Farmall & IHC Tractors Discussion Board |
Re: Live PTO kit for H
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Delta Dirt on October 07, 2006 at 16:09:46 from (64.49.3.194):
In Reply to: Live PTO kit for H posted by Nathan S. Clemons on October 06, 2006 at 10:16:51:
I have had a lot of experience with roto tillers---back in the 60"s & early 70"s, I worked for Howard Rotavator as a factory rep. Have used them on the farm and still occasionally use one. For most applications---the H, M & 460---560 (5 speed transmission) tractors had to fast of forward speeds to really do an adequate job. One thing for certain----you need a direct drive gear train that will provide a "braking force" against forward thrust from the tiller. The early TA"s would increase pulling power, but allow "free wheeling" against the forward thrust of the tiller (as if disengaging the clutch). Depending on how serious your tiller plans are--I would highly recommend finding a tractor with a little more HP, 8 speed transmission (with several low forward speeds), live PTO and live hydraulics. Its not that it can"t be done with the H---just that you would probably be better satisfied in the end. I have run an 80" cut Rotavator on one of my M"s---but never was real pleased. Also have run an 80" on my Kubota L2850 (28 hp), but with extremely low speeds and operating the Rotavator very shallow. One thing to keep in mind----don"t know about other brands, but most of the Howard machines have a multi speed gear box, where you can change the blade speed in the rear of the gearbox. The slower you turn the blades---the less power is required from the tractor. At the same time---in order to take a smaller bite with the tiller blade (and result in a finer textured seed bed), if the blades are turning slower---you need a slower forward speed on the tractor. Conversely----with more power, you can speed the blades up, move the tractor faster and do more work. A good rule of thumb is 1 HP for each 1" of cutting width of the tiller. For lesser HP ratios---you really need slower forward speeds. Good luck on your project----keep us posted. Delta Dirt Avon, Ms 38723
Replies:
Home
| Forums
Today's Featured Article -
A Lifetime of David Brown - by Samuel Kennedy. I was born in 1950 and reared on my family’s 100 acre farm. It was a fairly typical Northern Ireland farm where the main enterprise was dairying but some pigs, poultry and sheep were also kept. Potatoes were grown for sale and oats were grown to be used for cattle and horse feeding. Up to about 1958 the dairy cows were fed hay with some turnips and after that grass silage was the main winter feed. That same year was the last in which flax was grown on the farm. Flax provided the fibre which w
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|