Farmall & IHC Tractors Discussion Board |
Re: Questions about 560
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Wardner on July 11, 2006 at 12:45:31 from (207.69.137.36):
In Reply to: Re: Questions about 560 posted by RustyFarmall on July 11, 2006 at 10:21:18:
I don't agree with some of your points. Engineers always strive to do more with less while trying to preserve an acceptable longevity. Turbos always make more power with less weight and sometimes with less cost. They came into their own with aircraft. Less weight applies here. Airplanes also benefitted due to the fact they operate at reduced atmospheric pressures snd oxegen content. Before Detroit Diesel came out with their V-designs, they turboed the 6-71. After they came out with the V designs they turboed some of the new designs. The turbos doubled their product line overnight. It has never been about efficiency. Pounds of fuel per horsepower hour didn't change that much. Sure the turboes extract power from the exhaust but they also add loads in pumping losses. You may point to reduced exhaust noise as evidence of power scavenging, but in reality, the reduction is caused by averageing the wave pulses through the turbine. They are self muffling and produce back pressure in the manifold. Turbo technolgy and application is very complex. Sometimes it cannot even be engineered. The applications have to be fitted and tested using different a/r ratios. A random turbo off the shelf or another application may benefit the engine, but it is a longshot. When all is said and done, most turbos are tuned for a narrow load, RPM, and horsepower range. This is why we see wastegates on many of them. It extends their power band by sacrificing max power. Max power is a valid engineering consideration for farm tractors and over-the-road trucks as the loads are constanly changing. It may feel good to do a little shade-tree engineering, but I doubt if any of us has the experience, equipment, money, or smarts to do a good job on turbo selection.
Replies:
Home
| Forums
Today's Featured Article -
Women and Tractors - Tractor Engine Repair - by Teri Burkholder. One of the great things about working on a tractor engine with your other half is that you know what he is thinking of at all times and can anticipate his every move and his next thought of what he will do. With Ben, anyway, I can tell! He'll be busy working and I’m handing him tools and he says, "give me that..." and I’ve already got it in his hand or "hand me that....."and I’ve got the portable light right where he needed it placed to see. "Run in the house and get me a...."as I open th
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|