Posted by andy r on April 25, 2013 at 19:56:16 from (75.91.149.15):
In Reply to: Re: batch dryers posted by SD Pete on April 25, 2013 at 10:14:38:
I have ran the Behlen 500 and it was a good dryer. The corn does not move once in the dryer and I am sure some places gets a little dryer and some places might be a little wetter, but it all gets mixed when it comes out and is at a perfect moisture percentage. The fan blades on a Behlen have an adjustable pitch so the dryer can accomodate various hp tractors from an Famall M to a JD 4520. The guy I bought it from ran it with a Deere 4520. I left the blades the same and ran it with a Farmall 706. Since the corn doesn't move it doesn't get ground up much. Not a bad dryer overall. Loading and unloading are a little more complicated than a Tox-o-wik. I now have two Tox-o-wik dryers. The corn is always moving so it drys very uniform. Loading and unloading is simple. Takes less horsepower as the fan isn't as big. Not near as much static pressure in a Tox-o-wik. I think the owners manual might say a good 3 bottom tractor might run one. They are not as noisy either. Most all of the parts are generic - belts, bearings, shafts, augers, electrical. I grew up using batch dryers and my farms don't have the best electrical service so batch drying works OK for me. Also, one of the most important things is I know what is in the grain bin. I do dry in the dryer and cool in the bin. I bring 500 bushel in, fill the dryer, start drying, and go back to the field. The dryer shuts off at a certain grain temperature which corresponds to a certain moisture %. Sometimes the heat is still on and sometimes most of the cooling is done - just depends on the moisture of the corn you are combining. Over the years I have rebuilt about everything on them. Bearings go bad, auger flighting wears out, belts wear out, the bottom metal "boot" or "sump" rusts out, and flame sensors go bad. I don't think it really costs much if any more to dry with a batch dryer than a bin dryer if you take into consideration everything. Stirators aren't the most trouble free device. I do like the Tox-o-wik better than the Behlen.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
