Farmall & IHC Tractors Discussion Board |
Re: is this right?
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by John T (Yo Bob M ?) on January 08, 2007 at 06:49:58 from (66.244.90.5):
In Reply to: is this right? posted by Pat-CT on January 08, 2007 at 06:23:18:
Pat,,,,,, The battery is charged as its ungrounded - post is on the big starter switch post via that big honkin battery cable,,,,,,,,,then theres a wire leading to the Supply side of the Ammeter,,,,,,,,,then current goes through the ammmeter which is almost like a dead short circuit over to its other Load terminal,,,,,,,,then down to the BAT terminal on the Cutout Relay,,,,,,,,,,then through the cutout relay whose contacts close once the genny is working,,,,,,,,to the Armature post on the genny Yayyyyyyyyyy The battery is connected there at the big starter switch post which serves as the connection point for other (then the starter)wiring to the battery. If you follow the diagram you can see the curent path whereby the gennys output (its ARM post) gets to n charges the batetry once the cutout relay contacts close. Yo Bob M, I have a question on that wiring diagram. If the wire from the gennys Field post goes FIRST through that Field resistor up on the LHBD switch (i.e. the resistive Low Charge condition) how does the gennys field ever become dead non resistive grounded for the High Charge condition????????? Looks to me like the switch would have to have a connection terminal to the gennys field such that it can get a ground path EITHER straight to ground (high charge) or via that resistor (low charge). The way the diagram looks it can ONLY be in the resistive Low Charge cuz how can it ever short by pass around that series in line field resistance as the diagram shows???????? Im sure you know this stuff (especially IHC) better then me so I take the diagram as a typo or pictorial error or else I dont understand this at alllllll lol talk to me God Bless yall John T
Replies:
Home
| Forums
Today's Featured Article -
Women and Tractors - Tractor Engine Repair - by Teri Burkholder. One of the great things about working on a tractor engine with your other half is that you know what he is thinking of at all times and can anticipate his every move and his next thought of what he will do. With Ben, anyway, I can tell! He'll be busy working and I’m handing him tools and he says, "give me that..." and I’ve already got it in his hand or "hand me that....."and I’ve got the portable light right where he needed it placed to see. "Run in the house and get me a...."as I open th
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|