Posted by calf on December 22, 2012 at 23:16:29 from (209.240.90.87):
JF in CT,
There is some good suggestions given here, especially about the ammo and how to hold the gun on the bench with sandbags. (Ignore all the b.s.in the other replys). One thing that has not been addressed is the barrel. Since it is used, you may want to take a look at the crown(muzzle). One that has been damaged can greatly affect accuracy. Target barrels will usually have a recessed crown to help protect it. Also, if the previous owner of the barrel, cleaned it by running the cleaning rod down from the muzzle, that can over time cause damage. Helping out at a sight-in day one time long ago, someone brought in a pump or semi-auto Remington which can only be cleaned from the muzzle, and his shots were keyholing at 25 yards. The rifling had been so badly worn away that the bullets were tumbling. If non of the other suggestions help with accuracy, you could try and remove a few inches of the barrel and then recrown it. Note that all rifle barrels need to be AT LEAST 16inches long.
Anyway, let us know how things turn out, and there is absolutely nothing wrong with liking to build more than shoot.
Good luck.
JF in CT said: (quoted from post at 02:05:46 12/16/12) After reading posts on this site for the last several years I get the impression that a lot of folks out there keep a rifle handy on their tractor to handle gophers and such. While off topic I figured I’d ask a question because I usually get better answers here than on other sites. Hopefully there are some 22 experts out there.
I just hand built up a 22 lr target rifle (my second attempt) out of a combination of old and new parts. I read that most agree that 75 yds is the best distance to zero in on. My question is; what would be considered good groups at that distance? With the scope at the maximum 9 power I’m seeing my own heart beats moving the cross hairs (I tried stopping them but each time I did I passed out…just joking). I’m seeing 3.5” groups at that distance just with the bipod (I probably need a bench rest) but I have no idea if that is considered reasonable or not. Any opinions?
This post was edited by calf at 23:18:38 12/22/12.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.