Farmall & IHC Tractors Discussion Board |
Small Alternator for under the Hood installation
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by BIG JOHN on November 04, 2003 at 14:26:17 from (205.188.209.82):
I see the Mike J is asking about this so thought it might just be time to put this on the board again. I have been putting this small alternator on several tractors, replacing generators under the hood. It is a Hitachi #14231 which was used on 1978-79 Nissan 620 pickup with a 2 liter engine and a 1980 Nissan 720 pickup with a 2 liter engine. At NAPA it is part #2138130 - cost is right at $50 + core. The alternator is 4 1/2" in Dia. and 7" in length and will go right on the orginal mountings on the tractor. Use an 8" x 3/8" bolt and some pipe for spacers. Being Hitachi means that it is METRIC. You will need to drill out the mountings to 3/8". The tension adjusting bolt is also metric thread. The alternator is a three (3) wire set up which can be converted to one (1) wire. There are spade conections labled S & L and a BAT post conection. The L spade is for the idot light and can be disregarded. Use a jumper wire from the S spade to the BAT post and you are good to go. The pully is a split type that you can widen using a spacer (once again metric). You will need to use a disc type lock washer and some locktite because there won't be room to reuse the split lock washer that comes with it. There is a built in regulator and a resister to keep the battery from feeding back to the alternator. This is a sweet fit under the hood that I have used on H's, M's and W models, also Cubs and many others. Hope this is of some help. GOOD LUCK
Follow Ups:
Home
| Forums
Today's Featured Article -
Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|