Farmall & IHC Tractors Discussion Board |
Re: Man o Man You shouldv'e seen the A Plow Snow!
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Hugh MacKay on December 13, 2005 at 12:47:33 from (209.226.106.107):
In Reply to: Man o Man You shouldv'e seen the A Plow Snow! posted by Farmallkid From Ont, on December 12, 2005 at 14:21:52:
Mitch: So you just found out another one of life's little secrets. Pound for pound that little offset is the best tractor IH ever built. Doesn't matter whether it be A, SA, 100, 130 or 140, given their own weight they make their big brothers look very ordinary. I'll throw you another idea for next summer. Find a sheet of 1/2" steel 4' x 10'. Turn about 5" up 45 degrees at each end. Weld heavy angle iron along each side on the up side. Hook a heavy 4' chain to each end. Now your in business for a real farm situation tractor pull. None of this whimpy stuff of starting with a load that gets heavier as you go. In a real farm situation you start with a full load and go. No classes in this pull, Farmall A competes against the mighty M. The winner is the tractor starting away with and pulling 10' the highest percentage of its own weight. Pullers can add weight to their tractors as they see fit. Adding weight gives no real advantage. Often time it hinders. It doesn't matter whether these are regular letter series or supers, the A will be the tractor to beat. It will cause the others a lot of grief. Operator skill is very important. I've seen 3 guys pull the same tractor and not place in sequence. I've also seen the same guy win with any of these tractors. If I were to enter one of these pulls, my pick would be A or SA. It has the best chance of pulling over 3 times it's own weight. I've seen a lot of these type pulls and from what I've seen would rank A - 1st, H - 2nd, M - 3rd and C - 4th.
Replies:
Home
| Forums
Today's Featured Article -
Fabrication (Who Me? Make it myself?) - by Chris Pratt. First of all, what are the reasons for not fabricatin your own parts? Most judgements on what should be purchased rather than fabricated stem from: Originality - If the tractor restoration is to be 100% original, it is likely that you should spend the time and money to locate the component in the used or New-old-stock market. Since this can be extremely difficult, you may want to fabricate the item or purchase a modern replacement temporarily, but eventually, you s
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|