Posted by andy r on July 27, 2014 at 22:38:37 from (75.91.149.15):
In Reply to: Moving a grain bin posted by Tramway guy on July 27, 2014 at 18:36:31:
I have moved three 18 foot bins. One was a 5 ring which I added 2 more rings (40 miles). One was a 7 ring (73 miles) and the last one was 6 and 1/2 (43 miles). Moved them all on my 16 foot car trailer. I preferred to take most all of the rings off leaving the roof and two rings. That way I was for sure I was not going to rip down someone's power lines. Down to two rings allowed me to focus just on the width, driving a more consistant speed and not stopping to check for height. Fourteen foot would be a breeze. Eighteen foot wasn't all that bad. I plotted the course to the farm everytime I went to dissassemble the bin. I tried to use gravel roads where ever possible. Paved county roads are good too. Had to go on a couple state highways for short distances. Even with 18 foot bins you could always stay on your side of the road. Had a red flag on each side. Moved them on early Sunday morning. No one is on the road. Eventually you will see the early bird church ladies. First time I had someone ahead of me or moved them behind me depending on the road. Second and third time I trailered them myself. Never tried dropping the top half into a seam openned bottom half. It would work. I just found it easier to make two trips. After the bottom rings are off and the bin is still in the air some, back the trailer underneath with two big bridge planks across it. Crawl in underneath the bin and pull in down with ratching cable pullers. Put in four eye bolts in the place of bin bolts spaced around the bin. Use some good washers on the outside. Hook the cable puller to these eye bolts and the trailer. I have probably moved at speeds approaching 40 mph on a good county road. When a car approaches pull over and slow down. When there are no other vehicles around I go down the middle of the road. Each bin holds about 4500 peaked into the roof with floors and fans. I have larger bins and personally I don't think I could move them. 18' is about wide enough on a car trailer. One bin I used new bolts and washers and one bin I used the old bolts with new washers from Fastenal.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Ferguson System Principal An implement cutting through the soil at a certain depth say eight inches requires a certain force or draft to pull it. Obviously that draft will increase if the implement runs deeper than eight inches, and decrease if it runs shallower. Why not use that draft fact to control the depth of work automatically? The draft forces are
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
