Farmall & IHC Tractors Discussion Board |
Re: Fast Hitch Plow
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by the tractor vet on August 22, 2006 at 09:49:50 from (75.24.29.127):
In Reply to: Fast Hitch Plow posted by BOBM25 on August 22, 2006 at 09:27:57:
Well if you are not use to setting up a plow on fast hitch and don't have the book , here is some easy steps to fallow , First off how deep do you want to plow if it is a 14 inch plow 7-10 inches as they say depth is half the width if 16 inch bottom 8-12 ya i know someone will dispute this but we have pushed the 16 inch plow to a foot Get yourself two blocks that massure around 8 inche high put the left rear and the ft end up on the blocks while setting on a flat level ground , shop floor or drive with the plow hooked up to the tractor set the plow down and see how it lays down on the ground then make your adjustments to the leveling crank or move the bolts on the plow hitch . Next what kind of bottoms are on your plow PlowCheif or Super Cheif . The plow cheif is a three pice bottom that has a removableor replaceable plow point then the shear then the shin this is a vary expencive bottom to maintain. The super cheif is a two pice bottom with a long shear and a shin . Now the Super Cheif bottom you can get several differant shears for them to hepl penatrate hard rocky ground. Also you can change the pitch of the bottom on a I H plow to be more agressive if you look at the land side of the plow and you will see on the stem that the piviot bolt has a rectangel head and if the head is not wore to bad you will see and arrow pointing either up or down all bottoms should be the same if the arrow is pointing up then this is the normal posision and if ya want them to go in faster and dig deeper for harder dirt then loosen the bolts up that hold the bottom to the stem and turn the bolt with the arrow to point down. . Also always start off with new iron on the bottoms and pay close attenshion to ware of the shears shins and land sides. If ya let the shears ware down tofar then you start to ware the FROG out.
Replies:
Home
| Forums
Today's Featured Article -
Pitfalls of Tractor Engine Rebuilds - by Chris Pratt. The first pop after you have put the machine together with your own hands is exciting and pleasing. The whole experience can be marred if one moves too fast and makes too many assumptions that they can just use "as is" some parts they should be closely scrutinizing and possibly attended to. In such cases, rework makes what could have been a fun project turn into an irritant or even a nightmare. Minor Irritants To give you an example of an minor but irritating proble
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|