Radiator Hose - Lower - For John Deere Construction and industrial models 300D, 310C, 410B, 410C, 410D, 415B, 510B, 510C, 510D, 515B, 610B, 610C, Replaces John Deere OEM number T100294, Smaller Side ID: 2.000", Larger Side ID: 2.312", For Hose Clamp use Item #: 130455, (Item #: 150827)$31.00
Radiator Hose - Upper - For John Deere Construction and industrial models 300D, 310C, 310D, 315C, 315D, 410B, 410C, 410D, 415B, 510B, 510C, 510D, 515B, 610B, 610C, 710B, 710C, 710D, Replaces John Deere OEM number T68579, B: 1.92" I.D., A: 2.00" I.D., For Hose Clamp use Item #: 130455, (Item #: 150790)$35.70
Water Pump - This Water Pump, with Gasket is used on 4-239D and 4-239T engines on John Deere Models 310C, 310D, 315C and 315D all without Air Conditioning. Replaces pumps with casting numbers R70612, R90785. Replaces original part number RE16666 (Item #: 140637, Ref: RE16666)$580.00
Water Pump Housing Gasket - Used on many John Deere tractors and other equipment, this gasket replaces John Deere part number R56809 (Item #: 155353, Ref: R56809)$6.40
Water Pump Seal Kit - This seal kit is used on multiple John Deere Tractors where water pumps with casting # R70437, R100812 or R78286 is used. Plastic installer included. (Item #: 164008, Ref: AR101549)$10.10
Alternator, 12 Volt - 65 amp, Motorola type, has AC post, Ign/Lmp post, B+ post. Regulator includes both IGN and Sense+ bolts. For tractor models 210C, 310C, 315C, 400G, 410B, 410C, 440D, 444D, 444E, 450G, 455G, 482C, 510B, 510C, 540D, 544D, 544E, 550, 550G, 555, 555G, 610B, 610C, 624E, 640D, 643, 643D, 644D, 644E, 644ER, 650G, 710B, 710C. (Item #: 117399, Ref: TY6678)$303.00
Blower Motor - Note, some John Deere applications require 2 R85234 orings to fit in the housing. These o-rings are not available though Yesterday's Tractors. This Blower motor is a double shaft, 12 volt single speed 2 wire motor with 3/8 inch shafts. Tractors: 1640, 2040, 2040S, 2140, 2350, 2550, 2750, 2940, 2950, 3040, 3140, 4030, 4040, 4040S, 4050, 4055, 4230, 4240, 4240S, 4250, 4255, 4350, 4430, 4440, 4450, 4455, 4555, 4560, 4630, 4640, 4650, 4755, 4760, 4840, 4850, 4955, 4960, 8430 4WD, 8440, 8450, 8630, 8640, 8650, 8850. Combine: 484, 4425, 6620, 6622, 7440, 7445, 7450, 7455, 7720, 7722, 8820, 9910, 9920, 9930, 9935, 9940, 9950, 9960, 9965, 9970, 9976. Backhoe: 310C, 315C, 410B, 510B, 510C. Wheel Loader: 544E, 624E. Forage Harvester: 5720, 5730, 5820, 5830. Sprayer: 6100, 6600, 6700. Windrower: 2320, 2420, 3430, 3830. Replaces R82005GV, RE251028, RE25160, AR82005 (Item #: 110507, Ref: AR82005)$83.00
Starter - This is a 12 volt, Delco style starter OSGR with 10 teeth and clockwise rotation. Replaces 1107577, 1990435, SE501428, TS-1173, TS-1308, TS-1574, TS-6145, TY25994, 1107599, 1107863, 1107871, 260-67101, AL41247, AL62690, AL70850, AMRE239087, AR66424, AT18150, AT25619, DRS2420, DRS4730, DRS4740, RE19187, RE19275, RE50095. Used on for diesel application. (Item #: 113951, Ref: RE239087)$170.00
Switch, Push Button - This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length. Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: AR46184, AR47373, AR47374, R39554, R39554. (Item #: 121141, Ref: R7994)$12.00
Engine Bearings
Main Bearings - .010 Oversize - Used on John Deere Diesel Engines: 202, 4039T, and 4045T, this .010 oversize bearing set replaces John Deere part numbers AT21110, AT21132 (Item #: 106804)$73.00
Main Bearings - .020 Oversize - Used on John Deere Diesel Engines: 202, 4039T, and 4045T, this .020 oversize bearing set replaces John Deere part numbers AT21112, AT21134, RE527235 (Item #: 106805)$59.00
Main Bearings - .020 Oversize - Used on John Deere Diesel Engines: 202, 4039T, and 4045T, this .020 oversize bearing set replaces John Deere part numbers AT21112, AT21134, RE527235 (Item #: 106806)$65.00
Main Bearings - .030 Oversize - Used on John Deere Diesel Engines: 202, 4039T, and 4045T, this ia .030 oversize bearing set replaces John Deere part numbers AT21136, RE27368 (Item #: 106806)$65.00
Main Bearings - Standard - Used on John Deere Diesel Engines: 202, 4039T, and 4045T, this bearing set replaces John Deere part numbers AT21139, AT21140 (Item #: 106803)$84.00
Engine Gaskets
Front Crankshaft Seal - This front crankshaft seal has a 2.175 inch Inside Diameter, a 3 inch Outside Diameter and is 0.38 inches wide. It Fits: 1032, 1042, 1052, 1055, 1065, 1068H, 1020, 3300, 210C, 300, 300B, 300D, 301, 301A, 302, 302A, 310, 310A, 310B, 310C, 310D, 315C, 315D, 400, 401, 401B, 401C, 401D, 410, 410B, 410C, 410D, 415B, 510B, 510C, 510D, 515B, 610B, 610C, 710B, 710C, 710D, 350, 350B, 350C, 350D, 350D, 355D, 355D, 400G, 450, 450B. Replaces: AR67942, AT21608 (Item #: 106849, Ref: AT21608)$7.00
Engine Rebuild Kits
No Picture
Engine Major Overhaul Kit - For 2140, 2250, 2450, 2555, 2555TSS, 2650, 2750, 2755, 2755CS/TSS, 2855, 2855N, 3430, 3820, 945, 952, 1052, 1155, 2850, 310C, 310D, 315C, 315D all Turbo with 4.239T Diesel, 300 Series, 4 cylinder, 4.19" bore, 1.6" pin. Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set. When ordering, specify in comments Main Bearing Size of Standard, .010, .020 or .030, Thrust Bearing Size of Standard, .010, .020 or .030, Connecting Rod Bearing Size of Standard, .010, .020, or .030. Camshaft Bushing of out dia. 020 O/S or in dia. 020 O/S. (Item #: RE54709)$856.23
No Picture
Engine Major Overhaul Kit - For 5500N, 5700, 6100, 6200, 6210, 6300, 6310, 6500, 515B, (300D, 310C, 315C, 315D, with Turbo) all with 4039T Diesel, 300 Series, Liter designated, 4 Cylinder, Conn Rod: R80032, R58979, R113612, 4.19" bore, 1.6" pin. Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set. When ordering, specify in comments Main Bearing Size of Standard, .010, .020 or .030, Thrust Bearing Size of Standard, .010, .020 or .030, Connecting Rod Bearing Size of Standard, .010, .020, or .030. Camshaft Bushing of out dia. 020 O/S or in dia. 020 O/S. (Item #: RE54709)$856.23
Camshaft - This Camshaft replaces those marked T20013 or T20014. It has multiple John Deere agriculture and industrial applications. Used so some of the following diesel and turbo diesel engines: 4.202, 4.218, 4.239, 4.267, 4039D, 4039T, 4045D. Verify casting numbers before ordering. Does not include tach drive. Replaces R82820, T20013 or T20014. Uses R81513 Screw In Tach Drive, not included, not available through YT. (Item #: 152042, Ref: R82820)$132.00
Camshaft - This Camshaft replaces those marked T20013 or T20014. It has multiple John Deere agriculture and industrial applications. Used so some of the following diesel and turbo diesel engines: 4.202, 4.218, 4.239, 4.267, 4039D, 4039T, 4045D. Verify casting numbers before ordering. Does not include tach drive. Replaces R82820, T20013 or T20014. Uses R81513 Screw In Tach Drive, not included, not available through YT. (Item #: 152042, Ref: R82820)$132.00
Connecting Rod Bolt - Used only for connecting rods with casting number: R80032, R80034, R81410, R121092, or R113612. Check casting number before ordering. 2.325 inch long. (Item #: 123880, Ref: R80033)$2.80
Engine Rings
Piston Rings - Ring set for 3 ring piston~ 1 used per piston. For 276 CID 4 cylinder diesel non-turbo engine~ 4.19 standard bore, 3 ring piston. Compression Rings 1 at .125 inches, 1 at .094 inches. Oil Rins 1 at .140 inch. Used on John Deere 3, 4 and 6 cylinder engines: 3029, 3029T, 3179, 4039, 4045, 4045T, 4239A, 4239D, 4239T, 4276, 6059, 6059T, 6068D, 6068H, 6068T, 6359A, 6359T, 6414D, 6414T Replaces RE15674, RE48818, RE516267, RE66820, RE507852 (Item #: 120925, Ref: PRSD461)$23.70
Coupling, Front Drive Shaft - This Front Drive Shaft Coupling is used on front Hydraulics on multiple John Deere Models. It is used with L34569 Coupling and R78202 Cushion. Replaces Original Part Numbers: L34432, T58194 (Item #: 154893, Ref: L34432)$15.80
Drive Pin for Coupler Drive - This Drive Pin for Coupler Drive is used on front Hydraulics on multiple John Deere Models. It has 9/16 inch Thread Length. It Threads into the Coupler End. It replaces John Deere Part Numbers AT42308, AT42311, AT42312, R34360 (Item #: 108512, Ref: R34360)$3.80
Hydraulic Coupler Bushing, Set of 4 - Hydraulic Coupler Bushing Kit is used on Front Hydraulics Couplings. It fits multiple John Deere Models. Replaces Original John Deere Part Numbers R45822, AR45822, AR49427 (Item #: 111302, Ref: R45822)$3.10
Hydraulic Pump Drive Coupling - Hydraulic Pump Drive Coupling is used front Hydraulics on multiple John Deere Models. It is used with L34432 Coupling and R78202 Cushion. Replaces L34569, T58195 (Item #: 154894, Ref: L34569)$15.10
Hydraulic Pump Drive Cushion - Hydraulic Pump Drive Cushion is used front Hydraulics on multiple John Deere Models. It is used between L34432 Coupling and L34569 Coupling. Replaces R78202, T58196 (Item #: 114011, Ref: R78202)$8.00
Hydraulic Seal Kit - Boom Cylinder - For John Deere Construction and industrial models 210C, 310C, 310D, 410B, 410C, 410D, 455G, 510B, 510C, 510D, 555G, 610B, 610C, 650G, 862B, Replaces John Deere OEM number RE20595, (Item #: 153359)$42.00
Hydraulic Seal Kit - Bucket Cylinder - For John Deere Construction and industrial models 310C, 410C, 410D, 510C, 510D, 610C, 710C, 710D, Replaces John Deere OEM number AT142582, Rod: 2", Bore: 3", (Item #: 152957)$45.00
Hydraulic Seal Kit - Dipper Cylinder - For John Deere Construction and industrial models 210C, 310C, Replaces John Deere OEM number AT101377, Rod: 1-1/4", Bore: 2-1/2", (Item #: 153278)$46.00
No Picture
Hydraulic Seal Kit - Lift Cylinder - For John Deere Construction and industrial models 310, 310C, 310D, 444J, 650G, 710C, 710D, 750B, Replaces John Deere OEM number AH149844, AH148164, (Item #: 153252)$43.00
Hydraulic Seal Kit - Loader Bucket Cylinder - For John Deere Construction and industrial models 310C, 310D, 550, 644G, Replaces John Deere OEM number AH149843, Bore: 90 MM, (Item #: 153017)$45.00
Oil System
Oil Cooler - Hydraulic - For John Deere Construction and industrial models 310C, 315C, 315CH, Replaces John Deere OEM number AT135264, AT113840, Core Height: 23", Core Width: 19-1/4", Depth: 2-3/8", Fitting Inlet: (2) 5/8" Beaded Tube, Fitting Outlet: (4) 1/2" Beaded Tube, Made in the USA and manufactured to exact OEM specifications, Additional Handling and Oversize Fees Apply To This Item, (Item #: 156372)$2639.01
Steering
Differential Pinion Bearing - Used on mechanical four wheel drive front ends, this open roller bearing measures 1.42 inches inside diameter, 2.28 inches outside diameter and 0.78 inches wide. Replaces OEM numbers International Harvester - 81326C1, Ford/New Holland - 83934020, E2NN1N055AA, John Deere - AL39377, JD10250 (Item #: 112468, Ref: VPJ2550)$42.00
Hydrostatic Steering Cylinder Kit - For John Deere Construction and industrial models 310C, 510B, 515B, Replaces John Deere OEM number AT78498, AT76043, (Item #: 159181)$43.00
Planetary Gear - For the following John Deere applications: 2140 with ZF APL735 Axle, 2750 with ZF APL735, 2850, 2755, 210C up to serial number 796033, 300D up to serial number 796033, 310C serial number 737488 and up, 310D up to serial number 796033, 315D up to serial number 796033, 482C up to serial number 796033. This part replaces John Deere part numbers L60111 and T116830 (Item #: 180655, Ref: L60111)$95.00
Tie Rod, RH Thread, 4WD - This Tie Rod is 8.250 inches long. It has - M22 X 1.5 R/H Threads on one side and - M24 X 1.5 R/H Threads on the other. It is used on John Deere 2140, 2750, 2950, 3040, 3050, 3140, 3350, 210C, 300D, 310C, 310D, 315C, 315D, 410C, 410D, 482C, 510C, 510D, 610C. It Replaces AL60161, AL39316, AL178074, AL55011 (Item #: 104855, Ref: N14377)$54.00
Universal Parts and Accessories Category: Accessories / Supplies
Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127)$388.00
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153)$100.55
Decals and Emblems
2 Legged Deer Decal - John Deere Leaping 2-Legged Deer, 3 1/2" x 4" black and silver, vinyl cut. (Item #: 183241, Ref: R4697)$7.70
2 Legged Deer Decal - John Deere Leaping 2 Legged Deer, 2 1/2" x 3", black and yellow, vinyl cut. (Item #: 183158, Ref: R4696)$7.70
No Picture
2 Legged Deer Decal - John Deere leaping 2 legged deer, 6" black with yellow deer on vinyl. (Item #: 183582, Ref: R5186)$22.70
2 Legged Deer Decal - John Deere leaping 2 legged deer, 6" yellow with black deer on vinyl. (Item #: 183188, Ref: R5187)$14.80
4 Legged Deer Decal - Says "John Deere Quality Farm Equipment + Parts and Service" with leaping 4 legged deer, 10" on vinyl. (Item #: 183604, Ref: R5185)$41.00
Loader Decal, Yellow - Universal John Deere loader decal, 2" x 24". (Item #: 173325, Ref: JDL2Y)$24.50
Electrical System
NOTE
Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.
NOTE
No Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE)$88.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209)$13.40
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302)$25.20
No Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010)$54.00
Magneto Cap, 2 Cylinder - For tractor models using WICO XH magneto ONLY. (Item #: 105667, Ref: 1006501)$57.00
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6)$24.70
No Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85)$5.40
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425)$4.50
NOTE
Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!
NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6)$15.70
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12)$15.70
Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR)$10.60
Engine Parts
NOTE
Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).
NOTE
Engine Rings
NOTE
Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").
NOTE
Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C)$77.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C)$105.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C)$123.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR)$108.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR)$167.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C)$150.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C)$170.00
Chrome Exhaust System - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR)$89.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114)$3.30
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134)$4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138)$2.80
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214)$4.58
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234)$8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300)$7.00
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312)$7.40
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400)$8.40
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500)$14.30
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799)$10.30
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800)$9.00
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802)$11.60
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804)$11.40
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807)$11.00
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14)$14.30
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15)$18.38
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A)$6.70
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A)$7.50
Fuel System / Air Intake
Carburetor Elbow and Strainer - Fits various JD models. VERIFY FITTING DIMENSTIONS. Fits Marvel and some Carter UT Series carburetors. Used with flair fitting, not compression fitting. Male end (screen end) is 1/8 inch pipe threads. Female end is 1/4 inch flair. (Item #: 110005, Ref: 9N9553)$5.50
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949)$9.40
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R)$3.90
Gauges
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771)$58.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672)$41.00
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095)$14.90
Hitch / Drawbar
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inches), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X)$11.50
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2)$37.00
Hydraulic System
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021)$15.20
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12)$11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180)$55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24)$13.50
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30)$16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48)$16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000)$15.80
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60)$15.80
Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317)$15.50
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inches to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269)$242.80
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269)$242.80
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215)$120.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH)$39.00
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311)$51.00
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH)$54.00
No Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP)$21.50
Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236)$384.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B)$245.00
Tractor Umbrella with Frame & Mounting Bracket - Yellow - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, Additional Handling & Oversize Fees Apply To This Item, (Item #: 161195)$122.00
Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250)$24.00
No Picture
Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_)$8.50
No Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP)$8.50
No Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL)$70.00
No Picture
Paint, Clear Coat, 1 Quart - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT)$30.20
No Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL)$56.00
No Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT)$23.60
No Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP)$8.70
No Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT)$23.00
No Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP)$8.70
No Picture
Paint, Green, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108349, Ref: TP210GAL)$76.00
No Picture
Paint, Green, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108348, Ref: TP210QT)$29.50
No Picture
Paint, Green, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108347, Ref: TP210SP)$10.30
No Picture
Paint, Industrial Yellow, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108346, Ref: TP530GAL)$110.00
No Picture
Paint, Industrial Yellow, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108345, Ref: TP530QT)$40.00
No Picture
Paint, Industrial Yellow, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108344, Ref: TP530SP)$10.50
No Picture
Paint, JD Yellow, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102411, Ref: TP190GAL)$60.00
No Picture
Paint, JD Yellow, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102410, Ref: TP190QT)$23.30
No Picture
Paint, JD Yellow, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102409, Ref: TP190SP)$8.00
No Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL)$60.00
No Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT)$23.50
No Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT)$17.00
No Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP)$7.90
No Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL)$84.67
No Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL)$68.39
No Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT)$99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R)$45.00
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R)$45.00
PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY)$176.91
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33)$339.00
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164)$264.00
Seats
Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. (Item #: TS5056V)$1518.86
Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056)$2161.57
Tie-On Seat Cover - Yellow and Green, 19 inches wide. Deluxe with 2 inches of foam. Fits only tractors that use a PAN type seat. (Item #: 179179, Ref: R2602)$52.00
Tie-On Seat Cover - Yellow and White, 21 wide. Deluxe with 2 inches of foam. For tractors that use a PAN SEAT only. (Item #: 179810, Ref: R1014)$46.00
Tie-On Seat Cover - Green and White, 21" wide. Deluxe with 2 inches of foam. Fits only tractors that use a PAN type seat. (Item #: 179516, Ref: R1016)$52.00
Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP)$100.00
Sheet Metal / Body Parts
Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140)$41.19
Fender Hand Grip - Used on many ag tractors, combines, implements and industrial tractor applications. (Item #: 103959, Ref: R20759)$9.00
Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K)$178.00
Steering
Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003)$410.00
Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: PMLF614 (Item #: 111126, Ref: AE33538A)$12.30
Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417)$49.00
Tools
No Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891)$24.30
Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. Replaces: JD1293, JD3039 (Item #: 103768, Ref: FW60166)$97.00
Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. (Item #: 116854, Ref: FW55166)$69.00
Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB)$17.15
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R)$45.00
Tire, Three Rib - Front tire, 3 Rib, 5.50 inch x 16 inch. Designed to be used with tube (part number WHS050). 6 Ply.Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16)$109.00
Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050)$17.90
No Picture
Tire Tube 24 Inch - This 24 inch tire tube is used for all tractors with the following tires: 10.00 x 24, 11.00 x 24, 11.2 x 24, and 12.4 x 24. (Item #: 178957, Ref: WHS059)$56.00
No Picture
Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058)$63.00
No Picture
Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 12.00 x 28, 13.00 x 28, 13.6 x 28, and 14.9 x 28. (Item #: 178895, Ref: WHS061)$116.00
No Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062)$66.00
YESTERDAY's TRACTORS
has been a leading tractor parts supplier on
the internet since 1995. Join thousands of happy customers
who have purchased parts and more for their antique tractor from us!
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
