Farmall & IHC Tractors Discussion Board |
Re: Re: Baler on a 350U Wheatland
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Sean in Calgary on April 06, 2004 at 09:50:08 from (66.244.207.150):
In Reply to: Re: Baler on a 350U Wheatland posted by Hugh MacKay on April 05, 2004 at 18:13:11:
Hugh, It has been so long since I have been on this board that I cannot remember the definition of live PTO. If my recollection serves me right, I do. As long as I have the PTO engaged, it spins, irrespective of whether the tractor is in gear or not or whether or not the transmission clutch is in or out. Once I pull that PTO level, it spins the PTO sharft, no matter what I do to the tractor (other than turn it off - grin). I am VERY happy to hear that I should be fine, HP-wise. Right now I am just leasing out my land to a cattle farmer who cuts and bales (big round bales) the crops and gives me a reasonable amount of $$ for the bales. I have had a few offers from horse ranchers in the area who would be willing to pay quite nicely for small square bales. I only have 18 acres so I am not talking about such a large task that I will have to quit my day job to get it cut, raked and baled. The big investment was getting a New Holland swather with conditioner at an auction and then getting it back in running order. Apparently these old cast iron engines do not like sitting with the fuel system half filled with water. That cleaning job took some time. Now, I just have to hope that everyone else in the area doesn't also want that baler. There was a reasonably good condition square baler at an auction I went to last June and the darn thing sold for $7,000.00 The farmer who sold it was over at my place last week and he is still laughing. TAn identical baler was for sale at the JD dealer (also used) for less money. Thanks again for everyone's help. Sean
Follow Ups:
Home
| Forums
Today's Featured Article -
Tractor Profile: Earthmaster - by Staff. This tractor, manufactured by the Earthmaster Farm Equipment company in Burbank, California was made for only two years. The Model C came out in 1948 and was followed by the "CN" (narrow-width model), "CNH (narrow-width high-crop model), "CH" (high-crop), "D" and the "DH" (high-crop) in 1949. The main difference between the models was tire size, tractor width and cultivating height. The "D" series were about 20 inches wider overall than the
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|