TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Ford 9N, 2N & 8N Discussion Forum

Just another example of Farmerizing

Welcome Guest, Log in or Register

Author

dan in co

12-06-2007 14:49:14

Report to Moderator

Last week I posted a message regarding a �Farmerized clutch rod. I got a lot of responses that talked about how the farmers would have to do quite a bit of improvising in order to get their tractors running and �git er done�. I thought I would keep up the theme.

The throttle control lever on my 2N was worn flat and the throttle quadrant was worn out as well, causing the throttle to slip back to idle. This picture shows how I cut a short piece of poly tubing lengthwise, slipped it over the rod and cable tied it in place. The lever has stopped slipping, but the tubing will likely need replacing frequently. Just another example of �Farmerizing� or maybe better said, �Agricultural Engineering�.

[Log in to Reply] [No Email]

Gregg E

12-07-2007 19:09:30

Report to Moderator

Re: Just another example of Farmerizing in reply to dan in co, 12-06-2007 14:49:14

Dan in Co, Im wondering why you farmerized it to that extent. I had the same problem on my 1943 2N and took a 4 in grinder with a thin cutting blade on it and groved the notches on the plate out a bit then I bent the trotle rod down about 1/4 inch and its working perfectly and looks really natural, meaning nothing hanging on it making it look farmerized.

[Log in to Reply] [No Email]

Sean (TX)

12-06-2007 17:41:56

Report to Moderator

For got the pic in reply to ZANE, 12-06-2007 14:49:14

[Log in to Reply] [No Email]

Sean (TX)

12-06-2007 17:41:26

Report to Moderator

Re: Just another example of Farmerizing in reply to Duner Wi, 12-06-2007 14:49:14

Here is another good one Joe T posted it awhile back...He drilled a small hole and JB welded a ball bearing in the hole... Seems like it would work good if you had any groves left at all in the quadrant...

[Log in to Reply] [No Email]

Dan in CO

12-06-2007 17:10:39

Report to Moderator

Re: Just another example of Farmerizing in reply to Dan, 12-06-2007 14:49:14

Nope, Not a Fergie. It is a 2N ser. # 9N280423 Born on date 2/23/47 Plate above the streeing wheel is a patent plate.

[Log in to Reply] [No Email]

ericlb

12-06-2007 16:56:30

Report to Moderator

Re: Just another example of Farmerizing in reply to dan in co, 12-06-2007 14:49:14

the tractor in this pic is a t series ferguson, see the serial tag above the steering shaft? dead give away, just like the to 30 i own if i ever get time to see just what i bought

[Log in to Reply] [No Email]

Dan in CO

12-06-2007 15:58:38

Report to Moderator

Re: Just another example of Farmerizing in reply to Ken(Ark), 12-06-2007 14:49:14

Yea, but that would be the right way & the beast wouldn't understand. Wait till I get "Beauty", I'll do it that way then if needed.

[Log in to Reply] [No Email]

Sean (TX)

12-06-2007 15:55:58

Report to Moderator

Re: Just another example of Farmerizing in reply to RustyAL, 12-06-2007 14:49:14

You can also do some welding and make the lever round again the cut new groves in the quadrant with a die grinder..

[Log in to Reply] [No Email]

GB in MT.

12-06-2007 15:53:32

Report to Moderator

Re: Just another example of Farmerizing in reply to Dunk, 12-06-2007 14:49:14

Dan; YOU GOT MAIL!!!!!

Gary

[Log in to Reply] [No Email]

Dunk

12-06-2007 15:48:40

Report to Moderator

Re: Just another example of Farmerizing in reply to Jimmyjack, 12-06-2007 14:49:14

GB in MT. said: (quoted from post at 20:43:36 12/06/07)

Dunk;

I just got to thinkin' about that, so I went to the book and checked.

You're right, NO such animule, on ANY "N" tractor!!!!!

Gary

Maybe a LongYanaKutieManiMarHoochieKyoti?

[Log in to Reply] [No Email]

GB in MT.

12-06-2007 15:43:36

Report to Moderator

Re: Just another example of Farmerizing in reply to Jimmyjack, 12-06-2007 14:49:14

Dunk;

I just got to thinkin' about that, so I went to the book and checked.

You're right, NO such animule, on ANY "N" tractor!!!!!

Gary

[Log in to Reply] [No Email]

GB in MT.

12-06-2007 15:34:47

Report to Moderator

Re: Just another example of Farmerizing in reply to ZANE, 12-06-2007 14:49:14

There is no set up like that on yours Dan. He must have an 8N.

2N's only have a throttle rod system, as far as I have ever seen.

Gary

[Log in to Reply] [No Email]

Dunk

12-06-2007 15:39:45

Report to Moderator

Re: Just another example of Farmerizing in reply to GB in MT., 12-06-2007 15:34:47

It's not on an N tractor as far as I know anything about, Gary, Dan...

[Log in to Reply] [No Email]

Ken(Ark)

12-06-2007 15:44:47

Report to Moderator

Re: Just another example of Farmerizing in reply to Dunk, 12-06-2007 15:39:45

There are no friction disks on a 9n or 8n , maybe the naa ? I dont have one of them ,,,,yet .

[Log in to Reply] [No Email]

John in Mich

12-06-2007 18:00:48

Report to Moderator

Re: Just another example of Farmerizing in reply to Ken(Ark), 12-06-2007 15:44:47

NAA, Hundred series and others use the friction disc as described. Both my NAAs have it.

[Log in to Reply] [No Email]

Dan in CO

12-06-2007 15:21:50

Report to Moderator

Re: Just another example of Farmerizing in reply to Ross Pugh(NC), 12-06-2007 14:49:14

MOUNTAINEER said: (quoted from post at 17:02:16 12/06/07) I had the same problem with one of my tractors--there is a friction disc set up under the batt box with some pressure fingers holding it down with a castellated nut-- also a spring is attached to the throttle control lever coming out of the friction assembly and hooked up to a spot back toward the dash--no doubt you are aware of this but it takes a bit of doing to replace the friction material with gasket stock-- worth the effort tho as it puts her back to original function even if the quadrant notches are worn-- looks like your fix works fine but thought you might like to try this one sometime

I was not aware of that. I will go out & look for it. is yours a 9,2, or 8?

[Log in to Reply] [No Email]

Ken(Ark)

12-06-2007 15:09:36

Report to Moderator

Re: Just another example of Farmerizing in reply to dan in co, 12-06-2007 14:49:14

�Agricultural Engineering�

I like your new term - A+

[Log in to Reply] [No Email]

MOUNTAINEER

12-06-2007 15:02:16

Report to Moderator

Re: Just another example of Farmerizing in reply to dan in co, 12-06-2007 14:49:14

I had the same problem with one of my tractors--there is a friction disc set up under the batt box with some pressure fingers holding it down with a castellated nut-- also a spring is attached to the throttle control lever coming out of the friction assembly and hooked up to a spot back toward the dash--no doubt you are aware of this but it takes a bit of doing to replace the friction material with gasket stock-- worth the effort tho as it puts her back to original function even if the quadrant notches are worn-- looks like your fix works fine but thought you might like to try this one sometime

[Log in to Reply] [No Email]

old 9

12-07-2007 16:43:22

Report to Moderator

Re: Just another example of Farmerizing in reply to MOUNTAINEER, 12-06-2007 15:02:16

The throttle friction disk is the same as the friction disk on lift quadrent lever. In Dennis Carpenter catalog part number is 9N-518 .. all of one dollar each in 2005 catalog.

Merry Christmas Joe

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy