Posted by Billy NY on June 17, 2014 at 11:09:21 from (66.67.105.23):
In Reply to: Re: new business posted by Notjustair on June 17, 2014 at 10:16:01:
The only problem with topping, and or taking big limbs in one shot, is there is no control, you are not tied off independently, the reaction of the severed top, limb, (I'm aware the old timers did it during timber harvests but those don't have spread canopies, just a main trunk and limbs) or trees with a spread canopy, is so unpredictable, you put yourself at serious risk of injury, death, paralysis, and whatever else. I've misjudged the lean on occasion but on the ground with a clear path out, sure it pinched the bar, have to put a line on it, take off the power head, pull it over to get the bar back or whatever, but doing that while up onto the tree..... no way. This can't be real, if it is, I don't even know what to say to that, better him than me.
Its hard to even believe this fool is actually attempting this, the wind, the top itself, could go in any direction, and he's on a ladder, nothing to tie off too, well only the trunk.
There was one on liveleak, someone sent my another video, and while looking for the one he sent, I found one where a guy climbed up a tree, with a good sized canopy, put his one leg in a crotch, cut a large limb and it came down like a guillotine, snapped his leg just about in 2, it was a flapper, he had to drop his nice stihl saw to the ground, then be rescued, lucky he did not fall and the end of the video shows him post surgery before the cast, it looked like a shark bit into his calf, the nurse was removing a dressing at that point, not sure what was next, given the 2 full length incision, maybe they had to use something else so they could monitor it for infection, its so offensive, I would not post a link to it here. I think its wise to either get the right equipment, hire someone who has the equipment or just leave it be until such time it can be safely dealt with.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - A Lifetime of Farm Machinery - by Joe Michaels. I am a mechanical engineer by profession, specializing in powerplant work. I worked as a machinist and engine erector, with time spent overseas. I have always had a love for machinery, and an appreciation for farming and farm machinery. I was born and raised in Brooklyn, New York. Not a place one would associate with farms or farm machinery. I credit my parents for instilling a lot of good values, a respect for learning, a knowledge of various skills and a little knowledge of farming in me, amo
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.