Farmall & IHC Tractors Discussion Board |
Re: Re: Re: Sad day at the auction........
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Hugh MacKay on March 09, 2003 at 04:23:57 from (209.226.247.100):
In Reply to: Re: Re: Sad day at the auction........ posted by FM...Yo Hugh.. on March 08, 2003 at 18:21:35:
FM: In my neck of the woods it is hard for me to imagion an 806 with only 3,500 hours. Most tractors here see a min of 400 hours per year and a lot of the larger tractors are going the 1,000 hours per year. You sound like you are absolutely sure this tractor has only 3,500 hours. At 3,500 hours this tractor should feel like a new tractor to drive. Controlls such as steering, shift levers, throttle, hydraulics, pto and pedals should have that new feeling, no looseness, no side play. The 806 was one of the exceptionally good tractors. One in good working order should work alongside or out perform any new tractor in that hp class. It has dual live PTO, 3point hitch cat 2 or 3 lower link sencing. As a working tractor Farmalls became a lot more valuable with the introduction of 04 and 06 series configuration change moving operator foreward and allowing rear hitches to raise implements to a good height. Steering linkages improved greatly at that time also, you could put a 06 tractor on a small tractor job and have it manuver just as well. The items one must concern themself with on a low hour 06 or 56 tractor are items that deteriorate from lack of use. You have chosen a difficult one to acess. Get a guy with Farmall experience ( 2 minds better than one, I always find having a critic along when looking at anything used is valuable) and a dyno, go over it with a five tooth comb aproach. Value of this tractor could vary widely. If in super condition and you can put it to work with confidence it is worth a lot of money. Remember this; an end to end complete rebuild on an 806 today could exceed $20,000. Not likely but COULD.
Follow Ups:
Home
| Forums
Today's Featured Article -
Fabrication (Who Me? Make it myself?) - by Chris Pratt. First of all, what are the reasons for not fabricatin your own parts? Most judgements on what should be purchased rather than fabricated stem from: Originality - If the tractor restoration is to be 100% original, it is likely that you should spend the time and money to locate the component in the used or New-old-stock market. Since this can be extremely difficult, you may want to fabricate the item or purchase a modern replacement temporarily, but eventually, you s
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|