Farmall & IHC Tractors Discussion Board |
Re: Re: Cotton Picker Years
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Harold H on December 09, 2003 at 13:31:06 from (67.30.243.34):
In Reply to: Re: Cotton Picker Years posted by JohnG(TX) on December 09, 2003 at 11:50:36:
John, If the two row is a picker rather than a stripper, it is a 214 low drum or 220 high drum from 57 or 58 or the A version of these from 59, 60, or 61. It should have a six cylinder either 220 or 240 engine. I don't know about your date code but the two row wasn't introduced untill 1957 so it can't be 1945. I don't know stripper models, if it is a stripper rather than a picker, as we never had strippers in the Mississippi Delta, only pickers. The M-14 was a low drum version of the M-12 high drum picker. It probably was introduced about 1950 or 51 and was replaced by the 114 low drum one row picker in about 54. When mounted on an H or M or later variations of these chassis, (SH, SM, 300, 400, 350, 450, 460, 560, etc) the drive gear box mounted where the belt pulley mounted. I'm not sure of the type drive on the later one row models mounted on tractor models not derived from the H/M as we never sold one and I have never actually seen a late model one row picker up close. The early low drums could also be mounted on a C or Super C, which used a different drive, but they were very underpowered and few were sold. I don't know of a source for cotton picker serial numbers. The one row models are M-10 high drum, M-12 high drum, M-14 low drum, 114 low drum, 120 high drum, 114A low drum, 120A high drum, 314 low drum, 320 high drum, 500 low drum, and 502 high drum. There may be a couple more I left out, but as I stated, in new pickers, we sold only two row pickers after the 214/220 came out in 1957. When we were selling new one rows, 95 % of them in the Mississippi Delta were high drums (M-10, M-12, and 120). If you look in the header and count spindles, if there are 14 spindles on each bar it is a low drum. If there are 20 spindles on each bar it is a high drum. Hope this information helps. Harold H
Follow Ups:
Home
| Forums
Today's Featured Article -
The Cletrac General GG and the BF Avery A - A Bit of History - by Mike Ballash. This article is a summary of what I have gathered up from various sources on the Gletrac General GG and the B. F. Avery model A tractors. I am quite sure that most of it is accurate. The General GG was made by the Cleveland Tractor Company (Cletrac) of Cleveland, Ohio. Originally the company was called the Cleveland Motor Plow Company which began in 1912, then the Cleveland Tractor Company (1917) and finally Cletrac.
... [Read Article]
Latest Ad:
1997 cub cadet 7275 compact utility tractor 4wd hydro trans cracked block 3500
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|