One medium to large deer One pickup load of firewood Chain saw Shovel Large hunting knife Skinning knife One sledge hammer One 1½” black water pipe 10 to 12 feet long Baling wire One heavy plastic tarp Several assistants One or more cases of beer Assorted spices
Shoot and field dress one medium to large deer. Hang up in a suitable tree to cool.
While the deer is cooling, make the following preparations:
Locate 2 small tree trunks, approximately 3” in diameter, each with a fork in the trunk. Trim with chain saw so that the result is two 5 foot long uprights each with a “Y” at the top and a point at the bottom.
Dig shallow hole, approximately 3 feet by 8 feet by 1 foot deep. With the dirt excavated from the hole, form a berm around the outer edge of the hole. It is desirable that this hole be adjacent to, or in the near vicinity of, a sturdy picnic table.
Using the sledge hammer, drive one of the uprights into the ground on each end of the hole, with the “Y” in the top aligned with the opposite end of the hole. Care must be taken not to split the “Y”. This is best accomplished by laying a piece of firewood in the “Y” and striking the wood with the hammer. It is desirable to hold the piece of firewood by the end, so as not to strike one’s hand instead of the firewood. Drive the uprights approximately 1 to 1½ feet into the ground.
Fill the hole with firewood and ignite. It is important to use well cured hardwood such as oak or elm.
While the fire is burning down to hot coals, skin the deer. While doing so, sever the head at the neck, and all four legs at the center joint. Discard. Coyotes will finish disposing of the head and legs within a few days. Add more firewood as needed.
Lay the tarp on the picnic table. Lay the deer on the tarp. Position the pipe through the body of the deer. A suitable hole may have to be cut in the neck area to allow the pipe to pass through. The body of the deer may need to be attached to the pipe. Baling wire works well for this. With an assistant lifting the other end of the pipe, lay the pipe in the “Y”s at the top of the uprights, with the deer suspended over the fire. Replenish the wood on the fire as needed. Attach a pair of vise grip pliers to one end of the pipe to provide a handle to rotate the pipe, and thus rotate the deer over the fire. While the deer is cooking, rotate the pipe a quarter of a turn every fifteen minutes.
Care must be taken not to cook the deer too fast. Ideally, cooking time will be about 4 hours. As this is hot work, the attendants must avoid dehydration by consuming an appropriate quantity of suitable liquid throughout the entire procedure.
When the deer is done, lay the deer on the tarp on the picnic table. Carve into suitable portions and distribute to attendees.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.