Posted by Name With Held on October 16, 2012 at 11:09:54 from (24.229.80.165):
I have a friend that farms a few miles from me. I knew him in high school but hadn’t seen him in 12 years. Just ran into him last year for the first time, and found out he is milking cows just a few miles from me. He rents a barn, and only has a few acres rented. Buys most all his feed, which has been rough the last couple years. I had picked up 8 additional hay acres near my place and offered to let him farm it on halves with me. I fronted all the money, and ended up doing most all the work,and suppling most all of the equipment and fuel. I did the mowing, tedding , and baling, while he raked. We split the hay 50/50. I also sold him a fair amount of my hay at a fairly discounted rate. On the 10 acres he farms on his own I have let him use my discbine for free. I didn’t mind helping him out, and 10 acres cut 4 times a year isn’t going to wear out my machine. My friend has recently decided to move out of state where he can afford to buy his own place. He has almost no equipment, and he would love to have a discbine like mine. I buy and sell a fair amount of equipment on the side, to supplement my farm and day job income. I recently stumbled across a discbine like mine on craigslist for a very reasonable price. It is about 600 miles from my place. I could really use the profit from selling this discbine to help buy a newer baler. I guess my question is should I sell it to my friend at my cost? I don’t even know if he can afford that….On one hand I feel like I should help him, on the other hand I have helped him many times over this year and I kind of feel like he should start helping himself. If he had cancer, or broke his leg, it would be one thing. But if he just doesn’t have enough get up and go to get things done, be organized and make a living, that’s his problem. Opinions and advice welcome.. .
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.