Posted by John T on June 10, 2014 at 13:07:11 from (216.249.72.121):
In Reply to: Wiring a Shop posted by Jiles on June 10, 2014 at 11:45:40:
True, this has been often discussed,,,,,, and true with mixed advice, some which is professional, educated, correct and current NEC code compliant, other that is Billy Bob or Bubbas (wired their own house over a case of beer and by golly it works) which is incorrect and potentially hazardous, your money, your life, your risk and your choice which to follow.
Here is my advice (retired Electrical Engineer and not current on latest codes as the many fine still practicing professional electricians here) feel free to take or leave it. NO WARRANTY it may or may not be correct (too long retired), I'm NOT saying it is or it isn't, so there lol
If you're wiring a separate buildings 120/240 volt Single Phase Three Wire Sub Panel fed by a Main Panel in the house, under the latest code as far as I know, NO WARRANTY BILLY BOB so don't have a calf if its incorrect!!
Run 4 wires out, Two Ungrounded Hot Phase Conductors ,,,,,One GrounDED Conductor (Neutral),,,,,,,One Equipment GroundING Conductor
At the remote sub panel (Unlike at the main) keep the Ground Buss (Green and Bare equipment GroundING Conductors) and the Neutral Busses (Whites) separate and electrically isolated.
The panels metallic box/tub, same as any other non conducting metal enclosures, gets connected to the Ground Buss
Any buildings electrical service, as far as I know (unless code has changed), requires earth grounding to a proper Grounding Electrode using a Grounding Electrode Conductor (I used No. 4 bare copper). A Grounding Electrode may consist of buried conductive water pipes or structural or foundation steel or what are called "made electrodes" such as copper rod or rods driven into the earth. In our jurisdiction we bonded all readily available grounding electrodes and if no other were present we used "made" electrode(s). Check with local authority and utility provider. Since this is a sub panel in a remote separate building the Grounding Electrode via the Grounding Electrode Conductor is connected to the Ground Buss.
The wire size to the remote location depends on the wire used, the enclosure and/or direct burial or aerial etc. etc., and the distance and amperage.
SO THERE now feel free to go with "mixed advice" or educated experienced advice from professionals, or advice from lay persons or Billy Bob and Bubba or whom you please. DO NOT NECESSARILY GO WITH MINE although I practiced this for years as an engineer, I been retired too long. Electrical and legal questions often draw everyone out of the woodwork all of whom are experts (although a few indeed are) you know, so my final advice is to consult with local authority and the utility provider and go with competent professional advice versus lay persons.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.