182A1, 1349265C1, CAR126324, CAR47705, 3225110, 0003225110, 82920209, 3996064, 83996064, 83957862, 9968085, 153326219, 153326621, 1349265C1, 153326301, 09968085, 83952509, 83952530, CAR118556, CAR126324, CAR47705, CAR126390, 3501510M1, 3475598M1, 3475533M1, 3523062M1, 3541510M1 (Item #: 157753, Ref: 247877A1) $60.00

King Pin - Mechanical Four Wheel Drive, Carraro front ends use these king pins at the hubs. This king pin replaces OEM part numbers CAR115729, K395035, 83957144 (Item #: 156166, Ref: CAR115729) $46.98

King Pin Thrust Bearing - Used on several Carraro 4WD front ends, this 2 piece bearing set replaces OEM numbers N14373, 47109506, 3523057M1, 47895578, 123726, 137700410834, 153326668, 1964243C1, 14373, 83982416, 83944349, 87523063, K395040, 87521218, 47123701, 9968002, CAR123726, CAR115714, 3541402M1, 3475530M1, 3523057M1, EQ501557, ER123726 (Item #: 156136, Ref: CAR123726) $26.30

Power Steering Cylinder End - Power Steering End right hand (inner), .875 inch-14 thread female, 3.625 inches long to center of post. Tractors: 3010S, 4010S, 5100, 5110, 5600, 5610, 5610S, 5900, 6410, 6600, 6610, 6610S, 6710, 6810, 6810S, 7010, 7100, 7600, 7610, 7610S, 7810, 7810S, 8010. Verify Part number to ensure proper fit. (Item #: 100683, Ref: E3NN3B539AA) $32.80

Power Steering Pump Repair Kit - Kit repairs the following pumps: E6NN3K514EA, D8NN3K514KC, E0NN3K514AB, and E6NN3K514AB. Note, this kit contains 1 -Double Lip Seal. If your pump uses 2 - Single Lip Seals, use part number DHPN3A674B (Item #: 187034, Ref: 83910651) $13.20

Reservoir Cap, Power Steering Pump - Used on E6NN3K514EA, D8NN3K514GC, C9NN3A674D Power Steering Pumps. For tractor models 231, 233, 2600, (3500, 3550 5/1970 to 1975), 3600, (4100 4/1970 to 1975), (420, 4600, 5600, 6600, 7600 1975 to 1981), 4600SU, (5100, 7100 7/1970 to 1975) and others. (Item #: 121241, Ref: D2NN3A006B) $3.60

Roller Bearing - Used in many Four Wheel Drive Systems, this bearing measures 109.5mm (4.311 inches) inside diameter, 158.8mm (6.25 inches) outside diameter and 21.2mm (o.834 inches) wide. Replaces OEM numbers ZP0735370150, 81676C1, 84592016, 47724311, 5133737, 83952531, K395101, H1482196, CAR118370, 9967690, CAR045180, CAR142088, K395101, ZP0735370150, 83952531, 47724311, 5133737, 84592016, 6914441, 9967690, 83985020, 89967690, CAR118370, 81676C1, 05133737, 47724311, H1482196, K395101, 81676C1 (Item #: 156047, Ref: JD10249) $78.00

Seal, Spindle Pin - For tractor models 1801, 250C, 260C, 3000, 340, 340A, 340B, 345C, 345D, 3500, 3550, 4000, 4040, 4140, 420, 4400, 445, 445A, 445C, 450, 4500, 455, 5110, 515, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 5610, 6410, 655, 655A, 6610, 6610O, 6810, 7010, 4610O, 8010, TT55, TT75. (Item #: 128511, Ref: TDBA3125A) $2.90

Spindle Repair Kit, Less Spindle - 1.23 inch pin, less spindle, with unfinished bushings. For tractor models 7010, 8010, 250C, 260C, 340B, 345C, 345D, 445A, 445C, 445D, 450, 540B, 545A, 545C, 545D, 555A, 555B, 655A. (Item #: 125386, Ref: EFPN3115A) $102.00

No
Picture
Spindle Repair Kit, With Spindle - 1.23" pin, with spindle, finished bushings. For tractor models 7010, 8010, 250C, 260C, 340B, 345C, 345D, 445A, 445C, 445D, 450, 540B, 545A, 545C, 545D, 555A, 555B, 655A. (Item #: 178370, Ref: S.75083) $457.00

Steering Joint - This Steering Joint is 7.040 over all length. The Inner Thread is M20 X 1.5 RH Thread. The Outer Thread is M18 X 1.5 LH Thread. Replaces 1966127C1, 83957148, CAR49006, 1-33-743-602, 112508A1 (Item #: 104634, Ref: CAR49006) $59.00

Steering Motor - This Steering Motor is used on Ford/New Holland Models: 3010S, 4010S, 5010S, 7010, 7810S, 8010, TB100, TB110, TB120, TB80, TB85, TB90, TT55, TT65, TT75. It replaces original part numbers 82851795 and F2NN3A244BA. (Item #: 156693, Ref: 82851795) $619.00

Steering Sector Shaft Seal - Two of these felt seals are used per tractor. It measures 1.470 inch outside diameter, 0.925 inch inside diameter and 0.360 inch thick. Replaces 81826045, 8N3586, D2NN2N171A, 86553476, C5NN3586A (Item #: 124494, Ref: 8N3586) $2.10

Steering Wheel - This Steering wheel is 15 inch diameter with a 36 spline center hub. PVC grained cover material with covered spokes. For tractor models 2310, 2600, 2610, 2810, 2910, 3230, 3430, 3600, 3610, 3900, 3910, 3930, 4110, 4130, 4600, 4610, 4630, 4830, 5110, 5610, 5900, 6410, 6600, 6610, 6810, 7010, 7610, 8010, Industrials: 230A, 231, 233, 234, 333, 334, 335, 340, 530A, 531, 540, 545A, 555B. Replaces OEM number D2NN3600A, D7NN3600A. (Item #: 101427, Ref: D7NN3600A) $53.00

Thrust Washer - Used on the pivot pin assembly on some Carraro 4WD axles, this thrust washer replaces OEM numbers 1-33-741-646, 83957128, 09968006, 83961192, 9968006, CAR124591, CAR123476 (Item #: 156144, Ref: CAR123476) $35.30

Tie Rod - This Tie Rod has 200mm (8.625 Inches) usable length shaft, 18mm X 1.5 RH thread. This is the newer style tie rod and does not use a clamp. This style requires jam nut # 87313796 currently not offered by YT. It replaces CAR48983, CAR49005, 83957757, 81878545, 81878555 (Item #: 159857, Ref: CAR49005) $60.00

Universal Joint - The measurements on this Universal Joint are 27mm cup diameter and 82mm across. Side greaser included. This Universal Joint is used on Carraro 4WD front axles. Replaces OEM numbers CAR96867, CAR116859, 3230277R1, 3216550R91, 137700420834, 1967554C1, 84512487, NH80715, 9961774, 9962244, 87760752, K965331, CAR041121, CAR116859, 83934724, 81927841, ZP1927504, ZP1927841, 3230277R1, 84512487, 83957857, AL32885, 137700000000, 3475808M91, 3475808M1, 3427352M91, 1895699M1 (Item #: 156129, Ref: CAR96867) $37.10

Universal Joint - Many mechanical four wheel drive front axles use this universal joint. This part has 27mm cup diameter and is 70.9mm across (1.063 X 2.791 inches). Replaces OEM numbers 247543A1, 81882C1, 1-33-742-629, 137700420872, 144461A1, 137700420874, 195215A1, 337260A1, D149733, B507526, CAR40869, N14156, N14411, 9968059, 84355357, 85807283, 84990205, 9970163, 85805996, 87306931, CAR40889, 81874740, 85805996, 9968059, 09968059, 1-33-742-629, CAR40825, 84355357, AL71316, RE212902, ABP3002508, 508360, ABP3004431 (Item #: 158432, Ref: CAR40825) $40.70

Wheels

$Ford 8010 Front Hub, Heavy Duty \ Industrial$
Front Hub, Heavy Duty / Industrial - Used on Heavy Duty and Industrial Front Ends. 3000, 4000 (4cyl, heavy duty front axle), 5100, 5110 (heavy duty axle), 5200, 5190, 5600 (10x16 tire), 5610 (heavy duty axle), 5700 (10x16 tire), 6600 (10x16 tire), 6610 (heavy duty axle), 6700 (10x16 tire), 6710 (heavy duty axle), 7100, 7200, 7410 (heavy duty axle), 7600 (10x16 tire), 7610 (heavy duty axle), 7700 (10x16 tire), 7710 (heavy duty axle), 8000, 8010, 9000, TW10, TW20, TW30, Industrial: 250C, 260C, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445D, 450, 515, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 1801, 3400, 3500, 3550, 4400, 4500, 4410. It uses C5NN1107F studs, and WBKFD7 wheel bearing kit, not included. Replaces OEM part number 313020. Verify part number before ordering. (Item #: 100662, Ref: 313020) $66.00

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $357.14

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Cooling System

Thermostat Housing to Block Gasket - Tractors: all 4-cylinder, 1953-1964, gas and diesel. Bolt holes measure 3/8 inch in diameter, and center to center of bolt hole spacing is 2 3/4 inches. Sold and Priced as Each. (Item #: 191970, Ref: EAF8255A) $1.04

Decals and Emblems

Decal, Fear This Ford - 12-1/2 inches x 3 inches. For all Ford tractors. (Item #: 183476, Ref: S.67825) $15.87

Sherman Transmission Instruction Plate - For Ford models with Sherman step up step down transmission. Installs under steering wheel nut. (Item #: 178113, Ref: SHERMAN) $20.60

Drive Train

Shift Cover Plate Gasket - For all models with 5-SPEED transmission built between 1955-1964. Not for tractors made overseas, such as Major, Dexta, etc. (Item #: 178105, Ref: NDA7223A) $6.70

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.80

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.30

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.80

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.30

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter Solenoid, 12 Volt - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. (Item #: 150223, Ref: DR1467) $18.70

Switch, Push Button - This 2 terminal switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch overall length. Check measurements before ordering if using as a universal part. Applications include ether switch, horn button, cold start, starter switch, and manifold heater switch. It replaces 22702, 240962, 242988, 245866, 245936, 70253322, 71191589, 72160068, VT507, 86900358, A30858, O9995AB, T18524, TG07803, TO18117, TO7803, 271179R91, 367678R91, 373611R91, 393209R91, AR46184, AR47373, AR47374, R39554, 189158M91, 767828M91, 105386A, 10A972, 1K7392C, UT2421, 1K7392A, 7A7392. (Item #: 121141, Ref: R7994) $12.50

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Pistons and Sleeves

No
Picture
Seal Kit - Seal kit, for cylinder E2NN3A540BA. Piston rod is retained with 1" snap ring and 1-3/4" threaded spanner nut. (Item #: E2NN3X-SK) $64.99

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $82.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $138.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $102.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $171.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $169.00

Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $110.21

$Ford 8010 Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10

$Ford 8010 Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$Ford 8010 Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.70

$Ford 8010 Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40

$Ford 8010 Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60

$Ford 8010 Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40

Rain Cap - This rain cap is for a 4.00 inch pipe. (Item #: 108645, Ref: R1807) $10.30

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60

Rain Cap - This rain cap is for a 5.00 inch pipe. (Item #: 108750, Ref: WC15) $16.90

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.40

Fuel System / Air Intake

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $13.00

Filter Screen and Gasket for Sediment Bowl - 1-1/2 inch outside diameter seal (for a 1 9/16 inside diameter housing and a 1 3/8 inch outside diameter screen. Measure before ordering. For tractor models (1958-1964 All with 134 cubic inch engines), 2000 4 cylinder, 501, 601, 701, (1958-1960 all with 172 cubic inch engines up to 126524), 801, 901, 1801. (Item #: 150700, Ref: ABC346) $5.40

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.50

Gauges

Ammeter, Black, Flat Bezel - For all models to 1958. Terminal type ammeter. 30-0-30. Black ring. Replaces FAD10850A. (Item #: 110410, Ref: A0NN10670A-BLAC) $8.60

No
Picture
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $58.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $37.40

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar

Drawbar Check Chain Kit - This Drawbar Check Chain Kit includes: right hand/left hand anchors, 2 eyelets, 2 chains, 4 clevis with pins, and hardware. Fits: Jubilee, NAA, NAB, 2000 3 Cylinder, 2000 4 cylinder, 2600V, 2N, 3600V, 4000 4 Cylinder, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 2030, 2031, 2100, 2110, 2111, 2120, 2121, 2130, 2131, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3110, 3120, 3300, 3330, 3600, 3610, [4030, 4130, 4140 (4 cylinder)], 4031, 4040, 4100, 4110, 4120, 4121, 4131, 9N, Industrial: 231, 233, 333, 334, 335, 1801, 1811, 1821, 1841, 1871, 1881, 230A, 3400, 3500, 530A, Dexta, Super Dexta. Replaces: 957E597, 957E596, CBPN598A, NCA597B, NCA596B. (Item #: 115051, Ref: NCA596B) $38.10

Drawbar, Heavy Duty, Heat Treated - Standard Heat Treated Drawbar Red, 30 1/2 inch L hole center to hole center, 2 1/2 inch wide, 1 1/8 inch thick (drawbar fits lift between lift arms). (Item #: 103174, Ref: 9N5182) $44.30

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.50

Link End - Plated, forged, 1-1/4 inch thread, left hand, 1 inch hole. (Item #: 180473, Ref: RE1717L) $20.40

Link End - Plated, forged, 1-1/4 inch thread, right hand, 1 inch hole. (Item #: 174507, Ref: RE1718R) $21.58

Stabilizer Arm HD - Arm only, made of alloy spring steel, for kit 231253XHD, red only. 7/8 inch hole diameter. 31 1/2 inches center to center. (Item #: 110516, Ref: 230042XHD) $15.30

Top Link - Forged Top Link, 12 inch body, Category I implement ends. Adjusts 17.5 to 24 inches overall. 3/4 inch pin holes and both eyelets are 1 3/4 inch wide. Dichromate plated. (Item #: 103162, Ref: JSA1012C) $20.80

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $33.30

Hydraulic System

Coupler Flange - FORD: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b (Item #: 108772, Ref: L36-6) $117.34

Coupler Flange - Drive flange; 3/4 inch round bore with set screw 1/4 inch x 3/8 inch. 1-15/16 inch spacing. For Morflex series 302. Replaces: L363, 191061, 1752219M91, L36-3 (Item #: 112104, Ref: 191061) $22.00

Coupler for Pump Shaft - The Hydraulic Pump Shaft Coupler is 1-1/2 Outside Diameter and 2-1/4 inches long. It 7/8 inch 13 splined inside. It replaces 1631413, 350-1631413, S340 (Item #: 114586, Ref: S340) $36.00

Coupler Hub Drive Kit - Coupler Complete, Morflex Series 302. Contains center member, 2 drive flanges with set screws, and 4 bolts with lock nuts. The center member is 3-1/8 inch diameter, with four 1/4 inch holes and 1-15/16 inch spacing.The drive flange is 3/4 inch round bore with set screw 1/4 inch by 3/8 inch. (Item #: 112067, Ref: L601-14) $124.00

Cylinder Seal Kit, For 2 inch cylinders - For TISCO side and top link replacement cylinders. Seal Repair Kit for 2 inch cylinders. For cylinder numbers: HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. (Item #: 183971, Ref: HSK2002) $23.50

Cylinder Seal Kit, For 3 inch Cylinders - For TISCO brand side and top link replacement cylinders ONLY. Seal Repair Kit for 3" cylinders. For cylinder numbers: HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. (Item #: 179480, Ref: HSK3002) $30.80

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.60

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.70

Hub - 7/8 inch, 13 spline threaded, 3-7/8 inch hole spacing. For 730 LOADER. Used with C5NNN879A hub. (Item #: 160204, Ref: 291315) $68.00

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199) $21.10

Hydraulic Pump for Loader - Part Description: Pump, Hydraulic For 730 LOADER, 735 LOADER. SPECS: CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, PORT SIZE INLET: 1-5/8 inches-12 ORB, PORT SIZE OUTLET: 1-5/16 inches-12 ORB, MOUNTING: 2 bolt SAE "B", FORD PUMP APPLICATION: 730 and 735 loaders, CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, MOUNTING: 2 bolt SAE "B", INLET: 1-5/8 inches-12 ORB, OUTLET: 1-5/16 inches-12 ORB. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inches and Maximum is 6 7/8 inches. (Item #: 127269, Ref: 7702425-29Z) $780.00

Hydraulic Pump, Front Mounted - This Hydraulic Pump is used with some 701, 702 and 703 Loaders. It is 14 Gallons Per Minute at 2000 RPM. The shaft is 3/4 inch round with a key way. Left Hand Rotation. Inlet is 1 Inch NPT. Outlet is 3/4 Inch NPT. Mounting bolt spacing 4 3/16 inches center to center. Comes with two adapters. Contains: 1-720FSO-3/4X3/4 HC4008 adapter, 1-720FSO-1X1-1/4 HC4009 adapter. This Pump may work in other loader application. Verify Specs before ordering. (Item #: 182700, Ref: L827-10X-LB) $600.00

Hydraulic Valve Kit - Valve with handles, three-spool, 2000 p.s.i. Relief, all spools tandem (4-way) spring center to neutral. (Item #: HV4030) $787.98

LBP Coupler Center - Center member. Center member. 3-5/8" O.D., four 5/16" holes, 2-1/4" bolt circle (L52-10) For tractor models 352. (Item #: 178931, Ref: 192169) $74.00

LBP Hydraulic hose Assembly - Hydraulic hose assembly. For Ford model 740 LOADER. (Item #: 179521, Ref: 7701142) $28.40

Morflex Center Member - This is a 1-302 Morflex Center member. It measures 3-1/8 inch diameter, four 1/4 inch holes, 1-15/16 inch bolt circle. Replaces part numbers 893129, 191192, L5227, 1506097M91, 1086870M1, 191192LBP, 1752218M91, L52-27 (Item #: 116952, Ref: 191192LBP) $52.92

Top Link, Hydraulic - FORD: Hydraulic top link cylinder. All ports 9/16 inch-18 O-ring boss with two adapters 9/16 inch-18 ORBM x 1/4 inch NPTM 90 degree swivel. 3 inch cylinder bore, 8 inch stroke length, 26 inch closed length, 12-7/16 inch barrel length, 1 inch rod end diameter, 1-3/4 inch rod end width, 1 inch diameter base end. (Item #: 167145, Ref: HTL3103) $280.00

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.00

Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.00

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $178.00

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $123.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.50

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $48.60

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $100.00

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.20

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights

Headlight Assembly, 12 Volt - (Single) Headlight Assembly 12-volt, blue - Sealed beam headlamp assembly in heavy gauge steel housing with Rubber bezel. Does not look like original. (Item #: 184496, Ref: L525HB-12V) $51.00

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

No
Picture
Sealed Beam Bulb, 12 Volt - Red/white combination work/tail light, 4-1/2 inch diameter. (Item #: 116014, Ref: S.52670) $24.20

Tail Light Lens - Plastic 4 inch lens for DUOLAMP with FOMOCO stamped on lens (has 2 mounting screw holes spaced 3 1/8 inches apart). Fits tractors 1953 and newer. (Item #: 178144, Ref: FDV13450A) $16.50

Miscellaneous

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Tractor Umbrella with Frame & Mounting Bracket - Blue - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without Additional Handling & Oversize Fees Apply To This Item, tools, (Item #: 161190) $119.00

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40

No
Picture
Paint, Brownish Medium Gray, 1 Quart - Ford Brownish Medium Gray was used for the same applications as TP240Ford Medium Gray. This is a lighter shade. Since the tractors did not come off the production line all the same, the darker or light shades are completely up to the desires of the customer. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184575, Ref: TP245QT) $50.00

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $69.00

No
Picture
Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20

No
Picture
Paint, Empire Blue, 1 Gallon - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100713, Ref: TP360GAL) $57.00

No
Picture
Paint, Empire Blue, 1 Quart - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100712, Ref: TP360QT) $23.30

No
Picture
Paint, Empire Blue, Spray Can - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100711, Ref: TP360SP) $7.40

No
Picture
Paint, Ford White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108135, Ref: TP470GAL) $82.00

No
Picture
Paint, Ford White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108133, Ref: TP470SP) $10.20

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100120, Ref: TP2700SP) $8.90

No
Picture
Paint, Industrial Yellow, Spray - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100723, Ref: TP760SP) $7.80

No
Picture
Paint, Light Gray, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100716, Ref: TP330GAL) $58.00

No
Picture
Paint, Light Gray, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100715, Ref: TP330QT) $20.70

No
Picture
Paint, Light Gray, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100714, Ref: TP330SP) $8.90

No
Picture
Paint, Medium Gray, 1 Quart - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100718, Ref: TP240QT) $22.10

No
Picture
Paint, Medium Gray, Spray Can - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100717, Ref: TP240SP) $8.50

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $63.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $13.98

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.80

No
Picture
Paint, Vibrant Blue, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156586, Ref: TP365GAL) $91.00

No
Picture
Paint, Vibrant Blue, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156587, Ref: TP365QT) $37.10

No
Picture
Paint, Vibrant Blue, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156585, Ref: TP365SP) $10.40

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $43.90

PTO / Driveline

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $173.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

NOTE

PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.

NOTE

PTO Overide Clutch - This 6 spline Override Coupler converts a 1 1/8 inch diameter PTO shaft to 1 3/8. It has a 1 1/8 inch female at one end and 1 3/8 inch male at the other end). Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103169, Ref: C670F) $52.00

PTO Overide Clutch - Override coupler for 1 3/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 191020, Ref: C680F) $79.00

PTO Overide Clutch - Override coupler for 1 1/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103167, Ref: C690F) $67.80

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $280.00

Seats

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57

Seat Cushion, Black - Cover with piping and Ford script logo. Fits all 1939-1964 models with a 17 inch wide steel seat pan. (Item #: 115058, Ref: 8N401BLK) $42.60

Tie-On Seat Cover - Blue and White, 19 inches wide. Deluxe with 2 inches of foam. (Item #: 101353, Ref: R1013) $35.20

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $100.00

Sheet Metal / Body Parts

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $178.00

Steering

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $48.20

Steering Wheel Spinner Assortment - Complete wheel spinner assortment: includes 2 blue, 2 green, 3 red, 2 yellow and 3 black. (Item #: 185079, Ref: WSV125A) $127.00

Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16 inches x 5/8 inch x 5/8 inch, 1 15/16 inches x 3/4 inch, 3/4 inch, and 1 3/8 inches x 1 inch x 1/2 inch. (Item #: 183427, Ref: TIERODBOOTS) $13.00

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $24.30

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $315.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. (Item #: 103768, Ref: FW60166) $92.00

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166) $70.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $17.80

No
Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $62.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $65.00

Wheel Clamp - Wheel clamp holding disc to rim for double ramp type on power adjustable rims. For 28 inch rim on tractors 2000, 3000, 4140, (10-1968 to 1975); 2600, 3600, 4100, 4600SU except Baseldon models, (1981 to 3-1990); 3230, 3430, 3930, 4130, 4630, 4830LCG, (3-1990 to -) Use with rims PAR10X18 and C5NN1050J and C5NN1050H. Also replaces 3615259M1, 70235676 and 7000000241, E5NN1043AA. (Item #: 124526, Ref: 898021M1) $18.00

Wheel Front 8X16 - Front Wheel 8 inch x 16 inch ; 6 bolt, 6 inch circle, 4.62 inch pilot. (Item #: 180445, Ref: D5NN1007A) $111.00