The answer depends whether its a "seperately derived system" or not.
SIDE NOTE BEFORE WE PROCEED just in case one wonders: If a genny is used to power plug and cord connected equipment from on board mounted receptacles, the gennys Neutral to case/frame bond should remain intact and theres no requirement for an external Grounding Electrode connection BUT if local authority says otherwise then do what they say NOT anyone here lol
AND MORE IMPORTANT THE ANSWER DEPENDS UPON WHAT THE LOCAL AUTHORITY SAYS NOTTTTTTTTTT MYSELF OR ANYONE HERE (professional or lay persons) SO BEST CONSULT WITH THEM OVER ANY OF US
(In the comments below Im talking about a typical residential home service of 120/240 volt single phase three wire)
1) If you want to use ONLY a 2 pole transfer switch, i.e. YOU DO NOT SWITCH THE NEUTRAL only the two hots, the gennys Neutral to case/frame bond is severed,,,,,,,,The Gennys Neutral and Utility Neutrals are bonded together,,,,,,,,The safety equipment GroundING conductor is carried out and bonded to the gennys now floating (NOT bonded to Neutral remember) case/frame.
2) If you use a 3 pole transfer switch, i.e. the Neutral plus the 2 hots are switched, the gennys Neutral to case/frame bond remains in place and the Neutral/Case/Frame is all tied to a Grounding Electrode Conductor (like bare No 4 copper wire) which leads to a proper approved Grounding Electrode such as driven rod or rods or water pipes etc etc
My best free and worth the same (NOTHING) advice would be to consult with your local Utility Provider and any local governing authority AND AGAIN DO AS THEY SAY OVER ANYTHING ANYONE HERE, LAY OR PROFESSIONAL, MIGHT THINK. Ive been retired as an EE tooooooo longgggggggg and am rusty as an old nail on the latest NEC so NO WARRANTY on my opinions either, but its still my best faith and best remembered way to correctly earth ground a household generator, PLEASE see what the other professional electricians and engineers and technicians have to say also. For the 1,000 time (I so enjoy posting this every time lol) beware of taking advice from Billy Bob and his know it all brother in law Bubba who wired their own homes over a case of beer and everything works so they must be experts lol
Keep safe, consult with your Utility Provider and Local Authority, it may save their and/or you and your familys lives.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.