technicaly no,in practice yes.LOL you would be amazed at the cobbled up messes ive seen folks plowing with over the years, and doing a good job of it!.plowing quite honestly,once you get your plow set right,is one of the simplest things you can do.My advice,would be to look for a three bottom economy type plow,modern enough you can buy parts for. I say a three bottom because quite honestly,around here anyway you can buy one in pretty good shape for a fourth the price of a two bottom.The reason is food plots.All three bottom and four bottom type equipment is selling for scrap prices here,simply because its too big for the food plot/wannabes and its too small for the real farmers who need to run as economically as possible.If your grounds too hard to plow six or seven inches deep,plow it four,wait a month and plow it again.once youve got it broke out its not near as hard to keep it broken.The reason why there is not as many disc plows in your area is simply there wasnt so many made to start with.It wasnt at all unusual for a dealer selling a new tractor to throw in the plow with it,especialy on a tractor that at the time had a oddball hitch. And a moldboard plow is simply more versitile in lots of conditions and farmers were used to using them and understood them.BUT consider this,the disc plow,or disc tiller was made expressly for turning a lot of ground,and doing the minimum amount of tillage,it breaks up the ground more letting you very often skip the first discing folks did ,and many times the second also.My grandad had exactly one tillage implement on his farm for as long as i remember,that was a five bottom disc plow,all his tillage was done with one pass,he simply drug a harrow behind it and drilled .thats it.nothing more at all.your sandy loam is well suited for this and in fact is just exactly what a disc plow/tiller was made for.when you think about it realistically,lets figure it.Everyone says gas is going to $5 a gallon,dust laws are being pushed through,add in the fact that were in the largest drought since the dust bowl with no signs of relief,and a disc plows ability to turn the ground and leave a lot of cover on the surface to help conserve moisture,I certainly wouldnt rule one out by any means .I guarantee you thats what i'm using .If i want more seat time i'll make a road trip.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.