TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

H cam gear broke

Welcome Guest, Log in or Register

Author

Norm

10-08-2003 17:29:46

Report to Moderator

I discover the cam gear and the pump gear broke on my H. Is there some play behind the cam gear or should it be tight. It seems like it will not line up if you tighten it all the way. Any help on the timing. I did this a while back but my memory is alittle short. Any other precautions. Thanks Norm

[Log in to Reply] [No Email]

Norm

10-08-2003 19:43:10

Report to Moderator

Re: H cam gear broke in reply to Norm, 10-08-2003 17:29:46

Aces

I found my problem. I must have been looking cross eyed at it. I found a pic in the past posts which expains everything. This sure is a helpful board. Thnks for your help. Now I just have to get a puller to remove the crank gear.

[Log in to Reply] [No Email]

Aces

10-08-2003 18:23:18

Report to Moderator

Re: H cam gear broke in reply to Norm, 10-08-2003 17:29:46

Very little play but needs to turn free. Just a hard plate with 2 cap screws to hold it to the block to hold the cam in place.

[Log in to Reply] [No Email]

Norm

10-08-2003 18:54:43

Report to Moderator

Re: Re: H cam gear broke in reply to Aces, 10-08-2003 18:23:18

Aces

It seems if you tighten it all the way the gear will hit the back plate. The hub should be out right. The back side is recessed in so there is nothing to tighten too. There was a scar on the back plate in one spot like it was rubbing. When I took it apart it was about 2-3 turn out with the locking washer on the nut so I don't think it loosened up from the last time it was apart. There would not be some shims that go behind? Thanks Norm

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy