Farmall & IHC Tractors Discussion Board |
Re: Re: Re: M Minimum Rear Wheel distance
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Hugh MacKay on July 09, 2003 at 07:33:48 from (209.226.106.186):
In Reply to: Re: Re: M Minimum Rear Wheel distance posted by Bill Perry on July 08, 2003 at 21:46:23:
Bill: My 300, 560 and 656 were all on 72" centers, which made them very close to flush with axles on outside, or 84". They all had 3" plus on each axle I could have moved them to make then about 78" to 80" on outside. Those tractors all had double bead rims, will depend on age of M whether you have the double bead rim. Shame to switch if you don't have to, I think you will like them much better dished out. I know my 300 with 13.6 tires could be made less than 78" outside with wheels dished out I had 16.9 on 560 and 656, probably closer to 80" with those. I may have seemed a bit harsh on my earlier post. I have owned about 5 trailers in my lifetime, and never was happy with any of them until I had deck over wheels. Trailers with deck between wheels and wide enough for big tractors tend to be just too wide for country roads. I've never had it happen but I have seen a few broken trailers along the road. I saw one that broke with a Farmall A on it. I stopped to help him, there was not a casting on the A that wasn't broken from the tumble. It was a car hauler,rated for 4,000 lbs. Trailers even the big highway trailers get cracks in steel, and that has to be monitered very closly. Many many times I have come home with scarey looking cracks on trailer frame, and not from excessive loads. Having owned a single axle highway tractor and 40' equipment trailer along with all the others, my opinion, nothing over gross weight of 15,000lbs. should be allowed on highway today with out air brakes. The others were fine 40 years ago when no one else was on the road. I just have a 5,000 lb rated car hauler today but I never haul anything larger than my SA, 130 or 140. Its just wide enough for those tractors set on 52" centers 60" outside. Just be careful, tractors with broken castings aren't much good, and flesh and bones even worse. Afterall an old guy like me has to keep you young fellows alive to chew the rag with about old iron. We need old knowledge, but even more important fresh ideas.
Follow Ups:
Home
| Forums
Today's Featured Article -
An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership,
... [Read Article]
Latest Ad:
Variable pulley for case 1530 skid loader
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|