I looked through several pages attempting to determine the requirements for Army snipers with no joy. I'm sure they are good, but the 1.43" @1K yards appears to be THE record and it's not held by a military shooter as far as I can find. 1.43" is a lot different than the 9" kill zone on a human target. I've shot at 1K yards at the standard target for that range which I believe is about 10 feet square. Let's just say no one is in certain danger from me at that range, mostly due to wind drift as my dispersion was mostly lateral. At any rate, I'll leave the bragging to others.
JF- You don't need to "lock the rifle down to a bench". You simply need a solid support for the rifle and you. As far as your rifle, if I understand you made a lead filled barrel sleeve to fit over a production barrel, put it in a non-bedded stock held by a single screw and are using the standard grooved receiver rings and a Walmart scope with bulk 22 ammo? I mean absolutely no offense, but 3" at 50 or 75 yards might be all you'll get. To start with you have an inexpensive action and barrel of no special quality and, IIRC, a sliding fit action/barrel junction which is pinned. Then you put a heavy tube over it, filled it with melted lead, and depended on the single action screw alone to hold it steady in the unbedded stock. Then you put an inexpensive scope in the groove type mounts and wonder why you aren't getting tight groups. There's a very good possibility that your set up is moving within the stock at every shot to start with and that the barrel is in torsion just sitting there. In short, I like your stock, but you might want to rethink the rest of it.
I have a Winchester 52 similar to GVSII, mines a 5 digit ser# IIRC, wearing a 6x Lyman Junior Target spot. At 50 yards with select ammo I expect 10 shots in a ragged cluster under an inch. At 100....on a still day with no mirage, maybe it would shade an inch, but something in the 1.5" area might be more like it. With standard bulk 22 I'd be happy with 2.5" and if the breeze is up closer to 3-3.5 and I wouldn't be surprised if the groups were a little bigger. Both my Remington 511s would be doing good to stay in the 1.25-1.5" at 50-60 yards off a bench for 10 shot groups and they are good rifles. My 10-22 will add 3/4" to that. Yes, I'll get 5 shot groups down under and inch from time to time, but I think 10 shots tells the truth better and 25-50 shots is even more so.
I don't know what to tell you about your gun. For popping gophers out to 75 yards or so I'd find a nice 22 lr that fit me and put a decent sighting system on it in Weaver style mounts. Then I'd pick up a variety os 22 ammo and see what shoots best. Practice, practice, practice.
This post was edited by Bret4207 at 12:02:50 12/16/12.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Product Review: Black Tire Paint - by Staff. I have been fortunate in that two of my tractors have had rear tires that were in great shape when I bought the tractor. My model "H" even had the old style fronts with plenty of tread. My "L" fronts were mismatched Sears Guardsman snow tires, which I promptly tossed. Well, although these tires were in good shape as far as tread was concerned, they looked real sad. All were flat, but new tubes fixed that. In addition to years and years of scuffing and fading, they had paint splattered on
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.