There is a 16' wide x 7' high door on the 40'side.
24' trusses are cheap.. Carter lumber here in Michigan keep them in stock, and I think they were like $50.00 each, as opposed to $96.00 for 30 foot trusses, IIRC (we rebuilt our shop in 2006, so I'm sure the prices have changed since then)
I do wish that my shop was taller, with a taller door.. and I wish the door was on the 24' end.. It's tight to pull my longbed extended cab truck in and work on it and be able to walk around it.
It wasn't my choice to build it this size.. Our original shop was 18x40x7.. we lifted the roof, changed the location of the door, and widened it to 24'.. It's dad's building, so we had to do it his way.
Here's a couple pictures:
I am in the process of buying my own place now, and it too has a 18x40 that I plan to make my shop.. My plan is to raise the roof to 10-12 feet high, 24' trusses, then "lean to" off the back another 6-8 feet, leaving me a 30 or 32x 40 shop, 24' being 10 to 12' high, and the remaining 6-8' sloping lower.. But, I don't actively farm, and I don't see myself ever buying "big" tractors, so it should be fine for me.. I'm trying to keep it a relatively inexpensive build, but have a decent sized building that is economical to heat in the end.
I will agree that the bigger you build it, the more stuff you will shove into it. I try to only keep projects in my shop for the most part, and either my loader tractor (in the pictures), or my Cub in there, since they start and drive, and can quickly moved outside to pull something else is inside. The door being closer to one end than the other helps too.. There's about 8' "north" of the big door, then the 16' door.. that leaves enough room to the south that I can park 2 of my "small, long term project" tractors side by side, have room to walk all around them, and they are not hanging into the doorway.
Like a few of the others have said: Do what you can afford.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.