Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Tried plowing for the 1st time


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Okla/kans Bill on April 13, 2003 at 15:32:58 from (209.240.198.63):

In Reply to: Tried plowing for the 1st time posted by Kelly C on April 13, 2003 at 10:14:54:


Make sure your right rear wheel, on the inside, is the same as the inside of yor furrow wheel on the inside when both tractor and plow are in an straight line. To do this, lay a board along the inside of your right rear tractor wheel. It should line up with the inside of the plows furrow wheel. If not, adjust the V toungue hitch linkage until it does. Try not to adjust the drawbar. Ive forgot, since u got an H u can adjust the rear wheels in and out, so jack up the tractor and line the rear wheelup with the furrow wheel on the plow. In doing this, lay the board even with the furrow wheel and adjust the tractor wheel, not like what I said before, which is for non adjustable rear wheels on ole tyme tractors like mine. If your shares are good, adjust the leverslike so. on the first pass, raise the right lever (looking at it from the front) to 2/3 notches from the back. Keep the left lever about center. If it will not pull this, lower the right lever 2/3 notches, After getting the first furrow plowed, briong back the right lever to around center of the notches. Look back. If the diret is going over the back of the moldboard, instead of being thrown beside it, its too deep. Also, if the tractor has to be cluthced often, its too deep. If the plow skips up and rides above the groud, and if you can see 1/2 the moldboard a good part of the time, its too shallow. Do not over grease the trip mechanism, or it will think on its own, and trip when it wants. Hope this helps


Follow Ups:




Post A Followup

:
:

: Re: Re: Tried plowing for the 1st time

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership, ... [Read Article]

Latest Ad: Variable pulley for case 1530 skid loader [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy