Dan, automotive engines are electronically governed to a variable speed variable load, while generators are governed to a constant speed. I"m told that the ecm from your car can be reprogramed for constant speed, but I have more than a little reservations about whether that is true. If I may be blunt, while I have not used and automotive engine to power a generator, I have used automotive engines to repower marine inboards. It is my experience that rebuilding a pre 1970 engine works far better than trying to use a post 1980 engine. The straight 6 GM 250 works well as well as that V6 Buick engine that was used in Jeeps in the early 1960"s. I think it was a 3.6 or 3.8, but it"s been a long time. What makes that V6 work good is that you can buy commercially sold accesories, such as marine exhaust manifolds. I imagine that you could buy a commercially available electronic governor for an older engine. The issue is speed droop. Even if you set the throttle at the correct speed, lets say 900 rpm (the speed for the last diesel generator I worked on in the Navy), everytime a load changed, such as the refrigerator started, it would cause the engine speed to drop. You would need to be able to add fuel and cut back on fuel as needed to maintain that speed across a varying load range. To be honest, even with a perfect governing system, carborators are only so sensitive to control, anyway. Your next issue is coupling the generator to the engine. Unless you can run a dial indicator well, I recommend using belts and pulleys. They are far more forgiven regarding alignment. Remember that your pulley diameters will affect your generator speed, hence your frequency. If you can mount your fuel tank above the engine with the line coming from the bottom of the tank, like on a tractor, you will have enough pressure to power a GM 250 straight 6 with a carburator. I used one to power a buzz saw years gone by. I used the fuel tank from an Allis Chalmers WD, but if you can get one of those old Farmall fuel tanks that is a straight egg shape the length of the hood, I would think that would work even better. I would install a filter and a coalescer with removeable elements etc. I think we both know that depending on the load you put on your generator, or whatever you do with your engine, your heat load is likely going to change, and possibly a lot. I was asked by a few members of the Aux to repower a couple boats. It was not that difficult to simply use the raw water to cool the jacket water, especially since the pump and expansion tanks were already on board. If you are using the engine in a generator set, I would expect to use a much larger radiator. The electric fan motor may also be a problem (another reason why older engines work better). Another thing that I often would do when taking an automotive engine and using it as either a stationary power plant or marine application is the oil pan. I often cut the bottom of the oil pan just above the bevel, and weld an inch and a half to it. I then weld the bottom back on. I had an indian friend that would make me a slightly longer pick up tube, as well. This increases the amount of oil in you crankcase. I would also upgrade the lube oil pump to a high proformance. If you were using that old Buick engine, the kit comes with gear lobes that are about a half inch longer. Since the oil pump for that engine is assessable from the outside of the engine, it is an easy change. Your engine not so much. Your engine also doesn"t have a flywheel. It came with an automatic transmission and a flexplate, which is to light for most other applications. Just because I"ve never seen a Century with a manual transmission, doesn"t mean that there never was any. Let"s imagine you can find a flywheel, and it"s heavy enough for what you want. Your engine was a front wheel drive block, so you will need to fabricate the housing for the flywheel. Basically an engine from the 1980"s is a terrible stationary power plant engine. I seriously recommend using an engine from the late 1950"s thru 1970 for any stationary power plant. Pay close attention to what controls your engine speed, cools your engine and lubricates your engine. Often after reusing an engine, I find that antifreeze is replaced with simple anti corrosion coolant. Your change in use may warrant a change in the heat setting of your spark plugs also, but that is something you can experiment with as you use it.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.