Posted by JDseller on November 29, 2011 at 06:22:34 from (208.126.196.144):
In Reply to: Re: Ethanol posted by Dick L on November 29, 2011 at 02:58:01:
Dick L that wonderful wet mesh is 65% moisture content, 7% protein, heavy on the sulfur. You have to really watch feeding too much or you get "brainer cattle" that walk in a circle back wards and then 80% die.
Lets look at it on a dry matter basis:
Wet corn gluten mesh 2000 lbs x 35% dry matter(65% moisture)= 700 lbs of dry matter 700 lbs x 7%= 49 lbs of true protein per ton
Dry Corn 2000 lbs (35.71 bu.) x 85% dry matter(15% moisture)=1700 lbs of dry matter 1700 lbs x 8.5%= 144.5 lbs of protein.
So it takes three ton of the Wet feed to equal one ton of corn. IF you do it on an energy basis it is even worse. It takes 4.2 ton of wet feed to equal one ton of corn.
Right now since cash corn is under $6 the economics don't work right at the moment but guys will not change their rations for a while.
A ton of corn is 35.71 bu. x 6= $210.69
A ton of wet gluten is $85.00
So it would cost $250.66 to equal a ton of corn in feed matter.
When the wet gluten was under $20 per ton it was cheaper but it had risen in cost here due to Cargil buying it up to mix into a sweet bran they are shipping south to Texas in coal cars. It caused a real shortage this last month around here. This really hit the guys hard that counted on it to feed. Many of them had not put any silage up so they where scrambling to find other feed stuffs. It also had followed corn prices up last year too.
I have feed it before but my cattle are sold on a grade and yield system. When they where finished on the wet gluten feed they had a lower premium when slaughtered. I stopped feeding it four years ago.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
