FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

John Deere MC Tractor Parts

[Categories] [All John Deere Models] [Print]

Clutch

Clutch Kit, 10 Inch - This new single stage clutch kit includes a new pressure plate, a 10 inch, 10 spline, 1 3/8 inch hub, woven clutch disc. The release bearing (N1087), has an outside diameter of 3.500 inches, and inside diameter of 2.062 inches, and a thickness of .750 inches. This kit has two pilot bearings and two alignment tools (not shown) to accommodate different flywheels. The first pilot bearing (6202-2RS), has an outside diameter of 1.375 inches, and inside diameter of .590 inches, and a thickness of .470 inches. The second pilot bearing (6203-2RS), has an outside diameter of 1.574 inches, and inside diameter of .669 inches, and a thickness of .470. Used on tractors M, MI, MT, 320, 330, 435, 40, 420, 430, 440, MC. Replaces AM2575T, AM2576T, AM3983T (Item #: 173360, Ref: R2576NKIT) $190.00

Pressure Plate - 10", 3 lever. For tractor models G, M, MT, 105, 3300, 320, 330, 40, 45, 55, 95, 40C, (420, 430, SN# 99999 and below), 440. Replaces: AM227T, AM2576T, AM650T . (Item #: 162165, Ref: AM2576T) $132.00

Cooling System

No
Picture
Fan Belt - For model M. 3/4" X 34.53" (sub. for AM631T) (Item #: 114500, Ref: M266T) $25.10

Lower Radiator Bracket - For John Deere tractor models M, MC, MT, 40, 320, 330, 420, 430, Replaces John Deere OEM number AM298T, This bracket does NOT include the rubber mounting pad, (Item #: 126573) $27.80

$John Deere MC Radiator Hose - Bulk 3' x 2-1\4$
Radiator Hose - Bulk 3' x 2-1/4 - For John Deere tractor models M, MC, MT, 40, 320, 330, 2510, 2520, 3010, 3020, 4000, 4010, 4020, 4320, 4520, 4620, 5010, 8440, 8640, Compatible with John Deere Combine (s) 45, 55, 65, Replaces John Deere OEM number R26294, H31009, M263T, H24921, L4577T, N71260, P43392, R26531, R32653, RN268FN, T13149, T209T, Replaces Case IH OEM number 407010R1, I.D. (A): 2-1/4", O.D.: 2-5/8", Length: 3', For Hose Clamp use Item #: 130455, (Item #: 150819) $27.90

Radiator Hose - Lower - For John Deere tractor models M, MC, MT, 40, 320, 330, Replaces John Deere OEM number L4576T, 2" I.D., 2-5/16" O.D., 2-11/16" Long, 2 Used per tractor, For Hose Clamp use Item #: 130455, (Item #: 114599) $5.90

Drive Train

Gear Shift, Direction Reverse Knob - Also used on Touch-O-Matic, remote control, and hydraulic knobs. Plastic Knob, 3/8 inch fine thread. For tractor models M, MC, MT, 40, 320, (420 up to serial number 125000), 1010. (Item #: 126604, Ref: R4572) $6.00

Gear Shift Lever Washer And Snap Ring Kit - Retains the gear shift lever into the housing. Measures: 0.254 inches thick, 1.368 inch outside diameter and 0.998 inch inside diameter. L, LA, LI, M, MC, MI, MT, MTN, MTW, 1010, 1020, 1030, 1035, 1040, 1120, 1130, 1140, 1350, 1520, 1530, 1550, 1630, 1635, 1640, 1641, 1750, 1830, 1840, 1850, 1950, 2020, 2030, 2035, 2040, 210C, 2120, 2130, 2135, 2141, 2150, 2155, 2240, 2250, 2251, 2255, 2350, 2351, 2355, 2440, 2450, 2541, 2550, 2555, 2630, 2640, 2650, 2651, 2750, 2755, 2840, 2850, 2855, 2940, 2941, 2950, 2951, 2955, 300B, 300D, 301A, 302A, 3030, 3040, 3050, 310A, 310B, 310C, 310D, 3120, 3130, 3135, 3140, 3141, 3150, 315C, 315CH, 315D, 320, 330, 3340, 3350, 3351, 350B, 350C, 350D, 355D, 3641, 3651, 40, 401B, 401C, 401D, 410B, 410C, 410D, 415B, 420, 430, 435, 440, 480A, 480B, 480C, 510B, 510C, 510D, 515B, 610B, 610C, 710B, 710C, [820 3 cylinder, 830 3 cylinder, 840 (3 cylinder)], 920, 930, 940, 940V, Industrial: 300, 301, 302, 310, 350, 380, 400, 401, 410, 480. Replaces: L4027, L4035. (Item #: 129237, Ref: 70202875) $15.60

Transmission Input Quill Seal - This transmission input quill seal has a 1.125 inch Inside Diameter, a 2.004 inch Outside Diameter and is 0.250 inch wide. It Fits: M, MC, MI, MT, MTN, MTW, 320, 330, 40, 420, 430. Replaces: AL2122T, AL2653T, AR608R (Item #: 106846, Ref: AL2122T) $7.70

Electrical System

Distributor Dust Cover - Fits early Delco Distributor with Clip Held Cap. For tractor models A, AR, AH, AN, ANH, AO, B, BR, BN, BNH, BW, BWH, G, GN, GW, M, MC, MI, MT, 40, 50, 60, 70, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010, 2010, 3010, 4010. (Item #: 103153, Ref: 1900119) $9.00

Distributor Hold Down Clamp - This Distributor Hold Down Clamp is serviceable, but not like the original on John Deere M, MC, MI, MT, 1010, 2010, 320, 330, 40, 420, 430, 440. Will replace John Deere part number M415T. (Item #: 182464, Ref: 341139R1) $9.20

Distributor Shaft Bushing and Shim Kit - Delco Distributor Shaft Bushing and Shim Kit. Fits M, MC, MI, MT, 320, 330, 40, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010, 2010, 3010 with one of the following Delco distributors: 1112623, 1112623, 1112577, 1112648, 1112581, 1111418. Replaces: washer: 811912, shim washer: 810074, 810078, bushing: 1909003, 1952334 (Item #: 178103, Ref: ABC3007) $29.50

Distributor Terminal Insulator Assembly, Delco - This Delco Distributor Terminal Insulator Assembly is for Round Shoulder (outside terminal). Note: As distributors can be changed over time, it is best to double check which style you require. This is only a guide of what was original. Fits distributor housings with 0.345 inch diameter round hole. If not sure, measure before ordering. Used on M, MC, MI, MT, 320, 330, 40; Replaces: 810794, 817363, 1847646, 1847647, 1878405 (Item #: 111459, Ref: 1878405ASSY) $15.00

Generator - Delco Style (9276), Remanufactured, Delco Remy, 1101852 - For John Deere tractor models M, MC, MT, Replaces Delco Remy manufacturer number 1101852, 1101857, 1101860, Replaces manufacturer number 9276, 340-32, 92-01-3066, Delco Style, Voltage: 6, PULLEY NOT INCLUDED, Rotation: Clockwise, Amperage: 12, (Item #: 203517) $420.01

$John Deere MC Ignition\Light Switch$
Ignition/Light Switch - 5 terminal, uses A4653R lever. For tractor models 320, (M, MC, MI, MT all with regulator), 40, (50 up to SN# 5021479), (60 gas up to SN# 6025999, STD gas up to SN# 604299, and Orchard), (70 gas), 330, 420, 430, 435, 440, (620 Orchard from SN# 6223000 and up). Replaces AA5071R. (Item #: 108163, Ref: AM1866T) $35.00

$John Deere MC Ignition\Light Switch, 5 Position$
Ignition/Light Switch, 5 Position - With Lever. For Tractors with Cutout For tractor models M, MC, MI, MT. Replaces AM812T, AM357T (Item #: 126168, Ref: R5385) $104.00

Rotor - Used with Delco distributors with a clip held cap. For tractor models: A, AO, AR, B, D, G, M, MC, MT, 320, 330, 40, 420, 430, 50, 520, 530, 60, 620, 630, 70, 720, 730, 1010 (1112577), 2010 (1112577), 3010 (1112577), 3020 (up to serial number 58899 and 1112577), 4010 (up to serial number 39499 and 1112581). Replaces 1905590. (Item #: 110177, Ref: 1750498M1) $3.60

Rubber Grommet - For John Deere tractor models H, M, MC, MT, R, 50, 60, 70, 520, 530, 620, 630, 720, 730, 1350, 1530, 2240, 2440, 2510, 2630, 2640, 3020, 4000, 4020, 4030, 4230, 4320, 4430, 4520, 4620, 4630, 5020, 6030, 8430, 8630, Replaces John Deere OEM number H987R, M305T, Can be used for hole in spark plug cover, fuel tank pads and electric wire grommet, (Item #: 126661) $1.80

Spark Plug - Replaces Autolite AL216, AL7, AL295 and Champion H10, H10C, H10J, H11, H12, H8, H8J, RH10, RH12, RH8 spark plugs. For tractor models 320, 330, 420, 430, 820, 830. Price is for 1 plug. If you need 4, you need to order 4. Verify correct spark plug size and type (Item #: 111743, Ref: AL295) $4.00

Starter Knob - Plastic. For tractor models 320, M, MC, MT, 40, 330, 420, 430, 440. (Item #: 179543, Ref: M2544T) $8.00

Starter Switch - For tractor models A up to serial number 502231, AO up to serial number 272000, AR up to serial number 272000, B up to serial number 200999), H, L, LA, M, MC, MT, R, 320, 330, 40, 420, 430, 440, 50, 60. Replaces: 1882323, AT21265. (Item #: 105669, Ref: 1925781) $9.00

V Belt - Belt is 1/2 inch wide and 23-1/4 inches long.Used on L (Styled SN# L640000 and up), LA, M, MC, and MT. Replaces L4201T. (Item #: 115938, Ref: 107671C1) $2.30

Voltage Regulator Conversion Kit - Used with VR1813 and VR1814 regulators when replacing Delco Cutouts 1116766, 1116807, 1116809 and 1116816 or control units 5839, 5851 and 5894, therefore modernizing Generator System. A, AO, AR, B, BO, BR, G, H, L, LA, M, MC, MI, MT (Item #: 184930, Ref: VRK1815) $64.00

Wiring Harness - For John Deere tractor models M, MC, MT (all with cut-out relay), For 6 volt generator systems only with cut-out relays, Cotton braided - exactly like original, Includes headlight wires and wiring instructions, All terminals are soldered and sealed, (Item #: 126799) $285.01

Engine Gaskets

Front Crankshaft Seal - This front crankshaft seal has a 1.125 inch Inside Diameter, a 2.004 inch Outside Diameter and is 0.250 inch wide. It Fits: L, LA, LI, M, MC, MI, MT, MTN, MTW, 320, 330, 40, 420, 430, 440. Replaces: AL2122T, AL2653T, AR608R (Item #: 106846, Ref: AL2122T) $7.70

Rear Crankshaft Seal - This rear crankshaft seal has a 4 inch Inside Diameter, a 5.004 inch Outside Diameter and is 0.312 inch wide. It Fits: L, LA, LI, M, MC, MI, MT, MTN, MTW, 320, 330, 40, 420, 430, 440. Replaces: AM220T, AM727T (Item #: 106852, Ref: AM220T) $21.10

Engine Rebuild Kits

Engine Rebuild Kit - Less Bearings - 2.250" Rod Journals, 100 - For John Deere tractor models M, MC, MT, 320 (s/n 320854-earlier), Compatible with John Deere Engine (s) 100 (gas), Bore: 4.000", Vertical 2 cylinder engine, 2.250" rod journal diameter, Kit includes: Pistons, Piston Ring Set, Connecting Rod Bushings, and Gasket set with Crank Seals, Kit does not include connecting rod or main bearings, For standard connecting rod bearing use Item #: 106780, (Item #: 130644) $665.00

Engine Parts

Push Rod - Used on John Deere 2 Cylinder engines on M, MI, MT, 320, MC, 40, 330, this push rod is 11.125 inches overall length and 0.315 inches in diameter. This part replaces John Deere part number M30T (Item #: 184634, Ref: M30T) $40.50

Valve Spring - For John Deere tractor models M, MC, MT, 40, 320, 330, 420, 430, 440, Compatible with John Deere Engine (s) 100 (2 cylinder gas), 113 (2 cylinder gas), Replaces John Deere OEM number M102T, 212-1096, (Item #: 128580) $0.98

Engine Rings

Piston Ring Set - .045" Oversize - 2 Cylinder - For John Deere tractor models M, MC, MT, 40, 320, 330, Compatible with John Deere Engine (s) 100 (gas), This is a custom made set that requires a 4 week lead time, Standard Bore: 4.000", Ring Size: .045" Oversize, Compression Rings per Piston: (3) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .094", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .250", 4th Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a complete 2 cylinder set, For standard use Item #: 129151, (Item #: 129149) $125.00

Piston Ring Set - .090" Oversize - 2 Cylinder - For John Deere tractor models M, MC, MT, 40, 320, 330, Compatible with John Deere Engine (s) 100 (gas), This is a custom made set that requires a 4 week lead time, Standard Bore: 4.000", Ring Size: .090" Oversize, Compression Rings per Piston: (3) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .094", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .250", 4th Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a complete 2 cylinder set, For standard use Item #: 129151, (Item #: 129150) $109.00

Piston Ring Set, 100 CID Gas - RING SET For 4.000" bore pistons, each piston uses: (2) 5/32" compression and (1) 1/8" compression ring and (1)1/4" oil ring. This ring set covers TWO CYLINDERS. Fits 40, 40 crawler, M, MC, MI, MT. NOTE: Do not order by tractor model only. Due to the many different piston manufacturers, there can be as many as 8 different ring sets available for one particular engine. To ensure you order the correct rings, we will need the following information: 1.) bore size, 2.) thickness of each ring, 3.) how many of each ring thickness per piston. (Item #: 130055, Ref: 2C7771) $72.00

No
Picture
Piston Ring Set - .120" Oversize - 2 Cylinder - For John Deere tractor models M, MC, MT, 40, 320, 330, Compatible with John Deere Engine (s) 100 (gas), This is a custom made set that requires a 4 week lead time, Standard Bore: 4.000", Ring Size: .120" Oversize, Compression Rings per Piston: (3) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .094", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .250", 4th Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a complete 2 cylinder set, For standard use Item #: 129150, (Item #: 129151) $125.00

Piston Ring Set - Standard - 2 Cylinder - For John Deere tractor models M, MC, MT, 40, 320, 330, Compatible with John Deere Engine (s) 100 (gas), This is a custom made set that requires a 4 week lead time, Bore: 4.000", Ring Size: Standard, Compression Rings per Piston: (3) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .094", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .250", 4th Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a complete 2 cylinder set, For .040" use Item #: 129151, (Item #: 130006) $104.00

Exhaust System

Chrome Curved Exhaust Stack - For M, MC, MT, 40, 320.Chrome Curved Exhaust Stack With 2 Bolt Flange. 3 inches O.D. For Body, 18 inches Tall Chrome. 4 inches Tall at Base. Double Walled. (Item #: 179463, Ref: R4260) $210.01

Chrome Straight Exhaust Pipe - Double Wall, Length 18 inches plus a 4 inch base. For M, MT, MC, 40, 320. Chrome Straight Exhaust Pipe Double Walled with 2 Bolt Flange - 22" Tall - 3" OD. (Item #: 178976, Ref: R4259) $218.00

Maniflod - This is a perfect match for the original manifold on M, MI, MT, MC, 40. Other manifolds will work, but this one is built just like the original. This part replaces M408T, M1799T. If you need a gasket set, order part number R0309G. Note, this part may arrive as unpainted casting, not painted. (Item #: 101581, Ref: M1799T) $129.00

Manifold Heat Baffle - This new manifold heat baffle, used on M, MT, MC, MI, 320 and 40, is often missing from tractors. Many times, when the manifold was changed they removed this baffle and did not re-install it. If you want your tractor back to original, you'll need this. It comes complete as shown and will be shipped to you as bare steel, ready for your paint and installation. Replaces: AM315T (Item #: 179575, Ref: AM315T) $71.37

Muffler - Vertical and horizontal muffler~ round body, 2 bolt flange mount 1-7/8" O.D. 1-3/4" inlet I.D, 2" exhaust O.D, 21" overall length, 3-1/4" shell diameter. For tractor models (320, 330 1957-1959), (40 1953-1956), (M, MC, MT 1947-1952). Uses raincap Part # R1800. (Item #: 101172, Ref: AM364T) $55.00

Stainless Steel Muffler - For John Deere tractor models M, MC, MT, 40, 320, 420, Replaces John Deere OEM number AM3101T, AM364T, AM625T, Polished Stainless Steel (Extreme heat can cause discolorations), Inlet Length: 2-1/4', Inlet OD: 1.905", Shell Length: 14-1/2", Shell Diameter: 3-1/4", Outlet Length: 3-1/2", Outlet OD: 1.660", Overall Length: 20-1/2", (Item #: 164547) $129.00

Fuel System / Air Intake

Adjustable Needle Assembly - 3/8 inch x 24 thread. Main Adjusting Needle. For tractor models: M, MC, MT, 40, 420, 430 with one of the following Marvel carbs TSX181, TSX221, TSX245, TSX332, TSX374, TSX397, TSX413, TSX436, TSX505, TSX526, TSX530, TSX641, TSX662, TSX688, TSX689, TSX695, TSX756, TSX768, TSX769, TSX772, TSX774, TSX775, TSX777, TSX784, TSX792, TSX801, TSX811, TSX813, TSX816, TSX97. (Item #: 108463, Ref: C3NN9G504A) $25.90

Air Cleaner Cap - For Model. M, MC, MT, 40, 320, 330, 420, 430, 1010. 1.950 pipe outside diameter. Replaces AM467T. (Item #: 126368, Ref: AM371T) $40.00

Air Cleaner Oil Cup - Cup is 5 3/4 inches O.D. at the lip. Fits B SN# 60000 and up, BR-BO SN# 329302 and up, H, 50, 520 and 530. For clamp style air cleaners, not clip style. Replaces 1001012M91, 10P1146, 10P931, 1754014M1, 1K-6054, 1K-6054, 311510, 362974R91, 375550R91, 378333R1, 52864DA, AB1626R, AB3477R, AM3172T, AM465T, AM468T, AT10592, G46325 (Item #: 108775, Ref: AB1626R) $32.60

Cable Clip for Marvel Schebler Carburetors - Many Marvel Schelber Carburetors use one of these clips to secure the choke or the fuel cable. On John Deere, it is used on the following Carburetors TSX85, TSX89, TSX245, TSX356, TSX475, TSX485, TSX491, TSX530, TSX615, TSX688, TSX756, TSX759, TSX777, TSX788, TSX802, TSX805, TSX806, TSX808, TSX809, TSX810, TSX812, TSX823, TSX860, TSX881, TSX883, TSX885, TSX888, TSX892, TSX894, TSX895, TSX898, TSX904, TSX904SL, TSX905, TSX905SL, TSX906, TSX907, TSX908, TSX908SL, TSX923SL, TSX941SL, TSX944, TSX945SL, TSX952SL, TSX953SL, TSXU838, TSXU1007, USX20, USX21, USX30, USX31, USX35, USX36, USX48SL, USX49SL, USX211. These carburetors are possible on John Deere Models: M, 600, MI, MT, 320, L, 500, LA, MC, 40, 330, 420, 430, 24, 1010, 1020, 1520, 2010, 2020, 2030, 2510, 2520, 4030, 500A, 500B, 440A, LI, 440B, 99 Replaces: E10058, R10188 (Item #: 126116, Ref: CT29-81) $5.10

Carburetor - New carburetor with reversible linkage. For M, MC, MT (VD Engine serial number 1000up), 40, 77 Crawler, 300 (135G), 320, 330, 350 Crawler, 1020, 2010, 2020, 2500, 2510, Combines 45 (HA145, HA165D, 145GH, 180G4H Engine), 55 (HA217 gas), 95 (303G5H, 303G6H), 8x6 and 99 Cotton Pickers, NA217, 135 G Sprayer. Replaces Marvel -Schebler numbers TSX245, TSX475, TSX530, TSX562, TSX615, TSX641, TSX678, TSX688, TSX689, TSX704, TSX711, TSX737, TSX756, TSX768, TSX808, TSX810, TSX819, TSX877, TSX881, TSX883, TSX885, TSX888, TSX892, TSX894, TSX895, TSX898, TSX899, TSX904, TSX904SL, TSX905, TSX905SL, TSX906, TSX906SL, TSX907, TSX908, TSX920, TSX921, TSX922, TSX923, TSX938, TSX939, TSX941, TSX959. Center to center on the 2 mounting bolts is 2 11/16 inches. (Item #: 100752, Ref: 14996) $465.00

Carburetor - This New Carburetor is the Original Marvel-Schebler Design. It Replaces carburetor numbers TSX245 and TSX530. It will also replace TSX475 and TSX562 all-fuel / distillate carburetors when converted to run on gasoline. 2-11/16 Inch center-to-center mounting bolt spacing. Used on John Deere M, MC, MI, MT, MTN, MTW, 320, 320S, 320U, 320V, 330, 330S, 330U, 330V, 40, 40C, 40H, 40S, 40T, 40U, 40V, 40W Replaces John Deere part numbers: AM1794T, AM366T, RE19402, Replaces all fuel when converted to gas: AM1613T, AM2067T. (Item #: 185127, Ref: TSX530) $390.00

Carburetor - This New Zenith Style Carburetor with reversible linkage. Replaces TSX245, TSX475, TSX530, TSX562, TSX615, TSX641, TSX678, TSX688, TSX689, TSX704, TSX711, TSX737, TSX756, TSX768, TSX808, TSX810, TSX819, TSX877, TSX881, TSX883, TSX885, TSX888, TSX892, TSX894, TSX895, TSX898, TSX899, TSX904, TSX904SL, TSX905, TSX905SL, TSX906, TSX906SL, TSX907, TSX908, TSX920, TSX921, TSX922, TSX923, TSX938, TSX939, TSX941, TSX945, TSX945SL, TSX959, TSXU963, TSXU9631. John Deere Part Numbers AM1613T, AM1794T, AM2067T, AM3061T, AM3227T, AM3611T, AM3611T, AM3612T, AM3612T, AM366T, AM771T, AR62244, AR67706, AT10181, AT10428, AT10576, AT11158, AT11637, AT11680, AT12357, AT13064, AT14028, AT14047, AT14095, AT14387, AT17374, AT17629, AT18036, AT18098, AT18110, AT21142, AT21183, AT21184, AT21185, AT21358, AT21411, AT21786, AT21848, AT22994, AT22997, AT23000, AT23013, AT23016, AT23132, AT23136, AT23264, AT26120, AT27783, AT359T, AT420T, AT453T, RE19402. Center to center on the 2 mounting bolts is 2 11/16 inches. (Item #: 183805, Ref: 14996B) $310.00

Carburetor Float - For tractor models M, MC, MT, 40, 320, 330, 420, 430, 440, 1020, 1520, 2010, 2020, 2030, 2510, 2520. All with Marvel-Schebler Carburetors: TSX245, TSX475, TSX530, TSX562, TSX641, TSX678, TSX688, TSX756, TSX808, TSX810, TSX899, TSX904, TSX904SL, TSX905, TSX905-1, TSX944SL, TSX945SL, TSXU963. Replaces OEM 30-739. (Item #: 105095, Ref: R2383) $19.50

Carburetor Kit - For John Deere tractor models M, MC, MT, 40, 320, Replaces Marvel Schebler manufacturer number MSCK49, (Item #: 181519) $36.50

Carburetor Kit, Complete - This Complete Carburetor Kit is for Marvel-Schebler carburetor number TSX562 (Must Reuse Nozzle) Includes Basic Kit, plus Fuel and Air Adjusting Screws and Jets. (Item #: 185575, Ref: R7902) $47.70

Carburetor Kit, Comprehensive - This comprehensive carburetor kit is for Marvel-Schebler # TSX245. For John Deere 320, 330, M, MC and MT tractors. The kit contains all the parts shown. (Item #: 182524, Ref: R7897) $68.00

Carburetor Kit, Comprehensive - This comprehensive carburetor kit is for Marvel-Schebler # TSX475. For John Deere model 320, 330, M, MC and MT tractors. The kit contains all the parts shown. (Item #: 131600, Ref: R7899) $63.00

Carburetor Kit, Comprehensive - This comprehensive carburetor kit is for Marvel-Schebler # TSX530. For John Deere model 40, M, MC and MT tractors. The kit contains all the parts shown. (Item #: 182526, Ref: R7901) $61.00

Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: TSX245, TSX475, TSX530. For the following tractor models: M, MC, MT, 40, 300, 320. Add $100.00 core charge to price and you will receive instructions for returning your core for a refund if you have one available. (Item #: 203277, Ref: 1516-CARB) $255.01

Carburetor Repair Kit - Basic carburetor repair kit contains needle float valve, float lever shaft and gasket set. Available with VITON needle float valve. Carburetor manufacture numbers: TSX245, TSX475, TSX530. On models: 320, 40, M, MC, MT. (Item #: 112440, Ref: BK39V) $34.00

Choke Cable - Total Length 47" (replaces AT13452, AM1799T, AT12896), Fits, 1010, 2010, 320, 330, 40, M, MC, MT. (Item #: 121224, Ref: AT21782) $25.70

Fuel Sediment Bowl Bail Assembly - This bail fits 1.280 inch tall glass bowls. It is 2.700 inches in length. Replaces OEM numbers: 0W446, 1001515M91, 15P15, 1JS-5305, 223247, 2N9166, 49947DX, 70223247, A11212 (Item #: 113631, Ref: 2N9166) $3.00

Fuel Sediment Bowl Gasket - Gasket, Sediment Bowl. 2 inch outside diameter. This gasket may come with a bonus screen that may not work for your particular tractor. Used on Case Tractors with 2 inch outside diameter sediment bowls. Replaces original part number L886T. Gasket may be cork or rubber, depending on availability. (Item #: 105383, Ref: 2NAA916061) $2.60

Fuel Sediment Glass Bowl - 2 inch glass bowl with a length of 1.280 inches. Uses gasket NAA9160A, not included. For the following models: L, LA, M, MC, MT, 320, 330, 40, 420, 430, 1010. Replaces M3340T . (Item #: 105382, Ref: 9N9162) $3.20

Needle Valve - Viton Float Valve Needle, Seat and Gasket Assembly for some Marvel Schebler carburetors. For the following models: M, MC, MT, 320, 330, 40, 420, 430, 50, 520, 530, 60, 620, 630, 70, 720, 730, 2010. Replaces 233-543. (Item #: 179751, Ref: C3NN9D532A) $6.50

Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. Replaces: L885T (Item #: 105364, Ref: 49923D) $3.30

Throttle Handle - For Model: MC. Replaces AM1041T (Item #: 179898, Ref: M1063T) $76.44

Hydraulic System

Hydraulic Block-Off (Dummy Plug) - Fits all with locking nut style coupler. Measures 0.685 inches outside diameter, 5.377 inches overall length, For locking nut style coupler. Note: Fits PowerTrol SN # PCV-100 to 67904. Only fits early serial numbers. Later serial numbers use AA4321R. This part replaces AA3762R, AA4980R (Item #: 178584, Ref: AA3762R) $57.14

Hydraulic Block Off Plug (Dummy Plug) - Used on Swinging style lever Powr-Trol Serial number PCV-67905 and up. This part has 1/2 inch pipe thread. This part replaces John Deere part numbers AA4981R, AA4321R (Item #: 178972, Ref: AA4321R) $48.60

Hydraulic Coupler - For John Deere tractor models A, ANH, AO, AR, AW, B, BN, BNH, BW, BWH, G, GH, GM, GN, GW, MC (s/n 36948-later), 40, 50, 60, 70, 320, 330, 420, 430, 435, 440, 1010 (s/n 42000-earlier), Replaces John Deere OEM number A3613R, AA5535R, Powr-Trol s/n PCV67905-later, Swing style lever coupler, Thread: 1/2" Pipe, (Item #: 126179) $45.65

Hydraulic Coupler and Cover - For John Deere tractor models A, ANH, AO, AR, AW, B, BN, BNH, BW, BWH, G, GH, GM, GN, GW, MC (s/n 36948-later), 40, 50, 60, 70, 320, 330, 420, 430, 435, 440, 1010 (s/n 42000-earlier), Replaces John Deere OEM number A3613R, A3614R, AA5535R, Powr-Trol s/n PCV67905-later, Swing style lever coupler, Thread: 1/2" Pipe, Includes: Cover and Coupler, (Item #: 110633) $76.00

Lights

Headlight Bracket - For tractor models 1010, M, MC, MI, MT, 40, 320, 330, 420, 430, 435, 440. (Item #: 126561, Ref: M646T) $38.00

Headlight Rod - For tractor models 1010, M, MC, MI, MT, 40, 320, 330, 420, 430, 435, 440. Replaces T11022T. (Item #: 179505, Ref: M647T) $27.44

Light Clamp - For tractor models M, MC, MT, 40, 320, 330, 420, 430, 435, (2010 crawler), 3010, 3020, MI. (Item #: 126557, Ref: M1482T) $9.30

No
Picture
Rear Light Rod Bracket - For tractor models MC, 40 Crawler, 420C, 430C. All with standard seat; no loaders. (Item #: 180697, Ref: M1406T) $52.00

Oil System

Engine Oil Pump Strainer Screen - Used on John Deere models M, MI, MT, 320, MC, 40, 330, 420, 430 this strainer replaces John Deere part numbers AM734T and AM230T. (Item #: 164420, Ref: AM230T) $29.60

Oil Fill Breather Cap - With clip, copper filter. 3 1/4 inches tall. For tractor models L, LA, LI, M, MC, MI, 40, 320, 330, 420, 430, 440 gas. Fits over 1 1/2 inch pipe. Exact of original, "OIL" stamped into top. (Item #: 107000, Ref: R4458) $42.00

No
Picture
Oil Plug Gasket, 10 Pack - For John Deere tractor models M, MC, MT, 40, 420, 430, 1010, 1020, 1520, 1530, 2010, 2020, 2030, 2040, 2150, 2155, 2240, 2255, 2440, 2510, 2520, 2640, 2750, 2755, 2840, 2855, 2940, 2950, 3150, 4555, 4650, 4850, 4955, Replaces John Deere OEM number R120247, (Item #: 176719) $5.30

Paint

No
Picture
Paint, Classic Green, 1 Gallon - Green Paint for 2 cylinders include models A, AO, AR, B, BO, BR, C, D, GP, P, G, L, LA, H, M, MT, MC, Y, 62, R, 40, 50, 60, 70, 80, 320, 420, 520, 620, 720, 820, 330, 430, 530, 630, 730, 830, 435, 440, 840. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102408, Ref: TP215GAL) $60.00

No
Picture
Paint, Classic Green, 1 Quart - Green Paint for 2 cylinders include models A, AO, AR, B, BO, BR, C, D, GP, P, G, L, LA, H, M, MT, MC, Y, 62, R, 40, 50, 60, 70, 80, 320, 420, 520, 620, 720, 820, 330, 430, 530, 630, 730, 830, 435, 440, 840. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102407, Ref: TP215QT) $23.30

No
Picture
Paint, Classic Green, Spray Can - Green Paint for 2 cylinders include models A, AO, AR, B, BO, BR, C, D, GP, P, G, L, LA, H, M, MT, MC, Y, 62, R, 40, 50, 60, 70, 80, 320, 420, 520, 620, 720, 820, 330, 430, 530, 630, 730, 830, 435, 440, 840. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108347, Ref: TP215SP) $10.50

PTO / Driveline

PTO Shaft Seal - This Seal has multiple applications for John Deere, including; PTO seal, differential brake pinion shaft seal, inner bearing housing seal, direction reverser seal, upper final drive outer pinion shaft seal, front wheel assist transfer box seal, and others. It measures 1.375 inch inside diameter, 2.130 inch outside diameter, and 0.437 inch wide. Verify measurements or OEM part number before ordering. Replaces 0511073, 1K1590, 1K1590, 224810, 230608, 241779, 340214, 35451D, 357970R91, 357976R91, 380184R91, 43509D, 43509DA, 511073, 527829R91, 60454D, 659124R91, 70224810, 70230608, 70241779, 70241D, 938294R91, 938294R92, AH14076, AL2094T, AL56820, AM253T, AN30648, AN32717, AP24021, K1590, K1590, M86688, N71730N, T22069 (Item #: 128541, Ref: 70241779) $7.70

Seats

Seat Frame Assembly - Assembly includes Frame, Back and Latch. Does not include Base or Base with Toolbox, Sold Seperatly. For tractor models M, MC, MI, MT. Also replaces AM476T, M1501T, M358T, M359T and M360T. (Item #: 116595, Ref: AM1945T) $350.72

Sheet Metal / Body Parts

No
Picture
Battery Box - For M, MT, MC. Battery Box includes Left Side with Winged Latch, Right Side with Toolbox and Bottom Tray. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 179464, Ref: R2526) $282.00

Battery Box, Left Side Wall, with Winged Latch - For tractor models M, MT, MC. Replaces AM957T. Needs right hand side and tray to complete box. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 179510, Ref: R2523) $100.00

Battery Box, Right Side Wall, with Toolbox - For tractor models M, MT, MC. Replaces AM358T. Needs left hand side and tray to complete box. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 179507, Ref: R2524) $128.00

Battery Tray - For tractor models M, MT, MC. Replaces AM394T. Needs right and left hand sides to complete box. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 109381, Ref: R2525) $80.00

No
Picture
Complete 3-Piece Battery Box Assembly - Consists of R2523, R2524, R2525. For tractor models M, MT, MC. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 179464, Ref: R2526) $282.00

Wing Fastener - For John Deere tractor models M, MC, MT, 40, 70, 320, 330, 420, 430, 720, 730, Replaces John Deere OEM number F2134R, M1896T, M316T, M397T, With Pin, Pin dimensions: .309" diameter, .713" long, (Item #: 111045) $21.30

Steering

No
Picture
Axle Shaft Bearing - For John Deere tractor models M (s/n 44475 - later), MC (s/n 13907 - later), MT (s/n 27913 - later), 40, 320, 330, 420, 430, 435, 440, 1010, 1020, 2010, 2030 (s/n 187300 - earlier), Compatible with John Deere Combine (s) 45 (s/n 3500 - earlier), Compatible with John Deere Harvester (s) 9900, 9910, Compatible with John Deere Construction and industrial models 300, 301, 310 (s/n 192065 - earlier), 350, 350B, 380 (s/n 192065 - earlier), 400, 401, 410 (s/n 192065 - earlier), 440, 440 (s/n 17057 - earlier), 440A, 440A (s/n 17057 - earlier), 440B, 440B (s/n 17057 - earlier), 450, 480, 480A (s/n 193099 - earlier), 480B (s/n 193099 - earlier), 540, 540A, 540B, 540D, 548D, 640, 640D, 648D, Replaces John Deere OEM number JD8511, AL28037, Replaces Bearing number 7109, (Item #: 173783) $18.10

Steering Clutch Disc, Fiber - Disc is 8.554 inches O.D. 26 Internal Teeth. (Item #: 112073, Ref: M3293T) $28.10

Steering Clutch Disc, Steel - Disc is 9.268 inches O.D., 6.380 inches I.D. 6 External Ears. (Item #: 127279, Ref: M872T) $26.70

Steering Clutch Pressure Plate - 8.5", 3 lever. For tractor models 1010, 40C, 420, 420 Crawler, 430 Crawler, 440, 440D, MC. Replaces AT11853, AM1930T, AT11486, AM987T, AP23494. (Item #: 173463, Ref: AT16121) $262.00

Steering Wheel Nut - For John Deere tractor models H, HWH, M, MC, MT, 40, 320 (s/n 325000-earlier), 420 (s/n 124999-earlier), Replaces John Deere OEM number 14H398, AL2315, 5/8" - 18 NF Thread, .550" Tall, (Item #: 126724) $4.00

Tied Rod Tube - 12.620" long, .875" O.D. For tractor models M, MC, MT, 1010, 320, 330, 40, 430 all with adjustable axles. (Item #: 104819, Ref: AM2795T) $115.00

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $365.01

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $101.57

Decals and Emblems

2 Legged Deer Decal - John Deere Leaping 2-Legged Deer, 3 1/2" x 4" black and silver, vinyl cut. (Item #: 183241, Ref: R4697) $7.70

2 Legged Deer Decal - John Deere Leaping 2 Legged Deer, 2 1/2" x 3", black and yellow, vinyl cut. (Item #: 183158, Ref: R4696) $7.70

No
Picture
2 Legged Deer Decal - John Deere leaping 2 legged deer, 6" black with yellow deer on vinyl. (Item #: 183582, Ref: R5186) $22.90

2 Legged Deer Decal - John Deere leaping 2 legged deer, 6" yellow with black deer on vinyl. (Item #: 183188, Ref: R5187) $14.60

4 Legged Deer Decal - "John Deere Quality Farm Equipment" 10" on vinyl. (Item #: 183248, Ref: R5184) $39.90

No
Picture
4 Legged Deer Decal - Says "John Deere Quality Farm Equipment + Parts and Service" with leaping 4 legged deer, 10" on vinyl. (Item #: 183604, Ref: R5185) $39.90

Loader Decal, Yellow - Universal John Deere loader decal, 2" x 24". (Item #: 173325, Ref: JDL2Y) $24.10

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $94.00

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $13.50

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.90

Magneto Cap, 2 Cylinder - For tractor models using WICO XH magneto ONLY. (Item #: 105667, Ref: 1006501) $57.00

Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $24.70

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.20

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $15.80

$John Deere MC Tag for Starter\Generator, 12 Volt, Blank$
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $15.80

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.60

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $78.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $105.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $108.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $176.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $153.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00

Chrome Exhaust System - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00

$John Deere MC Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $3.10

$John Deere MC Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$John Deere MC Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.80

$John Deere MC Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $2.40

$John Deere MC Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.60

$John Deere MC Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $7.90

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $13.20

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.20

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $9.00

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $11.90

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40

Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $11.00

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60

Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $16.90

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $8.80

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $7.50

Fuel System / Air Intake

Carburetor Elbow and Strainer - Fits various JD models. VERIFY FITTING DIMENSTIONS. Fits Marvel and some Carter UT Series carburetors. Used with flair fitting, not compression fitting. Male end (screen end) is 1/8 inch pipe threads. Female end is 1/4 inch flair. (Item #: 110005, Ref: 9N9553) $5.50

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.10

$John Deere MC Sediment Bowl Gasket, 2-1\8 inch$
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.90

Gauges

Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $59.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $39.90

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $14.90

Hitch / Drawbar

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inches), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.28

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $14.70

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.21

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $15.60

Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $15.60

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $15.50

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.60

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inches to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $120.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.70

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.80

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $52.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $98.00

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $55.00

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.20

Miscellaneous

Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $390.00

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Tractor Umbrella with Frame & Mounting Bracket - Yellow - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, Additional Handling & Oversize Fees Apply To This Item, (Item #: 161195) $119.00

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.40

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.40

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $68.00

No
Picture
Paint, Clear Coat, 1 Quart - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.20

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $55.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $23.50

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $23.00

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.90

No
Picture
Paint, Green, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108349, Ref: TP210GAL) $76.00

No
Picture
Paint, Green, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108348, Ref: TP210QT) $29.50

No
Picture
Paint, Green, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108347, Ref: TP210SP) $10.50

No
Picture
Paint, Industrial Yellow, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108346, Ref: TP530GAL) $110.00

No
Picture
Paint, Industrial Yellow, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108345, Ref: TP530QT) $40.00

No
Picture
Paint, Industrial Yellow, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108344, Ref: TP530SP) $10.40

No
Picture
Paint, JD Yellow, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102411, Ref: TP190GAL) $59.00

No
Picture
Paint, JD Yellow, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102410, Ref: TP190QT) $22.70

No
Picture
Paint, JD Yellow, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102409, Ref: TP190SP) $8.00

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $60.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $23.30

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $16.90

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $7.90

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $44.10

PTO / Driveline

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $173.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $279.00

Seats

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. (Item #: TS5056V) $1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57

Tie-On Seat Cover - Yellow and Green, 19 inches wide. Deluxe with 2 inches of foam. Fits only tractors that use a PAN type seat. (Item #: 179179, Ref: R2602) $52.00

Tie-On Seat Cover - Yellow and White, 21 wide. Deluxe with 2 inches of foam. For tractors that use a PAN SEAT only. (Item #: 179810, Ref: R1014) $42.95

Tie-On Seat Cover - Green and White, 21" wide. Deluxe with 2 inches of foam. Fits only tractors that use a PAN type seat. (Item #: 179516, Ref: R1016) $49.57

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $103.00

Sheet Metal / Body Parts

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Fender Hand Grip - Used on many ag tractors, combines, implements and industrial tractor applications. (Item #: 103959, Ref: R20759) $9.00

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $178.00

Steering

Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003) $417.87

Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: PMLF614 (Item #: 111126, Ref: AE33538A) $12.60

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $48.40

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $24.30

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $307.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. Replaces: JD1293, JD3039 (Item #: 103768, Ref: FW60166) $92.00

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. (Item #: 116854, Ref: FW55166) $70.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire, Three Rib - Front tire, 3 Rib, 5.50 inch x 16 inch. Designed to be used with tube (part number WHS050). 6 Ply.Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16) $109.00

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $18.30

No
Picture
Tire Tube 24 Inch - This 24 inch tire tube is used for all tractors with the following tires: 10.00 x 24, 11.00 x 24, 11.2 x 24, and 12.4 x 24. (Item #: 178957, Ref: WHS059) $56.00

No
Picture
Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $64.00

No
Picture
Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 12.00 x 28, 13.00 x 28, 13.6 x 28, and 14.9 x 28. (Item #: 178895, Ref: WHS061) $116.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $66.00