Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Well, Phooey


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Allan in NE on July 06, 2005 at 05:27:47 from (148.78.243.24):

In Reply to: Re: Well, Phooey posted by P Backus on July 05, 2005 at 21:16:20:

Hi Paul,

Yep, the whole gizmo is mounted on, it rotates around and is pulled by that big pipe running down the backbone.

The hitch and the plow frame are actually two entirely different units with the cylinder connecting the two in a lateral manner.

third party image

The laticework of boltholes in the guagewheel plates is where the "landside depth" of the plow is set by the placement of the stopbolt arm.

Hard to see in the picture, but there is a stoparm at the top and at the bottom of the plates and the gaugewheel arm moves between the two, depending on direction of travel.

third party image

The 3-point hitch on the tractor is then set to the "float" position by the collars being dropped to their lower position.

This, in effect, puts the "plowside" depth (and the only weight the tractor carries) on only one arm of the 3-point hitch and both the sideways and the fore/aft level of the plow is set by the one arm of the tractor's hitch doing a "balancing act" to the depth of that gauge wheel.

When the plow spins, gravity forces the latch at the gaugewheel to unhook, the wheel drops to the other direction and the latch then hooks again on the other short stopbolt arm.

In short, the whole plow is controlled by that gaugewheel. If a cornstalk or something should happen to keep the gaugewheel from changing directions, all bets are off because the plow will head for China and stop you dead in your tracks. :>)

Allan

third party image


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Harvestin Corn in Southern Wisconsin: The Early Years - by Pat Browning. In this area of Wisconsin, most crops are raised to support livestock production or dairy herds in various forms. Corn products were harvested for grain, and for ensilage (we always just called it 'silage'). Silo Filling Time On dairy farms back in the 30's and into the first half of the 40's, making of corn silage was done with horses pulling a corn binder producing tied bundles of fresh, sweet-smelling corn plants, nice green leaves with ear; the ... [Read Article]

Latest Ad: 2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy