TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Order Farmall Cub Parts Online

CUB HEAD BOLTS

Welcome Guest, Log in or Register

Author

mike

03-27-2004 18:38:33

Report to Moderator

anybody know the torque and length of the bolts and grade, IH here don't no much, if you can help me I really be happy thanksmike

[Log in to Reply] [No Email]

Rudi

03-28-2004 08:49:46

Report to Moderator

Re: CUB HEAD BOLTS in reply to mike, 03-27-2004 18:38:33

Mike:

As with all things Cub!, a lot of this info is available on the Cub Manual Server.

The pic of the order is below, but not the torque value which in the GSS-1411 is stated as

"Install the cylinder head cap screws. Using the sequence shown, tighten evenly in steps to 45 ft.lbs torque. Be sure to install all brackets and mounting clips under the cap screw heads before tightening."

This may be found under the Blue Ribbon Service Manuals, GSS-1411, Group 1, Page 01-14.

While you are there peruse the server.

Hope it helps.

Cub Manuals

[Log in to Reply] [No Email]

Farmer Bob

03-27-2004 20:53:24

Report to Moderator

Re: CUB HEAD BOLTS in reply to mike, 03-27-2004 18:38:33

Mike, When you get ready to tighten them down, here's the sequence.

[Log in to Reply] [No Email]

Bill V in Md

03-27-2004 19:22:35

Report to Moderator

Re: CUB HEAD BOLTS in reply to mike, 03-27-2004 18:38:33

There are 9 short (2 1/4") bolts and 6 long (3 1/4") bolts. Should be torqued to 45 ft lbs.....Bill V.

[Log in to Reply] [No Email]

John *.?-!.* cub owner

03-27-2004 19:12:11

Report to Moderator

Re: CUB HEAD BOLTS in reply to mike, 03-27-2004 18:38:33

Don't have any handy to measure length, but torque is 45 foot pounds (use antisieze), they are grade 8. You might be ahead to get them from your local dealer, or order them from www.cngco.com. the short ones (9 used) are $2.25 each (251230R1), and the long ones (6 used) are $1.50 each (251231R1)

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy