FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Ford 9N Tractor Parts

[Categories] [All Ford Models] [Print]

Brakes

Brake Cross Shaft Bushing - Measures 1 inch long, 1 inch inside diameter and .010 thick. Press into transmission housing {one on each side}. Sold each. For tractors: 9N, 2N, EARLY 8N {1939-1949}. Fits some later Ford models, verify measurements to ensure fit. (Item #: 178169, Ref: 782477) $7.70

Brake Lining Set - For Ford tractor models 2N, 9N, Replaces Ford OEM number 9N2021B, Includes 4 Brake Linings with Rivets. 2"Wx15 - 1/2" L, (Item #: 125742) $61.00

Brake Repair Kit - For tractor models 9N, 2N from 1939-1947. (Item #: 115181, Ref: 9N2065) $40.00

No
Picture
Brake Shoe Set - For 9N, 2N. Brake Shoes. Replaces C5NN2284F. Set of 4 shoes. (Item #: 105487, Ref: 9N2219A) $90.00

Brake Shoe Set, Set of 4 - Set includes 4 Brake Shoes with bonded lining. For 9N and 2N. (Item #: 105487, Ref: 9N2019) $90.00

Felt Brake Dust Seal - This Felt Brake Dust Seal is used on Ford 9N and 2N Tractors 1939 to 1947. It replaces original part number 9N2217. Two used per tractor. Sold individually. (Item #: 183010, Ref: 9N2217) $9.30

Nut - For Ford tractor models 2N, 9N, Replaces Ford OEM number 33806S7, 33806S8, HD58NFNUT, 5/8", 18 NF RH Thread, (Item #: 111219) $0.60

Clutch

Clutch Alignment Tool - 1-3/8 inch 10 spline, .67 inch pilot. This clutch alignment tool is for tractor models with single clutch: 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900. (Item #: 119892, Ref: 1112-5996) $10.70

Clutch Cross Shaft - This Clutch Cross Shaft is used in Ford 9N, 2N and 8N Tractors. Replaces original part number B7510A2 (Item #: 183687, Ref: B7510A2) $25.00

Clutch Disc - Clutch disc measuring 9 inches with a 1 3/8 inch hub and 10 splines. This is a 6 spring clutch. Fits tractor models 8N, 9N, 2N, NAA (4 speed), NAB, 600, 700, 800, 900 (to serial number 14257), 1800, 2130. Improved from original by added springs. Also replaces 84365150, 91A7550, NAA7550A. (Item #: 111601, Ref: 91A7550WHD) $29.10

Clutch Disc, 9in - New, 9" Organic, Spring Loaded, 1.375" spline dia. 10 spline. For tractor models 1800, 2130, 8N, 9N, 2N, NAA, NAB, 600, 700, 900. (Item #: 111601, Ref: 180250-F) $29.10

Clutch Fork To Cross Shaft Pin - This Clutch Fork to cross shaft pin is 5/16 inch X 1 1/2 inches. It is used on Ford Tractors built between 1939 and 1964. Replaces 352581S8, 352581-S8, 352581S. (Item #: 178203, Ref: 352581S8) $2.10

Clutch Kit, 9 Inch, Single Clutch - This 9 inch Clutch Kit contains 10 spline spring drive disc part number NAA7550A, 9 inch single pressure plate part number 8N7563, pilot bearing part number C5NN7600A, release bearing part number C0NN7580A and alignment tool. This clutch kit is for tractor models 1800, 1801, 2000 (4 cylinder 1962-1964), 2031, 2110TR, 2120, 2130, 2131, 4000 (4 cylinder 1962-1964), 4031, 4110TR, 4120, 4121, 4130, 4131, 4140, 501, 600, 601, 700, 701, 800, 801, 900, 901, 2N, 8N, 9N, NAA, NAB. (Item #: 121833, Ref: 8N7563K) $115.00

Clutch Pedal Bushing - 1 inch inside diameter. For 9N, 2N 1939-1947. Clutch Pedal Bushing. Replaces original part number 9N7508. (Item #: 178024, Ref: 9N7508) $7.90

No
Picture
Clutch Release Bearing Hub, Used - For Ford tractor models NAA, 2N, 8N, 9N, 2000 (1/1962-12/1964 with 4 cyl engine), 2031, 2111, 2120 (1/1963-12/1964 with 4 cyl engine), 2131, 4000 (1/1962-12/1964 with 4 cyl engine), 4031, 4120, 4121, 4130 (3/1963-12/1964), 4131, Compatible with Ford Construction and industrial models 1801, 1821, 1841, 2030, Replaces Ford OEM number 9N7561, For a new version of this item use Item #: 163512, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 436337) $23.01

Clutch Release Fork, Used - For Ford tractor models NAA, 2N, 8N, 9N, 501, 541, 600, 601, 620, 621, 630, 631, 640, 641, 2000, 2031, 2111, 2120, 2130, 2131, 4000, 4030, 4031, 4120, 4121, 4130, 4131, 4140, Compatible with Ford Construction and industrial models 1801, 1821, 1841, 4040, 4140, Replaces Ford OEM number 487515, For a new version of this item use Item #: 184395, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 459478) $19.01

Clutch Release Shaft Fork - This Clutch Release Shaft Fork is used on Ford Tractors 1939 - 1954. Replaces original part number 487515, 48-7515. For models 9N, 2N, 8N, NAA and Jubilee. NOTE: Due to variances in OEM. this part may require the bored holes to be honed slightly to fit. There was variation throughout production with Ford. (Item #: 184395, Ref: 487515) $31.50

Clutch Release Shaft, Used - For Ford tractor models NAA, 2N, 8N, 9N, 501, 541, 600, 601, 620, 621, 630, 640, 641, 650, 660, 700, 701, 740, 741, 800, 801, 820, 840, 841, 850, 860, 900, 950, 960, 2000, 2031, 2111, 2120, 2130, 2131, 4000, 4030, 4031, 4120, 4121, 4131, Compatible with Ford Construction and industrial models 1801, 1821, 1841, 4040, 4140, Replaces Ford OEM number B7510A2, For a new version of this item use Item #: 183687, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 459482) $13.01

Clutch Release Throw Out Bearing - Greaseable - Compatible with Ford Tractor(s) NAA, Super Dexta, 2N, 8N, 9N, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 761, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2100, 2110, 2120, 2300, 2600, 2610, 3000, 3055, 3100, 3110, 3120, 3190, 3300, 3310, 3330, 3600, 3610, 4000, 4100, 4110, 4410, 4600, 4600SU I.D.: 2.0625" O.D.: 3.562" Thickness: .812" Replaces Ford OEM nos C7NN7580A, C0NN7580A, E1ADKN7580B (Item #: 113482) $19.10

Clutch Shaft Bushing - This clutch shaft bearing has a 7/8 inch inside diameter. This clutch shaft bushing is for tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000. (3 or 4 Speed Transmission only). (Item #: 178029, Ref: 407508A) $7.90

Pilot Bearing - This Pilot Bearing measures .669 inches inside diameter, 1.575 inches outside diameter and is .472 inches wide. For tractor models 8N, 9N, 2N, NAA, NAB, Jubilee, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000, Dexta, Super Dexta, Major, Power Major, Super Major. (Item #: 107933, Ref: C5NN7600A) $3.40

Pressure Plate - This 9 inch single pressure plate, flat flywheel type is for tractor models 1800, 2130, 8N, 9N, 2N, NAA, NAB, 600, 700, 800, 900 with a single clutch. (Item #: 172898, Ref: 8N7563) $92.00

Pressure Plate Assembly, Remanufactured, 09A7563, 8N7563 - For Ford tractor models Dexta, NAA, Super Dexta, 2N, 8N, 9N, 600, 601, 620, 621, 630, 631, 640, 641, 650, 651, 660, 700, 701, 740, 741, 800, 801, 820, 821, 840, 841, 850, 851, 900, 901, 941, 950, 951, Replaces Ford OEM number 09A7563, 8N7563, Pressure Plate Size: 9", Pressure Plate Levers: 3, Pressure Plate Springs: 6, Pressure Plate Type: Single Stage, (Item #: 205807) $78.01

Release Bearing - This release bearing is for Ford Tractors with a 9 inch or 10 inch single clutch 1939 to 1964. It has an inside diameter of 2.0625 inches, an outside diameter of 3.515 inches, a width .7969 inches. It replaces 78-7580A, 787580A, 787580A8, C0NN7580A. (Item #: 107007, Ref: N1087) $18.50

Release Bearing Hub - This release bearing hub is for tractor models: 1801, 1821, 1841, 2000, 2030, 2031, 2111, 2120, 2130, 2131, 4000, 4030, 4031, 600, 601, 700, 701, 800, 801, 900, 901, 2N, 8N, 9N, NAA, Jubilee, NAB. (Item #: 163512, Ref: 9N7561) $41.00

Release Bearing Spring - This Release Bearing Spring measures .627 inch outside diameter, 4.875 inch overall length and .095 inch wide diameter. For tractor models 8N, 9N, 2N, NAA, Jubilee, 501, 541, 600, 601, 700, 701, 800, 801, 820, 900, 901, 1801, 1821, 1841, (2000, 4000 4-cylinder), 2030, 2031, 2110, 2111, 2130, 2131, 4030, 4040, 4031, 4110, 4121, 4130, 4131, 4140. Two are used per tractor. Sold and priced each. (Item #: 121564, Ref: 9N7562) $7.00

Cooling System

Fan Belt - For tractor models 8N, 9N, 2N EARLY with Front Mount Distributor. Length is 44 1/8 inches. Alternator Belt for those tractors using our 12 volt conversion kit. (Item #: 164264, Ref: 9N8620B3-SL) $6.70

Fan Belt - For tractor models 9N, 2N and early 8N with Generator and Front Mount Distributor. Not for tractors with alternator conversion. This belt is 46-1/8 inches long. (Item #: 167591, Ref: 9N8620B3) $14.10

Fan Blade - 4 Blade - For tractor models 9N, 8N, NAA, Jubilee. Has 4 mounting holes on 3.125 inch centers. Diameter is 15.75 inch. (Item #: 100768, Ref: 8N8600A) $48.00

Fan Blade, 6 Blade - For 9N, 8N, 2N, NAA, Jubilee. 6 Blade Fan for extra cooling in those hotter climates. (Item #: 155372, Ref: 9N8600D) $56.00

Fan Shroud - For 8N, 9N, 2N. Metal Fan Shroud. (Item #: 100766, Ref: 2N8146) $70.00

Fan Shroud Hardware Kit - This fan shroud hardware kit is used for mounting original Fan Shrouds on Ford Tractors, 1939-1964. The kit includes 7 screws and 7 washers. Some models listed use less than 7. (Item #: 178200, Ref: 357622-K) $5.60

No
Picture
Fan Shroud, Used - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 2N8146, For a new version of this item use Item #: 100766, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 400766) $46.01

Radiator - This is a Restoration Quality radiator for the 9N, 2N and 8N models. This radiator replicates the original with lower cast connections and domed top tank, and Copper core. Replaces 8N8005. (Item #: 107889, Ref: 8N8005-R) $227.00

Radiator - This is a Replacement High Quality Radiator. It is not exactly like original but will replace the original with no modification required (except if using a fan shroud). For 8N, 9N, 2N. Copper Core, 3 rows of tubes, weight 16 lbs. Drain cock included. 1 year warranty. DOES NOT COME WITH CAP. The Original or Replacement Fan Shroud will not fit this radiator without some modification to the fan shroud. This modification consists of trimming the inside of the bottom of the fan shroud. This is a replacement radiator for OEM part number 8N8005. (Item #: 101692, Ref: 8N8005) $170.00

Radiator Cap - Plain, Conventional Type 4 psi Pressure Cap, less ornament. For tractors 8N, 9N, 2N. (Item #: 108081, Ref: 2N8100A-LW) $10.00

Radiator Cap, Black - For 8N, 9N, 2N with pressurized system. Winged Radiator Cap. (Item #: 109985, Ref: 2N8100A) $9.00

Radiator Cap, Chrome - For tractor models 8N, 9N, 2N with pressurized system. Winged Radiator Cap, Chrome. (Item #: 179799, Ref: S.61615) $14.80

Radiator Hood Pad - These Radiator Hood Pads fit models 8N, 9N, 2N. One pad is used at the top of the radiator. (Item #: 109512, Ref: 2N8032) $5.50

Radiator Hose And Thermostat Kit - 160 Degree - For Ford tractor models 2N, 8N (s/n 263843-earlier), 9N, Replaces Ford OEM number 2N8260, B2NN8575A, 312588, Includes: Upper and Lower Radiator Hose and Thermostat, 160° F, (Item #: 159804) $40.00

Radiator Hose Clamp - This radiator hose clamp is an EXACT reproduction of the ORIGINAL hose clamp. This radiator hose clamp is for tractor models 8N, 9N, 2N (1939 to 1954), NAA, Jubilee (2 per tractor, 1953 to 1954). For 1 3/4 inch to 2 inch outside diameter hoses. Also works on other Ford 4 Cylinder tractors through 1964. Priced each. Replaces 608287. PLEASE NOTE: Original hoses are usually thicker than current hoses available for many antique tractors. Measure your current outside diameter to ensure fit. You can add electrical tape to the ends to have these original style clamps effectively tighten on newer (thinner) hoses. (Item #: 178164, Ref: 608287) $3.80

Radiator Hose, Lower - This lower radiator hose goes from the water pump to lower radiator. Hose is 1 1/2 inch inside diameter. For tractor models 2000, 4000, NAA, 2N, EARLY 8N, 9N, 501, 600, 601, 700, 701, 800, 801, 900, 901. (Item #: 108082, Ref: 312588) $5.20

Radiator Hose, Upper - Hose, Cylinder Head to Radiator Upper. For tractors 9N, 2N and 8N. (Item #: 109956, Ref: 2N8260) $5.80

Radiator Mounting Bolt Kit - These Radiator Mounting Bolts are used on aftermarket radiators to mount the radiator to the front support. Kit includes 2 Carriage Bolts, 2 Nuts, 2 Lock Washers and 2 Washers. For tractor models: 2000 4 cylinder, 2N, 4000 4 cylinder, 8N, 9N, Jubilee, NAA, NAB, 600, 601, 800, 801, 2030, 2031, 2120, 2130, 2131, 4030, 4031, 4120, 4121, 4130, 4131 4 cylinder. Replaces Nut 34670, 34090S, Flat Washer 44732, Lock Washer 34808, Carriage Bolt 351655S8. (Item #: 182536, Ref: 351641S8) $8.30

Radiator Mounting Pads, Pack of 2 - This pack of 2 radiator mounting pads is for tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 3000, 4000, 5000, 7000, 2600, 3600, 4600, 5600, 6600, 7600, 6700, 7700, 2310, 2610, 3610, 3910, 4610, 5610, 6610, 7610, 6710, 7710, 7810, 8010. Replaces B9NN8125A, 81811605 and C5NN8125A. Two are used per tractor on the bottom of the radiator. (Item #: 109978, Ref: 180705M1) $2.40

Thermostat - This thermostat is 160 degree lo-temperature. For tractors models 8N, 9N, 2N. Fits in upper radiator hose with the pointed end towards the front of the tractor. Thermostat is 2.250 inches long. Replaces 181634M1, B2NN8575A, 9N8575A3 (Item #: 109513, Ref: B2NN8575A) $20.20

Water Pump - This water pump is for tractor models 2N, 9N, and 8N. 1939-1952. Replaces 8N8501A, CDPN8501A, CDPN8501AA, 87791055. (Item #: 100554, Ref: CDPN8501A) $38.00

Water Pump Cover plate Gasket - Tractors: 8N, 9N, 2N (Item #: 111834, Ref: 9N8507) $1.00

Water Pump Mounting Gasket - Gasket, Pump rear to Cylinder Block. Tractors: 8N, 9N, 2N. (Item #: 111448, Ref: 9N8513) $1.70

Water Pump Replacement Kit - Kit includes CDPN8501A water pump with gasket, B2NN8575A Thermostat, 2N8260 upper hose, 312588 lower hose, 9N8620B3 fan belt (for generators), 4 hose clamps, and clamp key. Note: if your tractor has been converted to an alternator, this kit does not contain the correct belt. The correct belt for alternator conversions is part number 9N8620B3-SL, sold separately. It is used on Ford 9N, 2N and (8N up to serial number 263842, with front mount distributor). YTO 119842 (Item #: 186007, Ref: 119842) $111.00

Water Pump Sealant - RTV Blue 3.35 oz. tube. (Item #: 178141, Ref: PRM77BR) $10.60

Decals and Emblems

Data Plate - Patent Data Plate, with drive screws to install. Restoration Quality. For tractors: 9N, 2N, {1939-1947}. (Item #: 178179, Ref: 9N14001) $10.60

Decal, Fender Set - For 8N, 9N, 2N. Each decal is approximately 8-3/4 inches wide by 3-1/4 inches tall. Fender Decals (2) Red Ford Script. (Item #: 182497, Ref: R2006) $16.50

Decal Set - Combination Vinyl Decal Set For tractor models 8N, 9N and 2N (1939-1952). Set of 10 self adhesive decals. Contains decals for air cleaner, oil filter, position control, PTO warning, hood sides (Red Ford Name 2-1/4 inches x 5-1/4 inches), fenders (Red Ford name 3-1/4 inches x 9 inches) and tachometer. (Item #: 182463, Ref: R2008) $39.00

Decal Set - For 8N, 9N, 2N, all 1939-1947. Decal set for the Air Cleaner, Oil Filter Position (2) and PTO Warning. (Item #: 101986, Ref: FO1) $11.60

Decals, Hood Set - For tractor models 8N, 9N, 2N, 1947-1952. Hood Decals (2) Red Ford Script. (Item #: 182508, Ref: R2005) $11.80

Ford Instructions Decal Set - For Ford tractor models 2N, 8N, 9N, Instructions and decals for air cleaner, oil filter (2), position control, PTO warning, Mylar, (Item #: 101986) $11.60

Grill Emblem - This Ferguson System Grill Emblem was used between 1939 and 1947. Replaces original part number 9N8215 (Item #: 184948, Ref: 9N8215) $29.10

Hood Emblem - Two piece emblem set says "Ford" and "Ferguson System", includes 355870-S speed nuts. Cast aluminum, dull finish with black outline and lettering. For tractors 9N and 2N. (Item #: 108195, Ref: 2N16600) $26.20

Hood Emblem - This is a New Ford Hood Emblem Blue with Chrome. Ford 1939 - 1942. Replaces Original Part Number 9N16600S (Item #: 178093, Ref: 9N16600S) $29.10

Drive Train

Axle Bearing Assembly - For tractor models: 8N, 9N, 2N, NAA, Jubilee. This includes rear axle bearing (2N4221) and cup (9N4222). (Item #: 179813, Ref: S.18516) $47.00

Axle Collar - This axle collar measures 2 3/4 inches outside diameter, 2 inches inside diameter and 11/16 inches thick. For tractor models 9N, 2N. (Item #: 112070, Ref: 9N4132) $11.20

Axle Rear Bearing Race - This Tapered Bearing Cup is for models 4120, 600, 800, 8N, 9N, 2N, Jubilee, NAA. (Item #: 109579, Ref: 9N4222) $11.20

Countershaft - For 9N, 2N, both with 3 speed transmission. Countershaft. (0621R) (Item #: 126177, Ref: 9N7111) $108.98

Differential Bearing and Cup - This Differential Bearing and Cup is used on Ford 2000, 2120, 2N, 3000, 4110, 600, 601, 8N, 9N, Dexta, Jubilee, NAA and other. Replaces original part numbers B4222, BB4222, BB4221B, 510884, 510892, 81709463, 83402421. (Item #: 179801, Ref: 195159M1) $28.90

Differential Gasket Kit, 6 Pieces - Fits 8N, 9N, 2N. 6 Piece Set. Includes: (1) 9N502, (1) 9N611, (2) 2N4035, (1) C5NN747A, (1) 9N4662, (1) 181217M3 (Item #: 178111, Ref: DGK928) $16.80

Differential Pinion Bearing Cone - For tractor models 2000 1965>, 2N 1939-1952, 3000 1965>, 4110 1965>, 600 with 4 speed transmission serial number <54165 - 1958, 5 speed transmission serial number <196155 - 1959, 601 with 4 speed transmission serial number 54166> -1958-1962, 5 speed transmission serial number 106116> - 1960-1964, 8N 1939-1952, 9N 1939-1952, Dexta 1957-1964, NAA 1953-1954. Replaces BB4221B, 510884. (Item #: 109606, Ref: BB4221B) $31.60

Differential Pinion Bearing Cup - Bearing Cup, Differential Bearing. For 2000, 2120, 2N, 3000, 4110, 600, 601, 8N, 9N, Dexta, Jubilee, NAA Replaces BB4222, BB4222B, 510892. (Item #: 116984, Ref: BB4222) $18.70

Differential Pinion Bearing Cup, Front - For tractor models 2N 1939-1952, 8N 1939-1952, 9N 1939-1952, Dexta 1957-4/1962, NAA, Jubilee 1953-1954. (Item #: 172732, Ref: BB4616B) $60.81

Differential Pinion Cone, Front - Bearing, Tapered Cone. For tractor models 2N 1939-1952, 8N 1939-1952, 9N 1939-1952, Dexta 1957-4/1962, NAA, Jubilee 1953-1954. (Item #: 172497, Ref: BB4621B) $77.00

Differential Pinion Pilot Bearing - This differential pinion pilot bearing is for tractor models 2N (1939 to 1952), 4120 with 4 speed transmission serial number 54166> - 1959>, 5 speed transmission serial number 106115> - 1959>, 800 with 4 speed transmission serial number <54166 - 1958, 5 speed transmission serial number <106115 - 1960, 801 with 4 speed transmission serial number 54166> - 1959>, 5 speed transmission serial number 106115> - 1959>, 8N (1939 to 1952), 9N (1939 to 1952). (Item #: 172931, Ref: BB4625B) $97.00

Gasket, Drain Plug - Hydraulic and Transmission Drain plug Gasket. 2 inch inside diameter. Fits Ford Tractors, 1939 to 1964. Replaces: 81804570, 8N7011. (Item #: 112227, Ref: 8N7011) $1.70

Gasket, Main Drive Gear Bearing Retainer - For tractor models 8N, 9N, 2N, NAA, Jubilee, NAB. (Item #: 172746, Ref: 9N7086) $1.10

Gear Shift Boot - Transmission Gear Shift Lever Boot. For tractors: 8N, 9N, 2N, NAA. Bottom hole is 1-1/2 inches in diameter. (Item #: 184029, Ref: 8N7277) $5.80

Gear Shift Boot - This gear shift boot has a bottom hole that is 7/8 inch diameter. For 9N, 2N, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000 (ALL 1939 TO 1964 WITH 4 SPEED). Gearshift Boot - Restoration Quality. Can be used to replace 9N7277. (Item #: 108079, Ref: C5NN7277C) $3.30

Gear Shift Lever Spring - This gear shift lever spring fits tractors with a 3 or 4 speed transmission, or 4 speed Torque Converter Transmission, It is 2.210 inches tall, 1.768 inch tapers to 1.003 inch outside diameter, 0.140 inch wide diameter. It is for tractor models 8N, 9N, 2N. (Item #: 155070, Ref: 9N7227B) $11.00

Gear Shift Pin - This gear shift pin fits tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000 (>1965 ) with 3 and 4 speed transmission). (Item #: 169927, Ref: 9N7221B) $5.70

Input Drive Shaft - This Input Drive Shaft has 10 Splines, 20 Helical Teeth. It is used on 3 and 4 speed transmissions on Ford: 8N, 9N, 2N, NAA, 500, 600, 700, 800, 900. It replaces original part number 2N7017A. (Item #: 179301, Ref: 2N7017A) $255.00

Oil Seal, Main Drive Gear - This main drive oil seal is for 3 and 4 speed transmissions on tractor models: 8N, 9N, 2N, 600, 700, 800, 900, NAA, NAB, Jubilee. Measures 2 inches outside diameter, 1.34 inches inside diameter and .332 inches wide. Replaces part number: 8N7052A, 8N7052A2, C0NN7C248A. (Item #: 109957, Ref: 8N7052A) $8.00

Rear axle housing gasket - This "Trumpet Gasket" is the center housing to rear axle housing. Tractors: 8N, 9N, 2N. (Item #: 109576, Ref: 2N4035) $1.40

Rear Axle Housing Gasket, Outer - Fits Ford 8N, 9N, 2N, NAA and Jubilee. Replaces 9N4130, 8N4229E and 8N4229. Used for seal between bearing retainer and axle housing or backing plate. More than one may be required when used as 8N4229 shim. Thickness 0.016 inches. (Item #: 153608, Ref: 9N4130) $1.00

Rear Axle Outer Seal - Oil Seal, outer, rear axle shaft. Inside diameter 2 3/8 inches. For tractors 9N, 2N, (1939-1947). 2.437 inch inside diameter, 3.485 inch outside diameter. For 9N, 2N. (Item #: 126593, Ref: D6NN4251A) $6.20

Rear Axle Sure-Seals - Fits 9N, 2N. 1 pair. No need to split collar and replace old outer axle seal. Sure-Seal fits over top of sweat collar. (Item #: 111256, Ref: SS92) $18.30

Sherman Transmission External Lever - Step Up/Step Down lever. For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881 with Sherman trans. (Item #: 182895, Ref: 10A909) $117.00

Sherman Transmission External Lever - Step Up/Step Down Lever. For Tractors with Sherman transmission. Replaces 10A909, 9N7210. For models 9N, 2N, 8N, NAA, Jubilee, 500, 501, 600, 601, 700, 701, 800, 801, 900 and 901. (Item #: 182895, Ref: 9N7210) $117.00

Shifter Cable - This is a Sherman Transmission Shift Cable with Knob. It is 3/8 inches, 24 NF inner ends and 1/2 inch, 20 NF outer end thread. 31-1/2 inches overall length. It is used on 9N, 2N and 8N tractors with Sherman high/low transmissions. (Item #: 184666, Ref: SHERMAN-1) $100.00

Shim for Bearing Retainer - This is a Steel Shim, .020 thick. It has 12 holes. Will work in 6 hole applications. Fits Ford 8N, 9N, 2N, NAA and Jubilee, 8N4229F and 8N4229. More than one may be required when used as 8N4229F shim. Thickness 0.020 inches. Price is for each. (Item #: 178176, Ref: 183261M1) $3.60

Side Cover Gasket - This Side Cover Gasket fits the following tractor models as a side cover gasket and a PTO shift cover gasket: 2000, 4000, 2N, 8N, 9N, 600, 601, 700, 701, 800, 801, 900, 901, Jubilee and NAA. Replaces part number 9N4131. (Item #: 112236, Ref: 9N4131) $1.00

Transmission Bearing - Main Pilot Shaft Bearing Cone for 3 and 4 speed transmissions. For tractor models 1801, 1821, 1841, 2000, 2030, 2031, 2100, 2110, 2111, 2120, 2130, 2131, 2150, 2300, 2310, 2N, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3500, 3550, 4000, 4030, 4031, 4040, 4110, 4120, 4121, 4130, 4131, 4140, 600, 601, 620, 621, 630, 631, 640, 641, 700, 701, 740, 741, 800, 801, 840, 841, 8N, 9N, NAA, Jubilee, NAB. (Item #: 118284, Ref: 9N7120) $97.00

Transmission Bearing Cone - Main Drive Shaft and Countershaft Bearing Cone for 3 and 4 speed transmissions. For tractor models 2000, 3000, 4000, 5000, 2N, 8N, 9N, 600, 700, 800, 900, NAA, NAB. (Item #: 110536, Ref: 9N7066) $12.00

Transmission Case to Center Housing Gasket - For tractor models 9N, 8N, 2N. (Item #: 112152, Ref: 9N4662) $3.20

Transmission Drain Plug - Has 2.3 inch outside diameter. For tractors: 8N, 9N, 2N, NAA, {1939-1954}. Also filler plug for tractor: NAA {1953-1954}. Gasket available, order part number 8N7011. Replace 9N7010, 8N7010. For a magnetic version of this plug, order 8N7010 (Item #: 115163, Ref: 9N7010) $6.30

Transmission Drain Plug, Magnetic - Used on Ford tractors 1939-1964, this part has the same measurements as part number 9N7010 (2 inch-12 UN Threads) but is also magnetic to collect small metal particulate. Includes gasket. (Item #: 184037, Ref: 8N7010) $18.40

Transmission Rebuild Kit - For tractor models 9N, 2N and 8N with 3 and 4 speed transmissions (1939-1952). Will also work for Jubilee except for the transmission to rear end gasket. This transmission bearing and seal kit contains seals, bearings and gaskets required for transmission rebuild. Contains (2) 9N7086, (1) 9N4662, (1) D5NN7223A, (1) 9N7223B, (1) 8N7052A, (1) 15385-TIM, (4) 25877, (4) 25820-TIM. Replaces: 9N7066, 86516471, 9N7086, 9N7086A, 9N7086GV, 9N7120, 9N7120GV, 81804773, 8N7052A, 8N7052A2, C0NN7052A, 83945495, 9N7067, 9N7067GV, 517512, 241336, 605188, 9605470, 9N4662, 9N4662GV, 9N7223, 9N7223B, 8N7223, D5NN7223A, E6NN7223BA, 83958318, 81817212. (Item #: 183888, Ref: TSBK3952) $199.00

Electrical System

12 Volt Conversion Kit, Front Mount Distributor - 8N, 9N, 2N. Updates older 6-volt tractors to 12-volt charging system. For 9N, 2N, (early 8N 1948-1951) with Front Mount Distributor (distributor is right behind radiator), to serial number 263843. Kit includes rebuilt unicharge alternator with pulley and self exciting regulator, resistor, 12 Volt coil, wiring harness, top alternator bracket, alternator base bracket, alternator adjusting arm, and belt. Note, using the brackets in this kit may require trimming of the conduit your spark plug wires run through. Many tractors no longer have this conduit. Will not work if you have a magneto. (Item #: 103139, Ref: 8NE10300ALT-C) $150.00

Alternator, 12 Volt - 12 Volt, 63 Amp Alternator replacement for systems that have been previously modified to 12 volts. Does not include hardware. Simple 1-wire "self exciting" alternator has internal voltage regulator (easy to wire). 10SI Type Configuration. (Item #: 111377, Ref: 8NE10305SE) $94.00

Alternator Adjustable Arm - Alternator Adjusting Arm. For 8N, 9N, 2N - EARLY with Front Mount Distributor. (Item #: 164212, Ref: 8NE10304) $13.50

Alternator Base Bracket - Alternator Base Bracket. For 8N, 9N, 2N - EARLY with Front Mount Distributor. (Item #: 164211, Ref: 8NE10303) $9.98

Alternator - Delco Style (7127), Remanufactured, Delco Remy, 10459509 - For Ford tractor models NAA, 2N, 8N, 9N, Compatible with Massey Ferguson tractor models TO20 (less tachometer), Replaces Delco Remy manufacturer number 10459509, Replaces manufacturer number 13-40113, 13-4011SW, 240-204-3, 7127-3SE, 7127-SEC, 240-204C, 90-01-3125, 7127-1W, N7127-1W, RA00103, For Universal Applications, 1-Wire Hookup, Delco Style, Voltage: 12, Amperage: 63 (Self Exciting), Rotation: Clockwise, Regulator: Internal, For a New version of this sku use Item #: 111377, (Item #: 204209) $193.01

Alternator Pulley - For 8N, 9N, 2N, NAA, 600, 700, 800, 900. All using 12 Volt conversion kits with a Delco single wire alternator. Pulley, single groove 5/8 inches wide. The diameter varies from our different suppliers. This measures about 2 5/8 inches outside diameter, give or take about a 1/4 inch. This should be fine and within the adjustability of the Alternator Adjusting Arm. Replaces 98NAA5825. (Item #: 172594, Ref: AFD5035) $21.50

Alternator Top Bracket - Alternator Top Mounting Bracket. For 8N, 9N, 2N - EARLY with Front Mount Distributor. (Item #: 164213, Ref: 8NE10302) $14.50

Battery Cable - 2 gauge. For tractor models 9N, 2N (from 1940). This cable is a battery to starter and is 21 inches long. (Item #: 172373, Ref: 9N14300C) $19.80

Battery Cable - For 8N, 9N, 2N. Ground Strap. 7 inches. (Item #: 115790, Ref: D1NN14301H) $12.50

Battery Cable - This Battery Cable is 14 inches long and is 2 Gauge. For models (600, 700, 800, 900, 1958-1964), (2000, 4000 all before 1964). Ground Cable. (Item #: 172920, Ref: D1NN14301G) $20.70

Battery Hold Down Set - For Ford tractor model 9N (Through 1942), Replaces Ford OEM number 9N10728C, 9N10748, Sold as Pair, Comes primered (color may vary). Prior to painting check fitment, For right hand side use Item #: 191179, (Item #: 126468) $54.00

Bearing, Generator Front - BEARING, BALL Bearing, Generator, Front End. For 3 Brush Generator. For early 8N, 9N, 2N. Measures .59 inches inside diameter and 1 3/8 outside diameter. Verify Measurements. (Item #: 108447, Ref: E27N10094B) $1.80

Cable, Starter to Switch - Switch to starter cable, 16 inches long. For 9N, 2N, 601, 701, 801, 901, 600, 700, 800, 900, NAA, 2000, 2031, 2111, 2120, 2131, 4000, 4030, 4031, 4040, 4120, 4130, 4140, 501, 541. Replaces FAA14431B. (Item #: 115783, Ref: 9N14431B) $10.00

Cigar Lighter Assembly - Complete with mounting bracket. Original accessory cigar element well, knob and wire. Ready to mount. For all models 1939-1954 (Item #: 183039, Ref: 8N9004601A) $48.20

Coil, 12-Volt - For 8N, 9N, 2N (serial number up to 263843. Front Mount Distributor 12 Volts. Order 9N12104 gasket set separately if mounting gasket is needed. Replaces 9N12024-12V. (Item #: 105530, Ref: 12VOLTCOIL) $26.00

Coil - Six Volt - For tractor models 8N (1939-1950), 9N, 2N with Front Mount Distributor. Order 9N12104 gasket set separately if mounting gasket is needed. (Item #: 105529, Ref: 9N12024) $21.80

Coil - Six Volt with Script - The is an officially licensed Ford 6 Volt Coil, with raised Ford script. Replaces 9N12024. Order 9N12104 gasket set separately if mounting gasket is needed. YTO 9N12024S (Item #: 182900, Ref: 9N12024S) $52.00

Complete Tune-Up and Maintenance Kit - For Ford tractor models 2N, 8N, 9N (all with front mount distributors), Includes points, condenser, plugs, distributor cap and rotor, universal spark plug wire set, .015 and .025 feeler gauges, oil cap, oil filter with o-ring and sediment bowl assembly, For front mount distributor models, (Item #: 116751) $73.00

Condenser - Fits 8N, 9N, 2N with Front Mount Distributor. (Item #: 111199, Ref: A0NN12300A) $6.60

Distributor Assembly, Complete - For 9N, 2N, (8N all front mount serial number up to 263843). Includes: points, condenser and distributor cap. Does not include coil or mounting gaskets. (Item #: 105325, Ref: 9N12100) $70.00

Distributor Breaker Plate - Breaker Assembly, complete with points. For 8N, 9N, 2N. For Front Mount Distributor. Please note that suppliers have been replacing distributors, distributor base assemblies and breaker plates with after market parts for some time and the mounting screw that comes into the side of the distributor is slightly higher. This may require some modification if your mounting screw does not line-up. (Item #: 116682, Ref: 9N12150) $30.60

Distributor Breaker Plate Retainer Clip - For tractor models 8N, 9N, 2N (Front Mounted Distributor). (Item #: 119700, Ref: 91A12146) $4.50

Distributor Bushing, FRONT - Front Distributor Bushing is for FRONT MOUNT DISTRIBUTOR only. For 9N, 2N, early 8N. (Item #: 110784, Ref: 9N12120) $4.10

Distributor Bushing, REAR - Bushing, (rear), for Front Mount Distributor, 8N, 9N, 2N. (Item #: 108788, Ref: 18-12132) $5.40

Distributor, Cam and Weights Assembly - Distributor Shaft with Cam and Weights attached for 9N12100 Front Mounted Distributor. For use on Ford tractor models 9N, 2N, and 8N before serial number 263843, 1939 to 1950. (Item #: 178579, Ref: 9N12187) $43.70

Distributor Cap - For tractor models 8N, 9N, 2N to serial number 263843 all with Front Mount Distributor. Distributor Cap. (Item #: 105526, Ref: 9N12106C) $13.20

No
Picture
Distributor Cap Gasket - For Ford tractor models 2N, 8N (s/n 263844-earlier), 9N, Replaces Ford OEM number 91A12114, For front mount distributors, (Item #: 111623) $3.10

Distributor Cap Spring Clip Set - For tractor models 8N, 9N, 2N (Early). Replaces 9N12144. (Item #: 168684, Ref: 9N12144) $7.90

Distributor Cap Terminal Kit - Distributor Cap Terminal kit for 8N, 9N, 2N with Front Mount Distributor Electronic Ignition Conversion Kit. (Item #: 182553, Ref: 1247XTTERM) $26.80

Distributor Cap with Pertronix Coil Modification - Pertronix Distributor Cap for 8N, 9N, 2N with Front Mount Distributor THAT HAS BEEN CONVERTED TO AUTOMOTIVE STYLE KIT WITH A PERTRONIX 1247XT KIT. (Item #: 182562, Ref: 1247XTCAP) $45.30

Distributor Clamp Rivet - This Distributor Clamp Rivet is used to secure part number 7RA12144 to the distributor. Used on Ford tractor models: 8N, 9N, 2N, NAA, Jubilee, 600, 601, 700, 701, 501, 800, 801, 900, 901, 1801, 2000 and 4000, 1950-1964. It replaces B12145, B-12145. (Item #: 182949, Ref: B12145) $1.30

Distributor Coil Bail - For tractor models 8N, 9N, 2N with Front Mount Distributor. (Item #: 112186, Ref: 9N12137) $4.40

Distributor Coil Gasket - For Ford tractor models 2N, 8N (s/n 263844-earlier), 9N (all w/ front mount distributor), Replaces Ford OEM number 9N12140A, (Item #: 107071) $0.80

Distributor Drive Gear - For tractor models 8N, 9N, 2N. Gear for Distributor Drive On Camshaft (Item #: 163509, Ref: 7RA6255) $22.10

Distributor Gasket Kit - For tractor models 8N, 9N, 2N prior to serial number 263844. Kit contains distributor breaker cover gasket, distributor base gasket, distributor coil base gasket, cap gasket. Replaces: 9N12104, 91A12114, 9N12140A, 9N12143, 9N12276B (Item #: 111160, Ref: 9N12104) $3.60

Distributor Point Set - Point set, Blue Streak premium quality. For tractor models 8N, 9N, 2N (Early). (Item #: 178145, Ref: A0NN12107ABS) $27.70

Distributor, Remanufactured, 9N12100 - For Ford tractor models 2N, 8N (s/n 263844-earlier with front mount distributor), 9N, Replaces Ford OEM number 9N12100, Includes new distributor cap, points, condenser, and all other parts needed for a thorough rebuilt unit, For New Distributor use Item #: 105526, (Item #: 203508) $265.01

Distributor Rotor, Front Mount Distributor - Fits 8N, 9N, 2N with Front Mount Distributor. (Item #: 111103, Ref: B2NN12200A) $5.30

Electronic Ignition Conversion Kit -12V Negative Ground - Complete Electronic Ignition Conversion Kit by Pertronix to convert your tractor to an electronic automotive type coil system.. For 8N, 9N, 2N with FRONT MOUNT Distributor only. For tractors with 12-volt negative ground only. This electronic module replaces your points and condenser, also includes 40, 000 volt coil, coil clamp, coil wire and distributor cap. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 12-volt negative ground only. (Item #: 108154, Ref: 1247XT) $310.00

Electronic Ignition Conversion Kit, 12 volt negative ground - Electronic Ignition Conversion Kit - For 8N, 9N, 2N with FRONT MOUNT Distributor only. For tractors with 12-volt negative ground only. This electronic module replaces your points and condenser. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 12-volt negative ground only. (Item #: 105081, Ref: 1247) $160.00

Electronic Ignition Conversion Kit - 6V Positive Ground - Electronic Ignition Conversion Kit. For 8N, 9N, 2N with FRONT Mount Distributor only. For tractors with 6-volt POSITIVE ground only. This electronic module replaces your points and condenser. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. (Item #: 105082, Ref: 1247P6) $200.00

Electronic Ignition Conversion Kit - 6V Positive Ground - Complete Electronic Ignition Conversion Kit by Pertronix to convert your tractor to an electronic automotive type coil system. For 8N, 9N, 2N with FRONT MOUNT Distributor only. For tractors with 6-volt positive ground only. This electronic module replaces your points and condenser, also includes 40, 000 volt coil, coil clamp, coil wire and distributor cap. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 6-volt positive ground only. (Item #: 172506, Ref: 1247XTP6) $425.00

Electronic Ignition Replacement Module - This is a replacement module for the 1247XT electronic ignition kit. Does not have the magnetic sleeve for the rotor shaft. For front mount distributor. (Item #: 182570, Ref: 1247XT0) $106.00

Generator, 6 Volt - New Generator with Pulley. For 8N, 9N, 2N. Single terminal, 6 Volt, 2 brushes. (Item #: 107888, Ref: 8N10000) $146.00

Generator Brush Set - This set is for original 3 brush Generators, used, 1939-1948. Replaces 40-10069, 40-10043 (Item #: 183025, Ref: 40-10069) $4.10

Generator Cut Out Assembly - Cut Out Assembly. For 9N, 2N. (Item #: 105534, Ref: B0NN10505A) $27.50

No
Picture
Ignitor - 4 Cylinder, 12V - For Ford tractor models NAA, 2N, 8N, 9N, Replaces Ford OEM number 8301082, Models with distributor on the front of the engine, Volts: 12, Ground: negative, (Item #: 190709) $103.31

Key Switch - For all Fords 1939 through 1964 except Dexta and Fordson Major with 3/4 inch hole. Keyed Ignition Switch comes with 2 Keys. (Item #: 105687, Ref: 8N3679C) $7.50

Point Set - For Ford tractor models 2N, 8N (s/n 263844-earlier), 9N, Replaces Ford OEM number A0NN12107A, 21A151, 9N12107, Ventilated style - for models with front mount distributors, (Item #: 111197) $10.10

Pulley, Generator - Pulley, Generator (threaded). For 8N, 9N, 2N. (Item #: 111776, Ref: 9N10130B) $27.50

Resistor - For 8N, 9N, 2N, and 4 cylinder engines on 600 - 4000 tractors 1955-1964. Used in our 12 volt conversion kits. This resistor tests at .6 ohms under load through a distributor. (Item #: 105710, Ref: 8NE10306) $3.70

Resistor - For Ford tractor models 2N, 8N (s/n 263843-earlier), 9N, Replaces Ford OEM number 9N12250, Resistor only (no mounting block), (Item #: 110783) $8.40

Resistor Assembly, Ignition Coil - For tractor models 9N, 2N. Resistor measures .5 ohms. (Item #: 111902, Ref: A8NN12250B) $18.50

Resistor Assembly, Ignition Coil OE - This resistor is built exactly like the original. It has .5 ohms of resistance. Originally used on Ford 9N and 2N Tractors, 1939 -1947. Replaces A8NN12250B (Item #: 183748, Ref: A8NN12250BOE) $43.00

Spark Plug - For 8N, 9N, 2N, NAA, NAB, Jubilee, and 134 and 172 gas engines used on: 501, 600, 601, 700, 701, 800, 801, 900, 901, (2000, 4000 ALL before 1965). SPARK PLUG. PRICE IS FOR 1. If you order one, you will receive one. If you need 3 or 4, you need to order 3 or 4. Replaces Autolite AL437, AL82, Bosch WR9FC and Champion H14Y and H18Y. (Item #: 130072, Ref: AL437) $3.10

Spark Plug Wire Bracket - For tractor models 8N, 9N, 2N, (1939 to 1950). (Item #: 178132, Ref: 9N14564) $7.40

Spark Plug Wire Set - For Ford tractor models 2N, 9N, Replaces Ford OEM number 9N12283, 9N12286, Copper Core, (Item #: 155162) $20.60

Starter, 12 Volt, With Drive - New Starter for 8N, 9N, 2N. 12 Volt. Complete starter includes starter drive. (Item #: 156607, Ref: 8N1100R) $115.00

Starter Drive - New improved design Starter Drive, for 8N, 9N, 2N (1939 to 1952). (Item #: 110660, Ref: 52-11350C) $26.10

No
Picture
Starter - Ford Style DD - For Ford tractor model 9N, Replaces Ford OEM number 9N11002, Ford Early Inertia Direct Drive, Volts: 6V, Rotation: CW, Teeth: 9, (Item #: 167404) $691.00

Starter, Gear Reduction - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 8N11001, 8N1101R, 8N11002, 9N11001, 9N11002, 10461663, (Item #: 167399) $215.00

Starter Post Kit - This kit replaces the wire post on Ford starters, 1939 to 1964. Replaces C7NF11102A, 1811107B, 86512984, 6810044. (Item #: 183576, Ref: A9AZ11102B) $8.80

Starter Repair Kit - For 8N, 9N, 2N. Starter Repair Kit contains all parts necessary for repair of starter part number 8N11001. (Item #: 178044, Ref: SRK401) $38.00

Starter Switch - For 9N serial number <12499 1939 to 1940. Starter Switch (push type). Replaces: 1996487 Delco, 405C Delco. (Not the same as Triangular 9N11450B 1940 to 1947) (TIS DR405C). (Item #: 105684, Ref: 9N11450A) $9.90

Starter Switch, Restoration Quality - Fits 9N, 2N with Safety Start. 2-3/4 inches center to center. (Item #: 105686, Ref: 9N11450B) $14.50

Starter, With Drive, 6 Volt - Starter, with drive. For 8N, 9N, 2N. (Item #: 113040, Ref: 8N11001) $119.00

Tune-up Kit - This Tune-up Kit is for tractor models 9N, 9N, 2N, and Early 8N, all with Front Mount Distributor. Tune-up Kit, Autolite. Includes: point set, condenser, rotor and (4) 437 Autolite Spark Plugs and gaskets. Verify correct spark plug size and type (Item #: 185192, Ref: 309786) $30.40

Tune-up Kit - Replace all the ingition components at once. This kit contains Condenser (A0NN12300A), points (A0NN12107A), plugs (AL437), distributor cap (9N12106C), rotor (B2NN12200A), spark plug wire set (CPN12259) and .015 and .025 feeler gauges. Used on Ford 9N, 2N and 8N up to serial number 263843. (Item #: 116745) $51.00

Tune-up Kit, Basic - This basic tune-up kit has points, condenser and rotor for Front Mount Distributor. For 9N, 2N and Early 8N. (Item #: 105523, Ref: ATK6FFR) $13.70

Tune-up Kit, Basic - This basic tune-up kit for a 4 cylinder gas contains Premium Blue Streak points (A0NN12107ABS), rotor, condenser, and gauge for Front Mount Distributor on 2N, Early 8N, and 9N. (Item #: 185624, Ref: APN12000ABSR) $37.20

Wiring Harness - Has woven fabric casing. For 2N (1943 to 1947) with single pole generator. Also for 9N with single pole generator. Ignition Wiring. Replaces 86618153, 2N14401 and 9N14401C. (Item #: 105711, Ref: 2N14401) $19.80

Wiring Harness 12 Volt - Wiring Harness for 2N, early 8N, and 9N front mount distributors tractors that has been converted to 12 Volt. Does not include light wiring. There are many different ways to wire a 12 volt conversion and this is the wiring harness provided in our 12 volt conversions set. It may be different than how your 12 volt conversion was done if not done with our kit. (Item #: 164233, Ref: 8NE10301) $24.00

No
Picture
Wiring Harness, Headlights and Rear Lights - For Ford tractor models 2N (1939 - 1949), 8N (1939 - 1949), 9N (1939 - 1949), (Item #: 185190) $97.00

Wiring Harness, Restoration Quality - Main Wiring Assembly with Ignition Light Wire. Original style braiding with soldered terminals. Made in the USA. For tractor models 9N, 2N with single terminal generator. Replaces 9N14401B. (Item #: 183785, Ref: 9N14401B) $106.00

Engine Bearings

No
Picture
Camshaft Bearing - For Ford tractor models 2N (4 Cylinder), 8N (4 Cylinder), 9N (4 Cylinder), Replaces Ford OEM number 8N4110, (Item #: 166805) $47.00

Main Bearing Set, .010 - .010 inch Main Bearing Kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N. (Item #: 106254, Ref: MBK9N633E-010) $67.00

Main Bearing Set, .020 - .020 inch Main Bearing Kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N. (Item #: 106198, Ref: MBK9N633G-020) $77.00

Main Bearing Set, .030 - .030 inch Main Bearing Kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N. (Item #: 106255, Ref: MBK9N633-030) $62.00

Main Bearing Set, .040 - This .040 inch oversize Main Bearing Set is complete for 1 engine. Contains center, front, and rear bearings. For tractor models 8N, 9N, 2N. (Item #: 106256, Ref: MBK9N633-040) $61.37

Main Bearing Set, Standard - Standard Main Bearing Kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N. (Item #: 106252, Ref: MBK9N633A-STD) $60.00

Main Bearings Set, .060 - For Ford tractor models 2N, 8N, 9N, Compatible with Ford Engine (s) 120, Bearing Size: .060" Oversize, Sold in complete set, For Standard main bearing use Item #: 106256, (Item #: 106257) $78.00

Rod Bearing, .001 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. Order 4 for a complete engine. (Item #: 184405, Ref: 9N6211B-PAIR) $14.40

Rod Bearing, .002 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Item #: 106247, Ref: 9N6211C-PAIR) $14.00

Rod Bearing, .010 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Item #: 106248, Ref: 9N6211E-PAIR) $14.60

Rod Bearing, .020 - .020 inch Connecting Rod. For 8N, 9N, 2N. (Item #: 106249, Ref: 9N6211G-PAIR) $13.50

Rod Bearing, .030 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Item #: 106199, Ref: 9N6211-030) $14.40

Rod Bearing, .040 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Item #: 106250, Ref: 9N6211-040-PAIR) $15.00

Rod Bearing, .060 - For tractor models 8N, 9N, 2N. 4 Required per engine. (Item #: 106251, Ref: CB-200P-060) $8.70

No
Picture
Rod Bearing Set - .010 inch Connecting Rod Bearing Kit. 1 kit used per engine. Contains 4 pair of 9N6211E. For 8N, 9N, 2N (Item #: 186793, Ref: CRK9N6211E-010) $47.70

Rod Bearing Set, .040 - .040 inch Connecting Rod Bearing Kit. 1 kit used per engine. Contains 4 pair of 9N6211-040. For 8N, 9N, 2N. (Item #: 184555, Ref: CRK9N6211-040) $46.29

Rod Bearing, Standard - With Journals measuring 2.095 inches. Connecting Rod Bearing. 4 required for complete engine. Sold individually. Replaces 9N6211E. For 8N, 9N, 2N. (Item #: 106246, Ref: CRK9N6211A-STD) $14.00

Engine Gaskets

Crankshaft Seal - Rope Seal, REAR. Upper and lower is the same part. For tractor models 8N, 9N, 2N. Replaces 8N6701 and 8N6702. (Item #: 164410, Ref: 8N6701) $3.20

Crankshaft Seal, Front, Pack of 2 - Rope Seal, FRONT. Upper and lower is the same part. For tractor models 8N, 9N, 2N. Price is for 2 pieces. Order quantity 1 for 1 engine. Replaces 8N6700 and 8N6707. (Item #: 128489, Ref: 8N6700) $5.20

Crankshaft Seal, Rear, Lower - use 8n6701 (Item #: 164410, Ref: 8N6702) $3.20

Crankshaft Seal, Single Piece - Replace your original 2 piece front crankshaft seal with this single piece seal. Used on Ford 9N, 2N and 8N tractors. Replaces 8N6700 and 8N6707 (Item #: 178072, Ref: 8N6700V) $4.60

No
Picture
Distributor Base Gasket - For tractor models 9N, 2N, Early 8N. MUST BE ORDERED IN MIN. QTY OF 10. ORDER WILL BE INCREASED TO A MULTIPLE OF 10. ***GASKET COMES IN 9N12104 KIT** (Item #: 110302, Ref: 9N12143) $2.20

No
Picture
Exhaust Manifold Gasket Set - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 9N9448, Set of 2, (Item #: 185201) $6.83

Full Gasket Set - Full Engine Overhaul Gasket Set with Metal Head Gasket. Comes WITHOUT front and side timing cover gaskets. For tractor models 8N, 9N, 2N. (Item #: 106258, Ref: 8N6008M) $26.60

Governor Housing Mounting Cover Gasket - For tractor models 8N, 9N, 2N. (Item #: 112157, Ref: 9N6022) $1.20

Head Gasket - Head Gasket. All soft material except for the fire rings. For tractor models 8N, 9N, 2N. (Item #: 179674, Ref: 8N6051A) $11.80

Head Gasket - Head Gasket, all metal. For 8N, 9N, 2N. (Item #: 172817, Ref: 8N6051B) $12.70

Oil Pan Gasket - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 8N6710, 8N6711, For oil pan gasket set use Item #: 106260, (Item #: 112239) $13.70

Oil Pan Gasket Set - For 8N, 9N, 2N; 7 Piece Set. Oil Pan Gasket Set with upper and lower crankshaft rope seals, left and right oil pan gaskets, and oil pan drain plug gasket. (Item #: 106260, Ref: 9N6781) $12.50

No
Picture
Timing Cover - For Ford tractor models Super Dexta, 2N, 8N, 9N, Compatible with Ford Engine (s) 120 Replaces Ford OEM number 86531515, , Compatible with New Holland tractor models T7030 (s/n Z9BG07156-Z9BG40124), T7040 (s/n Z9BG07719-Z9BG40112), T7050 (s/n Z9BG07000-Z9BG40114), T7060 (s/n Z9BG07000-Z9BG40117), Replaces New Holland OEM number 86531515, Use with Side Mount Distributor, (Item #: 166625) $117.72

Timing Gear Front Cover Gasket - For tractor models 9N, 2N, (8N prior to serial number 263844). (Item #: 112059, Ref: 9N6020A) $2.00

Timing Gear Side Cover Gasket - For tractor models 9N, 8N, 2N. Replaces original part number 8N6018 (Item #: 172754, Ref: 8N6018) $1.20

Upper Gasket Set - For tractor models 8N, 9N, 2N. Upper Gasket Set with Metal Head Gasket. Set includes: cylinder head gasket, (2) valve cover side plate gaskets, (8) valve guide seals, (2) manifold gaskets, (1) governor gasket. Replaces: 8BA6571, 9N6022, 9N9448, 7HA6521, 8N6051A. (Item #: 106259, Ref: VG8NM) $17.30

Valve Cover Gasket - For tractor models 8N, 9N, 2N. (Item #: 112151, Ref: 7HA6521) $2.70

Engine Rebuild Kits

Basic In Frame Overhaul Kit, 120 Gas - For 120 CID 4 cylinder gas 3-3/16 inch standard bore. Basic In Frame Kit contains, thick wall .090 inch sleeves, 3 ring pistons, rings, pin and retainers, valve grind gasket kit, pan gasket kit. Bearings are available, must be ordered separately. For tractor models 8N, 9N, 2N. (Item #: 189636, Ref: BIFF106A) $282.00

Basic In Frame Overhaul Kit, 120 Gas - 120 CID 4 cylinder gas 3-3/16 inch standard bore. Kit contains thin wall .040 inch sleeve, 3 ring pistons, rings, pin and retainers, valve grind gasket kit, pan gasket kit. Kit does not include bearings. For tractor models 8N, 9N, 2N. (Item #: 184670, Ref: BIFF103A) $232.00

Basic Overhaul Kit, 120 Gas, 3-ring pistons, .040 Sleeves - 120 CID 4 cylinder gas 3-3/16 inch standard bore. Basic Engine Kit contains, thin wall .040 inch sleeves, 3 ring pistons, rings, pin and retainers, pin bushings, complete gasket kit. Bearings NOT included and must be ordered separately. For tractor models 8N, 9N, 2N. (Item #: 130778, Ref: BEKF103A-LCB) $225.00

Basic Overhaul Kit, 120 Gas, 3-ring pistons, .090 Sleeves - 120 CID 4 cylinder gas 3-3/16 inch standard bore. Basic Engine Kit contains, thick wall .090 inch sleeves, 3 ring pistons, rings, pin and retainers, pin bushings, complete gasket kit. Bearings NOT included and must be ordered separately. For tractor models 8N, 9N, 2N. (Item #: 130779, Ref: BEKF106A-LCB) $260.00

Engine Overhaul Kit, 120 Gas - 120 CID 4 cylinder gas 3-3/16 inch standard bore. Engine Overhaul Kit contains, thin wall .040 inch sleeves, 4 ring pistons, rings, pin and retainers, pin bushings, complete gasket kit, intake and exhaust valves, valve springs and retainers, guides and retainers, valve keys. For 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Item #: 184667, Ref: EOK102-LCB) $480.00

Engine Overhaul Kit, 120 Gas - 120 CID 4 cylinder gas 3-3/16 inch standard bore. Engine Overhaul Kit contains, thin wall .040 inch sleeves, 3 ring pistons, rings, pin and retainers, pin bushings, complete gasket kit, intake and exhaust valves, valve springs and retainers, guides and retainers, valve keys. For tractor models 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Item #: 130806, Ref: EOK103-LCB) $450.00

Engine Overhaul Kit, 120 Gas - 120 CID 4 cylinder gas 3-3/16 inch standard bore. Engine Overhaul Kit contains, thick wall .090 inch sleeves, 3 ring pistons, rings, pin and retainers, pin bushings, complete gasket set, intake and exhaust valves, valve springs and retainers, guides and retainers, valve keys. For 8N, 9N, 2N. (Item #: 130807, Ref: EOK106-LCB) $454.00

Overhaul Kit, Comprehensive, 120 Gas - 3 RING PISTONS, .090 Inch SLEEVES, 3/4 OIL PUMP GEAR WIDTH. Complete Engine Kit. Contains, thick wall .090 inch sleeves, 3 ring pistons, rings, pins and retainers, pin bushings, complete gasket set, timing gear, intake and exhaust valves, springs, spring retainers, guides, retainers and seals, valve keys, upper and lower radiator hose, air cleaner hose, oil pump kit, fan belt, points and condenser, spark plugs, oil filter, basic carb kit. For tractor models 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Item #: 183937, Ref: 3-8H-LCB) $777.00

Overhaul Kit, Comprehensive, 120 Gas - 120 CID 4 cylinder gas 3-3/16 inch standard bore, 9/16 inch oil pump gear width. Complete Engine Kit contains, thick wall .090 inch sleeves, 3 ring pistons, rings, pins and retainers, pin bushings, complete gasket kit, timing gear, intake and exhaust valves, springs, spring retainers, guides, retainers and seals, valve keys, upper and lower radiator hose, air cleaner hose, oil pump kit, fan belt, points and condenser, spark plugs, oil filter, basic carb kit. For, 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Item #: 184576, Ref: 3-9H-LCB) $568.00

Valve Overhaul Kit - For servicing one engine when valve replacement is necessary. For 8N, 9N, 2N with solid guides, free-rotating exhaust valves. Kit contains intake valves, exhaust valves, valve springs and keys, solid type valve guides and rotating valve kit. (Item #: 108639, Ref: VOKF928NFR) $134.00

Valve Overhaul Kit - Fits 9N, 2N and 8N that use solid valve guides and have NON-rotating exhaust valves. Includes intake and exhaust valves, springs, keys, and guides. (Item #: 185386, Ref: VOKF928N) $135.00

Engine Parts

No
Picture
Bare Block, Remanufactured, FO - For Ford tractor models 2N, 8N (s/n 263844-earlier), 9N, Replaces Ford Casting number FO, Our remanufactured bare blocks have been; cleaned, inspected, align bored, and pressure checked, (Item #: 204677) $930.01

Camshaft Gear - This Press on type Camshaft Gear is used on Ford Tractors 1939-1942. THIS IS A FIBER GEAR. Replaces 48-6256-A, 486256A. (Item #: 183022, Ref: 48-6256-A) $21.60

Connecting Rod Nut - This is a Castle Style Nut for the Rod Cap on Ford tractors, 1939 to 1964. Replaces C9AZ6212B, 7HA6212, 7HA-6212. Eight used per tractor. Priced each. For models 9N, 8N, 2N, NAA, Jubilee, 501, 600, 601, 700, 701, 800, 801, 900, 901, 1801, 4000 and 2000. (Item #: 183734, Ref: 7HA-6212) $1.90

Connecting Rod Nut - For Ford tractor models NAA, 2N, 8N, 9N, 501, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 660, 661, 671, 681, 700, 701, 740, 741, 761, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 4000, Replaces Ford OEM number FC9AZ6212B, 70207132, C9AZ6212B, For OEM Quality use Item #: 183734, (Item #: 182466) $1.10

Crankshaft - New kit with bearings. For tractor models 8N, 9N, 2N with Standard Rod and Main Bearings. (Item #: 184880, Ref: 9N6303ACK) $891.00

Crankshaft - For tractor models 9N, 8N, 2N. Does not include bearings. (Item #: 100549, Ref: 9N6303A) $450.00

Crankshaft Cranking Ratchet - The ratchet nut fits into the nose of the crankshaft. The hand crank fits into the end of the ratchet to turn the engine over. Replaces original part number 2N6319A1 (Item #: 182475, Ref: 2N6319A1) $17.30

Crankshaft Pulley - This Crankshaft Pulley for models 8N, 9N, and 2N. Used with attaching a screw type hub for a front mounted hydraulic pump. Crankshaft mounting is 1.63 inch outside diameter and 1.18 inch inside diameter and has four 1/4 inch -20 threaded holes. Can be used as a regular crankshaft pulley without attaching a hub for a front mounted hydraulic pump. Replaces 2N6312. Used with part numbers 192161 and 194354. (Item #: 108783, Ref: 192160) $42.00

Crankshaft Pulley - This crankshaft pulley is for models 8N, 9N, 2N tractors. Used with a pin style hub, supplied with four rubber bushings for hubs with 13/32 pins when being used with Front Mounted Hydraulic Pump. (Item #: 172929, Ref: 192152) $92.90

Crankshaft, Remanufactured, 9N6303A - For Ford tractor models 2N, 8N, 9N (all gas), Replaces Casting number 9N6303A, Our remanufactured crankshafts are cleaned, magnafluxed, measured and reground if necessary, the journals are then polished., For a New version of this sku use Item #: 100549, Additional Handling and Oversize Fees Apply To This Item, (Item #: 200169) $405.01

Cylinder Head - For 8N, 9N, 2N. All GAS 1939-1952. Cylinder Head. Replaces 8N6050, 8N6050A, 9N6050 (Item #: 121814, Ref: 8N6050A) $230.00

Cylinder Head Bolt - These bolts are 7/16 in diameter and 3 inches long. For 8N, 9N, 2N. 18 are used per tractor. Replaces 8N6065A (Item #: 135049, Ref: F8N6065A) $9.30

No
Picture
Cylinder Head, Remanufactured, 2N6050 - For Ford tractor models 2N, 8N, 9N, Replaces Ford Casting number 2N6050, 2NC6050, All with Side Mount Distributor, Our remanufactured cylinder heads are reconditioned and ready for assembly, Cleaned and tested for cracks, For a New version of this sku use Item #: 121814, (Item #: 203871) $136.01

No
Picture
Cylinder Head, Remanufactured, 8N6050, 9N6050 - For Ford tractor models 2N, 8N, 9N, Replaces Ford Casting number 8N6050, 9N6050, All with Front Mount Distributor, Our remanufactured cylinder heads are Cleaned and tested for cracks, For a New version of this sku use Item #: 121814, (Item #: 210443) $184.01

Cylinder Head Stud - Studs are 7/16 in diameter and 3 inches long (threads: coarse 7/16-14 fine 7/16-20). For 8N, 9N, 2N. 18 are used per tractor. Priced each. (Item #: 182477, Ref: 8N6065A) $8.20

NOTE

Distributors and Distributor Parts - These are located in the Electrical System parts section.

NOTE

Flywheel Bolt Kit - From 1939 through 1964, these bolts were used by Ford to attach the Flywheel to the Crankshaft. These are exactly like the originals. (Item #: 179185, Ref: 350645S) $18.80

Governor - Complete Governor Assembly with gasket, 3 arm, for 9N and 2N (1939-1947), without proofmeter drive. (Item #: 105388, Ref: 9N18200C) $235.71

No
Picture
Governor Ball - Fits 9N, 2N and 8N. 5/8 inch diameter ball. 4 used per tractor. Replaces 358081S. (Item #: 178097, Ref: 358081S) $0.90

Governor Centrifugal Assembly - Governor Internal Centrifugal Assembly. Fits 9N18200C or 8N18204B above, for 8N, 9N, 2N (1939 thru 1952). If your tractor has the proofmeter you will need to also purchase a roll pin at a local hardware store (0.314" O.D. x 0.750" Long) to drive the cable. (Item #: 105391, Ref: 9N8N18179CA) $152.00

Governor Compensating Spring - 3.7 inch length. For tractor models 9N, 2N. (Item #: 178032, Ref: 9N9827) $7.00

Governor Driveshaft Ball Stop Shim - This Governor Driveshaft Ball Stop Shim is 0.010 inches thick. It is used on 9N, 2N and 8N Governors. Replaces 9N18241. (Item #: 179807, Ref: 9N18241) $1.24

Governor Dust Seal - Replacement Governor Dust Seal. For tractor models 8N, 9N, 2N. (Item #: 169249, Ref: 9N18183) $7.90

Governor Housing - Governor Housing includes needle bearing, lip-type seal, bushing, and proofmeter drive cap with seal and nut. For 8N, 9N, 2N tractors built 1939 thru 1952. (Item #: 179209, Ref: 8N18085) $196.00

Governor Lever Spring - This Governor Lever Spring will fit tractor models 9N, 2N, 8N. (Item #: 178196, Ref: 9N18196) $5.40

Governor Lower Race Assembly Bearing - For tractor models 8N, 9N, 2N. (Item #: 179090, Ref: 9N18186B) $120.00

Governor Needle Bearing - For tractor models 8N, 9N, 2N. (Item #: 179092, Ref: 9N18182) $5.20

Governor Repair Kit, Basic - For 8N, 9N, 2N. Kit contains gasket, lower race assembly, ball bearing, C-clip, 3 shims and 4 governor balls (5/8 inch). (Item #: 178658, Ref: BOK12502) $157.87

Governor Repair Kit, Complete - For 9N, 2N and 8N. Kit contains lower race assembly, shaft assembly (with or without proofmeter), upper face assembly, ball bearing assembly, shim, drive shaft ball stop, governor balls (5/8 inch), bushings, mounting gasket, dust seal, C-clip. (Item #: 105392, Ref: CAPN12502A) $356.44

Governor Shaft - Shaft Assembly, with or without proofmeter. For 8N, 9N, 2N. (Item #: 179265, Ref: 9N8N18187A) $72.00

Governor Thrust Bearing - This Governor Thrust Bearing is used on Ford 9N, 2N and 8N tractors, 1939-1952. It replaces original part number 9N18192 (Item #: 179808, Ref: 9N18192) $3.00

Governor Upper Race Assembly - Upper Race Assembly. For 8N, 9N, 2N. Replaces original part number 9N18188B. (Item #: 179423, Ref: 9N18188B) $90.00

Hand Starting Crank - 8N, 9N, 2N Hand Starting Crank WITHOUT Spinner. Replaces 9N17040 and 2N178040A (Item #: 111921, Ref: 351010R31) $45.00

NOTE

Piston Rings - These are located in the ENGINE RINGS category.

NOTE

No
Picture
Pistons and Sleeves - Pistons and Sleeves are located in the "Pistons and Sleeves category" Use your "BACK" key and select this category. (Item #: Various) $107.00

Ring Gear, Flywheel - Fits all models Ford 1939 thru 1964; except Fordson Major and Dexta. This gear has 134 beveled teeth. Inside diameter is 11.994 inches and outside diameter is 13.552 inches. (Item #: 110232, Ref: 9N6384) $26.00

Rotating Valve Conversion Kit - Convert regular exhaust valves to the rotating type. For 8N, 9N, 2N - Kit contains (8) A0NN6500A adjustable tappets, (4) 8N6534B valve rotator kits, (4) 8N6505C exhaust valves, (8) EAM6518A valve locks. Does not include tappet wrenches. (Item #: 131643, Ref: 8N6546B) $240.00

R Seal Retainer - Retainer, for Rear Crankshaft Oil Seal. For tractor models 8N, 9N, 2N. Replaces 8N6335A (Item #: 111281, Ref: 91A6335) $11.10

Timing Gear, Camshaft - This Bolt-on type Aluminum Camshafts fits 8N, 9N, 2N thru 1952. (Item #: 121560, Ref: 7RA6256) $89.00

Timing Gear, Crankshaft - This Crankshaft Timing Gear replaces original part numbers: 48-6306, 48-6306A, 486306A . For tractor models 8N, 9N, 2N. 22 teeth. (Item #: 121562, Ref: 486306A) $50.00

Valve, Exhaust - Exhaust Valve using Solid Guide. Uses 7HA6518 lock. For tractor models 8N, 9N, 2N. (Item #: 128615, Ref: 8N6505A) $11.70

Valve, Exhaust, Free-rotating - Exhaust Valve for free-rotating type. Uses solid guide and EAM6518A lock. For tractor models 8N, 9N, 2N. (Item #: 108115, Ref: 8N6505C) $13.70

Valve Guide - Single Valve Guide. For 8N, 9N, 2N. (Item #: 108113, Ref: 8BA6510B) $5.90

Valve Guide Retainer - 120 CID 4 cylinder gas engines. For 8N, 9N, 2N. Sold individually. 8 used per engine. (Item #: 178042, Ref: 40-6512) $1.50

Valve Guide, Split - Set of 16 halves. This is the original Split, two piece guide used with the mushroomed top valves, Ford 9N and 2N 1939-1947. Also used on Ford Cars and Trucks 1932-1948. Replace 40-6510-S, 406510. (Item #: 183688, Ref: 40-6510-S) $116.00

Valve, Intake - This Intake Valve uses the one piece guide. Uses valve lock part number 7HA6518. For 8N, 9N, 2N. (Item #: 128658, Ref: 8BA6507A) $10.90

$Ford 9N Valve Key, Intake and Exhaust, 1\2$
Valve Key, Intake and Exhaust, 1/2 - Sold per 1/2 valve, order 2 per valve. 120 CID 4 Cylinder Gas Engines. NOT for Free Rotating Exhaust Valves. Sixteen required per engine. Used in 120, 134 and 172 CID 4 Cylinder Gas Engines. Replaces 42026D, 70206880, 42026DGV, 500327, 70206880GV, 7HA6518GV, A30004, G11929, 10A6440, 206880, RP42026D, VT3234. (Item #: 107088, Ref: 7HA6518) $0.60

Valve Key, Rotating Exhaust - Single valve key. 120 CID 4 cylinder gas engine. Valve Key for FREE ROTATING Exhaust Valves. For tractor models 8N, 9N, 2N. (Item #: 166558, Ref: EAM6518A) $0.98

Valve Rotator Assembly - Valve Rotator Kit for free-type valve 8N6505C. 1 used per valve. Kit contains 1 valve spring retainer (available in kit only), 1 rotator cap, 2 valve locks. For 8N, 9N, 2N with rotating valves. 4 used per engine. (Item #: 178973, Ref: 8N6534B) $13.40

Valve Seat, Exhaust - These Valve Seats are the Nickel Series which are made for all new fuel blends. For tractor models 8N, 9N, 2N. 1.348 inch outside diameter. (Item #: 178189, Ref: 218-7405) $10.70

Valve Seat, Intake - For tractor models 8N, 9N, 2N. (Item #: 184249, Ref: 218-7535) $3.30

Valve Service Kit - Contains: 8 valve springs, 8 valve guides-solid type and 16 valve locks. For 8N, 9N, 2N. (Item #: 184398, Ref: VSKF928N) $123.00

Valve Spring Retainer - These Valve Spring Retainers are for intake and exhaust for the 120 cubic inch, 4 cylinder gas engines. NOT for free type exhaust valve. Retainer for free type valve not furnished separately, order rotator kit 8N6534B. For 8N, 9N, 2N. Priced each. If you order 1, you will receive 1 retainer. Replace 8RT6514B 8 per engine. (Item #: 108114, Ref: 8BA6514) $3.00

Valve Spring with 1 Piece Guides - Sold individually, this valve spring is for the 120 CID 4 cylinder gas engine in the 9N, 2N and 8N. For use with Solid Valve Guides. (Item #: 172904, Ref: 8N6513) $2.20

Valve Spring with Split Guides - Sold individually, these valve springs are for120 CID 4 cylinder gas engine. Valve spring for use with split guides. For 8N, 9N, 2N. (Item #: 172904, Ref: 2NC6513) $2.20

Valve Stem Seal - Valve Stem Seal for valve guide in 120 CID 4 cylinder gas engine. For 8N, 9N, 2N. Priced each. 4 used per tractor. (Item #: 166703, Ref: 8BA6571) $0.60

Valve Tappet - ADJUSTABLE Tappet. Fits 8N, 9N, 2N. Note: Quantity 8 used in engine. Priced each. If you order 1, you will receive 1 tappet. (Item #: 128660, Ref: A0NN6500A) $15.50

Valve Tappet Wrench Set - For 8N, 9N, 2N. Valve Tappet Wrench (Set of 2). For adjustable tappets. Wrenches to adjust 91A tappets. Replaces 8WR1770, 8WR1770, T-6500-PR. Also used on Ford F-Series Trucks 1948-1953 and Ford Cars 1949-1951. (Item #: 113941, Ref: 8WR1770) $9.98

Engine Pistons and Sleeves

Cylinder Sleeve, .005 oversize .090 - Oversize replacement for .090 thickness sleeves for larger cylinder block holes. Outside sleeve diameter is 3.373, .005 larger than original. Sleeve is .0925 thickness to retain original piston bore of 3 3/16 inches. This sleeve has a small lip at the top, if your your block does not have a lip recess these will not work. For 8N, 9N, 2N. (Item #: 184442, Ref: S1137-2) $101.00

Cylinder Sleeve, .040 - For tractor models 8N, 9N, 2N. This sleeve is .040 inch thin-wall for 3 ring and 4 ring pistons. Measures 3.268 inches outside diameter, 3.1875 inside diameter. Priced as each. (Item #: 108160, Ref: C0NN6055B) $34.00

Cylinder Sleeve, .090 - This Cylinder Sleeve is for tractor models 8N, 9N, 2N. This Sleeve is .090 inch heavy-wall for 3 ring and 4 ring pistons. Measures 3.368 inches outside diameter, 3.1875 inside diameter. Priced as each. (Item #: 128659, Ref: 8N6055B) $31.00

Piston, 3 Ring - For tractor models 8N, 9N, 2N. This is a Single 3 Ring Piston with standard bore can be used with .040 thin wall sleeves or .090 thick wall sleeves, and a 3/16 oil ring. (Item #: 172748, Ref: 8N6108B) $26.60

$Ford 9N Piston, 4 Ring, With 3\16 Oil Ring$
Piston, 4 Ring, With 3/16 Oil Ring - For tractor models 8N, 9N, 2N. This is a single piston with a standard 3 3/16 inch bore, 3/16 oil ring. Piston comes with pin and lock. (Item #: 184244, Ref: P1003) $91.00

Piston Pin Bushing - For tractor models 8N, 9N, 2N. This Piston Pin Bushing is .735 inch inside diameter. Price shown is EACH, minimum order quantity is 4. (Item #: 166831, Ref: 21A6207A3) $4.80

No
Picture
S1135A Sleeve - Finished, bored and honed (Tisco S1135-A). For 8N, 9N, 2N. (Item #: 108160, Ref: C0NN6055B) $34.00

Sleeve and Piston Kit - Sleeve and Piston Kit for 1 cylinder for 3 Ring Piston and .040 sleeve. Contains sleeve, piston, piston rings, piston pin and pin retainer. For 8N, 9N, 2N. Standard Bore. (Item #: 128661, Ref: SAT3A) $89.00

Sleeve and Piston Kit - Sleeve and Piston Kit for 1 piston with a 3 Ring Piston and .090 sleeve. Contains sleeve, piston, piston rings, piston pin and pin retainer. For 8N, 9N, 2N. (Item #: 163980, Ref: SAT6A) $86.00

Sleeve and Piston Kit - Sleeve and Piston Kit for 1 cylinder with a 4 Ring Piston and .090 sleeve. Contains sleeve, piston, piston rings, piston pin and pin retainer. For 8N, 9N, 2N. (Item #: 185521, Ref: SAT5A) $157.08

Sleeve and Piston Kit, For Single Cylinder - Kit, sleeves .090 wall thickness, pistons and rings. For 8N, 9N, 2N (Item #: 163980, Ref: APN6055A) $86.00

Engine Rings

Piston Ring Set - 3.270" Overbore - 4 Cylinder - For Ford tractor models 2N, 8N, 9N, Compatible with Ford Engine (s) 120 (gas), Replaces Ford OEM number 2C7583, Overbore: 3.270", Ring Size: Standard, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (2) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, 4th Groove Size: .188", 4th Groove Style: Cast Iron Oil, Sold as a complete 4 cylinder set, (Item #: 129090) $244.00

Piston Ring Set, 3 Ring - For tractor models 8N, 9N, 2N. 1939-1952 4 cylinder gas Standard Bore, CHROME Top Ring, 2@3/32 comp, 1@3/16 oil. Complete set for one cylinder. (Item #: 120804, Ref: 8N6149G1) $13.20

Piston Ring Set, 3 Ring - For tractor models 8N, 9N, 2N. 1939-1952 4 cylinder gas Standard 3 Ring, CHROME top ring, 5/32 steel rail oil. Complete set for one engine. (Item #: 129213, Ref: 9N6149A) $79.00

Piston Ring Set, 3 Ring, Plain - For 8N, 9N, 2N. 1939 to 1952 4 cylinder gas. Standard, plain top ring, 3/16 inch steel rail oil. Complete set for one engine. (Item #: 184767, Ref: 8N6149A5) $69.00

Piston Ring Set, 4 Ring - Chrome .040 inch oversize, 3/16 inch steel rail oil. For 8N, 9N, 2N. Complete for 1 engine, 4 cylinders. (Item #: 184800, Ref: PR1003-040) $110.00

Piston Ring Set, 4 Ring - For tractor models 8N, 9N, 2N. 1939-1952 4 cylinder gas standard bore, cast iron rings, 2@3/32 comp, 2@5/32 oil. COMPLETE SET FOR 1 ENGINE. (Item #: 128910, Ref: 2N6149-4RS) $158.00

Piston Ring Set, 4 Ring - Chrome. For Ford 8N, 9N, 2N tractors (1939-1952 with 4-cylinder flat head engines) For 4-ring center pin pistons. Std 3-3/16 inch bore, chrome top ring, 2 at 3/32 inch and 2 at 5/32 inch. COMPLETE SET FOR 1 ENGINE. (Item #: 129062, Ref: 2N6149G1) $140.00

Piston Ring Set, 4 Ring - For tractor models 8N, 9N, 2N tractors (1939-1952 with 4-cylinder flat head engines) For 4-ring pistons. Std 3-3/16 inch bore, 2 at 3/32 inch plain top rings and 2 at 3/16 inch oil rings. Complete for 1 engine, 4 cylinders. (Item #: 184018, Ref: PR1003) $164.00

Piston Ring Set - Standard - 4 Cylinder - For Ford tractor models 2N, 8N, 9N, Compatible with Ford Engine (s) 120 (gas), Bore: 3.1875", Ring Size: Standard, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (2) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, 4th Groove Size: .188", 4th Groove Style: Cast Iron Oil, Sold as a complete 4 cylinder set, For single cylinder set use Item #: 120808, (Item #: 128923) $133.00

No
Picture
Piston Ring Set - Standard - 4 Cylinder Set - For Ford tractor models 2N, 8N, 9N, Compatible with Ford Engine (s) 120 (gas), Replaces Ford OEM number 86537022, Bore: 3.1875", Ring Size: Standard, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold as 4 Cylinder Piston Ring Set, For Piston Ring Set - Standard - Single Cylinder use Item #: 120804, (Item #: 174335) $53.00

Piston Ring Set - Standard - Single Cylinder - For Ford tractor models 2N, 8N, 9N, Compatible with Ford Engine (s) 120 (gas), Bore: 3.1875", Ring Size: Standard, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (2) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, 4th Groove Size: .188", 4th Groove Style: Cast Iron Oil, Sold per cylinder, For complete 4 cylinder set use Item #: 128923, (Item #: 120808) $35.30

Exhaust System

Bracket, Muffler - Bracket, Rear Muffler. EXACT reproduction of ORIGINAL rear muffler bracket. For tractors: 8N, 9N, 2N {1939-1952}. (Item #: 153914, Ref: 9N5260) $19.10

Exhaust Manifold Gasket Set - For exhaust manifold on 8N, 9N, 2N. (Item #: 101514, Ref: 9N9448) $5.60

Extension Pipe - Vertical Two-Piece Exhaust Pipe with clamp, less muffler. For use without muffler, straight through design for maximum exhaust flow-more power. Vertical height remains the same as assemblies with muffler. Inlet 1-1/2 inch inside diameter. Outlet 1-1/2 inch outside diameter. For 8N, 9N, 2N. (Item #: 115466, Ref: M104) $43.20

Intake and Exhaust Manifold - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 9N9425, 9N9425W2G, (Item #: 101513) $70.00

Manifold - High Quality Intake and Exhaust Manifold with 2 Manifold Gaskets. For 8N, 9N, 2N. Replaces: 9N9425. This part may not be painted as shown. Cosmetic surface rust is common on bare castings. (Item #: 183860, Ref: 9N9425WG) $81.00

Manifold Nut and Washer Kit - Brass Nut and Washer Kit (Kit contains 4 nuts and 4 Washers). For intake and exhaust manifold. For tractors: 8N, 9N, 2N {1939-1952}. Replaces: Nut (7/16 - 20): 33816S, 7/16 LOCK WASHER: 34808S. (Item #: 118758, Ref: 33816-KIT) $6.00

Muffler - Heavy-Duty Horizontal Muffler only. Inlet 1-1/2 inch inside diameter, outlet 1-1/2 inch outside diameter, body length 23 inches, overall length 34 inches. For 8N, 9N, 2N. Does not come with hardware. (Item #: 102440, Ref: M1002) $40.60

Muffler - Vertical Muffler. Inlet 1-1/2 inch inside diameter. Outlet 1-1/2 inch outside diameter. For 8N, 9N, 2N. (Item #: 100569, Ref: M102-0) $36.00

Muffler - Vertical Two-Piece, Muffler and Pipe with clamp. Custom design ready for assembly. Pipe inlet flared, outlet 1-1/2 inch outside diameter. For 8N, 9N, 2N (Item #: 100568, Ref: M102) $78.00

Muffler - For Ford tractor models 2N, 8N, 9N (1939-1952), Replaces manufacturer number FO-20, Muffler Mount: Horizontal, Overall Length: 34", Shell Diameter: 3-1/4", Shell Length: 23", Inlet I.D.: 1-1/2", Inlet Length: 2-1/2", Outlet O.D.: 1-1/2", Outlet Length: 8-1/2", Used To Replace Muffler In Horizontal Exhaust System, Color: Silver, Inlet Clamp use Item #: 108865, (Item #: 100566) $47.24

Muffler and Pipe Assembly - Horizontal Muffler and Pipe, one piece welded assembly. For 8N, 9N, 2N with under-hood exhaust. WELDED 1 PIECE ASSEMBLY; MUFFLER AND EXHAUST PIPE INLET LENGTH 2 1/2 inches, INLET INSIDE DIAMETER 1 1/2 inches, SHELL LENGTH 23 INCHES, SHELL DIAMETER 3-1/4 INCHES, OUTLET LENGTH 8 1/2 INCHES, OUTLET OUTSIDE DIAMETER 1 1/2 InchES. OVERALL LENGTH 53 InchES, EXHAUST PIPE: FLARED INLET VERTICAL LENGTH 15 1/2 InchES, HORIZONTAL LENGTH 22 INCHES, OUTLET OUTSIDE DIAMETER 1 1/2 INCHES. (Item #: 100565, Ref: 8N5230) $37.00

Muffler and Pipe Assembly - Vertical one-piece Muffler and Pipe Assembly, custom design. For 8N, 9N, 2N. Pipe inlet flared, outlet 1-1/2 inch outside diameter. (Item #: 100567, Ref: M200) $73.00

Muffler and Pipe Assembly OEM - Just like the original, this Muffler Assembly includes the FoMoCo Script and original part number. Used on Ford 9N, 2N and 8N tractors, 1939-1952. Replaces 8N5230. (Item #: 183686, Ref: 8N5230S) $108.00

Muffler Clamp - Flanged Muffler Clamp. For tractor models 8N, 9N, 2N. Note that there is a large bevel and a small bevel on the inside edge of this clamp. The large side goes toward the manifold. If you install the clamp and the pipe is loose, you have it backwards. If you over-tighten, it will break. Replaces CAPN5200A (Item #: 101515, Ref: FP185) $4.90

Vertical Exhaust Pipe - For Ford tractor models 2N, 8N, 9N, Inlet I.D.:1-3/8", Vertical Length:29", Horizonal Length:13-1/2", Outlet O.D.:1-1/2", Use With 115466, (Item #: 120192) $40.30

Fuel System / Air Intake

Air Cleaner Assembly - This air cleaner assembly fits 9N, 8N. Includes Air cleaner, and cup with mesh. Will not accurately replace the style with the top wire mesh without modification. This Assembly has a solid cap with hole which can be cut off and replaced with a similar screen and lid or left as is, depending on the needs of the user. This assembly may come painted PRIMER or painted red depending on current supply. (Item #: 116910, Ref: 8N9600B) $105.65

Air Cleaner Cap - This Air Cleaner Cap is used with either Donaldson or United Specialties air cleaners found on some 9N and 2N tractors. Used with vertical air intake through hood. Fits outside of the pipe. 1.75 Inch Inside Diameter, 4.25 Inch Body Outside Diameter. (Item #: 111657, Ref: 351189R91) $40.00

Air Cleaner Cup Gasket - For air cleaners with thumb screw clamp (15-1/4 inches long). Tractors: 8N, 9N, 2N, (1939-1952). (Item #: 178045, Ref: 9N9623A) $6.00

Air Cleaner Cup Gasket - For air cleaners with toggle clamps on side of air cleaner (14-3/4 inches long). Use with Air Cleaner Cup S.61648 and S.60583. For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900. (Item #: 111390, Ref: 9N9623B) $7.90

Air Cleaner Cup Set - Includes Air Cleaner Cup, inner cup, clamp. VERIFY MEASUREMENTS. Cup inside diameter is approximately 4.5 inches, cup height is 3 inches. Replaces 311507. (Item #: 185529, Ref: 696300) $39.00

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $12.70

Air Cleaner Hose Clamp - Clamp, air cleaner to carburetor pipe. Tractors: 8N, 9N, 2N, NAA (1939-1954). For 2 inch outside diameter hoses +/- 1/8 inch. (Item #: 178020, Ref: 9N9653) $3.00

No
Picture
Air Cleaner Oil Cup - This cup is for Clamp Type Air Cleaners. This cup measures 4 3/4 inches outside diameter at the lip. The height is 3 inches. Please measure before ordering to ensure the proper fit. For models 2N, 9N, 501, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 850, 900, 950, 960. Replaces: 311507. (Item #: 111005, Ref: 311507) $11.98

Air Cleaner Tube - For tractor models 8N, 9N, 2N. Air Cleaner Tube, Air Cleaner to Carburetor. Chromed Steel Construction. Replaces: 9N18215C (Item #: 111282, Ref: 9N18215C) $17.50

Air Hose to Carburetor - 1.5 Inches - For 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900 1939-57 gas tractors. Rubber Air Hose is 2 3/8 inches long, 1 1/2 inch inside diameter. (Item #: 149842, Ref: 9N9652) $3.10

Carburetor - With reversible linkage. This Zenith carburetor outperforms the original carbs used on: 8N, 9N, 2N, 1939-1952. New Zenith carb replaces TSX33, TSX241B, TSX241A, TSX241C and OEM# 8N9510C. Center to center on the 2 mounting bolts is 2 1/4 inches. Made in USA, 1 year warranty. (Item #: 184201, Ref: 13876) $426.00

Carburetor - For 8N, 9N, 2N, ALL 1939-1952 - Original Marvel-Schebler design replaces TSX33, TSX341B, TSX431C. (Item #: 100763, Ref: 8N9510C) $123.00

Carburetor Elbow and Strainer - For tractor models 8N, 9N, 2N, NAA, NAB, Jubilee, 600 series, 700 series, 800 series. VERIFY FITTING DIMENSTIONS. Fits Marvel and some Carter UT Series carburetors. Used with flair fitting, not compression fitting. Male end (screen end) is 1/8 inch pipe threads. Female end is 1/4 inch flair. (Item #: 110005, Ref: 9N9553) $5.50

Carburetor Float, Small Bowl - Small Bowl Carburetor Float for Marvel Schebler carbs (2 3/8 inches at widest point of outside edge of floats) used on 9N, 2N and 8N tractors AND used only on the following engines (year): 134 CID (1953 to 1954) or 172 CID (1955 to 1957) gas engines on tractors: NAA, 501, 601, 700, 701, 800, 801, 900, 901, 2000. (Item #: 108449, Ref: 9N9550A) $9.60

Carburetor Gasket Set - For tractor models 8N, 9N, NAA, Golden Jubilee, Jubilee, 600, 800, 2N, 620, 630, 640, 650, 660, 700, 740, 820, 840, 850, 860, 900, 950, 960, NAB with the following Marvel Schebler carburetors: TSX101, TSX126, TSX133, TSX137, TSX144, TSX151, TSX161, TSX171, TSX179, TSX197, TSX211, TSX241A, TSX241B, TSX241C, TSX246, TSX258, TSX290, TSX297, TSX301, TSX33, TSX341, TSX37, TSX38, TSX407, TSX420, TSX423, TSX44, TSX447, TSX453, TSX481, TSX55, TSX577, TSX580, TSX593, TSX69, TSX748, TSX76, TSX765, TSX771, TSX787, TSX79, TSX80, TSX818, TSX827, TSX83, TSX94, TSX976, TSXU829, TSXU832, TSX198, TSX241, TSX241A, TSX241B, TSX241C, TSX305, TSX319, TSX420, TSX428, TSX500, TSX551, TSX577, TSX580, TSX593, TSX692, TSX706, TSX771, TSX976, TSXU834 (Item #: 182465, Ref: 9N9502) $4.20

Carburetor Idle Jet - Used on original Marvel Schebler carburetors 1939-1950. Ford 9N, 2N and (8N through serial numbers 250596 with the original carburetor). (Item #: 182917, Ref: 9N9596) $3.00

Carburetor Kit, Basic - Kit includes needle and seat, float lever pin, seal, gaskets and instructions. Repairs 61, 68 and 161 series Zenith carburetors. For Zenith 13876, 10457, 12566, 12566B, 13876, 12522, 12522B, 13878, 13877 (Item #: 183586, Ref: BK44V) $27.60

Carburetor Kit, Basic - For TSX33, TSX241A, TSX241B and TSX241C carburetors on 2N, 8N and 9N tractors. Contains float valve, float lever pin, and gaskets for minor carburetor overhaul. (Item #: 112350, Ref: BK45V) $15.60

Carburetor Kit, Complete - For tractor models from 1939 to 1952, carburetor part #: Marvel-Schebler TSX33, Ford 9N9510A. Kit contains all parts necessary for major carburetor overhaul, including a Viton float valve. For 8N, 9N, 2N. Does NOT include float. (Item #: 112445, Ref: C545V) $26.60

Carburetor Kit, Complete - For tractor models from 1939 to 1952, carburetor part #: Marvel-Schebler TSX241A, TSX241B, and TSX241C, Ford 8N9510C. Kit contains parts necessary for major carburetor overhaul, including a Viton float valve. For 8N, 9N, 2N. Does Not include Float. (Item #: 112445, Ref: C546V) $26.60

Carburetor Kit, Comprehensive - For Marvel-Schebler carburetors: TSX33, TSX241A, TSX241B, TSX241C, TSX420 Ford 9N, 2N, 8N. Contains all the parts shown. (Item #: 182486, Ref: R7848) $56.00

Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: TSX33, TSX241B, TSX241A, 8N9510C. For the following tractor models: 8N, 9N, 2N. Center-to-Center on the mounting bolts is 2 1/4 inches. Add $50.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203252, Ref: 1302-CARB) $335.00

No
Picture
Carburetor Repair Kit - Carburetor Repair KIT For 8N, 9N, 2N (Item #: 112350, Ref: BK45V) $15.60

Carburetor Throttle Shaft and Lever - For Marvel Schebler carburetor on 8N, 9N, 2N. (Item #: 182771, Ref: 9N9581A) $12.60

Carburetor Venturi - Venturi for original Marvel Carburetors. For tractor models 8N, 9N, 2N. Carb Mfg #s - : TSX101, TSX126, TSX133, TSX137, TSX144, TSX151, TSX155, TSX161, TSX171, TSX179, TSX197, TSX211, TSX241A, TSX241B, TSX241C, TSX246, TSX258, TSX290, TSX297, TSX301, TSX33, TSX341, TSX37, TSX38, TSX407, TSX420, TSX423, TSX44, TSX447, TSX453, TSX481, TSX516, TSX55, TSX69, TSX732, TSX748, TSX76, TSX787, TSX79, TSX80, TSX818, TSX827, TSX83, TSX94, TSXU829, TSXU832 (Item #: 111831, Ref: C5NN9586B) $12.00

Choke Control Rod Assembly - Pre-bent Choke Control Rod is 29 1/2 inches long. Does NOT come with knob. For tractors: 8N, 9N, 2N (1939-1952). See part number 9N9815 for Throttle to Governor Rod. (Item #: 126114, Ref: 9N9700) $27.00

Choke Knob - For Ford Gas Tractors 1939-1964. Fits models: NAA, Jubilee, 2N, 8N, 9N, 501, 600, 601, 6411, 700, 701, 801, 900, 901, 2000, 4000. Replaces 9N9703, 9N9703B. 10-32 thread. (Item #: 178058, Ref: 9N9703) $5.40

Choke Lever and Shaft - For tractor models 8N, 9N, 2N. (Item #: 179083, Ref: 9N9546) $15.10

Choke Retainer Spring - Used on original Marvel Schebler TSX33, TSX241A, TSX241B, and TSX241C (Item #: 108474, Ref: 9N9539) $2.50

Cyclone Air Cleaner Glass Jar - For 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000, all 1939 to 1964. Cyclone Air Cleaner Glass Jar (jar only) screw on type. Exactly like original for tractors that used the "Cyclone" air cleaner only. (Item #: 178043, Ref: 230056) $34.20

No
Picture
Cyclone Air Cleaner Glass Jar Seal - Cyclone Air Cleaner Glass Pint Jar Seal (Item #: 184394, Ref: ACP1248) $2.30

Cyclone Cup and Spring Assembly - Only for those tractors (1939 to 1964) that used the CYCLONE Air Cleaner Assembly which MAY include: 8N, 9N, 2N, NAA, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000. Verify the type of air cleaner you have before ordering. (Item #: 178172, Ref: 230053) $18.10

Friction Disc for Throttle Control Lever - This Throttle Friction Disc is 3 inches in diameter and has a 1/2 inch center hole. Replaces part number C5NN518B, 83924272, 83977032, 9N518, E6NN9R536AA, 311503. (Item #: 111446, Ref: C5NN518B) $1.80

Fuel Cap - Original Style Cap. Fits 8N, 9N, 2N. Fuel Cap for self venting tanks. Cap is non-vented. (Item #: 111721, Ref: 9N9030Z) $7.20

Fuel Cap, Non-Vented - This Silver Fuel Cap is for models 8N, 9N, 2N, 600, 620, 630, 640, 650, 660, 800, 820, 840, NAA Fuel Cap. Verify OEM number to ensure correct fit. (Item #: 185782, Ref: D5NN9030A) $9.10

Fuel Cap, Vented - 2-7/8 inch outside diameter, silver finish, 1-3/4 inch edge of tang to edge of tang, vented, includes gasket. For tractor models 8N, 9N, 2N, NAA, NAB, 501, 541, 600, 601, 700, 701, 800, 801, 900, 901, 1801, 1811, 1821, 1841, 1871, 1881, 2000, 2030, 2031, 2100, 2110. (Item #: 184806, Ref: C5NN9030D) $9.00

Fuel Line - For tractor models 8N, 9N, 2N (1939-1952). This Fuel Line is from Sediment Bowl to Carburetor. Consists of: 1/4 inch steel tubing with two 1/4 inch inverted flair fittings installed. (Item #: 155281, Ref: 9N9282A) $17.00

Fuel Line Anti-Rattler - For 8N, 9N, 2N 1939-1952. Fuel Line Anti-Rattler between fuel line and tank. Restoration Quality. (Item #: 126646, Ref: 9N9121A) $6.00

Fuel Sediment Bowl Assembly - For models 8N, 9N, 2N, NAA and Jubilee with SHORT BOWL. The fuel bowl assembly has a 3/8 inch NPT male inlet and 1/4 inch pipe thread (7/16 -24)female outlet, 1-1/4 inch long bowl. Works with 9N9282A fuel line. Replaces 2N99155B and NAA9155B with short bowl. (Item #: 105381, Ref: 2NAA9155B) $14.00

Fuel Sediment Bowl Bail assembly - For tractors 8N, 9N, 2N, NAA, Jubilee. (Item #: 113631, Ref: 2N9166) $3.00

Fuel Sediment Bowl Valve Stem - Sediment Bowl Valve Stem with wheel complete. For tractor models 8N, 9N, 2N, NAA. (Item #: 178182, Ref: APN9194) $6.50

Fuel Sediment Glass Bowl - 2 inch Glass Bowl. Fits NAA9155B and 2N9155B sediment bowls. Uses gasket NAA9160A, not included. Fits 8N, 9N, 2N, NAA, Jubilee. (Item #: 105382, Ref: 9N9162) $3.20

Fuel Sediment Screen and Gasket - Gasket and Screen Set (for 2 inch outside diameter sediment bowl). Ford 8N, 9N, 2N, NAA, 600, 601, 700, 800, 801, 900. (Item #: 105383, Ref: 2NAA916061) $2.60

Fuel Tank Cap - Chrome - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 9N9030, Chrome, (Item #: 113551) $9.90

Fuel Tank, Used - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 9N9002, Length: 25", Width: 10", Height: 17", For OEM Style fuel cap use 111721, For a new version of this item use Item #: 103891, Additional Handling and Oversize Fees Apply To This Item, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 403891) $67.01

Gasoline Fuel Tank, Steel - Gasoline Fuel Tank (Steel) For 8N, 9N, 2N. 3/8 inch pipe thread outlet. This tank can use the 9N9030Z, D5NN9030A or C5NN9030D caps. (Item #: 103891, Ref: 9N9002) $117.00

Main Adjustable Needle - Main Adjusting Needle. For tractor models 8N, 9N, 2N. (Item #: 182853, Ref: 9N9565C) $6.80

Needle Valve - Viton Float Valve Needle, Seat and Gasket Assembly. Tractors: 8N, 9N, 2N, (1939 to 1952). (Item #: 111800, Ref: C3NN9564A) $8.10

Quadrant Throttle Plate - For tractor models 9N, 2N 1939-1947. (Item #: 178700, Ref: 9N9820) $30.70

Screw Kit 4 Per PKG - Screw Kit, air cleaner funnel to hood, set of 4 screws and speed nuts. For tractors: 8N {1948-1952}. (Item #: 179261, Ref: 32940-KIT) $4.70

Sediment Bowl Screen - For Ford tractor models NAA, 2N, 8N, 9N, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981 Replaces Ford OEM number 2N9161, , Compatible with Massey Ferguson tractor models Super 90 (gas s/n 888674- later), TO20, TO30, TO35 (gas), 35, 50 (gas), 65, 65 (gas), 85 (gas s/n 807751-earlier), 88, 88 (gas), Compatible with Massey Ferguson Construction and industrial models 202 (s/n 309328-earlier), 204 (s/n 343891-earlier), 302 (s/n 119700213-earlier), 304 (s/n 119750210-earlier), 356 (gas s/n 670001084-earlier), Square hole, For 2" O.D. sediment bowl, (Item #: 110833) $2.70

Throttle Body To Bowl Gasket - For Ford tractor models NAA, 2N, 8N, 9N, 501, 600, 700, 800, 900, 2000, 4000, Replaces Ford OEM number EAF9519A and C3NN9516A, (Item #: 111270) $1.00

Throttle Control Arm Assembly - For tractor models 9N, 2N. (Item #: 178154, Ref: 9N9805) $42.30

Throttle Control Rod Spring - For tractor models 9N, 2N. (Item #: 178085, Ref: 2N9806) $3.80

Throttle Rod - Rod, Throttle Control Rod and Socket. 2-1/2 inches long. Tractors: 9N, 2N (1939-1947). Replaces 9N9810 (Item #: 178075, Ref: 9N9810) $13.50

Throttle Rod - This Governor to Carburetor Control Rod Assembly is 7 inches long and has a ball receptacle on both ends. For tractors: 8N, 9N, 2N (1939-1952). (Item #: 165869, Ref: 9N9818A) $19.00

Throttle Rod - Rod, Throttle Shaft to Governor Rod Assembly is 10 5/8 inches long. For tractors: 9N, 2N (1939-1947) See part number 9N9700 for Choke Control Rod Assembly. Replaces 9N9815 (Item #: 166441, Ref: 9N9815) $32.65

Throttle Rod Spring Retainer - For tractor models 9N, 2N. (Item #: 178086, Ref: 9N9812) $4.30

Gauges

Ammeter - For all models to 1958. Terminal type ammeter. 30-0-30. Chrome ring. Replaces FAD10850A. Fits 2 inch opening. (Item #: 121632, Ref: A0NN10670A) $7.00

Oil Gauge Adapter Fitting - This Oil Gauge Adapter Fitting is 1/8 inch NPT female to 3/16 inch tubing female. It is used on some gauges without removable fitting. (Item #: 178157, Ref: 9N18685) $4.90

Oil Line, Junction Block to Gauge - This is a pre-formed steel Junction Block to Oil Pressure Gauge line. It is used on Ford 9N and 2N tractors, 1939 to 1947. It replaces original part number 9N18676. (Item #: 183012, Ref: 9N18676) $18.00

Oil Pressure Gauge - For tractor models: 8N, 9N, 2N, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 850, 2000, 4000, NAA, Jubilee. All before 1964. Oil pressure gauge, 40 pounds, 2 inch body diameter. Replaces OEM numbers Ford: FAD9273A and Massey Ferguson: 506902M92. (Item #: 113472, Ref: S.61171) $17.10

Oil Pressure Gauge, 50lb - For tractor models 8N, 9N, 2N. Oil Pressure Gauge, 50 lbs., 2 inch body diameter. (Item #: 150623, Ref: 9N9273A) $15.60

Oil Pressure Gauge, 50lb Black - For tractor models 8N, 9N, 2N. Oil Pressure Gauge, 0-50 lbs., for 2 inch diameter hole. (Item #: 103888, Ref: 9N9273A-BLACK) $12.00

Oil Pressure Gauge, 80 Pound, Black - For tractor models 8N, 9N, 2N, 541, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, (2000, 4000 4 cylinder), NAA, Jubilee, 1801. Black raised bezel, measures to 80 pound, dash or bracket mounted gauge with a bracket and studs 1/8 inch NPT thread. Replaces FAD9273A. (Item #: 121629, Ref: FAD9273A_Black) $11.60

Oil Pressure Gauge Black Bezel - For Ford tractor models NAA, 2N, 8N, 9N, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2031, 2111, 2130, 2131, 4000, 4030, 4031, 4110, 4120, 4121, 4130, 4140, Replaces Ford OEM number FAD9273A, Raised Black Bezel, Black Face, Dash Mounted, 1/8" Male Pipe Threads, 0 - 80 PSI, Oil Pressure Gauge - Chrome Bezel use Item #: 110411, (Item #: 121629) $11.60

Tac Connector Bushing for Governor - For Ford tractor models 2N, 8N, 9N, (Item #: 185290) $8.50

Temperature Gauge Adapter Pipe - 3 5/8 inches long, 1 1/2 inches outside diameter. Uses 5/8 inch -18 UNF Temperature Gauge Lead. Installs in upper hose. Cut hose, slide new adapter pipe in place, drill 2 inch outside diameter hole in dash to mount gauge. For tractor models: 2N, 8N, 9N. (Item #: 178049, Ref: FDS2673) $55.00

Hitch / Drawbar

Chain - CHAIN, Fixed Drawbar Safety Chain Assembly, EXACT reproduction of ORIGINAL Drawbar Chain. FOR tractors: 8N, 9N, 2N, Jubilee, NAA (1939-1954). (Item #: 178494, Ref: 9N5370) $59.97

Crank Arm, Leveling Box - This Leveling Box Crank Arm is for tractor models NAA, Jubilee, 2N, 8N, 9N, 340, 420, 600, 700, 800, 900, 2000, 2100, 2600, 2610, 3000, 3100, 3400, 3550, 3600, 3610, 4000, 4110, 4600. Replaces 81822432, 81717231, C5NN594E, 957E594, 888607M1, 1662382M1, 181349M1 (Item #: 172986, Ref: C5NN594E) $9.10

Drawbar Link Check Chain Anchor - Anchor, Drawbar Link Check Chain (pair- one right and one left). For Dexta, NAA, Super Dexta, Jubilee, 2N, 8N, 9N, 600, 700, 800, 900, 2000, 2600, 2610, 3000, 3600, 3610, 4000, 4600, 4610. (Item #: 186635, Ref: 957E5967) $21.60

Eyelet Assembly, Check Chain - This Check Chain Eyelet Assembly fits Many Ford Tractors. The Bolt length is 2 11/16 inches. Thread diameter is 1/2 inch. Eyelet is 1/4 inch diameter. Replaces EC0N660A, NCB660A (Item #: 111911, Ref: EC0N660A) $5.20

Level Box Fork - Right - Fork, Hydraulic Lift Leveling Rod, right hand. Length 10-1/4 inches. For 8N, 9N, 2N, Jubilee, NAA. (Item #: 108897, Ref: 9N585A) $29.90

Level Box Handle - Lever Handle. For Jubilee, NAA, 2N, 8N, 9N, 501, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 850, 900, 950, 960, 2000, 4000. (Item #: 172986, Ref: 9N594) $9.10

Leveling Box Assembly, Left - Left Hand Rod and Fork Assembly, hydraulic lift, left hand. For 8N, 9N, 2N, NAA, Jubilee, tractors. 1939 to 1954. 18 to 22 Inches Center to Center adjustablility. (Item #: 115097, Ref: 8N564B) $59.98

Leveling Box Assembly Less Fork - For Ford tractor models NAA, 2N, 8N, 9N, 600, 700, 800, 900, 2000, 4000, Replaces Ford OEM number 8N577A, 180854M91, Without fork, For 14-3/4" Fork use Item #: 108897, (Item #: 107886) $66.00

Leveling Box Assembly, Right - This Right Hand Leveling Box Assembly uses 5/8 inch pins and opens center-to-center from 17.75 to 21.5 inches. Adjusts 21.5 inches. Width of the fork is 9/16. For 8N, 9N, 2N, NAA, Jubilee. (Item #: 113624, Ref: 8N577A) $56.00

Leveling Box - Economy - For tractor models 8N, 9N, 2N, NAA, Jubilee, Dexta, Super Dexta. Working length of 19.5 to 27 inches. Pin holes are 3/4 inch. (Item #: 154104, Ref: ECON577AB) $47.71

Leveling Box Gear - Gear, Leveling Box Pinion. For 2000, 2N, 3000, 4000, 501, 600, 700, 800, 8N, 900, 9N, Jubilee, NAA. (Item #: 129284, Ref: B9NN568A) $9.60

Leveling Box Knuckle Pin - MUST ORDER IN QUANTITY 2, PRICED EACH. For tractor models NAA, 600, 601, 700, 701, 800, 801, 801, 701, 801, 900, 901, 8N, 9N, 2N all built 1939 to 1964, (2000, 3000, 4000 1965 and up), (3600, 4600 1975 and up). 5/8 inch pin diameter, 2 7/8 inch usable length. Takes our 3/16 inch linchpin (part number DKP316). MUST ORDER IN QUANTITY OF 2, PRICED EACH. (Item #: 111799, Ref: 9N595) $2.80

Leveling Box Knuckle, Right - Knuckle, Right Hand Leveling Assembly. Pin holes are 5/8 of an inch. The shape of the one pictured may vary slightly from different manufacturers. For tractor models NAA, Jubilee, 2N, 8N, 9N, 501, 600, 700, 800, 900, 2000, 3000, 3600, 4000, 4600. Uses 2 pins part number 9N595. (Item #: 165379, Ref: 957E566) $10.20

Leveling Box Shaft - This Leveling Box Shaft and Gear measures 14 inches long with thread length of 4 inches. Diameter is 3/4 inches. For Jubilee, NAA, Dexta, Super Dexta, 2N, 8N, 9N, 600, 700, 800, 900, 2000, 4000. (Item #: 113926, Ref: NCA579B) $15.10

Leveling Box Yoke Rod, LH - Left hand side. Rod diameter is .750 inches. For tractor models NAA, Jubilee, 2N, 8N, 9N, 30, 340, 420, 600, 620, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, 2000, 2100, 2600, 2610, 3000, 3100, 3400, 3550, 3600, 3610, 4000, 4110, 4600. (Item #: 115632, Ref: C5NNB863A) $21.60

Leveling Rod, Left Hand - Lift Link, left hand, non-adjustable. Hole centers approximately 20 inches. Replaces 9N564B, C5NN564B. (Item #: 111007, Ref: 182544M92) $45.00

Lift Arm - 32 Inch - Cat 1 - Lower Lift Arm, heavy-duty, with forged ball-joint ends. Category I accommodates 7/8 inch drawbar or lower link pins. Length 32 inches. For tractor models 8N, 9N, 2N, Golden Jubilee and NAA. Used left or right side. (Item #: 191125, Ref: JSA1002B) $48.00

Lift Arm, Lower - Category 1 lower lift are will replace the Left or Right. Uses 7/8 pin. For 8N, 9N, 2N, NAA, Jubilee. Lower 3-Point lift Arm. Center to Center measurement 32 inches. One half inch width. Color may vary. (Item #: 103208, Ref: 9N555B) $48.00

Lower 3-Point Pin Support Plate Gasket - Two used per tractor, sold individually. For tractor models (9N serial number 6019 and up), (2N mid 1939-1947). (Item #: 178126, Ref: 9N523B) $4.30

Lower Link Support Shaft with Hardware - For 9N, 2N Lower Link Support Shaft anchors lower lift arm to tractor. Comes with nuts and hardware. (Item #: 125686, Ref: 9N563KIT) $24.40

Stabilizer Arm - Stabilizer arm measures length 31-1/2 inches center to center. For tractor models 2N, 600, 800, 8N, 9N, Jubilee, NAA, 2000 (4 cylinder), some 4000 (4 cylinder). Color of part can be red or primer depending on supply. (Item #: 110516, Ref: 230042R) $15.30

Stabilizer Arm Blue - Arm only, blue. 31.50 inches center to center on holes. 7/8 inch pin holes. Replaces 230042 (Item #: 180774, Ref: 230042B) $20.10

Stabilizer Bracket - Used on the left or right side, this bracket has mounting bolt hole spacing of 5 inches on center. It is 6.75 inches long and 0.375 inches thick. This part replaces 231254, C5NNN928D, 181775M1, 181775M91, 181776M91. Color varies. This part may arrive Red, Blue, or Black. (Item #: 111709, Ref: 231254) $13.00

Stabilizer Kit - 3 Point - Kit contains Stabilizer Brackets, Stabilizer Pins, Stabilizer Arms (Category 1). Comes primered (color may vary). Prior to painting check fitment. Compatible with Ford Tractor(s) NAA, 2N, 8N, 9N, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881 (Item #: 152386, Ref: 231253) $60.00

Stay Strap, Lower - For 8N, 9N, 2N, NAA, 600, 700, 800, 900. Stay Strap - Lower. (R3575). Color varies. Replaces 9N5375B (Item #: 179230, Ref: 9N5375B) $14.70

Stay Strap, Lower Red - For 8N, 9N, 2N, NAA, 600, 700, 800, 900. Stay Strap - Lower. (Item #: 111112, Ref: 9N5375) $6.98

Stay Strap, Upper Blue - Painted blue, 25.500 inches long, .250 inches thick, 1.500 inches wide, .937 inch hole, .613 inch x 6.625 inch slot. For tractor models 600, 700, 800, 8N, 900, 9N, NAA. (Item #: 111113, Ref: 9N5374B) $8.30

Stay Strap, Upper Red - For 8N, 9N, 2N, NAA, 600, 700, 800, 900. Stay Strap - Upper. (Item #: 111113, Ref: 9N5374) $8.30

Thrust Bearing - Leveling Box Assembly Bearing. For 2N, 8N, 9N, 501, 600, 700, 800, 900, 2000, 3000, 3600, 4000, 4600, Dexta, Super Dexta, Jubilee, NAA. (Item #: 179766, Ref: 9N554) $7.90

No
Picture
Top Link Bracket, Used - For Ford tractor models NAA, 2N, 8N, 9N, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 1800, 2031, 4031, 4120, 4121, 4130, 4131, 4140, Replaces Ford OEM number NCA535A, Drilled for 1" Pivot Pin, For a new version of this item use Item #: 126752, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435906) $36.00

Top Link Rocker - For 8N, 9N, 2N, NAA, Jubilee, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 800 Hi-clearance, 801, 811, 820, 821, 840, 841, 850, 851, 861, 871, 881, 2000 4 cylinder Hi-clearance, 4000 4 cylinder Hi-clearance. (Item #: 126752, Ref: NCA535A) $59.00

Hydraulic System

$Ford 9N 7\8 inch Hydraulic Pump Drive Flange$
7/8" Hydraulic Pump Drive Flange - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number L36-8, Round Bore, 2-1/4" Spacing, For Set Screw, (Item #: 111994) $77.68

Bushing - Bushing for Hydraulic Pump Base, for PTO Shaft. For 8N, 9N, 2N. (Item #: 172372, Ref: 9N649A) $26.10

Bushing Insert - Hydraulic Pump Bushing Insert. Measures Overall length is 1 1/16, big end diameter is 1/2, small end diameter is 3/8+, inside diameter is 1/4. (Item #: 173192, Ref: 192164) $2.98

Cam Block - For Hydraulic Pump, 9N, 2N and 8N (1939-1952). (Item #: 182638, Ref: 9N617A) $21.20

Chamber Kit - Repair kit for one Hydraulic Pump Chamber. Fits either left or right. For 8N, 9N, 2N. (Item #: 113990, Ref: 9N621KIT) $25.60

Draft Control Plunger - For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000, Dexta, Super Dexta. Fine Thread style. (Item #: 111890, Ref: 8N541B) $40.00

Draft Control Plunger Spring - This Draft Control Plunger Spring fits between the Hydraulic Plunger and Yoke. Fits 9N, 2N 8N, NAA, Jubilee, 600, 601, 800, 801, 2000, 4000 (except row crop), Dexta, Super Dexta. (Item #: 165989, Ref: 9N547B) $37.00

Draft Control Spring Plate - This Draft Control Spring Plate is used on Ford tractors from 1939 to 1964. It replaces: 81801555, 957E527, 9N527, NCA527A. I you need the plate with the pin, order 8N527. (Item #: 178070, Ref: 9N527) $16.30

Draft Control Spring Seat - Exact of original. Fits all models (1939 to 1964), NAA, Jubilee, Dexta, Super Dexta, 2N, 8N, 9N, 600, 601, 700, 701, 800, 801, 900, 2000, 4000. Replaces: 2N624, 957E624. (Item #: 178127, Ref: 2N624) $9.30

Draft Control Yoke - This Draft Control Yoke Fits 8N, 9N, 2N and fits with 8N541B. Fine Thread Style. (Item #: 111887, Ref: 9N546C) $30.00

Felt, Spring Seat - Hydraulic Lift Draft Control Spring Seat. For tractor models 8N, 9N, 2N, NAA, 600, 601, 700, 701, 800, 801, 900, 901, (1939-1962). (Item #: 178061, Ref: 9N529) $3.20

Friction Disc for Hydraulic Control Lever - Friction Disc for Hydraulic Control Lever, 3 inch diameter, 1/2 inch hole. For tractor models 2N, 8N, 9N, 600, 601, 700, 701, 800, 801, 900, 901, NAA, (2000 and 4000 4 cylinder). Price is for each. (Item #: 111446, Ref: C5NN518B) $1.80

Gasket, Hydraulic Cylinder to Center Housing - Hydraulic Cylinder Gasket measures 1 inch outside diameter and 7/16 inch inside diameter. For tractor models 8N, 9N, 2N. Priced each. (Item #: 172822, Ref: 9N552) $0.90

Gasket, Hydraulic Pump Drain - Hydraulic and Transmission Drain plug Gasket. 2 inch inside diameter. Fits Ford Tractors, 1939 to 1964. Replaces: 81804570, 8N7011. (Item #: 112227, Ref: 8N7011) $1.70

Hydraulic Lift Control Quadrant - For tractor models 8N, 9N, 2N. Hydraulic Lift Control Lever connects to this. Also fits NAA, Jubilee, 2000, 4000, 501, 600, 601, 700, 701, 800, 801, 900, 901. All 1939-1964 4 cylinder. Replaces 2N516A1, 2N516A2, 2N516B. Uses friction disc C5NN518B found on our web page. Bolt holes are 1/4 x 20. (Item #: 111910, Ref: 9N515) $29.90

Hydraulic Lift Cover Repair Kit - For 8N, 9N, 2N. Lift Cover Repair Gasket Kit. Gasket Set includes 2 valve chamber gaskets, lift cover gasket, piston o-ring, back up washer, base pump gasket, 2 inspection cover gasket cylinder to center housing cover, 2 hydraulic lift cylinder housing gasket. (Item #: 113537, Ref: LCRK928) $9.60

Hydraulic Lift Cylinder - For 8N, 9N, 2N. Hydraulic Lift Cylinder. Cylinder only. Can use 3 ring piston or o-ring type. Sold seperately. (Item #: 111928, Ref: 9N510D) $73.00

Hydraulic Lift Housing Gasket - For Ford tractor models 2N, 8N, 9N, Replaces Ford OEM number 9N502, (Item #: 112064) $4.30

Hydraulic Lift Level Indicator (Dip Stick) - 8N, 9N, 2N, NAA. Hydraulic Lift Level Indicator. (Item #: 111308, Ref: NAA927C) $5.60

Hydraulic Lift Lever - For tractor models 8N, 9N, 2N, NAA, 600, 601, 700, 701, 800, 801, 900, 901, (2000, 4000 4 Cylinder). (Item #: 178133, Ref: S.66598) $20.60

Hydraulic Lift Piston Connecting Rod - For Dexta, NAA, 2N, 8N, 9N, 2000, 3000, 4000, 600, 700, 800, 900. Replaces NCA526A and 957E526, 9N526. (Item #: 155017, Ref: 86563314) $32.40

Hydraulic Lift Piston O-Ring - For 8N, 9N, 2N. O-Ring used on piston part number NAA530B. Price is for each. Used with Lift Piston Washer part number NAA473A. NOTE: The leather washer goes on first, then the o-ring. (Item #: 116071, Ref: NAA533A) $1.70

Hydraulic Lift Piston Rings - Kit of 3, steel, fits piston part number 9N530B. For tractor models 8N, 9N, 2N. (Item #: 113940, Ref: 9N675) $10.80

Hydraulic Lift Piston Washer - For 9N, 8N, 2N. Hydraulic Lift Piston Washer used with Piston part number NAA530B. Price is for each. (Item #: 112216, Ref: NAA473A) $3.50

Hydraulic Lift Ram Arm - Hydraulic Lift Ram Arm fit the 8N, 9N, 2N. This part will work for the 9N, 2N and early 8N but does not look like the original. This does look like the original for the Late 8N. For an early 9N, this part may require additional machining, such as grinding down the end raised portion, and/or shortening one end 1/4 inch and adjusting with shims. (Item #: 111326, Ref: 8N545B) $71.00

Hydraulic Lift Shaft - For tractor models: 8N, 9N, 2N, NAA, Jubilee, 2000, 4000, 600, 601, 700, 701, 800, 801, 900, 901. Hydraulic lift shaft. [PLEASE NOTE: THIS SHAFT HAS 1 THREADED HOLE ON EACH END. IT WILL REPLACE OLDER STYLE USED ON 8N, 9N, 2N TRACTORS WITH 2 HOLES ON EACH END BUT WILL REQUIRE 2 WASHERS PART number NCA551A and (2) 7/16 inch-20 X 11/16 inch BOLTS. WASHERS AND BOLTS NOT CURRENTLY AVAILABLE FROM YESTERDAYS TRACTOR]. (Item #: 165431, Ref: NCA544B) $419.08

Hydraulic Lift Shaft Arm - For 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 850, 900, 950, 960, 2000, 4000 gas. (Item #: 114032, Ref: 9N543B) $52.00

Hydraulic Lift Shaft Bushing - This Hydraulic Lift shaft Bushing measures inside diameter 2.000 inches, outside diameter 2-3/8 inches, length 3.00 inches. Sold individually, 2 used per tractor. For tractor models 8N, 9N, 2N, NAA, 600, 620, 630, 640, 650, 660, 800, 820, 840, 850, 2000, 3000, 4114. Replaces 86534029, 9N531C (Item #: 173523, Ref: 9N531C) $14.20

Hydraulic Pump - For Ford tractor models 2N, 9N, The width of this pump at the valve chambers is 7-1/2 . For some tractors, minor grinding of the pump housing opening might be needed for installation., Replaces Ford OEM number 9N605A, (Item #: 140497) $424.00

Hydraulic pump base to center housing Gasket - For tractor models 8N, 9N, 2N. (Item #: 112062, Ref: 9N611) $2.20

Hydraulic Pump Drive Shaft - APPLICATION: 8N, 9N, 2N, SHAFT DIAMETER: 3/4 Inch, SHAFT OVERALL LENGTH: 13-1/16 InchES, END A TYPE: KEY, END A SIZE: 3/4 Inch, END B TYPE: LEFT HAND THREAD, END B SIZE: 5/8 Inch. END A mates to coupler L601-14. END B mates to hub 191196. (Item #: 112199, Ref: 190760) $23.10

Hydraulic Pump Drive Shaft - For tractor models 8N, 9N, 2N. 3/4 inch shaft diameter, 13 inches in length, 6 spline on one end and .187 inch keyway on other end. Mates with end hub 192161 or 54C2055. Other end mates with coupler L601-14. (Item #: 111595, Ref: 194354) $31.90

Hydraulic Pump Hub - Hydraulic pump hub for Sherman 54 series loader. Hydraulic pump hub 3 7/8 inch outside diameter, 2 3/4 inches center to center on holes. 6 spline center bore, 3/4 inch inside diameter, 7/16 inch smooth ID mounting holes. (Item #: 111639, Ref: 54C2055) $39.98

Hydraulic Pump Hub - For tractor models 8N, 9N, 2N. Hydraulic Pump Hub is 3 inches outside diameter, 2 13/32 inches center to center on pins (no holes). Includes pins. (Item #: 112191, Ref: 191196) $32.00

Hydraulic Pump Hub - Hydraulic Pump Hub is used on tractor models 8N, 9N, 2N. Verify measurements. Hydraulic Pump Hub is 3 3/8 inches outside diameter, 2 3/8 inches center to center on holes. 6 spline - center bore = 5/8 inch on the lands and 3/4 inch on the grooves. Used with part numbers 192160 and 194354. (Item #: 111173, Ref: 192161) $45.10

Hydraulic Pump Overhaul Kit - For 8N, 9N, 2N (1939-52). Kit contains cam blocks, pistons, chamber kits, PTO shaft bushing, safety valve, and gaskets. (Item #: 118572, Ref: HPOK1) $165.20

Hydraulic Pump Rebuild Kit, Comprehensive - For tractor models 8N, 9N, 2N (1939 to 1952). Kit contains 2 cam blocks, 2 pistons, 2 chamber repair kits, PTO shaft bushing, safety valve, 2 valve chambers with valves, base gasket, sump pump gasket, 2 side gaskets, PTO shaft gasket, 2 side plate gaskets. Note, it may be necessary to grind the opening where the pump fits in some tractors. (Item #: 121926, Ref: S.61725) $316.00

Hydraulic Pump, Remanufactured, 9N605A - For Ford tractor models 2N, 9N, Replaces Ford OEM number 9N605A, To validate your warranty: A contaminated system should be completely flushed by an authorized dealer. Use new, clean fluid and filters, (Item #: 204643) $820.01

Hydraulic Pump Shaft for Loader - APPLICATION: 720 Loader. (Mates to end coupler L601-14 and End hub 290421). SHAFT DIAMETER: 3/4 ", SHAFT OVERALL LENGTH: 8-3/8 ", END A TYPE: Key, END A SIZE: 3/4 ", END B TYPE: 10 Spline, END B SIZE: 1 ". (Item #: 172481, Ref: 197118) $41.30

Hydraulic Pump Valve Chamber - Left Hand Valve Chamber, less valves. For 8N, 9N, 2N. (Item #: 170905, Ref: 9N622) $72.00

Hydraulic Pump Valve Chamber - Right Hand Valve Chamber, less valves. For tractor models 9N, 8N, 2N. Cast Iron.9N621-C (Item #: 170904, Ref: 9N621) $81.00

Hydraulic Pump Valve Chamber Assembly, LH - Left Hand Valve Chamber with valves. For tractor models 8N, 9N, 2N. Cast Iron. (Item #: 179000, Ref: 9N622-ASSY) $160.72

Hydraulic Pump Valve Chamber Assembly, RH - Right Hand Valve Chamber with valves. For tractor models 9N, 8N, 2N. (Item #: 186797, Ref: 9N621-ASSY) $95.00

Hydraulic Safety Valve Assembly - For tractor models 8N, 9N, 2N. Mounts on the hydraulic pump on 2N, 8N, 9N. **Note: The part you receive may look different than pictured, but will fit and work the same. Replaces: 8N638. (Item #: 113392, Ref: 8N638) $16.98

Hydraulic Spring Seat - For tractor models 8N, 9N, 2N, NAA, 600, 900 (1948-1954). Also replaces 181083M1 and 181098M1. (Item #: 182473, Ref: 9N525B) $17.20

Hydraulic Valve Assembly - This version does NOT have a slot in the round end. For (9N with 9N600 Pump Assembly), (2N with 9N600 Pump Assembly 1939-1947). Hydraulic Valve Assembly includes housing, pintle, spring, pin clip, fully assembled. (Item #: 110908, Ref: 9N640) $18.50

Hydraulic Valve Spring, Intake - Hydraulic Intake Valve Spring is goes between the pump control valve and the bushing. Ford 1939-1952. It replaces original part number 8N697 (Item #: 183685, Ref: 8N697) $5.60

Lift Cover Gasket - This Lift Cover Gasket is used on Ford 9N, 2N, 8N, NAA and Jubilee Tractors. Replaces NAA502A (Item #: 112063, Ref: NAA502A) $3.10

Lift Cover Repair Kit with Cylinder and Piston - This kit contains LCRK928 plus 9N510D Cylinder and NAA530B Piston. Includes Ring and Backing washer for Piston. Ford 9N, 2N, 8N (Item #: 182980, Ref: LCRK928WCP) $115.00

Lift Cylinder Housing Gasket - For tractor models 8N, 9N, 2N. (Item #: 179718, Ref: 9N553) $1.00

Lift Piston - This is a single groove Hydraulic Lift Piston that measures 2-1/2 inches in diameter, groove is centered 1 1/4 inch from bottom of piston. O-Ring available as NAA533A and back up washer as NAA473A. For tractor models NAA, NAB, 8N, 9N, 2N, Jubilee. (Item #: 116069, Ref: NAA530B) $25.70

Lift Piston - 3 Ring Piston, Hydraulic Lift. For 8N, 9N, 2N. Uses 9N675 ring set. (Item #: 150691, Ref: 9N530B) $22.60

$Ford 9N Lift Piston - 2-1\2 inch O-Ring Kit$
Lift Piston - 2-1/2 " O-Ring Kit - For Ford tractor models NAA, 2N, 8N, 9N Replaces Ford OEM number NAA473A, 44R330, , Compatible with Massey Ferguson tractor models F40, TE20, TEA20, TO20, TO30, TO35 (s/n 179304-earlier) Replaces Massey Ferguson OEM number 44R330, , Compatible with Massey Harris tractor models 50, Contains O-Ring 44R330 (116071), Backup Ring NAA473A (112216), For Lft Piston use Item #: 116069, (Item #: 116293) $10.50

Lock Washer, Assembly - Lock Washer Assembly for hydraulic lift shaft to arm. For tractor models 9N, 8N, NAA (1939-1954). (Item #: 179246, Ref: 9N550) $5.60

Pin, Hydraulic Lift Rocker - Lift Rocker Pin to Rear End Housing. 3/4 inch x 3.14 inch. For tractor models 9N, 2N (1939-1947). (Item #: 179528, Ref: 352625S8) $5.80

Piston for Hydraulic Pump - For 8N, 9N, 2N (1939-52). (Item #: 170925, Ref: 9N615) $26.30

Plate Hydraulic lift Control - Friction plate for hydraulic lift lever control. Use with disc C5NN518B. For 2000, 2N, 4000, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 9N, Jubilee, NAA 2N516B. Uses friction disc C5NN518B found on our web page. Bolt holes are 1/4 x 20. (Item #: 111910, Ref: 9N515) $29.90

Quadrant Stop Kit - For tractor models 2000 4 Cylinder, 2N, 4000 4 Cylinder, 8N, 9N, Jubilee, NAA, NAB, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 1801, 1811, 1821, 1841, 1871, 1881, 2030, 2031 all with 4 Cylinder from 1939 to 1964. (Item #: 126615, Ref: 9N521) $8.10

No
Picture
Shaft, Splined - Shaft, Pump Drive For 8N, 9N, 2N (Item #: 111595, Ref: 94354) $31.90

Superior and Wagner Loader Hydraulic Pump Kit - Hydraulic Pump Kit for various loaders mounted on Ford tractors. Pump specifications: 14 GPM at 2000 RPM, 3/4 inch round shaft with key, left hand rotation, inlet port 1 inch NPT, outlet port 3/4 inch NPT. Kit includes hydraulic pump, foot/flange bracket, 2 mounting bolts and washers, and 2 adapters. Replaces 3660. (Item #: 178897, Ref: L827-10X) $1039.01

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.60

Valve chamber to base Gasket - For tractor models 8N, 9N, 2N (1939-1942). (Item #: 179720, Ref: 9N613) $2.30

Implements

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $120.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.70

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00

Lights

Bracket - Headlight bracket reinforcement, clear zinc plated for WINGED headlight bracket. For tractors: 9N, 2N, 8N {1939-1949}. (Item #: 126628, Ref: 9N13102) $11.00

Bracket Set For Lights - SEE PART NUMBER 9N13471 Fits rounded fenders. For tractor models 8N, 9N, 2N, NAA, Jubilee. Replaces: 9N13470, 9N13471 (Item #: 125324, Ref: 1750673M1) $54.00

Headlight, 12 Volt - 12 Volt, 5-3/4 inch diameter, sealed beam bulb. Fits 8N, 9N, 2N, Complete assembly is a copy of original headlight, IS NOT EXACTLY LIKE ORIGINAL. Single unit Replaces 13005C or 13006C assemblies (right hand or left hand). (Item #: 183739, Ref: S.66419) $57.00

Headlight, 12 Volt Chrome Ring - This headlight assembly is Complete with sealed beam bulb with steel socket, Chrome ring, Stamped TRACT-O-LITE in housing. Replaces 2N13006C, 2N13005C. (Item #: 187042, Ref: S.67893) $68.00

Headlight, 6 Volt Chrome Ring - This headlight assembly is Complete with sealed beam bulb with steel socket, Chrome ring, Stamped TRACT-O-LITE in housing. Replaces right or left side OEM part numbers 2N13006C and 2N13005C. (Item #: 187043, Ref: S.67892) $161.00

Headlight, 6 Volt, RH or LH - Headlight for 8N, 9N, 2N, Complete assembly is a copy of original headlight. NOT EXACTLY LIKE ORIGINAL. Replaces 2N13005C and 2N13006C. (Item #: 113349, Ref: 2N13005C) $57.00

Headlight Bracket, Winged Left - Winged Headlight Bracket for left side. For tractor models 8N, 9N, 2N, NAA. (Item #: 111699, Ref: 9N13473) $22.40

Headlight Bracket, Winged, Right - Headlight Winged Bracket for the right side. For tractor models 8N, 9N, 2N, NAA. (Item #: 111600, Ref: 9N13472) $20.70

Headlight Clip Set, Pack of 7 - Clip, headlight wiring to hood. Set of 7. For tractors: 8N, 9N, 2N {1939-1952}. Replaces OEM part number 358297S32. 7 Required per tractor. (Item #: 178037, Ref: 358297S7) $4.70

Headlight Reinforcement Plate - Fits Ford tractors from 1939 and up. (Item #: 111329, Ref: FAA13102A) $5.60

Headlight Set, 12 Volt - This Headlight is exactly like the factory original with TRACT-O-LITE stamped into housing for tractor models 1939-1954. Will also fit models through 1964 but are not the same diameter as originals. For tractor models 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, 2000, 4000, 8N, 9N, 2N, NAA 1939-1964. This is a pair of headlight assemblies complete with sealed beam bulb. (Item #: 183740, Ref: 2N13005-12V) $159.00

Headlight Set - 6 Volt - This Headlight is exactly like the factory original with TRACT-O-LITE stamped into housing for tractor models 1939-1954. Will also fit models through 1964 but are not the same diameter as originals. For tractor models 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, 2000, 4000, 8N, 9N, 2N, NAA 1939-1964. This is a pair of headlight assemblies complete with sealed beam bulb. Replacement sealed beam bulbs available as p/n L4019. (Item #: 183751, Ref: 2N13005-6V) $152.00

Knob, Light Switch - Aluminum. For tractor models 8N, 9N, 2N, NAA, Jubilee, 501, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 750, 771, 801, 811, 820, 821, 840, 841, 850, 851, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 4000. 10-32 thread. (Item #: 178058, Ref: 9N9703) $5.40

Light Rim - Headlight Door Assembly {rim}. For tractors with TRACT-O-LIGHT stamped lights only. For tractors: 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900 {1939-1956}. This rim is 3/4 inch in width. (Item #: 178057, Ref: 2N13043) $21.60

No
Picture
Light Rim CHROME - For tractors with TRACT-O-LIGHT stamped lights only. For tractors: 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900 {1939-1956}. Replaces 2N13043. (Item #: 184649, Ref: S.67891) $22.60

Light Switch - For tractor models 8N, 9N, 2N, NAA, Jubilee. Light Switch with fuse. (Item #: 112512, Ref: 8N11654B) $10.10

Sealed Beam Bulb, 6 Inch - The Sealed Beam Bulb is 6 Volt, 5.625 inches in diameter and has two contacts. Fits models: NAA, 2N, 8N, 9N, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000. It replaces Ford part number 310061. (Item #: 111244, Ref: 1002802M91) $18.90

Switch, Headlight - Assembly with pigtail wire connectors. This is an EXACT reproduction of the ORIGINAL headlamp switch. For tractor models 8N, 9N, 2N (1939-1949). (Item #: 121152, Ref: 9N11652) $13.00

Tail Light Assembly - This is a restoration quality Taurus Taillight Assembly. 1939-47 9N, 2N. It comes grey Powder Coated, rim and bucket. Includes 6V bulb, wiring and mounting studs and nuts. Includes small moisture drain hole which was a later year improvement. Replaces 9N13404 (Item #: 184023, Ref: 9N13404) $63.00

Tail Light Assembly - This is a restoration quality Taurus Taillight Assembly. It comes grey Powder Coated, bucket and polished stainless steel rim. Includes 6V bulb, wiring and mounting studs and nuts. Includes small moisture drain hole which was a later year improvement. Replaces 9N13404 (Item #: 183689, Ref: 9N13404SS) $63.00

Tail Light Assembly, 6 Volt - Exact as Original in Every Detail. Ford Duolamp (stamped in tailight housing) tractors: 8N, 9N, 2N (1939-1952). If Using in a 12 Volt system order 12 volt bulb part number TLBULB12V and replace. (Item #: 126632, Ref: 8N13404) $77.00

Tail Light Bezel - This Taillight Bezel is used on Taurus Taillights 9N13404 and 9n13404SS. It is zinc plated steel. It replaces 9N13448 (Item #: 179632, Ref: 9N13448) $4.98

Tail Light Bezel - This Taillight Bezel is used on Taurus Taillights 9N13404, 9n13404SS, 1751422M91 and 1750667M91. It is polished stainless steel. It replaces 9N13448 (Item #: 191183, Ref: 9N13448SS) $15.10

$Ford 9N Tail Light \ Dash Light Bulb - 12-Volt$
Tail Light / Dash Light Bulb - 12-Volt - This 12 Volt Bulb is a Single contact with a Bayonet base. It is 0.59 amps. The base diameter is 0.595 inches. It is used in many tail lights and dash lights. May be used when changing from 6 - 12 Volts. (Item #: 150699, Ref: TLBULB12V) $0.50

Tail Light Fender Bracket Pair - These Tail Light Fender Brackets come as a pair. One left and one right for tractor models 8N, 9N, 2N (1939-1952). Replaces: 9N13470, 9N13471. Sheet metal / body parts need to be sanded and painted to match your tractor. (Item #: 125324, Ref: 9N13471) $54.00

Tail Light Lens - This Lens is used with 9N13404, 9N13404SS, 1750662M91 and 1751422M91 Taurus Taillights. It replaces 9N13450. (Item #: 183015, Ref: 9N13450) $14.40

Tail Light Lens Gasket - This Lens Gasket is used with 9N13404, 9N13404SS, 1750662M91 and 1751422M91 Taurus Taillights. It replaces 9N13460 (Item #: 183014, Ref: 9N13460) $2.98

Tail Light License Lens Gasket - This Lens Gasket is used with 9N13404, 9N13404SS, 1750662M91 and 1751422M91 Taurus Taillights. It replaces 9N13447 (Item #: 183013, Ref: 9N13447) $1.98

Taillight Mounting Bracket - Exact of original. Manufactured in USA. For tractors with Taurus Tail Light: 9N, 2N (1939-1948). (Item #: 179554, Ref: 9N13423) $13.70

Taillight Mounting Bracket - Exact of original. Manufactured in USA. (goes between tail light and fender bracket, mounting on top of 9N13470 or 9N13471.) For DUOLAMP tractors 8N, 9N, 2N, NAA, Jubilee, 501, 600, 601, 700, 701, 800, 801, 900, 901, (2000, 4000 4-cylinder), 1801 series (1949 to 1954). (Item #: 125325, Ref: 8N13423) $10.00

Tail Light Wire Clip - For 8N, 9N, 2N, NAA and Jubilee to 1954. Rear lamp wire clip. 6 required per tractor. (Item #: 178041, Ref: 9N17668) $3.40

Tail Lite, License Light, Clear Glass Lens - This Tail Lite is used with 'Taurus' style tail lights, originally used 1939-1947. It may be found on later tractors if a Taurus lamp was used. Uses Gasket FAA13447A, not included. (Item #: 183031, Ref: 9N13445) $12.20

Tail Lite, License Light, Lens Gasket - For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881 all 1939-1953. Replaces 40-13460, FAA13447A (Item #: 178109, Ref: FAA13447A) $4.50

Worklight Kit, 6 Volt, Chrome - Kit includes, 6 inch steel body, chrome ring, sealed beam bulb, bulb retaining clips, steel worklight mount (socket), and switch. Assembly required. For tractor models 8N, 9N, 2N, NAA, 600, 800. (Item #: 180003, Ref: S.43377) $92.00

Worklight Mounting Socket - Fender bracket round spacer, worklight to fender bracket {included with work-light assemblies}. For Ford tractors: thru 1958 (Item #: 178566, Ref: 8N15532) $14.70

Miscellaneous

Historical Tractor Photographs - These beautiful black and white photo reproductions are of 9N, 2N and 8N Ford tractors. Set of 16 photos (12 inches x 18 inches). These are good semi-glossy prints suitable for framing. Great for the shop or as a gift! (Item #: S.22994) $96.43

No
Picture
Rubber Grommet - For Ford tractor model 9N, Replaces Ford OEM number 190753, (Item #: 173694) $1.30

Tractor Cover - Tractor Cover Fits 8N, 9N, 2N. Rugged synthetic material. Color varies. No Logos. (Item #: 178964, Ref: S.60175) $233.00

Oil System

Engine Oil Dipstick - For tractor models 8N, 9N, 2N. (Item #: 124338, Ref: B2NN6750A) $6.20

Gasket, Oil Pan Drain Plug - Fits Ford Tractors 1939 to 1964, Models: NAA, NAB, Jubilee, 2N, 8N, 9N, 501, 600, 601, 700, 701, 800, 801, 900, 901, 1801, 2000, 4000. This gasket measures 2.632 inches inside diameter, 3.085 inches outside diameter, .250 inches wide and it is .059 inches thick. Replaces 8N6734. (Item #: 110499, Ref: 8N6734) $1.70

Oil Filler & Breather Cap - Oil filler and breather cap. Economy style for a pipe with a diameter of 1-1/2". OEM 8N6766B. Compatible with Ford Tractor(s) NAA, 2N, 8N, 9N, 501, 540, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 761, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2031, 2111, 2131, 4000, 4030, 4031, 4110, 4120, 4121, 4130, 4131, 4140 (Item #: 113708) $4.98

Oil Filler Breather Element - Fits caps 310030 and 8N6766B. For tractor models 8N, 9N, 2N, NAA, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000, 2030, 2031, 2111, 2131, 4000, 4030, 4031, 4040, 4110, 4120, 4121, 4130, 4131, 4140. (Item #: 189611, Ref: 8N6782A) $6.90

Oil Filler Cap - Oil Filler Breather Cap. For tractors: 8N, 9N, 2N (1939-1950). Overall length is 3 5/8 inches, 1 1/4 inch diameter tube and tube is 1 3/8 inches long. (Item #: 125660, Ref: 9N6766) $31.70

Oil Filler Cap with Element - Oil filler cap measures 3 1/2 inches diameter. Insert is 1 1/4 inches outside diameter. For tractor models 8N, 9N, 2N, NAA, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000, 2030, 2031, 2111, 2131, 4000, 4030, 4031, 4040, 4110, 4120, 4121, 4130, 4131, 4140. This is an original style with element. Overall length is 3 5/8 inches, 1 1/2 inch diameter tube and tube is 1 3/8 inches long. Also replaces OEM 8N6766B. (Item #: 121246, Ref: 310030) $10.00

Oil Filter - Oil Filter with gasket measures 4 inches in length and 3 11/16 inches in diameter. For tractors: 8N, 9N, 2N (1939-1952), 340. For Balers: 166, 271, 272, 273, 283, 286. (Item #: 111097, Ref: APN6731B) $9.50

Oil Filter Outlet To Block Line - This Oil Filter Outlet to block line is used on Ford 9N and 2N Tractors, 1939 to 1947 with Cast Iron Governor. Replaces 9N18666. (Item #: 183019, Ref: 9N18666) $13.80

Oil Filter To Junction Block Line - This Oil Filter to junction block line is pre-bent steel. It is used in Ford 9N and 2N, 1939 to 1947. It replaces original part number 9N18667. (Item #: 183020, Ref: 9N18667) $18.80

Oil Pan Plug Kit - Gasket, Oil Pan Plug and Screen Assembly. For all gas models 1939-1964. Fits 8N, 9N, 2N, NAA, Jubilee, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000. (Item #: 108080, Ref: 9N6730WG) $20.50

Oil Pick Up Tube - This Oil Pick Up Tube comes as pictured for tractor models 8N, 9N, 2N. Part does not come with gasket. Gasket can be ordered separately as part number 9N6619. Replaces: 86604201, 8N6615, 9N6615. (Item #: 111026, Ref: 8N6615) $42.00

Oil Pump Body - For tractor models 9N, 2N, 8N to serial number 247571. For pumps with 9/16 inch gear width. Pump body assembly does not include gears. (Item #: 178723, Ref: 9N6603) $181.00

Oil Pump Bushing - Fits 8N, 9N, 2N. (Item #: 112119, Ref: 9N6612A) $6.90

Oil Pump Cover Gasket - For 8N, 9N, 2N. Replaces 9N6619 (Item #: 173015, Ref: 9N6619) $2.00

Oil Pump Gear - Gear, oil pump driven, width 9/16 inch. For tractor models 8N, 9N, 2N. (Item #: 179207, Ref: 52-6610B) $65.00

Oil Pump Gear - Gear, oil pump drive, width 9/16 inch. For tractor models 8N, 9N, 2N. (Item #: 179207, Ref: 52-6614B) $65.00

Oil Pump Gear - For 8N, 9N, 2N. Oil pump large gear with 1 1/2 inch shaft for oil pump body number 9N6603. (Item #: 172596, Ref: 9N6608A) $35.80

Oil Pump Kit - Complete Oil Pump Repair Kit. For Ford 8N, 9N, 2N prior to serial number 247570 (1939-1948). For pumps with 9/16 inch gear WIDTH. Early and late pumps are interchangeable, so measure small gear width before ordering. (Item #: 117376, Ref: APN6600A) $83.44

Oil Pump Relief Plunger Spring - Oil Pump Relief Plunger Spring. For tractor models 8N, 9N, 2N (1939 to 1952). Replaces 9N6608A, 9N6654, APN6600A (Item #: 178166, Ref: 9N6654) $3.30

Oil Pump Repair Kit - For Ford tractor models 2N, 8N, 9N, Compatible with Ford Engine (s) 120, Replaces Ford OEM number APN6600B, Set of 2 3/4" Gears, Bushing, Gasket, (Item #: 165753) $105.97

$Ford 9N Oil Pump Repair Kit - w\o Main Gear$
Oil Pump Repair Kit - w/o Main Gear - For Ford tractor models 2N (1/42-12/47), 8N (1/47-12/52), 9N (1/39-12/41), Replaces Ford OEM number APN6600A, For oil pumps with 0.5625" (9/16") wide gears, Main drive gear not included, Oil Pump Repair Kit - W/Drive gear use Item #: 117376, (Item #: 109977) $51.00

Oil Relief Valve Inlet Gasket - For tractor models 8N, 9N, 2N. (Item #: 172747, Ref: 1GA6669) $0.90

Oil Terminal Block - For tractor models 9N, 2N from 1939-1947. (Item #: 179495, Ref: 9N6722) $9.90

Plunger - Plunger, Oil Pump Relief Valve. For tractors: 8N, 9N, 2N, (1939 to 1952). The spring is available separately as 9N6654. (Item #: 168906, Ref: 01A6663) $18.50

Paint

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40

No
Picture
Paint, Dark Gray, 1 Gallon - For tractors: 9N, 2N (1939 to 1947). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108333, Ref: TP2888GAL) $55.00

No
Picture
Paint, Dark Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.For 2N and 9N (1939-1947). Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108332, Ref: TPM2888LF-QT) $23.40

No
Picture
Paint, Dark Gray, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Fords (1939-1947). Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108332, Ref: TP2888QT) $23.40

No
Picture
Paint, Dark Gray, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Fords (1939-1947). Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108331, Ref: TP2888SP) $7.50

No
Picture
Paint, Ford White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108135, Ref: TP470GAL) $82.00

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $60.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30

PTO / Driveline

Bearing, PTO Shaft - This PTO Shaft Bearing is for the original 1 1/8 inch shaft, measures 2 7/16 inches outside diameter, 1 3/16 inch inside diameter, 5/8 inch width. For 8N, 9N, 2N, NAA (1953-1954), Jubilee, NAB, 600 thru 1956. Replaces 9N715C. Also used as a PTO Shifter Support Housing Bearing with 3 and 4 speed transmissions. Used as an upper PTO Countershaft Bearing on 1300, 1310, 1320, 1500, 1510, 1520, 1600, 1620, 1630, 1710, 1715, 1725, 1925 Replaces 210064, 9N715B, 9N715BC, 9N715C, SBA040106206 (Item #: 180397, Ref: 9N715BC) $6.10

PTO Cap - Fits most Ford Tractors 1939 and later. Replaces part numbers 81809440, 310088, 80310088, 310088F, 0310088F (Item #: 109510, Ref: 310088) $7.80

PTO Cap - This PTO Cap is for 1-1/8 or 1-3/8 inch PTO shafts. Like original. 3 1/2 inches in length. Inside usable length is 2 7/8 inches. Replaces 2N726, NCA726A, 2N726, NCA726A (Item #: 125614, Ref: 2N726) $9.30

PTO Cap - Short - For Ford tractor models NAA, 2N, 8N, 9N, 501, 541, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 2031, 2100, 2110, 2111, 2120, 2131, 2150, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3600, 3610, 3910, 4000, 4031, 4100, 4110, 4120, 4121, 4131, 4140, 4190, 4200, 4330, 4340, 4400, 4410, Compatible with Ford Construction and industrial models 1801, 1811, 1821, 1841, 1871, 1881, 2030, 3500, 3550, 4040, 4140, 4500, Replaces Ford OEM number 310088F, (Item #: 155022) $9.40

No
Picture
PTO Collar with Pin - Collar with tapered pin fits models: 9N, NAA, Jubilee, 600, 800, 900 (Item #: 172548, Ref: NAA70038C) $18.40

PTO Housing Gasket - This PTO Housing Gasket is used on many Ford tractor models: Dexta, Super Dexta, NAA, 2N, 8N, 9N, 231, 233, 234, 333, 334, 335, 340, 340A, 340B, 420, 445A, 515, 530A, 531, 540A, 540B, 545A, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 2110LCG, 2310, 2600, 2610, 3000, 3400, 3500, 3550, 3600, 3610, 3910, 4000, 4400, 4500. Replaces: 81801907, 957E4129, 9N4129, C5NN747A. (Item #: 109986, Ref: C5NN747A) $1.00

PTO Shaft - PTO Shaft. For 8N, 9N, 2N (converts 1 1/8 inch shaft to 1 3/8 inch spline. This is the shaft only. (Item #: 186970, Ref: 9N710-38) $67.00

$Ford 9N PTO Shaft Assembly 1-1\8 inch shaft$
PTO Shaft Assembly 1-1/8 inch shaft - This assembly has the original 1-1/8 inch 6 spline output shaft. If you need a 1-3/8 shaft, use part number 109422. Replaces 9N700-18, 9N70018 (Item #: 134460) $59.98

PTO Shaft Bearing, Front - For tractor models: Dexta, Super Dexta, NAA, Jubilee, 501, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 2110LCG, 2310, 2600, 2610, 2810, 2910, 3000, 3400, 3500, 3550, 3600, 3610, 3910, 3900, 4000, 4100, 4110, 4110LCG, 4400, 4500, 4600, 4610, 5000, 5600, 5610, 5610S, 5900, 6600, 6610, 6610S, 6700, 6710, 6810, 7600, 7610, 7610S, 7700, 7710, 7810S, 8010. All WITH 1 3/8 Inch DIAMETER PTO SHAFT. WILL NOT FIT 1 1/8 Inch DIAMETER PTO SHAFT. Replaces 81800755, C5NN7118A, 20705250, E75GE9 (Item #: 178129, Ref: E75GE9) $7.00

PTO Shaft Conversion Assembly - Shaft Assembly converts 1-1/8 inch PTO system to 1-3/8 inch. Assembled and ready to install by removing 4 bolts from cover. Length 30-7/8 inches. Uses gasket C5NN747A and cap 310088 (not included). (Item #: 109422, Ref: 9N700-38) $83.00

PTO Shaft Housing - This PTO Shaft Housing is for models 8N, 9N, 2N, (NAA 1953-1954), Jubilee, NAB. (Item #: 179673, Ref: 9N733B) $36.10

PTO Shaft Seal - PTO Shaft Seal. For 8N, 9N, 2N, NAA. Replaces OEM numbers D8NN703AA and 9N703B. (Item #: 111314, Ref: D9NN703BB) $4.00

PTO Shaft Seal, Double Lip - For All Models: 1939 thru 1964 with 1-1/8 inch or 1-3/8 inch PTO shaft. 2.45 inch outside diameter, 1 5/8 inch inside diameter, 5/8 inches wide. Replaces OEM numbers : D8NN703AA and D9NN703BA, and 9N703B. (Item #: 111314, Ref: D9NN703BB) $4.00

$Ford 9N PTO Shaft Sleeve Bushing, 1-1\8$
PTO Shaft Sleeve Bushing, 1-1/8 - For 1-1/8 inch PTO Shafts (NOT 1-3/8 inch) 1.113 inch inside diameter, 1.620 inch outside diameter, 1 inch thick. For tractor models 9N, NAA (1953 to 1954), 2N, 8N, NAB, 600, 700, 800, 900. (Item #: 158215, Ref: 9N735B) $7.70

$Ford 9N PTO Shaft Sleeve Bushing, 1-3\8$
PTO Shaft Sleeve Bushing, 1-3/8 - For 1-3/8 inch PTO Shafts, 1.185 inch inside diameter, 1.620 inch outside diameter. For tractor models 9N, NAA (1953-54), 2N, 8N, NAB, 600, 700, 800, 900. all with 1-3/8 inch PTO shaft. (Item #: 173070, Ref: 9N73538) $6.90

PTO, Snap Ring - For tractor models 8N, 9N, 2N, NAA all 1943-1954. 2.58 inches outside diameter, 2.26 inches inside diameter. (Item #: 165401, Ref: 9N754) $4.30

PTO Stop - This PTO Stop is used on 3, 4 and 5 speed transmissions. 8N, 9N, 2N, NAA, 500, 600, 700, 800, 900, 501, 601, 701, 801, 901, 2000-4000 4 CYLINDER, 2000, 3000, 3400. (Item #: 113727, Ref: NAA722A) $20.20

Seats

Pan Seat - This 19 inch wide Fixed Seat For 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 800, 2000, 4000, all with 4 Cylinder Engine. This is not a Flip-Over Seat. The color of paint varies and will not match your tractor paint. You will need to repaint it to match your tractor. (Item #: 101352, Ref: 8N400) $50.00

Pan Seat - 19 inch wide Flip-Over Style. Replaces OEM number C5NN400AE. Seat only - does not include spring or bracket. For NAA, Jubilee, 600, 800, 2000, 4000, 8N, 9N, 2N (4-Cylinder). May come different color than pictured. (Item #: 101239, Ref: C5NN400AE) $60.00

Seat Cushion, Blue - For all Ford Tractors with 19 inch wide Steel Pan Seat. This seat cushion is blue with a FORD script logo. (Item #: 178635, Ref: 9N401B) $48.20

Seat Cushion (Blue and White) - For all Ford Tractors with 21 inch wide Steel Pan Seat. This seat cushion is blue and white with a FORD script logo. (Item #: 179048, Ref: R4120) $44.30

Seat Cushion (Red) - For all Ford Tractors with 19 inch wide Steel Pan Seat. This seat cushion is red with a FORD script logo. (Item #: 178636, Ref: 8N401R) $48.20

Seat Cushion (Red and White) - Seat Cushion. Deluxe with 2 inches of foam padding. For all Ford Tractors with 19 inch wide Steel Pan Seat. This seat cushion is red and white with a FORD script logo. (Item #: 180739, Ref: R4118) $28.70

Seat Spring - Fits 9N, 2N (AI) (Item #: 101242, Ref: 9N404) $57.00

Seat Spring - For 9N, 2N (Item #: 126069, Ref: R0644) $53.00

No
Picture
Seat Spring, Non-Flip, Used - For Ford tractor models NAA, 2N, 8N, 9N, 600, 800, 2000, Replaces Ford OEM number 9N404, Flat Spring, For Non Flip Seat, For a new version of this item use Item #: 101242, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435282) $34.80

No
Picture
Tie-On Seat Cover - Tie-On Seat Cover. 19 inch Tie-On Cover with White Script Ford Logo. Fits models: NAA, 2N, 8N, 9N, 600, 620, 630, 640, 650, 660, 800, 820, 840, 850, 2000, 4000. (Item #: 178809, Ref: R4117) $36.30

Sheet Metal / Body Parts

Air Cleaner Door - Air Cleaner Door with fastener. COMES PRIMERED, NOT PAINTED. For Air Cleaner opening in hood. For tractor 8N (1948-1952). Also for 9N and 2N when replacing hood with 8N16612. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 110905, Ref: 8N9661) $11.00

Battery Cover, Snap In - This snap in place Battery Cover installs under the Hood Door and prevents fuel from spilling onto the battery. This part comes Zinc Plated and ready for paint. Used on Ford 9N and 2N tractors, 1939-1947. It Replaces original part number 9N10737. (Item #: 183027, Ref: 9N10737) $37.30

Battery Door - For 8N, 9N, 2N. Battery Door. Includes handle, hinge and latch. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 110288, Ref: 9N16938C) $39.10

Battery Door Handle Kit - Contains Battery Door Latch with Handle and Stud. For tractor models 9N, 8N, 2N. (Item #: 112065, Ref: 9N16625-56) $16.40

Battery Door Hinge Kit - For tractor models 8N, 9N, 2N. Contains Hinge for Battery Door. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 179088, Ref: 9N16651-89) $23.80

Battery Door Latch Kit, Black - Door Latch and Handle with stud. For tractor models 8N, 9N, 2N. Includes nut. (Item #: 180761, Ref: 9N16625B) $16.40

Battery Door Latch Kit, Chrome - Door Latch and Handle with stud. For tractor models 8N, 9N, 2N. (Item #: 115847, Ref: 9N16625C) $15.30

Battery Hold Down - (Must use 01A10726 rubber insulator with this part). For tractor models 9N, 2N (1939 to 1942). (Item #: 178035, Ref: 9N10724) $23.80

Battery Hold Down, Left Side - For model 9N (1943 to 1947). Ford improved design, originally sold in the mid 1940s. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 191179, Ref: 9N10748) $17.00

Battery Hold-Down Retainer - For 9N, 2N, (1939-1947). Ford improved design was originally sold in the mid 1940s. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 126474, Ref: 2N10721) $40.00

Battery Hold Down, Right Side - For model 9N (1943 to 1947). Ford improved design, originally sold in the mid 1940s. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 183750, Ref: 9N10728C) $21.52

Battery Hold Down Strap - Fits 9N10724 (goes through the cast dash). For 9N, 2N early, (1939 to 1942). Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 183745, Ref: 9N10728B) $14.90

No
Picture
Bumper - For Ford tractor models 2N, 8N, 9N, Replaces OEM number 311541HD, Comes primered (color may vary). Prior to painting check fitment, Additional Handling and Oversize Fees Apply To This Item, (Item #: 146704) $134.00

Bumper Bolt Kit 4 Pieces - Bumper Bolt kit, front axle bolt kit, contains 2-3.40 inch bolts, 2-4 inch bolts, 4-351505S8 washers and hex nuts. For tractors: 8N, 9N, 2N, NAA, 600, 800 {1939-1957}. For 600, 700, 800, 900, NAA. (Item #: 178018, Ref: 350790-KIT) $16.60

Bumper - Heavy Duty - For 8N, 9N, 2N, NAA, Jubilee, 600, 800, 2000, (4000SU with I-Beam Front Bumper). Additional $15 shipping due to weight. Welded, not riveted. Slightly different than original. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 104060, Ref: 311541HD) $225.31

Bumper, OEM Quality - Front Bumper Assembly with four bars for extra protection. Fits 8N, 9N, 2N. Made to take rugged service. Welded and riveted construction. Exact copy of the original OEM bumper. 24-1/2 inches center to center mounting bolt holes. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 182834, Ref: 311541OE) $294.00

Bumpers 4 Per PKG - Rubber Bumpers for Gas Filler Lid Door {set of 4}. For tractors: 8N, 9N, 2N {1939-1952}. (Item #: 126647, Ref: 11A16758A) $21.90

Fender - For tractor models 8N, 9N, 2N, NAA, Jubilee. Rear Fender, dished type, with mounting bracket. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. These are sold individually. (Item #: 104069, Ref: 8N16312) $104.00

Fender - Fender Panel (no longer supplied by OEM). Price is for 1 panel. Panel comes primed. To install, remove fasteners from old panel, drill new holes and bolt new panel in place. Panel, less mounting brackets. For 8N, 9N, 2N (1939 to 1952) and row crop high clearance models 700 and 900 (1957-1962), fits right side or left side. (Item #: 100026, Ref: 526904M1) $105.00

Fender Bolt Kit - For Ford tractor models NAA (when not equipped with sway bar brackets or loader brackets), 2N, 8N, 9N, 501, 540, 541, 600, 601, 700, 701, 800, 801, 900, 901, 2000 (4 cylinder), 2031, 2110, 2111, 2120, 2130, 2131, 4000 (4 cylinder), 4030, 4031, 4110, 4120, 4121, 4130, 4131, 4140, Compatible with Ford Construction and industrial models 1801, 1811, 1821, 1841, 1871, 1881, 2030, Compatible with Massey Ferguson tractor models TE20, TEA20, TO20, TO30, TO35, 20, 30, 35, 40, 50 (when not equipped with sway bar brackets or loader brackets), 65, 135, 150, 230, 240, 245, Compatible with Massey Ferguson Construction and industrial models 20, 30, 50 (when not equipped with sway bar brackets or loader brackets), 65, 202, 203, 204, 205, 2135, 2200, Compatible with Massey Harris tractor models 50 (when not equipped with sway bar brackets or loader brackets), Compatible with Oliver tractor models Super 55, 550 (when not equipped with sway bar brackets or loader brackets), Compatible with White tractor models 2-44 (when not equipped with sway bar brackets or loader brackets), Replaces OEM number 353648X14, 364918X14, 375651S8, 3541315S36, 372457S36, 900157, Kit includes 4 (6-1/2") carriage bolts (5/8" NC), nuts, lock washers, Use with fenders 100026, 104069, 104070, 104072, 125421, For OEM Quality use Item #: 183747, (Item #: 154411) $37.00

Fender Skin, No Script - Fender Skin, without script. Price is for one fender. For tractor models 2N, 8N, 9N, Jubilee, NAA.Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Replaces: C0NN16312A. (Item #: 100026, Ref: 526904M1) $105.00

Fender With FORD Script - This Fender Panel has the raised "FORD" script. Panel comes primed. To install, remove fasteners from old panel and bolt new panel in place. Panel can be shipped UPS. Panel, less mounting brackets. For 8N, 9N, 2N, 700, 900, NAA, Jubilee (1939 to 1954), fits right side or left side. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Replaces: 8N16312C (Item #: 185187, Ref: FF101S) $235.00

No
Picture
Front Grill - For 8N, 9N (Item #: 112514, Ref: R0095) $56.00

Grill - Aftermarket version of grill. For 8N (1948-1952). Will fit 2N and 9N with modification - remove brackets from old grill and apply to new grill. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 112514, Ref: 8N8204) $56.00

Grill - Radiator Grill Assembly, with TEAR DROP Grill Bars. For tractors: 9N, 2N. Manufactured to restoration standards. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. This item will ship directly from manufacturer and may take up to 4 weeks for delivery. (Item #: 126634, Ref: 9N8206D) $349.97

Grille - Radiator Grille Assembly, with ROUND Grille Bars. For tractors: 9N {early 1941}. Manufactured to restoration standards. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 182876, Ref: 9N8206C) $416.00

Grill Screen, Ferguson System, Blue - Fits 9N, 2N. Replaces 9N-8210. Complete with fasteners. Exactly like the original. (Item #: 183043, Ref: 9N8210) $107.10

Hood - Includes Battery Cover. For tractors 8N, 9N, 2N. When used on 9N and 2N also order Air Cleaner Door 8N9661. Replaces 8N16612, 9N16938C. This part does not have the raised Ford Script. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Additional $10.00 shipping due to size and weight. (Item #: 104051, Ref: 8N16612) $310.00

Hood Panel - Left Hand Hood Panel For 8N, 9N, 2N. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 104056, Ref: 8N16619) $54.98

Hood Panel Right - Right Hand Hood Panel For 8N, 9N, 2N. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Replaces 8N16618, 8N16618A, 8N16618FR (Item #: 104055, Ref: 8N16618A) $49.98

Insulator, Battery Hold Down Strap - Rubber insulator for 9N10724 battery hold down bar. Fits 9N, Early 2N (1939 to 1942). Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 179736, Ref: 01A10726) $1.98

License Plate Bracket - This License Plate Bracket is used with Taurus Style Tail Lights. Originally used 1939 to 1949. Replaces original part number 9N13406. (Item #: 183016, Ref: 9N13406) $7.80

License Plate Bracket - This License Plate Bracket is used on tractors with Duolamp Tail Lights. Used on Ford Tractor Models 9N, 2N, 8N, NAA and Jubilee, 1939-1954. (Item #: 183002, Ref: 8N13406) $12.50

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $178.00

Side Panel Bolt Kit - Bolts 2 per package, hood side panel to axle support bolt, nut and washer kit with dog point. This is an EXACT reproduction of the ORIGINAL side bolts. For tractors: 8N, 9N, 2N, {1939-1952}. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 178015, Ref: 350782-KIT) $7.20

Step Plate Bracket - For 9N, 2N. Step Plate Bracket (right or left) used on Step Plates #180717M91 and #191929M92. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 111624, Ref: S.42997) $14.40

Step Plate - Left - For 9N, 2N. Left Hand Step Plate. 24 inches in length. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 111165, Ref: 180717M91) $39.98

Step Plate - Right - For 9N, 2N. Step Plate - Right. 24 inches in length. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 111172, Ref: 191929M92) $46.10

Toolbox - This New Toolbox with Attached Mounting Bracket is used in tractors with cast dash and battery trays. Powder coated Gray. Comes with 2 bolts. Replaces 9N17005A, 1939 to 1942. Box measures 11 1/4 inches long, 4 3/8 inches deep and 5 inches tall. Mounting bolt holes are 4 1/4 inches center-to-center. This item will ship directly from manufacturer and may take up to 4 weeks for delivery. (Item #: 178940, Ref: 9N17005A) $49.40

Upper Side Panel Bolt Kit - For Ford tractor models 2N, 8N, 9N, Compatible with Massey Ferguson tractor models TE20, TEA20, TO20, TO30, TO35, 35, Replaces OEM number 34806S, 20311S7, 33798S, Includes 4 Fine Threaded Bolts, Nuts, Lock Washers, (Item #: 126764) $5.10

Steering

Axle Hardware Kit 4 PCS. - Bolt Kit, front axle bolt, nut and washer. Holds right and left axles to center axle. Bolts are 3 1/2 inches and 5/8x18. Nuts have 1 1/6 head. For tractors: 8N, 9N, 2N {1939-1952}. For 600, 700, 800, 900, NAA. (Item #: 178012, Ref: 350789-KIT) $16.60

Axle Pin Support Bushing - This Axle Pin Bushing for models 2N, 8N, 9N, 600, 700, 800, 900, 2000, 4000, NAA, Jubilee. Front Axle Bushing 1939-1964 with standard front axle. Bushing, front axles, 1.778 inch inside diameter, 1.913 inch outside diameter, 1.5 inch length (not for heavy, industrial or grove axles). (Item #: 110832, Ref: 2N3039) $7.70

Axle Washers 16 Per PKG - Flat washer kit, 5/8, rear wheels and front axle bolts. Set of 16. For tractors: {1939-1954}. 8N, 9N, 2N, NAA. (Item #: 178595, Ref: 351505K16) $13.70

Differential Pinion Bearing Cup - For Ford tractor models Dexta (1957-1964), NAA (1953-1954), 2N (1939-1952), 8N (1939-1952), 9N (1939-1952), 600 (With 4 Speed Transmission, s/n 54166-later, 1958-1962), 601 (With 4 Speed Transmission, s/n 54166-later, 1958-1962), 2000 (1965-later), 2120 (With 4 Speed Transmission, s/n 54166-later, 1958-1962), 3000 (1965-later), 4110 (1965-later), Compatible with Ford Construction and industrial models A64, Replaces Ford OEM number BB4422, 3920, (Item #: 109577) $18.30

Drag Link Assembly - This Tie Rod Assembly includes 8N3314D tube with both ends with clamps. Tube measures 32.75 inches. Overall measures 35 inches center to center when both ends adjusted in to stop, 9/16 inch by 18 pitch stud, includes Zerk fittings. For tractor models 8N, 9N, 2N. (Item #: 113709, Ref: 8N3314COMPLT) $77.00

Drag Link Clamp - This Drag Link Clamp is used on Ford tractor models 9N, 2N, 8N, NAA, Jubilee, 500, 501, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000 and 1801, 1939-1964. It replaces 8N3287. (Item #: 184034, Ref: 8N3287) $6.10

Drag Link Clamp - For Ford tractor models Dexta, NAA, Super Dexta, 2N, 8N, 9N, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 2031, 2100, 2110, 2120, 2130, 2131, 2300, 2310, 2600, 2610, 2910, 3000, 3100, 3110, 3120, 3300, 3310, 3600, 3610, 3900, 3910, 4000, 4031, 4100, 4110, 4120, 4121, 4131, 4140, Compatible with Ford Construction and industrial models 230A, 231, 233, 333, 530, 531, Replaces Ford OEM number 957E3287, 8N3287, (Item #: 104589) $5.40

Drag Link Dust Cover - Steering Drag Link Rear Ball Joint Cover. For tractors: 8N, 9N, 2N, NAA, 600, 800 (1939-1957). Center is black rubber. Small hole end is 5/8 inch hole, Large end is 1 7/16 inch inside diameter. (Item #: 178186, Ref: 9N3324) $13.20

Drag Link Dust Cover - Rear Tie Rod Boot with leather insert. Fits tractor models: Jubilee, NAA, NAB, 2000 4 cylinder, 2030, 2031, 2120, 2130, 2131, 2N, 4000 4 cylinder, 4030, 4031, 4120, 4121, 4130, 4131, 600, 601, 800, 801, 8N, 9N. All 4 cylinder 1939 to 1964. 1.425 inch base, .850 inches tall, .700 inch hole. Replaces: 9N3324, A0NN3324. (Item #: 178150, Ref: 9N3324OE) $16.80

No
Picture
Drag Link End, Front - 11/16 inch UNF-Right Hand Thread. For tractor models 9N, 2N. (Item #: 100668, Ref: 9N3270B) $12.40

Drag Link End, Front - This Drag Link End is exactly like the NAA3270A except it is sealed, meaning you never have to grease them! Sealed, A= 3.875 inches, B= .687 inches, 18 left hand thread. Manual steering. For tractor models 8N, 9N, 2N, NAA, NAB, 600, 601, 800, 801, 2000 (4 cylinder 1/1962 to 12/1964), 4000 (1/1962 to 12/1964). Price shown is for each, sold only in multiples of 2 items. Almost exactly the same as 8N3270 except the castle nut end threaded section is 1/16 of an inch longer. (Item #: 100671, Ref: NAA3270A-N) $11.30

Drag Link End, Front - A= 3.875 inches, B= .687 inches, 18 left hand thread. Manual steering. For tractor models 8N, 9N, 2N, NAA, NAB, 600, 601, 800, 801, 2000 (4 cylinder 1/1962 to 12/1964), 4000 (1/1962 to 12/1964). Almost exactly the same as 8N3270 except the castle nut end threaded section is 1/16 of an inch longer. (Item #: 100671, Ref: NAA3270A) $11.30

Drag Link End, Front, RH Thread, Greasable - End Assembly, Front, .687-18 right hand thread, 3.187 inch from center of post to end of large thread. For 9N, 2N. (Item #: 100668, Ref: 9N3270) $12.40

No
Picture
Drag Link End, Front, RH Thread, Non-Greasable - Sealed, End Assembly, Front, .687-18 right hand thread, 3.187 inch from center of post to end of large thread. For 9N, 2N. (Item #: 100668, Ref: 9N3270-N) $12.40

Drag Link End, Rear - Length 4.250 inches, .687 inch diameter, 18 right hand thread. For tractor models: 8N, 9N, 2N, 2000 4 cylinder 1962-1964, 2031, 2120 1963-1964, 2131, 4000 1962-1963, 4031, 4120, 4131, 600, 601, 800, 801, NAA, NAB. (Item #: 100670, Ref: NAA33271A) $12.70

Drag Link Tube - 34.5 inches long. Uses one right hand (NAA33271A) and one left hand (NAA3270A) Tie Rod End. For tractor models 9N, 2N, (used on right hand side on early 8N and left hand side on late 8N), Dexta, Super Dexta. (**BEFORE ORDERING: Measure your drag link tube length, part number 8N33314D drag link tube was also used on 9N, 2N and 8N tractors. It is 32-3/4 inches long). (Item #: 114042, Ref: 8N33315) $48.00

Drag Link Tube - 32-3/4 inches long. Outside diameter 0.875 inch. Includes clamps (on each end), For 8N, 9N, 2N (For complete tie rod assembly add front drag link ends 8N3270 AND rear drag link ends NAA33271A. (**BEFORE ORDERING: Measure your drag link tube length. Part number 8N33315 drag link tube was also used on these tractors. It is 34-1/2 inches long). (Item #: 105276, Ref: 8N3314D) $55.00

Front Axle Assembly with Bushing - For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 800, 820, 840, 850, 2000 (with Manual 7-57/PS 55), 4000 (with Manual 7-57/PS 55), Dexta, Super Dexta. This axle is for tractor models that have a standard front end (NOT for adjustable axle). Not warrantied for use with front end loaders. Replaces NAA3010B2. (Item #: 112019, Ref: D9NN3010EA) $190.00

Front Axle Pin - This Front Axle Pin is the early type used on Ford 9N. Pin is 4.31 inches long. The front hole is 0.785 inches in diameter. 1.743 inch outside diameter. It replaces original part number 9N3126A. Uses 350635S retaining bolt, sold seperately. (Item #: 184017, Ref: 9N3126A) $62.00

Front Axle Pin Retaining Bolt - Used on 9N tractors only, with pin 9N3126A. This part replaces 350635S, 350635-S, 350635S7, 350635-S7 (Item #: 183006, Ref: 350635S) $5.50

Front Spindle - For early 9N without keyway in vertical shaft. Secured with tapered set screw. Reversible, left or right. Replaces 9N3105 (Item #: 178661, Ref: S.61380) $203.00

Front Spindle - Right Hand Spindle. For 9N, 2N. Height of spindle shaft is 11 inches. Keyway on inside is 5/16 inches. Notch on outside of shaft. The wheel bearing kit used for this spindle is part number WBKFD1. (Item #: 100619, Ref: 2N3105) $42.98

Front Spindle - Left Hand Spindle. For 9N, 2N. Height of spindle shaft is 11 inches. Keyway on inside is 5/16 inches. Notch on outside of shaft. The wheel bearing kit used for this spindle is part number WBKFD1. (Item #: 100620, Ref: 2N3106) $51.98

Gasket, Steering Gear Housing, Front - For tractor models 9N, 2N 1939-1947. (Item #: 178151, Ref: 9N3594) $3.00

Gasket, Steering Gear Housing, Rear - For tractor models 9N, 2N 1939-1947. (Item #: 178152, Ref: 9N3593B) $7.08

Pin, Front Axle - Outside diameter 1.743 inch, inside diameter 1.310 inch, length 4 inches. For tractor models 9N, 2N (serial number 164489 and up), 8N. Hardened steel. The part has a fully open end which will accommodate a loader pump shaft. If you need OEM style with smaller opening, order 2N3126E. (Item #: 112069, Ref: 2N3126D) $30.34

Radius Rod, Ball Socket - For tractor models: Jubilee, NAA, 2000 3 cylinder, 2000 4 cylinder, 600, 601, 800, 801, 1811, 1821, 1841, 1871, 1881, 2030, 2100, 2110, 2120, 2130, 2150, 2300, 2310, 2600, 2600V, 2810, 2910, 2N, 3000, 3055, 3100, 3110, 3120, 3150, 3300, 3310, 3330, 3600, 3600V, 3610, 3900, 3910, 4000 3 cylinder, 4000 4 cylinder, 4030, 4100, 4110, 4120, 4121, 4130, 4140, 4410, 4600SU, 8N, 9N, 230A, 231, 233, 234, 333, 334, 335, 340, 530A, 531, 540, 3400, Dexta, Super Dexta. Replaces: 9N3442, E0NN3N442BA, C5NN3N442C, C5NN3N442A, GL139. (Item #: 115083, Ref: E0NN3N442BA) $17.40

Radius Rod Ball Spacer, Used - For Ford tractor models Dexta, NAA, Super Dexta, 2N, 8N, 9N, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 761, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2100, 2110, 2120, 2130, 2150, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3300, 3310, 3330, 3400, 3600, 3610, 3900, 3910, 4000, 4030, 4100, 4110, 4120, 4121, 4130, 4131, 4410, 4600SU, 4610, Compatible with Ford Construction and industrial models 230A, 231, 233, 234, 333, 334, 335, 340, 531, 532, 540, 541, 1801, 1811, 1821, 1841, 1871, 1881, 2030, 4140, Replaces Ford OEM number E0NN3N442BA, For a new version of this item use Item #: 115083, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 459476) $10.92

Radius Rod, Socket Cap - Used with Socket E0NN3N442BA. Replaces: E0NN3N406BA, 8N3440B, C7NN3N406A, 957E3440B, 83924040, 957E3440A, 313319. (Item #: 108088, Ref: E0NN3N406BA) $10.80

Seat Shock Bushing - This bushing is for the horizontal bolt hole. It measures 1.223 inches outside diameter at the largest point. The hole inside diameter is 0.597 inches. The length measures 0.724 inches overall. 2 to 4 used per shock. This part replaces 72696R1, 70222488, T19118, 230288, 250416R1, F3296R, R26832, 760674M1. Used with optional Monroe seat (Item #: 109602, Ref: 72696R1) $2.30

Spindle Bushing - FORD Spindle Bushing - 1.250 inch inside diameter, 1.370 inch outside diameter, 1.500 inches long. Fits many models. Two are used 1955 and later. Four used per tractor 1939-1954. Sold individually. Replaces: 2N3109, 81802940, 957E3109B, C5NN3446A. (Item #: 100617, Ref: 2N3109) $4.00

Spindle Dust Seal - This Spindle Dust Seal is used on Ford 9N and 2N Tractors. It replaces original part number 9N3528. (Item #: 108951, Ref: 9N3528) $2.70

$Ford 9N Spindle \ King Pin Repair Kit$
Spindle / King Pin Repair Kit - For 8N, 9N, 2N, NAA, Jubilee. Spindle Repair Kit includes 2 each of: upper spindle seal C5NN3125A, spindle top bushing 2N3109, spindle bottom bushing 2N3109, and thrust bearing C0NN3123B. (Item #: 180785, Ref: S.65986) $36.00

Spindle Nut - Fits on Front Spindles. Castle Nut 3/4 inch x 16 UNF. Replaces P2060, VLG3307, 351129S, 353928X1, 354573S36, 387930S36, 646060M1, 83416613, 83900513, 83910701, 880284M1, 9073, 98A750N. (Item #: 156038, Ref: 387930S36) $1.10

Spindle Thrust Bearing - Thrust Bearing for Spindle measures 1.345 inch inside diameter, 2.2 inch outside diameter, and width of .622 inch. For tractor models 2000, 2600, 2N, 3000, 3600, 3900, 4000, 4100, 4600SU, 600, 700, 800, 8N, 900, 9N, Dexta, NAA, Jubilee, Super Dexta. (Item #: 100623, Ref: C0NN3123B) $5.00

Steering Column Collar - For 9N, 2N. Collar, retains dust seal in top of column. Exactly Like Original. WITHOUT GREASE FITTING HOLE. (Item #: 178630, Ref: 9N3669A) $9.30

Steering Column Collar with Grease Fitting Hole - This Steering Column Collar comes with dust seal and spring. Comes with a primer paint coat on cover and with the grease fitting hole. Replaces 9N3669 cap, 9N3699 spring and 9N3660 dust seal. Fits 9N and 2N. (Item #: 178088, Ref: 9N3669BPLUS) $14.10

Steering Column Collar with Grease Fitting Hole - For 9N, 2N. Collar with grease fitting hole, retains dust seal in top of column. Exactly Like Original. WITH GREASE FITTING HOLE. (Item #: 178629, Ref: 9N3669B) $9.60

Steering Column Dust Seal - For tractor models 9N, 2N. 1939-1957. (Item #: 178153, Ref: 9N3660) $2.98

Steering Column Felt Dust Seal Retainer - This Steering Column Felt Dust Seal Retainer is used on Ford 9N and 2N 1939-1947. It replaces original part number 9N3661. (Item #: 178089, Ref: 9N3661) $3.70

Steering Column Retainer and Spring - Parts Now Sold Separately as 9N3699-9N3661. For 9N, 2N. Steering Column Spring Retainer. Exactly Like Original Spring and Retainer. (Item #: 9N3699-9N3661) $9.58

Steering Column Spring - This Steering Column Spring is used on Ford 9N and 2N tractors, 1939-1947. Replaces 9N3699 (Item #: 179395, Ref: 9N3699) $3.60

Steering Gear Housing Gasket - For tractor models 9N after serial number 47509 and all 2N. Replaces 9N7223B (Item #: 180733, Ref: 9N7223B) $7.50

Steering Gear Housing Gasket - This Steering Gear/Gear Shift Housing Gasket is used on 9N Tractors before serial number 47508. It replaces original part number 9N7223A. (Item #: 183029, Ref: 9N7223A) $7.50

Steering Gear Set - Fits 9N and 2N tractors 1939-47. Set contains one each of 9N3525 Shaft and pinion assembly, 9N3526 steering sector, right hand, and 9N3527 steering sector, left hand. (Item #: 183791, Ref: SGS3) $345.00

Steering Sector Gear Bushing - For tractor models 9N, 2N. Priced per package of two halves. Order 2 packages for complete tractor. (Item #: 112961, Ref: 9N3517) $28.60

Steering Sector Gear (LH) - For tractor models 9N, 2N. (Item #: 108526, Ref: 9N3527) $158.00

Steering Sector Gear (RH) - For tractor models 9N, 2N. (Item #: 108525, Ref: 9N3526) $155.00

No
Picture
Steering Sector Gear - Right Hand, Used - For Ford tractor models 2N, 9N, Replaces Ford OEM number 9N3526, This is for the right-hand side, For a new version of this item use Item #: 108525, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 435400) $92.01

Steering Sector Shaft Packing, Pair - Four Pieces required per tractor. Price is for two pieces. For tractor models 9N, 2N 1939-1947. (Item #: 129635, Ref: 9N3670) $26.00

Steering Shaft and Pinion - Fits 9N and 2N tractors 1939 to 1947. Contains shaft and pinion only. For complete set use Part number SGS3. (Item #: 108524, Ref: 9N3525) $95.00

Steering Shaft Bearing - For tractor models 9N, 2N. Replaces 683571A. Price is for 1. Two are used on the steering shaft, one at the top and one at the bottom. (Item #: 111285, Ref: 5BC-TIM) $14.50

Steering Shaft Bearing Cone (1) - Upper or Lower Bearing Cone for Models: 9N, 2N. Two used per tractor. Price is for each. Replaces 9N3573 (Item #: 111625, Ref: 4CB-TIM) $24.60

Steering Shaft Bearing Cup - For tractor models 9N, 2N. Price is for 1. Two are used on the steering shaft, one at the top and one at the bottom. Replaces B3552. (Item #: 111635, Ref: 6-TIM) $11.10

Steering Wheel - This Restoration Quality steering wheel measures 18 inch diameter, with 3/4 inch keyed hub, and has 4 covered steel spokes. For model 9N 1939-1940. Replaces 9N3600B. (Item #: 101420, Ref: S.67507) $55.98

Steering Wheel - For 9N and 2N. 17 5/8 inch diameter, 11/16 inch keyed hub. Replaces OEM part number 2N3600. Looks just like original with bare spokes! For 9N and 2N. (Item #: 101418, Ref: R2090) $27.00

Steering Wheel - Keyed, steel spokes. Wheel measures 17 1/2 inches in diameter and 3/4 inch hub. Replaces E0NN3600AA (Item #: 101418, Ref: 180576M1-OE) $27.00

Steering Wheel - 17-5/8 inch diameter, 11/16 inch-13/16 inch keyed, 3 covered steel spokes. For tractor models: 9N, 2N 1939 to 1947. Replaces 2N3600. (Item #: 122474, Ref: 180576M1) $24.30

Steering Wheel Nut - Zinc Plated Steel Nut, Steering Wheel Acorn Style. 5/8-18 for 9N and 2N (1939-1947). Head uses a 1 inch wrench. (Item #: 183746, Ref: 351103S) $9.30

Steering Wheel Nut - Black - For Ford tractor models NAA, 2N, 8N, 9N, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2031, 2110, 2111, 2120, 2130, 2131, 4000, 4030, 4031, 4110, 4120, 4121, 4130, 4131, 4140, Compatible with Ford Construction and industrial models 1801, 1811, 1821, 1841, 1871, 1881, 2030, 4040, Replaces Ford OEM number 359295S7, Black Finish, 11/16" - 20 Threads, (Item #: 111727, Ref: 351114CCBLACK) $6.60

Steering Wheel Nut, Chrome - Nut, Steering Wheel ACORN Style. 5/8-18, CHROME PLATED. For tractors: 9N, 2N {1939-1947}. Head uses a 1 1/8 inch wrench. (Item #: 150988, Ref: 351103CC) $8.10

Steering Wheel Washer - This Steering Wheel Washer is used with 4 spoke steering wheel. It has a 1.80 inch outside diameter. It replaces original part number 9N3673 (Item #: 179387, Ref: 9N3673) $7.44

$Ford 9N Tie Rod Assembly - L\H$
Tie Rod Assembly - L/H - Like Original. Adjustable from approximately 38-1/2 inches to 39-3/16 inches center-to-center tie rod studs. 1939-1947. (Item #: 125345, Ref: 9N3305-OEM) $100.00

$Ford 9N Tie Rod Assembly - R\H$
Tie Rod Assembly - R/H - Like Original. Adjustable from 38.5 to 39.2 inches. (Item #: 125346, Ref: 9N3304-OEM) $101.00

Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16 inches x 5/8 inch x 5/8 inch, 1 15/16 inches x 3/4 inch, 3/4 inch, and 1 3/8 inches x 1 inch x 1/2 inch. (Item #: 183427, Ref: TIERODBOOTS) $13.00

Wheels

12" x 28" 6 Loop Rear Rim, Used - For Ford tractor models NAA, 2N, 8N, 9N, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2031, 2100, 2110, 2111, 2120, 2130, 2131, 2150, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3100, 3120, 3300, 3310, 3330, 3400, 3600, 3610, 3900, 3910, 3930, 4000, 4030, 4031, 4100, 4110, 4120, 4121, 4130, 4131, 4600, 4610, 4630, 4830, 5030, 5600, 5700, 6600, 6700, 7600, 7700, Compatible with Ford Construction and industrial models 233, 234, 334, 335, 340, 420, 445, 515, 530, 531, 532, 535, 540, 541, 545, 1801, 1811, 1821, 1841, 1871, 1881, 2030, 3500, 4040, 4140, Replaces Rims, Wheels, Tires OEM number C7NN1050N, 31319712G, 99A502, D4NN1050B, D9NN1050EA, RW12286, TR1228, Rim Width: 12", Rim Diameter: 28", Type: 6 Loop, 12X28, May Fit More Applications Than Listed, For a new version of this item use Item #: 103720, Additional Handling and Oversize Fees Apply To This Item, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 403720) $99.01

Bearing Cone - BEARING CONE For 9N, 2N (Item #: 09074) $8.80

Bearing Cone, Front Wheel, Inner - Cone. For 9N, 2N (Item #: 172510, Ref: B1201) $8.30

Bearing Cone, Front Wheel, Outer - Tapered Cone. For tractor models 9N, 2N. (Item #: 182875, Ref: B1216) $9.70

No
Picture
Bearing Cup - BEARING CUP For 9N, 2N (Item #: 180095, Ref: 15250) $6.00

Bearing Cup, Front Wheel, Inner - Cup. For 9N, 2N (Item #: 180095, Ref: B1202) $6.00

Bearing Cup, Front Wheel, Outer - For tractor models 9N, 2N. (Item #: 172755, Ref: B1217) $7.50

Bolt. Front Wheel - This bolt is the Hub to Rim Bolt. Measures 1 5/8 inches x 20 UNF threads, .6 inch shoulder diameter, 1.346 inch usable length, 1.545 inch overall length. For 2000, 2N, 3000, 4000, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 9N, NAA, Jubilee. Replaces 81816078, C5NN1107B, C5NN1107D, C5NN1107E, 78-1107 and 781107. Uses nut part number C5NN1012B. (Item #: 154744, Ref: C5NN1107E) $3.70

Center Disc to Rear Axle Bolt - 1.87 inches long, 5/8 inch x 18 UNF right hand threads. For tractor models 9N, 2N. (Item #: 126618, Ref: 9N1117) $8.50

Front Rim 3 x 19 - Fits 9N and 2N. 5 Lug. Rim size: 3.00 inch x 19.00 inch 9.75 inch pilot (center) hole. For 4.00 inch x 19 inch tire. (Item #: 103759, Ref: 9N1015A) $86.00

Front Rim (Blank) - Blank (no center) Front Rim, 3 inch x 19 inch. Center must be removed from old rim and welded into new rim. For 8N, 9N, 2N. (Item #: 103758, Ref: R0651) $65.45

Front Tire - This is a three rib 4.00 x 19 inch tire for 8N, 9N and 2N. If you need the tube, it's part #281890. (Item #: 118222, Ref: R2074) $94.00

Front Wheel Bearing Kit - For model 9N, 2N 1939-1947, 8N 1948-1952, NAA, Jubilee thru 1954. Kit includes inner Cone (86609936), inner cup (86609935), outer cone (86576860), outer cup (86577043), seal (NCA1190A). (Item #: 100651, Ref: CBPN1200A) $26.00

Front Wheel Cap - For 8N, 9N, 2N, NAA, 501, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000 all 1939 to 1964. Front Wheel Cap. (Item #: 183735, Ref: 2N1139B) $6.10

Front Wheel Hub - Front Wheel Hub comes with Studs. For 8N, NAA. Uses CBPN1200A wheel bearing kit. Will also work with 9N and 2N tractors when retrofitted with 6 lug hub and rim. Replaces: 8N1104, NCA1104C, D5NN1104A (Item #: 184817, Ref: 86511582) $97.92

Front Wheel Nut - This Front Wheel Nut is an EXACT reproduction of the ORIGINAL part. Hex style 11/16 inch outside diameter. Tractors: 9N, 2N (1939 to 1944). (Item #: 178190, Ref: 9N1012) $2.80

Rear Rim - This rim is 9 inch x 28 inch wide base demountable rim with 6 loop clamps. Loops are designed for 5/8 inch bolts. Fits tire size 11.2 inch x 28 inch. (Item #: 103780, Ref: NCA1020C) $126.00

Rear Rim - This rear rim is six loop, 10 inch x 28 inch. Loops are designed for 5/8 inch bolts. For 8N, 9N, 2N, NAA, Jubilee, 600, 800, 900, 2000, 4000, Dexta, Super Dexta and others by size. Replaces NCA1020B. (Item #: 103719, Ref: NCA1020B) $143.00

Rear Rim - This Six loop rim is 11 inch x 28 inch. Loops are designed for 5/8 inch bolts. For 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 800, 900. (Item #: 104209, Ref: C5NN1050E) $164.00

Rear Rim - This Six loop rim is 12 inch x 28 inch. Loops are designed for 5/8 inch bolts. For 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 800, 900, 2000, 3000, 4000. Replaces D4NN1050B, D9NN1050EA, 31319712G, 99A502 (Item #: 103720, Ref: R2068) $150.00

Rear Rim Bolt Kit - This Rear Rim Bolt Kit is a set of six bolts, nuts and washers. They are 5/8 inches-18 x 2.82 inches long. Replaces: 33806S34, 33806S36, 33806S7, 350719S8, 370938S36, 370938S43, 408, 81821369. (Item #: 184824, Ref: 350719KIT) $23.50

Rear Wheel Center - This disc is used on multiple Ford models. Check measurements before ordering. Disc, rear wheel 28 inch and 32 inch, 8-bolt hub, 6-bolt rim. Center hole: 4-5/16 inches, hub pattern: 8 lug - 6 inch bolt pattern. Replaces Ford OEM numbers D9NN1036CA, F1NN1036KA, 86512668, C5NN1036D, 957E1017B. Additional $35 shipping due to weight. (Item #: 149804, Ref: D9NN1036CA) $225.00

Seal, Front Wheel Hub - Front Wheel Hub Dust Seal. 2 11/16 inch outside diameter, 2 inches inside diameter. Fits: 2000 1955-1964 USA BUILT, 2N 1939-1947, 4000 1955-1964 USA BUILT, 600 1955-1964 USA BUILT, 700 1955-1964 USA BUILT, 800 1955-1964 USA BUILT, 8N 1948-1952, 900 1955-1964 USA BUILT, 9N, NAA 1953-1954. Price shown is for each. Can replace 9N1190B. (Item #: 113706, Ref: NCA1190A) $3.50

Spindle Tab Washer - This Tab Washer is used on some Ford Tractors 1939-and later. Measures 1.516 inch outside diameter, 0.78 inch inside diameter, 0.089 inch thick. It replaces original part numbers C5NN1N195A, 81811561, 9N1195. (Item #: 164443, Ref: C5NN1N195A) $1.50

No
Picture
Tire Tube 24 Inch - This 24 inch tire tube is used for all tractors with the following tires: 10.00 x 24, 11.00 x 24, 11.2 x 24, and 12.4 x 24. (Item #: 178957, Ref: WHS059) $56.00

No
Picture
Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 12.00 x 28, 13.00 x 28, 13.6 x 28, and 14.9 x 28. (Item #: 178895, Ref: WHS061) $116.00

Tire Tube 4.00 x 19 - Fits 4.00 by 18 and 4.00 by 19 tires. For 9N, 2N and 8N tractors that use the 4.00 by 19 inch tire. (Item #: 118305, Ref: 281890) $19.50

Wheel Rim, Rim Size: 10 x 28 - The Assembly Contains a 10 x 28 Rim, the center disc and hardware. Comes assembled. Suitable for Tire size: 12.4 x 28, Alternative Tire size: 11.2 x 28. The rim measures 10 Inches from bead to bead where the tire rests. Center hole: 4-5/16 inches, hub pattern: 8 lug - 6 inch bolt pattern. Verify all measurements before ordering. Replaces D9NN1036CA, D9NN1036CA, F1NN1036KA, 86512668, C5NN1036D, 957E1017B, C0NN1050F, NCA1020B, 33806S34, 33806S36, 33806S7, 350719S8, 370938S36, 370938S43, 408, 81821369. Additional $35 shipping due to weight. (Item #: 178951, Ref: S61968) $635.00

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $365.01

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Cooling System

Thermostat Housing to Block Gasket - Tractors: all 4-cylinder, 1953-1964, gas and diesel. Bolt holes measure 3/8 inch in diameter, and center to center of bolt hole spacing is 2 3/4 inches. Sold and Priced as Each. (Item #: 191970, Ref: EAF8255A) $5.20

Decals and Emblems

Decal, Fear This Ford - 12-1/2 inches x 3 inches. For all Ford tractors. (Item #: 183476, Ref: S.67825) $15.87

Sherman Transmission Instruction Plate - For Ford models with Sherman step up step down transmission. Installs under steering wheel nut. (Item #: 178113, Ref: SHERMAN) $20.40

Drive Train

Shift Cover Plate Gasket - For all models with 5-SPEED transmission built between 1955-1964. Not for tractors made overseas, such as Major, Dexta, etc. (Item #: 178105, Ref: NDA7223A) $7.10

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $94.00

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.50

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.90

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.20

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter Solenoid, 12 Volt - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. (Item #: 150223, Ref: DR1467) $19.70

Switch, Push Button - This 2 terminal switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch overall length. Check measurements before ordering if using as a universal part. Applications include ether switch, horn button, cold start, starter switch, and manifold heater switch. It replaces 22702, 240962, 242988, 245866, 245936, 70253322, 71191589, 72160068, VT507, 86900358, A30858, O9995AB, T18524, TG07803, TO18117, TO7803, 271179R91, 367678R91, 373611R91, 393209R91, AR46184, AR47373, AR47374, R39554, 189158M91, 767828M91, 105386A, 10A972, 1K7392C, UT2421, 1K7392A, 7A7392. (Item #: 121141, Ref: R7994) $12.00

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Pistons and Sleeves

No
Picture
Seal Kit - Seal kit, for cylinder E2NN3A540BA. Piston rod is retained with 1" snap ring and 1-3/4" threaded spanner nut. (Item #: E2NN3X-SK) $64.99

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $78.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $108.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $176.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00

Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00

$Ford 9N Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10

$Ford 9N Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$Ford 9N Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.80

$Ford 9N Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40

$Ford 9N Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60

$Ford 9N Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40

Rain Cap - This rain cap is for a 4.00 inch pipe. (Item #: 108645, Ref: R1807) $11.00

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60

Rain Cap - This rain cap is for a 5.00 inch pipe. (Item #: 108750, Ref: WC15) $16.90

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.50

Fuel System / Air Intake

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $12.70

Filter Screen and Gasket for Sediment Bowl - 1-1/2 inch outside diameter seal (for a 1 9/16 inside diameter housing and a 1 3/8 inch outside diameter screen. Measure before ordering. For tractor models (1958-1964 All with 134 cubic inch engines), 2000 4 cylinder, 501, 601, 701, (1958-1960 all with 172 cubic inch engines up to 126524), 801, 901, 1801. (Item #: 150700, Ref: ABC346) $5.40

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.10

Gauges

Ammeter, Black, Flat Bezel - For all models to 1958. Terminal type ammeter. 30-0-30. Black ring. Replaces FAD10850A. (Item #: 110410, Ref: A0NN10670A-BLAC) $6.98

No
Picture
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $59.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $39.90

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $14.90

Hitch / Drawbar

Drawbar - Number Of Drawbar Holes: 11 Hole``Made of 1" x 2-1/2" high carbon steel``Category: 1``Length: 26"``End Pins: 7/8"``Hitch Pin Holes - 3/4" (Item #: 103174, Ref: 9N5182) $44.30

Drawbar Check Chain Kit - This Drawbar Check Chain Kit includes: right hand/left hand anchors, 2 eyelets, 2 chains, 4 clevis with pins, and hardware. Fits: Jubilee, NAA, NAB, 2000 3 Cylinder, 2000 4 cylinder, 2600V, 2N, 3600V, 4000 4 Cylinder, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 2030, 2031, 2100, 2110, 2111, 2120, 2121, 2130, 2131, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3110, 3120, 3300, 3330, 3600, 3610, [4030, 4130, 4140 (4 cylinder)], 4031, 4040, 4100, 4110, 4120, 4121, 4131, 9N, Industrial: 231, 233, 333, 334, 335, 1801, 1811, 1821, 1841, 1871, 1881, 230A, 3400, 3500, 530A, Dexta, Super Dexta. Replaces: 957E597, 957E596, CBPN598A, NCA597B, NCA596B. (Item #: 115051, Ref: NCA596B) $38.00

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.28

Link End - Plated, forged, 1-1/4 inch thread, left hand, 1 inch hole. (Item #: 180473, Ref: RE1717L) $20.50

Link End - Plated, forged, 1-1/4 inch thread, right hand, 1 inch hole. (Item #: 174507, Ref: RE1718R) $21.58

Stabilizer Arm HD - Arm only, made of alloy spring steel, for kit 231253XHD, red only. 7/8 inch hole diameter. 31 1/2 inches center to center. (Item #: 110516, Ref: 230042XHD) $15.30

Top Link - Forged Top Link, 12 inch body, Category I implement ends. Adjusts 17.5 to 24 inches overall. 3/4 inch pin holes and both eyelets are 1 3/4 inch wide. Dichromate plated. (Item #: 103162, Ref: JSA1012C) $19.98

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System

Coupler Flange - FORD: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b (Item #: 108772, Ref: L36-6) $119.41

Coupler Flange - Drive flange; 3/4 inch round bore with set screw 1/4 inch x 3/8 inch. 1-15/16 inch spacing. For Morflex series 302. Replaces: L363, 191061, 1752219M91, L36-3 (Item #: 112104, Ref: 191061) $22.00

Coupler for Pump Shaft - The Hydraulic Pump Shaft Coupler is 1-1/2 Outside Diameter and 2-1/4 inches long. It 7/8 inch 13 splined inside. It replaces 1631413, 350-1631413, S340 (Item #: 114586, Ref: S340) $36.00

Cylinder Seal Kit, For 2 inch cylinders - For TISCO side and top link replacement cylinders. Seal Repair Kit for 2 inch cylinders. For cylinder numbers: HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. (Item #: 183971, Ref: HSK2002) $23.90

Cylinder Seal Kit, For 3 inch Cylinders - For TISCO brand side and top link replacement cylinders ONLY. Seal Repair Kit for 3" cylinders. For cylinder numbers: HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. (Item #: 179480, Ref: HSK3002) $31.40

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $25.70

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $14.70

Hub - 7/8 inch, 13 spline threaded, 3-7/8 inch hole spacing. For 730 LOADER. Used with C5NNN879A hub. (Item #: 160204, Ref: 291315) $65.00

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199) $21.10

Hydraulic Pump for Loader - Part Description: Pump, Hydraulic For 730 LOADER, 735 LOADER. SPECS: CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, PORT SIZE INLET: 1-5/8 inches-12 ORB, PORT SIZE OUTLET: 1-5/16 inches-12 ORB, MOUNTING: 2 bolt SAE "B", FORD PUMP APPLICATION: 730 and 735 loaders, CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, MOUNTING: 2 bolt SAE "B", INLET: 1-5/8 inches-12 ORB, OUTLET: 1-5/16 inches-12 ORB. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inches and Maximum is 6 7/8 inches. (Item #: 127269, Ref: 7702425-29Z) $760.00

Hydraulic Pump, Front Mounted - This Hydraulic Pump is used with some 701, 702 and 703 Loaders. It is 14 Gallons Per Minute at 2000 RPM. The shaft is 3/4 inch round with a key way. Left Hand Rotation. Inlet is 1 Inch NPT. Outlet is 3/4 Inch NPT. Mounting bolt spacing 4 3/16 inches center to center. Comes with two adapters. Contains: 1-720FSO-3/4X3/4 HC4008 adapter, 1-720FSO-1X1-1/4 HC4009 adapter. This Pump may work in other loader application. Verify Specs before ordering. (Item #: 182700, Ref: L827-10X-LB) $585.00

Hydraulic Valve Kit - Valve with handles, three-spool, 2000 p.s.i. Relief, all spools tandem (4-way) spring center to neutral. (Item #: HV4030) $787.98

LBP Coupler Center - Center member. Center member. 3-5/8" O.D., four 5/16" holes, 2-1/4" bolt circle (L52-10) For tractor models 352. (Item #: 178931, Ref: 192169) $71.00

LBP Hydraulic hose Assembly - Hydraulic hose assembly. For Ford model 740 LOADER. (Item #: 179521, Ref: 7701142) $29.70

Morflex Center Member - This is a 1-302 Morflex Center member. It measures 3-1/8 inch diameter, four 1/4 inch holes, 1-15/16 inch bolt circle. Replaces part numbers 893129, 191192, L5227, 1506097M91, 1086870M1, 191192LBP, 1752218M91, L52-27 (Item #: 116952, Ref: 191192LBP) $52.92

Top Link, Hydraulic - FORD: Hydraulic top link cylinder. All ports 9/16 inch-18 O-ring boss with two adapters 9/16 inch-18 ORBM x 1/4 inch NPTM 90 degree swivel. 3 inch cylinder bore, 8 inch stroke length, 26 inch closed length, 12-7/16 inch barrel length, 1 inch rod end diameter, 1-3/4 inch rod end width, 1 inch diameter base end. (Item #: 167145, Ref: HTL3103) $273.00

Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.60

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $120.00

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.80

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $98.00

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Lights

Headlight Assembly, 12 Volt - (Single) Headlight Assembly 12-volt, blue - Sealed beam headlamp assembly in heavy gauge steel housing with Rubber bezel. Does not look like original. (Item #: 184496, Ref: L525HB-12V) $51.00

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

No
Picture
Sealed Beam Bulb, 12 Volt - Red/white combination work/tail light, 4-1/2 inch diameter. (Item #: 116014, Ref: S.52670) $23.60

Tail Light Lens - Plastic 4 inch lens for DUOLAMP with FOMOCO stamped on lens (has 2 mounting screw holes spaced 3 1/8 inches apart). Fits tractors 1953 and newer. (Item #: 178144, Ref: FDV13450A) $16.50

Miscellaneous

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Tractor Umbrella with Frame & Mounting Bracket - Blue - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without Additional Handling & Oversize Fees Apply To This Item, tools, (Item #: 161190) $119.00

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Brownish Medium Gray, 1 Quart - Ford Brownish Medium Gray was used for the same applications as TP240Ford Medium Gray. This is a lighter shade. Since the tractors did not come off the production line all the same, the darker or light shades are completely up to the desires of the customer. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184575, Ref: TP245QT) $50.00

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $68.00

No
Picture
Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20

No
Picture
Paint, Empire Blue, 1 Gallon - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100713, Ref: TP360GAL) $56.00

No
Picture
Paint, Empire Blue, 1 Quart - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100712, Ref: TP360QT) $23.30

No
Picture
Paint, Empire Blue, Spray Can - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100711, Ref: TP360SP) $7.40

No
Picture
Paint, Ford White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108133, Ref: TP470SP) $10.20

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $55.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100120, Ref: TP2700SP) $8.90

No
Picture
Paint, Industrial Yellow, Spray - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100723, Ref: TP760SP) $7.80

No
Picture
Paint, Light Gray, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100716, Ref: TP330GAL) $57.00

No
Picture
Paint, Light Gray, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100715, Ref: TP330QT) $20.70

No
Picture
Paint, Light Gray, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100714, Ref: TP330SP) $8.90

No
Picture
Paint, Medium Gray, 1 Quart - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100718, Ref: TP240QT) $22.10

No
Picture
Paint, Medium Gray, Spray Can - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100717, Ref: TP240SP) $8.30

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $16.90

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.90

No
Picture
Paint, Vibrant Blue, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156586, Ref: TP365GAL) $91.00

No
Picture
Paint, Vibrant Blue, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156587, Ref: TP365QT) $37.20

No
Picture
Paint, Vibrant Blue, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156585, Ref: TP365SP) $10.40

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $44.10

PTO / Driveline

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $173.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

NOTE

PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.

NOTE

PTO Overide Clutch - This 6 spline Override Coupler converts a 1 1/8 inch diameter PTO shaft to 1 3/8. It has a 1 1/8 inch female at one end and 1 3/8 inch male at the other end). Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103169, Ref: C670F) $51.00

PTO Overide Clutch - Override coupler for 1 3/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 191020, Ref: C680F) $79.00

PTO Overide Clutch - Override coupler for 1 1/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103167, Ref: C690F) $67.80

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $279.00

Seats

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57

Seat Cushion, Black - Cover with piping and Ford script logo. Fits all 1939-1964 models with a 17 inch wide steel seat pan. (Item #: 115058, Ref: 8N401BLK) $51.00

Tie-On Seat Cover - Blue and White, 19 inches wide. Deluxe with 2 inches of foam. (Item #: 101353, Ref: R1013) $36.10

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $103.00

Sheet Metal / Body Parts

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $178.00

Steering

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $48.40

Steering Wheel Spinner Assortment - Complete wheel spinner assortment: includes 2 blue, 2 green, 3 red, 2 yellow and 3 black. (Item #: 185079, Ref: WSV125A) $123.80

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $24.30

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $307.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. (Item #: 103768, Ref: FW60166) $92.00

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166) $70.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $18.30

No
Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $64.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $66.00

Wheel Clamp - Wheel clamp holding disc to rim for double ramp type on power adjustable rims. For 28 inch rim on tractors 2000, 3000, 4140, (10-1968 to 1975); 2600, 3600, 4100, 4600SU except Baseldon models, (1981 to 3-1990); 3230, 3430, 3930, 4130, 4630, 4830LCG, (3-1990 to -) Use with rims PAR10X18 and C5NN1050J and C5NN1050H. Also replaces 3615259M1, 70235676 and 7000000241, E5NN1043AA. (Item #: 124526, Ref: 898021M1) $18.00

Wheel Front 8X16 - Front Wheel 8 inch x 16 inch ; 6 bolt, 6 inch circle, 4.62 inch pilot. (Item #: 180445, Ref: D5NN1007A) $106.00