Farmall & IHC Tractors Discussion Board |
Re: Tractor Bushhogs
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Jim on November 10, 2000 at 14:35:37 from (209.100.42.90):
In Reply to: Tractor Bushhogs posted by Geoff on November 10, 2000 at 10:54:57:
Have a similar situation, 40 acres, rolling hills, majority either pasture or ex-crop land. lots of cockel burrs. Example of elevation change, from north end of property to rear is change in 100ft down, over sight line of a little over 1500 feet, with last 500 having a 40 ft drop to a creek and small pasture area. In the more level areas I use my H with an old 8 ft rotary cutter, pull type. Even in tall stuff, areas not cut since last October I had no problem cutting this past October. But do wish I had duals on the rear and wide front, sometimes running at a slight angle and then hitting an unseen ant hill, or terrance, can cause the old "old poop" how far can this baby go feeling arise. Depends on your budget, and what else you want to use the tractor for. Mine, whole set up for around 2000. But now I want to add 3pt, duals, and maybe wide front, (realize I will lose some turning ability). Lower set utility, with 3pt, and 5 to 7 foot mower would probably be the way to go if your looking to keep everything cut, lots of steep hills that you have to run along side of, or dont have enough room to run all the the way down, turn around and come back up on. And also depends if you compare what your buying, what I spent on the H equals a small cheap lawn tractor at HomeDepot or WallMart, spending 4000 to 5000 on a utility puts you into the John Deere lawn tractors. (Guy at work spent 7000 on his for a one acre suburban lot to mow and push snow around.) Anyway just my thoughts, but whatever you do, please be carefull of the hillsides and if it dont feel right, dont do it. Can always buy a few sheep cheaper than a hospital bill or a new tractor. Jim
Follow Ups:
Home
| Forums
Today's Featured Article -
An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership,
... [Read Article]
Latest Ad:
Variable pulley for case 1530 skid loader
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|