Posted by Adirondack case guy on November 11, 2012 at 15:01:26 from (74.69.160.79):
In Reply to: Shed Heat posted by Greg K on November 11, 2012 at 06:06:27:
Greg, You can't beat radiant floor heat. when you back trucks in after a call the snow, water and crap drips off them and dries up on the floor. The trucks asorb the heat coming up from the floor and are always warm, Also If you have a high ceiling the heat does not go to the ceiling as long as you don't move it with ceiling fans. The downfall to Radiant floor heat is POOR construction methods, and improper insulation materials. (1) the sub grade HAS TO BE PROPERLY COMPACTED. (2)It HAS TO BE DEAD ON SMOOTH, no humps or dives if 2" construction grade insulation is used, (it will bridge) BUT I DO NOT recomend styrofoam under floors where "heavy point loads" are involved. (A fully loaded tanker, or town plow truck fully loaded and setting on 2-3 axles, will exert some massive weight to a very small area of floor. You need at least 6" of concrete reinforced with #4 rebar criscrossed 16'" OC and 3/16' mesh set on "chairs" holding the bar and mesh with attached 7/8" radiant tubing in the middle of the crete, not under it. I recomend insulating blankets with vapor barier under these floors, as it is not as prone to colapse under heavy loads. Be sure to insulate the building perimiter to a minimum depth of 2'vertically, and also horizontally just under the external ground surface and be sure to place a thermo barrier up to floor surface grade at all doors. Where you have big overhead doors place radiant tubing much closer in front of them. Also BE SURE you dig a haunch under, and add extra reinforcement under and around floor drains in floor as this area is always weak, due to the open area. If and when you want to supplement your heating unit with Solar,/ storage tanks, and posibly a wood gasser boiler you can very easily do it, if you initially plumb in supply and return ports caped off. This is no BS, I was a comercial builder and have worked with and certified as an installer for companies such as Radientec, Sun Max Solar, and ProFab Wood boilers, Baxi, and others. Loren, the Acg
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
